TP Link Technologies HS110V2 Smart Wi-Fi Plug with Energy Monitoring User Manual

TP-Link Technologies Co., Ltd. Smart Wi-Fi Plug with Energy Monitoring

User Manual

Quick Start GuideSupportVisit www.tp-link.com/support for technical support and troubleshooting information.7106507172  REV 2.0.0Smart Wi-Fi Plug Installation1 Download Kasa for Mobile from the App Store or Google Play.2  Connect your mobile device to a 2.4GHz Wi-Fi network.3 Launch Kasa and follow the app instructions to connect the Smart Plug to your network.Note: The Smart Plug only supports the 2.4GHz networks.Sketch9:41 AM 100%Power up your Smart PlugPlug in your Smart Plug. The Wi-Fi light will turn solid amber.NEXTSketch9:41 AM 100%DONEGreat!Your Smart Plug is all set up. It is now saved in your Device List.Add Device  Sketch9:41 AM 100%Smart Plug Smart Plug MiniSmart BulbSmart SwitchOR scan QR codeHS110
Smart Wi-Fi PlugPress and hold for 5 seconds or until the Wi-Fi LED blinks amber and green to initiate the app onboarding process.Press and hold for 10 seconds or until the Wi-Fi LED blinks amber rapidly to factory reset.Blinking amber and green: App onboarding process.Blinking green: Connecting to the network.Green: Network connection established.Blinking amber: Factory resetting.Amber: Rebooting.Red: No network connection.Green: The Smart Plug is switched on.Off: The Smart Plug is switched off.USB Port (HS110 Only): Charge your USB-powered electronic devices. Maximum output current: 1000mA (1A).Troubleshooting1.  What devices can I control with the Smart Plug?You can control lights, electronics and small appliances such as humidifiers, air purifiers, portable heaters and fans. 2.  What should I do when I can’t control the connected device?•  Check that the connected device is switched to ON.•  Make sure your mobile device and the Smart Plug are on the same Wi-Fi network.• Enable Remote Control to control the connected device from outside your home.3.  What should I do when the Wi-Fi LED is lit red?A red LED light indicates no network connection.•  Check your network connectivity. •  Relocate the Smart Plug. Avoid placing the Smart Plug near potential sources of radio signal interference.•  Repeat the app onboarding process.•  Factory reset the Smart Plug and try to add it again.4.  How do I pair the Smart Plugs with Amazon Echo?Visit www.tp-link.com/en/faq-944.html or within the Kasa Help section for pairing instructions.© 2017 TP-Link. All rights reserved. Supported Load Types:Coffee Maker: 800WDesk Lamp: 235.2WLCD: 270WHeater: 1500WHumidifier: 260WIron: 1500WToaster: 850WTower Fan: 50W
FCC STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digitaldevice, pursuant to part 15 of the FCC Rules. These limits are designed to providereasonable protection against harmful interference in a residential installation. Thisequipment generates, uses and can radiate radio frequency energy and, if not installedand used in accordance with the instructions, may cause harmful interference to radiocommunications. However, there is no guarantee that interference will not occur in aparticular installation. If this equipment does cause harmful interference to radio ortelevision reception, which can be determined by turning the equipment off and on, theuser is encouraged to try to correct the interference by one or more of the followingmeasures:Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.Consult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions:1)This device may not cause harmful interference.2)This device must accept any interference received, including interference that maycause undesired operation.Any changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.Note: The manufacturer is not responsible for any radio or TV interference caused byunauthorized modifications to this equipment. Such modifications could void the user’sauthority to operate the equipment.FCC RF Radiation Exposure Statement:This equipment complies with FCC RF radiation exposure limits set forth for anuncontrolled environment. This device and its antenna must not be co-located oroperating in conjunction with any other antenna or transmitter.“To comply with FCC RF exposure compliance requirements, this grant is applicable toonly Mobile Configurations. The antennas used for this transmitter must be installed toprovide a separation distance of at least 20 cm from all persons and must not beco-located or operating in conjunction with any other antenna or transmitter.”Canadian Compliance StatementThis device complies with Industry Canada license-exempt RSSs. Operation is subject tothe following two conditions:3)This device may not cause interference, and
4)This device must accept any interference, including interference that may causeundesired operation of the device.Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareilsradio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :5)l’appareil ne doit pas produire de brouillage;6)l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, meme si lebrouillage est susceptible d’en compromettre le fonctionnement.Radiation Exposure Statement:This equipment complies with IC radiation exposure limits set forth for an uncontrolledenvironment. This equipment should be installed and operated with minimum distance20cm between the radiator & your body.Déclaration d'exposition aux radiations:Cet équipement est conforme aux limites d'exposition aux rayonnements IC établies pourun environnement non contrôlé. Cet équipement doit être installé et utilisé avec unminimum de 20 cm de distance entre la source de rayonnement et votre corps.Industry Canada StatementCAN ICES-3 (B)/NMB-3(B)NCC Notice注意!依據 低功率電波輻射性電機管理辦法第十二條 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性或功能。第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前項合法通信,指依電信規定作業之無線電信。低功率射頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。BSMI Notice安全諮詢及注意事項請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。注意防潮,請勿將水或其他液體潑灑到本產品上。插槽與開口供通風使用,以確保本產品的操作可靠並防止過熱,請勿堵塞或覆蓋開口。請勿將本產品置放於靠近熱源的地方。除非有正常的通風,否則不可放在密閉位置中。請不要私自打開機殼,不要嘗試自行維修本產品,請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідністьвимогам нормативних документів та вимогам, що передбачені чиннимизаконодавчими актами України.Safety InformationKeep the device away from water, fire, humidity or hot environments.Do not attempt to disassemble, repair, or modify the device.Do not use damaged charger or USB cable to charge the device.Do not use any other chargers than those recommendedDo not use the device where wireless devices are not allowed.The socket-outlet shall be installed near the equipment and shall be easilyaccessible.For passthrough devices, plug the power strips into the integratedelectrical sockets of the devices, but devices of the same or another typenot be stacked in normal use.Use only power supplies which are provided by manufacturer and in theoriginal packing of this product.Please read and follow the above safety information when operating thedevice. We cannot guarantee that no accidents or damage will occur due toimproper use of the device. Please use this product with care and operate atyour own risk.

Navigation menu