TP Link Technologies TDW8901G 54M Wireless ADSL2+ Router User Manual User Guide REV1

TP-Link Technologies Co., Ltd. 54M Wireless ADSL2+ Router User Guide REV1

User Guide REV1

TD-W8901G54M Wireless ADSL2+ Router Rev˖1.0.0
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. ®is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2008 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.http://www.tp-link.com
FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:x Reorient or relocate the receiving antenna. x Increase the separation between the equipment and receiver. x Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. x Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures.
National Restrictions 2400.0-2483.5 MHz Country Restriction Reason/remark Bulgaria General authorization required for outdoor use and public service France Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5 MHz Military Radiolocation use. Refarming of the 2.4 GHz band has been ongoing in recent years to allow current relaxed regulation. Full implementation planned 2012 Italy If used outside of own premises, general authorization is required Luxembourg None General authorization required for network and service supply(not for spectrum) Norway Implemented This subsection does not apply for the geographical area within a radius of 20 km from the centre of Ny-Ålesund Russian Federation Only for indoor applications )Note:Please don’t use the product outdoor In france.
Package contents The following contents should be found in your box: ¾ TD-W8901G 54M Wireless ADSL2+ Router ¾ DC power Adapter for TD-W8901G ADSL2+ Router ¾ Quick Installation Guide ¾ RJ45 cable ¾ 2 RJ11 cables ¾ ADSL splitter (only for Annex A) ¾ Resource CD , including: z This User Guide z Other Helpful Information )Note:If any of the listed contents are damaged or missing, please contact the retailer from whom you purchased the product for assistance.
CONTENTSChapter 1 Introduction .........................................................................................11.1 Product Overview.................................................................................. 11.2 Main Features .......................................................................................11.3 Conventions .......................................................................................... 2Chapter 2 Hardware Installation..........................................................................32.1 The Front Panel ....................................................................................32.2 The Back Panel..................................................................................... 42.3 Installation Environment........................................................................ 42.4 Connecting the Router .......................................................................... 5Chapter 3 Quick Installation Guide ..................................................................... 73.1 Configure PC......................................................................................... 73.2 Login ...................................................................................................10Chapter 4 Software Configuration .................................................................... 144.1 Status..................................................................................................144.2 Quick Start ..........................................................................................154.3 Interface Setup....................................................................................154.3.1 Internet .................................................................................................... 154.3.2 LAN ......................................................................................................... 204.3.3 Wireless................................................................................................... 234.4 Advanced Setup.................................................................................. 284.4.1 Firewall .................................................................................................... 284.4.2 Routing .................................................................................................... 284.4.3 NAT ......................................................................................................... 294.4.4 QoS ......................................................................................................... 334.4.5 VLAN....................................................................................................... 344.4.6 ADSL....................................................................................................... 364.5 Access Management........................................................................... 374.5.1 ACL ......................................................................................................... 374.5.2 Filter ........................................................................................................ 384.5.3 SNMP ...................................................................................................... 464.5.4 UPnP ....................................................................................................... 464.5.5 DDNS ...................................................................................................... 474.5.6 CWMP ..................................................................................................... 47
4.6 Maintenance........................................................................................ 484.6.1 Administration.......................................................................................... 494.6.2 Time Zone ............................................................................................... 494.6.3 Firmware.................................................................................................. 514.6.4 System Restart........................................................................................ 534.6.5 Diagnostic................................................................................................ 534.7 Help..................................................................................................... 53Appendix A: Specification.....................................................................................55
TD-W8901G 54M Wireless ADSL2+ Router User Guide1Chapter 1 Introduction1.1 Product Overview Thank you for choosing the TD-W8901G 54M Wireless ADSL2+ Router. The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or 802.11g/802.11b wireless network. The TD-W8901G connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connected to the Internet using a single Wide Area Network (WAN) interface and single global IP address. The advanced security enhancements, IP/MACFilter,Application Filter and URL Filter can help to protect your network from potentially devastating intrusions by malicious agents from the outside of your network. Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the configuration. Network and Router management is done through the Web-based Utility which can be accessed through local Ethernet using any web browser. ADSLThe TD-W8901G supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer. WirelessIn the most attentive wireless security, the Router provides multiple protection measures. It can be set to turn off the wireless network name (SSID) broadcast so that only stations that have the SSID can be connected. The Router provides wireless LAN 64/128-bit WEP encryption security, WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security. 1.2 Main Features ¾ 4 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), 1 RJ11 port. ¾ Provides external splitter. ¾ Adopts Advanced DMT modulation and demodulation technology. ¾ Supports bridge mode and Router function. ¾ Multi-user sharing a high-speed Internet connection. ¾ Supports downstream transmission rates of up to 24Mbps and upstream transmission rates of 1Mbps. ¾ Supports long transfers, the max line length can reach to 6.5Km. ¾ Supports remote configuration and management through SNMP and CWMP.
TD-W8901G 54M Wireless ADSL2+ Router User Guide2¾ Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle. ¾ Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit. ¾ High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth. ¾ Supports All ADSL industrial standards. ¾ Compatible with all mainstream DSLAM (CO). ¾ Provides integrated access of internet and route function which face to SOHO user. ¾ Real-time Configuration and device monitoring. ¾ Supports Multiple PVC (Permanent Virtual Circuit). ¾ Built-in DHCP server. ¾ Built-in firewall, supporting IP/MAC filter, Application filter and URL filter. ¾ Supports Virtual Server, DMZ host and IP Address Mapping. ¾ Supports Dynamic DNS, UPnP and Static Routing. ¾ Supports system log and flow Statistics. ¾ Supports firmware upgrade and Web management. ¾Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security. ¾ Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List). ¾Supports DYING GASP (For the regions who demand). 1.3 ConventionsThe Router or device mentioned in this User guide stands for TD-W8901G without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation.
TD-W8901G 54M Wireless ADSL2+ Router User Guide3Chapter 2 Hardware Installation 2.1 The Front Panel Figure 2-1The LEDs locates on the front panel, they indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation:Name Status Description Off No Power Power On Power on Off No data transmitting or receiving on WAN port System Quick Flash There is data transmitting or receiving on WAN port On Connected the LINE port to ISP network ADSL flash Connecting to the ISP network or Connection abnormal Off The Wireless function is disabled Slow flash The Wireless function is enabled WLANQuick flash Sending or receiving data over wireless network Off There is no device linked to the corresponding port On Connected to a device through the corresponding port LAN(1-4) Flashing Sending or receiving data over corresponding port
TD-W8901G 54M Wireless ADSL2+ Router User Guide42.2 The Back Panel Figure 2-2¾POWER: The Power plug is where you will connect the power adapter. ¾RESET: There are two ways to reset the Router's factory defaults. Method one: Press the reset button of the Router; keep the reset button pressed down for more than five seconds.Method two: Restore the default setting from “Maintenance-SysRestart” of the Router's Web-based Utility. ¾1, 2, 3, 4 (LAN): Through the port, you can connect the Router to your PC or the other Ethernet network devices. ¾LINE: Through the port, you can connect the router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to 2.4. ¾Antenna: Used for wireless operation and data transmit. )Note:There is an additional printed antenna with 0 dBi gain. Without external antenna, you can also connect the Router to your PC or the other Ethernet network devices by close quarters. 2.3 Installation Environment ¾ The Product should not be located where it will be exposed to moisture or excessive heat. ¾ Place the Router in a location where it can be connected to the various devices as well as to a power source. ¾ Make sure the cables and power cord are placed safely out of the way so they do not create a tripping hazard. ¾ The Router can be placed on a shelf or desktop. ¾ Keep away from the strong electromagnetic radiation and the device of electromagnetic sensitive.
TD-W8901G 54M Wireless ADSL2+ Router User Guide52.4 Connecting the Router Before installing the device, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact your ISP. Before cable connection, cut off the power supply and keep your hands dry. You can follow the steps below to install it. Step 1: Connect the ADSL Line. Method one: Plug one end of the twisted-pair ADSL cable into the ADSL LINE port on the rear panel of TD-W8901G, and insert the other end into the wall socket.Method two˖You can use a separate splitter. External splitter can divide the data and voice, and then you can access the Internet and make calls at the same time. The external splitter has three ports: 噝 LINE: Connect to the wall jack 噝 PHONE: Connect to the phone sets 噝 MODEM: Connect to the ADSL LINE port of TD-W8901G Plug one end of the twisted-pair ADSL cable into the ADSL LINE port on the rear panel of TD-W8901G. Connect the other end to the MODEM port of the external splitter. Step 2: Connect the Ethernet cable. Attach one end of a network cable to your computer’s Ethernet port or a regular hub/switch port, and the other end to the LAN port on the TD-W8901G. Step 3: Power on the computers and LAN devices. Step 4: Attach the power adapter. Connect the power adapter to the power connector on the rear of the device and plug in the adapter to a wall outlet or power extension.
TD-W8901G 54M Wireless ADSL2+ Router User Guide6Figure 2-3
TD-W8901G 54M Wireless ADSL2+ Router User Guide7Chapter 3 Quick Installation Guide 3.1 Configure PC After you directly connect your PC to the TD-W8901G or connect your adapter to a Hub/Switch which has connected to the Router, you need to configure your PC’s IP address. Follow the steps below to configure it. Step 1: Click the Start menu on your desktop, right click My Network Places, and then select Properties (shown in Figure 3-1).Figure 3-1Step 2: Right click Local Area Connection (LAN), and then select Properties.
TD-W8901G 54M Wireless ADSL2+ Router User Guide8Figure 3-2Step 3: Select General tab, highlight Internet Protocol (TCP/IP), and then click the Propertiesbutton.
TD-W8901G 54M Wireless ADSL2+ Router User Guide9Figure 3-3Step 4: Configure the IP address as Figure 3-4 shows. After that, click OK.Figure 3-4)Note:You can configure the PC to get an IP address automatically, select “Obtain an IP address automatically” and “Obtain DNS server address automatically” in the screen above. Now, you can run the Ping command in the command prompt to verify the network connection. Please click the Start menu on your desktop, select run tab, type cmd or command in the field and press Enter. Type ping 192.168.1.1 on the next screen, and then press Enter.If the result displayed is similar to the screen below, the connection between your PC and the Router has been established.
TD-W8901G 54M Wireless ADSL2+ Router User Guide10Figure 3-5If the result displayed is similar to the screen shown below, it means that your PC has not connected to the Router. Figure 3-6You can check it follow the steps below: 1) Is the connection between your PC and the Router correct? The LEDs of LAN port which you link to the device and the LEDs on your PC's adapter should be lit. 2) Is the TCP/IP configuration for your PC correct? If the Router's IP address is 192.168.1.1, your PC's IP address must be within the range of 192.168.1.2 ~ 192.168.1.254. 3.2 LoginOnce your host PC is properly configured, please proceed as follows to use the Web-based Utility: Start your web browser and type the private IP address of the Router in the URL field: 192.168.1.1.After that, you will see the screen shown below, enter the default User Name admin and the default Password admin, and then click OK to access to the Quick Setup screen. You can follow the steps below to complete the Quick Setup.
TD-W8901G 54M Wireless ADSL2+ Router User Guide11Figure 3-7Step 1: Select the Quick Start tab, then click RUN WIZARD, and you will see the next screen. Click the NEXT button. Figure 3-8Step 2: Change the login password in the next screen, and then click the NEXT button. Figure 3-9Step 3: Configure the time for the Router, and then click the NEXT button.
TD-W8901G 54M Wireless ADSL2+ Router User Guide12Figure 3-10 Step 4: Select the connection type to connect to the ISP (We select PPPoE/PPPoA mode for example here), and then click the NEXT button. Figure 3-11 Step 5: Configure the following options provided by your ISP: Username,Password, VPI,VCIand Connection Type. Then click Next.Figure 3-12
TD-W8901G 54M Wireless ADSL2+ Router User Guide13)Note:If the PVC uses the same VPI/VCI as the default PVCs in factory configuration, you will have an Error Message “ERROR: FAIL TO UPDATE DUE TO... Duplicate to a VPI/VCI! ”. In this condition, please configure the PVC manually. To get detailed information, please refer to 4.3.1.
TD-W8901G 54M Wireless ADSL2+ Router User Guide14Step 6: Click NEXT to finish the Quick Start. Figure 3-13 Chapter 4 Software Configuration This User Guide recommends using the “Quick Installation Guide” for first-time installation. For advanced users, if you want to know more about this device and make use of its functions adequately, maybe you will get help from this chapter to configure the advanced settings through the Web-based Utility. After your successful login, you can configure and manage the device. There are main menus on the top of the Web-based Utility; submenus will be available after you click one of the main menus. On the center of the Web-based Utility, there are the detailed configurations or status information. To apply any settings you have altered on the page, please click the SAVE button.4.1 Status Choose “Status”, you can see the next submenus: Device Info,System Log and Statistics.Click any of them, and you will be able to configure the corresponding function. Figure 4-1Choose “StatusėDevice Info” menu, and you will be able to view the device information, including LAN, WAN and ADSL. The information will vary depending on the settings of the Router configured on the Interface Setup screen.
TD-W8901G 54M Wireless ADSL2+ Router User Guide15Figure 4-2)Note:Click the other submenus System Log or Statistics in Figure 4-2, and you will be able to view the system log and traffic statistics about the Router. 4.2 Quick Start Please refer to " 3.2: Login".4.3 Interface Setup Choose “Interface Setup”, you can see the next submenus: Internet and LAN.Figure 4-3Click any of them, and you will be able to configure the corresponding function. 4.3.1 InternetChoose “Interface SetupėInternet” menu, you can configure the parameters for WAN ports in the next screen (shown in Figure 4-4).
TD-W8901G 54M Wireless ADSL2+ Router User Guide16Figure 4-4¾ATM VC: ATM settings are used to connect to your ISP. Your ISP provides VPI (Virtual Path Identifier), VCI (Virtual Channel Identifier) settings to you. In this Device, you can totally setup 8 VCs on different encapsulations, if you apply 8 different virtual circuits from your ISP. You need to activate the VC to take effect. For PVCs management, you can use ATM QoS to
TD-W8901G 54M Wireless ADSL2+ Router User Guide17setup each PVC traffic line's priority. xVirtual Circuit: Select the VC number you want to setup, PVC0~PVC7. xStatus: If you want to use a designed VC, you should activate it. xVPI: Identifies the virtual path between endpoints in an ATM network. The valid range is from 0 to 255. Please input the value provided by your ISP. xVCI: Identifies the virtual channel endpoints in an ATM network. The valid range is from 32 to 65535 (1 to 31 is reserved for well-known protocols). Please input the value provided by your ISP. xPVCs Summary: Click the button, and you can view the summary information about the PVCs.xQoS: Select the Quality of Service types for this Virtual Circuit, including CBR (Constant Bit Rate), UBR (Unspecified Bit Rate) and VBR (Variable Bit Rate). These QoS types are all controlled by the parameters specified below, including PCR (Peak Cell Rate), SCR (Sustained Cell Rate) and MBS (Maximum Burst Size), please configure them according your needs. ¾Encapsulation: There are four connection types: Dynamic IP Address, Static IP Address, PPPoA/PPPoE and Bridge Mode. Please choose the designed type that you want to use. After that, you should follow the configuration below to proceed. 1) Dynamic IP Address Select this option if your ISP provides you an IP address automatically. This option is typically used for Cable services. Please enter the Dynamic IP information accordingly. Figure 4-5¾Encapsulation: Select the encapsulation mode for the Dynamic IP Address, you can leave it default.¾NAT: Select this option to Enable/Disable the NAT (Network Address Translation) function for this VC. The NAT function can be activated or deactivated per PVC basis.
TD-W8901G 54M Wireless ADSL2+ Router User Guide18¾Default Route: If enable this function, the current PVC will be considered as the default gateway to internet from this device. ¾TCP MTU Option: Enter the TCP MTU as your desire. ¾Dynamic Route: Select this option to specify the RIP (Routing Information protocol) version for WAN interface, including RIP1,RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format.xDirection: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADLS router will only accept but will not send RIP packet. OUT only means the ADLS router will only send but will not accept RIP packet. ¾Multicast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports both IGMP version 1 (IGMP v1) and IGMP v2. Select “Disabled” to disable it. 2) Static IP Address Select this option if your ISP provides static IP information to you. You should set static IP address, IP subnet mask, and gateway address in the screen below (shown in Figure 4-6). Figure 4-6)Note:Each IP address entered in the fields must be in the appropriate IP form, which is four IP octets separated by a dot (x.x.x.x), such as 192.168.1.100. The Router will not accept the IP address if it is not in this format.
TD-W8901G 54M Wireless ADSL2+ Router User Guide193) PPPoA/PPPoE Select this option if your ISP requires you to use a PPPoE connection. This option is typically used for DSL services. Select Dynamic PPPoE to obtain an IP address automatically for your PPPoE connection. Select Static PPPoE to use a static IP address for your PPPoE connection. Please enter the information accordingly. Figure 4-7¾Servicename: Enter a name to mark current connection, or you can leave it blank.¾Username: Enter your username for your PPPoE/PPPoA connection. ¾Password: Enter your password for your PPPoE/PPPoA connection. ¾Encapsulation: For both PPPoE/PPPoA connection, you need to specify the type of Multiplexing, either LLC or VC Mux. ¾Bridge Interface: Activate the option, and the Router can also work in Bridge mode. ¾Connection: For PPPoE/PPPoA connection, you can select Always on or Connect
TD-W8901G 54M Wireless ADSL2+ Router User Guide20on-Demand or Connect Manually. Connect on demand is dependent on the traffic. If there is no traffic (or Idle) for a pre-specified period of time), the connection will tear down automatically. And once there is traffic send or receive, the connection will be automatically on.¾Static/Dynamic IP Address: For PPPoE/PPPoA connection, you need to specify the public IP address for this ADSL Router. The IP address can be either dynamically (via DHCP) or given IP address provided by your ISP. For Static IP, you need to specify the IP address, Subnet Mask and Gateway IP address. ¾Default Route: You should select Yes to configure the PVC as the default gateway to internet from this device. ¾MAC Spoofing: Enable the MAC Spoofing, and enter a MAC address to configure the WAN port. It makes your inside network appear as a device with this MAC address to the outside world.4) Bridge Mode If you select this type of connection, the modem can be configured to act as a bridging device between your LAN and your ISP. Bridges are devices that enable two or more networks to communicate as if they are two segments of the same physical LAN. Figure 4-8)Note:After you finish the Internet configuration, please click SAVE to make the settings take effect. 4.3.2 LANChoose “Interface SetupėLAN” menu, and you will see the LAN screen (shown in Figure 4-9). Please configure the parameters for LAN ports according to the descriptions below.
TD-W8901G 54M Wireless ADSL2+ Router User Guide21Figure 4-9¾Router Local IP: These are the IP settings of the LAN interface for the device. These settings may be referred to as Private settings. You may change the LAN IP address if needed. The LAN IP address is private to your internal network and cannot be seen on the Internet.xIP Address: Enter the Router’s local IP Address, then you can access to the Web-based Utility via the IP Address, the default value is 192.168.1.1.xIP Subnet Mask: Enter the Router’s Subnet Mask, the default value is 255.255.255.0.xDynamic Route: Select this option to specify the RIP (Routing Information protocol) version for LAN interface, including RIP1,RIP2-B and RIP2-M. RIP2-B and RIP2-M are both sent in RIP2 format, the difference is that RIP2-M using Multicast, while RIP2-B using Broadcast format. xDirection: Select this option to specify the RIP direction. None is for disabling the RIP function. Both means the ADSL Router will periodically send routing information and accept routing information, and then incorporate them into routing table. IN only means the ADLS router will only accept but will not send RIP packet. OUT only means the ADLS router will only send but will not accept RIP packet. xMulticast: Select IGMP version, or disable the function. IGMP (Internet Group Multicast Protocol) is a session-layer protocol used to establish membership in a multicast group. The ADSL ATU-R supports both IGMP version 1 (IGMP v1) and IGMP v2. Select “Disabled” to disable it.
TD-W8901G 54M Wireless ADSL2+ Router User Guide22xIGMP Snoop: Enable the IGMP Snoop function if you need. ¾DHCP Server: Select Enabled, then you will see the screen below (shown in Figure 4-10). The Router will work as a DHCP Server; it becomes the default gateway for DHCP client connected to it. DHCP stands for Dynamic Host Control Protocol. The DHCP Server gives out IP addresses when a device is booting up and request an IP address to be logged on to the network. That device must be set as a DHCP client to obtain the IP address automatically. By default, the DHCP Server is enabled. The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network. Figure 4-10 xStarting IP Address: Enter the starting IP address for the DHCP server's IP assignment. Because the default IP address for the Router is 192.168.1.1, the default Start IP Address is 192.168.1.2, and the Start IP Address must be 192.168.1.2 or greater, but smaller than 192.168.1.254. xIP Pool Count: The max user pool size. xLease Time: The length of time for the IP lease. After the dynamic IP address has expired, the user will be automatically assigned a new dynamic IP address. The default is 259200 seconds.xDNS Relay: If you want to disable this feature, you just need to set both Primary and secondary DNS IP to 0.0.0.0. If you want to use DNS relay, you can setup DNS server IP to 192.168.1.1 on their Computer. If not, the device will perform as no DNS relay. xPrimary DNS Server: Type in your preferred DNS server. xSecondary DNS Server: Type in your preferred DNS server.xCurrent Pool Summary: Click the button, then you can view the IP addresses that the DHCP Server gives out.)Note:If Use Auto Discovered DNS Server Only is selected in DNS Relay, this router will accept the first received DNS assignment from one of the PPPoA, PPPoE or MER/DHCP enabled PVC(s) during the connection establishment. If Use User Discovered DNS Server Only is selected in DNS Relay, it is necessary for you to enter the primary and optional secondary DNS server IP addresses. After type in the address, click SAVE button to save it and invoke it.
TD-W8901G 54M Wireless ADSL2+ Router User Guide23¾DHCP Relay: Select Relay, then you will see the next screen (shown in Figure 4-11), and the Router will work as a DHCP Relay. A DHCP relay is a computer that forwards DHCP data between computers that request IP addresses and the DHCP server that assigns the addresses. Each of the device's interfaces can be configured as a DHCP relay. If it is enabled, the DHCP requests from local PCs will forward to the DHCP server runs on WAN side. To have this function working properly, please run on router mode only, disable the DHCP server on the LAN port, and make sure the routing table has the correct routing entry. Figure 4-11 xDHCP Server IP for Relay Agent: Enter the DHCP server IP Address runs on WAN side.)Note:If you select Disabled, the DHCP function will not take effect. 4.3.3 Wireless Choose “Interface SetupėWireless” menu, and you will see the Wireless screen (shown in Figure 4-12 ). Please configure the parameters for wireless according to the descriptions below.
TD-W8901G 54M Wireless ADSL2+ Router User Guide24Figure 4-12 ¾Access point Settings: These are the settings of the access point. You can configure the rules to allow wireless-equipped computers and other devices to communicate with a wireless network. xAccess point: Select Activated to allow wireless station to associate with the access point.xChannel: Select the channel you want to use from the drop-down List of Channel. This field determines which operating frequency will be used. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. xBeacon Interval: Enter a value between 20-1000 milliseconds. The Beacon Interval value indicates the frequency interval of the beacon. A beacon is a packet broadcast by the Router to synchronize the wireless network. The default value is 100. xRTS/CTS Threshold: Should you encounter inconsistent data flow, only minor reduction
TD-W8901G 54M Wireless ADSL2+ Router User Guide25of the default value 2347 is recommended. If a network packet is smaller than the preset RTS threshold size, the RTS/CTS mechanism will not be enabled. The Router sends Request to Send (RTS) frames to a particular receiving station and negotiates the sending of a data frame. After receiving an RTS, the wireless station responds with a Clear to Send (CTS) frame to acknowledge the right to begin transmission. In most cases, keep its default value of 2347. xDTIM: This value, between 1 and 255, indicates the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. Its clients hear the beacons and awaken to receive the broadcast and multicast messages. The default value is 1. x802.11 b/g: In the drop-down list you can select “802.11g (54Mbps)” or “802.11b (11Mbps)”. "802.11 b+g (54Mbps & 11Mbps)", which allows both 802.11g and 802.11b wireless stations to connect to the Router. ¾Wireless MAC Address Filter: Wireless access can be filtered by using the MAC addresses of the wireless devices transmitting within your network’s RADIUS. xActive: If you wish to filter users by MAC Address, select “Activated”, and “Deactived” for don’t.xAction: To filter wireless users by MAC Address, select “Allow Association” or “Deny Association” the follow Wireless LAN station(s) association. xMAC Address: Enter the MAC Address you wish to filter in the field. ¾Multiple SSIDs Settings: These are the settings of the SSID. xSSID Index: The index of the SSID, and in this model, you can only leave it as a default value of 1.xSSID: Wireless network name shared among all points in a wireless network. The SSID must be identical for all devices in the wireless network. It is case-sensitive and must not exceed 32 characters (use any of the characters on the keyboard). Make sure this setting is the same for all stations in your wireless network. Type the desired SSID in the space provided. xBroadcast SSID: When wireless clients survey the local area for wireless networks to associate with, they will detect the SSID broadcast by the Router. To broadcast the Router’s SSID, keep the default setting. If you don’t want to broadcast the Router’s SSID, select “No”. xAuthentication Type: Select an authentication type from the drop-down list, which allows you to configure security features of the wireless LAN interface. Options available are: Disabled, WEP-64Bits, WEP-128Bits, WPA-PSK, and WPA2-PSK. )Note:For most users, it is recommended to use the default Wireless LAN Performance settings. Any changes made to these settings may adversely affect your wireless network. Under certain
TD-W8901G 54M Wireless ADSL2+ Router User Guide26circumstances, changes may benefit performance. Carefully consider and evaluate any changes to these wireless settings. 1) WEP-64Bits To configure WPA-64Bits settings, select the WPA-64Bits option from the drop-down list. The menu will change to offer the appropriate settings. WPA-64Bits is a data privacy mechanism based on a 64-bit shared key algorithm, as described in the IEEE 802.11g standard. Figure 4-13 2) WEP-128Bits To configure WPA-64Bits settings, select the WPA-64Bits option from the drop-down list. The menu will change to offer the appropriate settings. 128-bit is stronger than 64-bit. Figure 4-14 3) WPA-PSK To configure WPA-PSK settings, select the WPA-PSK option from the drop-down list. The menu will change to offer the appropriate settings. WPA-PSK requires a shared key and does not use a
TD-W8901G 54M Wireless ADSL2+ Router User Guide27separate server for authentication. PSK keys can be ASCII or Hex type. Figure 4-15 ¾Encryption: Select the encryption you want to use: Automatic, TKIP or AES (AES is an encryption method stronger than TKIP). xTKIP (Temporal Key Integrity Protocol) - a wireless encryption protocol that provides dynamic encryption keys for each packet transmitted. xAES (Advanced Encryption Standard) - A security method that uses symmetric 128-bit block data encryption. ¾Pre-Shared Key: Enter the key shared by the Router and your other network devices. It must have 8-63 ASCII characters or 64 Hexadecimal digits. 4) WPA2-PSK To configure WPA2-PSK settings, select the WPA2-PSK option from the drop-down list. The menu will change to offer the appropriate settings. WPA2-PSK requires a shared key and does not use a separate server for authentication. PSK keys can be ASCII or Hex type. Figure 4-16
TD-W8901G 54M Wireless ADSL2+ Router User Guide284.4 Advanced Setup Choose “Advanced Setup”, you can see the next submenus: Figure 4-17 Click any of them, and you will be able to configure the corresponding function. 4.4.1 Firewall Choose “Advanced SetupėFirewall” menu, and you will see the next screen (shown in Figure 4-18).Figure 4-18 ¾Firewall: Select this option can automatically detect and block Denial of Service (DoS) attacks, such as Ping of Death, SYN Flood, Port Scan and Land Attack.¾SPI: If you enable SPI, all traffics initiated from WAN would be blocked, including DMZ, Virtual Server, and ACL WAN side.4.4.2 RoutingChoose “Advanced SetupėRouting” menu, and you will see the routing information in the next screen (shown in Figure 4-19).
TD-W8901G 54M Wireless ADSL2+ Router User Guide29Figure 4-19 Click ADD ROUTE button to add a new route in the next screen (shown in Figure 4-20).Figure 4-20 ¾Destination IP Address: This parameter specifies the IP network address of the final destination.¾IP Subnet Mask: Enter the subnet mask for this destination. ¾Gateway IP Address: Enter the IP address of the gateway. The gateway is an immediate neighbor of your ADSL Router that will forward the packet to the destination. On the LAN, the gateway must be a router on the same segment as your Router; over Internet (WAN), the gateway must be the IP address of one of the remote nodes. ¾Metric: Metric represents the "cost" of transmission for routing purposes. IP Routing uses hop count as the measurement of cost, with a minimum of 1 for directly connected networks. Enter a number that approximates the cost for this link. The number need not to be precise, but it must between 1 and 15. In practice, 2 or 3 is usually a good number. ¾Announced in RIP: This parameter determines if the ADSL router will include the route to this remote node in its RIP broadcasts. If set to Yes, the route to this remote node will be propagated to other hosts through RIP broadcasts. If No, this route is kept private and is not included in RIP broadcasts. 4.4.3 NATChoose “Advanced SetupėNAT” menu, you can setup the NAT (Network Address Translation) function for the Router (shown in Figure 4-21).
TD-W8901G 54M Wireless ADSL2+ Router User Guide30Figure 4-21 ¾Virtual Circuit: Enter Virtual Circuit Index that you plan to setup for the NAT function. ¾NAT Status: This field shows the current status of the NAT function for the current VC. You can go to the previous screen (shown in Figure 4-4) to activate the function. ¾Number of IPs; This field is to specify how many IPs are provided by your ISP for current VC. It can be single IP or multiple IPs. We select Multiple to explain. )Note:For VCs with single IP, they share the same DMZ and Virtual servers; for VCs with multiple IPs, each VC can set DMZ and Virtual servers. Furthermore, for VCs with multiple IPs, they can define the Address Mapping rules; for VCs with single IP, since they have only one IP, there is no need to individually define the Address Mapping rule. 4.4.3.1 DMZChoose “Advanced SetupėNATėDMZ” in Figure 4-21, you can configure the DMZ host in the next screen. A DMZ (demilitarized zone) is a host between a private local network and the outside public network. It prevents outside users from getting direct access to a server that has company data. Users of the public network outside the company can access to the DMZ host. Figure 4-22 ¾DMZ Host IP Address: Enter the specified IP Address for DMZ host on the LAN side. 4.4.3.2 Virtual Server Choose “Advanced SetupėNATėVirtual Server” in Figure 4-21, you can configure the Virtual Server in the next screen.
TD-W8901G 54M Wireless ADSL2+ Router User Guide31The Virtual Server is the server or server(s) behind NAT (on the LAN), for example, Web server or FTP server, that you can make visible to the outside world even though NAT makes your whole inside network appear as a single machine to the outside world. Figure 4-23 ¾Rule Index: The Virtual server rule index for this VC. You can specify 10 rules in maximum. All the VCs with single IP will use the same Virtual Server rules. ¾Application: The Virtual servers can be used for setting up public services on your LAN. ¾Protocol: The protocol used for this application.¾Start & End port number: Enter the specific Start and End Port number you want to forward. If it is one port only, you can enter the End port number the same as Start port number. For example, if you want to set the FTP Virtual server, you can set the start and end port number to 21. ¾Local IP Address: Enter the IP Address for the Virtual Server in LAN side. ¾Virtual Server Listing: This displays the information about the Virtual Servers you establish. To add a virtual server entry: Step 1: Select the “Virtual Circuit” and select “Virtual Server”.)Note:For VCs with single IP, select Single; For VCs with multiple IPs, select Multiple for the option. Step 2: Select the Rule index for the rule as shown in Figure 4-23.Step 3: Select the application you want from drop-down list, then the protocol and port number will be added to the corresponding field automatically, you only need to configure the IP address for the virtual server; If the application list does not contain the service that you want, please configure the Port number, IP Address and Protocol manually. Step 4: After that, click SAVE to make the entry take effect. Other operations for the entries as shown in Figure 4-23:Enter the index of assigned entry, and click the DELETE button to delete the entry. Click the Back button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now.
TD-W8901G 54M Wireless ADSL2+ Router User Guide324.4.3.3 IP Address Mapping Select Multiple for numbers of IPs in Figure 4-21, and choose “Advanced SetupėNATėIPAddress Mapping(for Multiple IP Service)”. You can configure the Address Mapping Rule in the next screen. The IP Address Mapping is for those VCs that configured with multiple IPs. The IP Address Mapping rule is per-VC based (only for Multiple IPs' VCs). Figure 4-24 ¾Rule Index: Select the Virtual server rule index for this VC. You can specify 8 rules in maximum.¾Rule Typ: There are four types: one-to-one, Many-to-One, Many-to-Many Overload and Many-to-Many No-overload. ¾Local Start & End IP: Enter the local IP Address you plan to map to. Local Start IP is the starting local IP address and Local End IP is the ending local IP address. If the rule is for all local IPs, then the Start IP is 0.0.0.0 and the End IP is 255.255.255.255. ¾Public Start & End IP: Enter the public IP Address you want to do NAT. Public Start IP is the starting public IP address and Public End IP is the ending public IP address. If you have a dynamic IP, enter 0.0.0.0 as the Public Start IP. ¾Address Mapping List: This displays the information about the Mapping addresses. To add a mapping rule: Step 1: Select the “Virtual Circuit” and Multiple for the “Number of IPs”. Then select the tab IPAddress Mapping (shown in Figure 4-21). )Note:IP Address Mapping is only available for VCs with Multiple IPs. Step 2: Select the Rule index for the rule as shown in Figure 4-24.Step 3: Select the rule type you want from the drop-down list. Step 4: Enter the local and public IP addresses in the corresponding fields. Step 5: After that, click SAVE to make the entry take effect. Other operations for the entries as shown in Figure 4-24:Select the index of assigned entry, and click the DELETE button to delete the entry.
TD-W8901G 54M Wireless ADSL2+ Router User Guide33Click the Back button to return to the previous screen. Click the CANCEL button to cancel the configuration which is made just now. 4.4.4 QoSChoose “Advanced SetupėQoS”, you can configure the QoS in the next screen. QoS helps to prioritize data as it enters your router. By attaching special identification marks or headers to incoming packets, QoS determines which queue the packets enter, based priority. This is useful when there are certain types of data you want to give higher priority, such as voice data packets give higher priority than Web data packets. This option will provide better service of selected network traffic over various technologies. Figure 4-25 ¾QoS: Select this option to Activate/Deactivate the IP QoS on different types (IP ToS and DiffServ).¾Summary: Click the button to view the configurations of QoS.
TD-W8901G 54M Wireless ADSL2+ Router User Guide34¾Rule: Configure the rules for QoS. If the traffic complies with the rule, then the Router will take the corresponding action to deal with it.xRule Index: Select the index for the rule you want to configure.xActive: Activate the rule. The rule can take effect only when it is activated.xApplication: Select the application that the rule aimed at.xPhysical Ports: Select the port whose traffic flow are controlled by the rule.xDestination MAC & IP & Mask & Port Range: Enter the IP information about the Destination host for the rule.xSource MAC & IP & Mask & Port Range: Enter the IP information about the Source host for the rule.xProtocol ID: Select one among TCP/UDP, TCP, UDP or ICMP protocols for the application.xVlan ID Range: Enter the Vlan range, and the rule will be effective to the selected Vlans.xIPP/DS Field: Select the type of the action to assign the priority.When you select IPP/TOS, you can assign the priority via IP information. IP QoS function is intended to deliver guaranteed as well as differentiated Internet services by giving network resource and usage control to the Network operator. xIP Precedence Range: Enter the IP precedence range that the Router takes to differentiate the traffic.xType of Service: Select the type of service that the Router takes to deal with the traffic.x802.1p: Select the priority range for the rule.When you select DSCP, you can assign the priority via DHCP (the header of IP group). It maps the IP group into corresponding service class.xDSCP Range: Enter the DSCP range to differentiate the traffic.x802.1p: Select the priority range for the rule.¾Action: Configure the action that the Router takes to deal with the traffic which accord with the rule.xIPP/DS Field: Select the type for the action.xIP Precedence Remarking: Select the number to remark the priority for IP precedence. xType of Service Remarking: Select the type to remark the service.xDSCP Remarking: Enter the number to remark the DSCP priority.x802.1p Remarking: Select the type to remark the 802.1p priority.xQueue: Select the priority type for the action.4.4.5 VLANChoose “Advanced SetupėVLAN”, you can activate the VLAN function in the next screen. Virtual LAN (VLAN) is a group of devices on one or more LANs that are configured so that they can communicate as if they were attached to the same LAN, when in fact they are located on a number of different LAN segments. Because VLANs are based on logical instead of physical connections, it is very flexible for user/host management, bandwidth allocation and resource
TD-W8901G 54M Wireless ADSL2+ Router User Guide35optimization. There are two types of VLAN as follows: Port-Based VLAN: Each physical switch port is configured with an access list specifying membership in a set of VLANs. ATM VLAN: Using LAN Emulation (LANE) protocol to map Ethernet packets into ATM cells and deliver them to their destination by converting an Ethernet MAC address into an ATM address. Figure 4-26 1) Assign VLAN PVID for each Interface Click Assign VLAN PVID for each Interface in Figure 4-26, you can assign the PVID for each interface in the next screen (shown in Figure 4-27). Figure 4-27 ¾PVID: Each physical port has a default VID called PVID (Port VID). PVID is assigned to untagged frames or priority tagged frames (frames with null (0) VID) received on this port.
TD-W8901G 54M Wireless ADSL2+ Router User Guide362) Define VLAN Group Click Define VLAN Group in Figure 4-26, you can define VLAN groups in the next screen (shown in Figure 4-28). Figure 4-28 ¾VLAN Index: Select the VLAN index for this VC. You can specify 8 groups in maximum. ¾VLAN ID: This indicates the VLAN group. ¾ATM VCs: Select the ATM VCs as members of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the VC. ¾Ethernet: Select the Ethernet port as a member of VLAN. ¾Wireless LAN: Select the wireless LAN port as a member of VLAN, and if you leave the Tagged blank, the tag in frames will be deleted when transmitted from the port.¾VLAN Group Summary: This displays the information about the VLAN Groups. 4.4.6 ADSLChoose “Advanced SetupėADSL”, you can select the ADSL Type and ADSL Mode in the next screen. The ADSL feature can be selected when you meet the physical connection problem. Please check the proper settings with your Internet service provider.
TD-W8901G 54M Wireless ADSL2+ Router User Guide37Figure 4-29 ¾ADSL Mode: Select the ADSL operation mode which your ADSL connection uses. ¾ADSL Type: Select the ADSL operation type which your ADSL connection uses. 4.5 Access Management Choose “Access Management”, you can see the next submenus: Figure 4-30 Click any of them, and you will be able to configure the corresponding function. 4.5.1 ACLChoose “Access ManagementėACL”, you can see the next screen (shown in Figure 4-31). Youcan specify the client to access the ADSL Router once setting his IP as a Secure IP Address through selected applications.
TD-W8901G 54M Wireless ADSL2+ Router User Guide38Figure 4-31 ¾ACL: If Activated, the IP addresses which are contained in the Access Control List can access to the Router. If Deactivated, all IP addresses can access to the Router. ¾ACL Rule Index: Select the ACL rule index for the entry. ¾Active: Enable the ACL rule. ¾Secure IP Address: Select the IP addresses which are permitted to access to the Router remotely. With the default IP 0.0.0.0, any client would be allowed to remotely access the ADSL Router. ¾Application: Select the application for the ACL rule, and then you can access the Router through it. ¾Interface: Select the interface for access: LAN, WAN or Both. ¾Access Control of Listing: This displays the information about the ACL Rules. 4.5.2 FilterChoose “Access ManagementėFilter”, you can see the Filter screen (the default is IP/MAC Filter screen shown in Figure 4-32 ). The filtering feature includes IP/MAC Filter, Application Filter, and URL Filter. The feature makes it possible for administrators to control user's access to the Internet, protect the networks. 4.5.2.1 IP Filter Select IP/Mac Filter as the Filter type, and select IP as the Rule type (shown in Figure 4-32), then you can configure the filter rules based on IP address. The filtering includes Outgoing andIncoming, the detailed descriptions are provided below.
TD-W8901G 54M Wireless ADSL2+ Router User Guide39Figure 4-32 ¾Filter Type Selection: Select the filter type for the configuration below. ¾IP/MAC Filter Set Index: Select the Set index for the IP Filter entry. This index can match with six IP / MAC Filter Rule Indexes. ¾Interface: Select the interface for the entry. )Note:If select PVC0~PVC7 as an interface, the filter will match the IP traffic of WAN port with specified IPs (Source IP Address and Destination IP Address). If select LAN as an interface, the filter will match the IP traffic of LAN port with specified IPs. ¾Direction: Select the direction for this IP Filter rule. There are three filtering directions: Both, Incoming, Outgoing.
TD-W8901G 54M Wireless ADSL2+ Router User Guide40)Note:Incoming means that IP traffic which is coming into the router, and the Outgoing means that IP traffic which is going out the router. ¾IP/MAC Filter Rule Index: Select the Rule index for the IP Filter entry. )Note:You should set the IP/MAC Filter Set Index and IP/MAC Filter Rule Index together to appoint the address (shown in the Filter List) for the IP Filter rule. For example, (1, 2), it means the rule will be shown in the row 2 IP/MAC Filter Set Index 1. ¾Rule Type: For IP Filter, please select IP here.¾Active: Select “Yes” to make the rule to take effect.¾Source IP Address: Enter the source IP address for the rule. You can enter 0.0.0.0; it means that all IP addresses are controlled by the rule.¾Destination IP Address: Enter the destination IP address for the rule. You can enter 0.0.0.0, it means that all IP addresses are controlled by the rule. The set of Subnet Mask and Port Number are same as Source IP Address.¾Subnet Mask: Enter the Subnet Mask for the rule.¾Port Number: Enter the Port Number for the rule. You can enter 0, which means that all ports are controlled by the rule.¾Protocol: Select the protocol: TCP,UDP or ICMP for the filter rule.¾Rule Unmatched: If the current rule can not match, and you select Forward, the router will skip the rule and transmit directly. If you select Next, the router will find the next filter rule (show in Filter list) to match.¾IP/MAC Filter Listing: This displays the information about the IP Filter rules.To add an IP Address filtering entry: For example: If you desire to block E-mail received and sent by the IP address 192.168.1.7 on your local network; And wish to make the PCs with IP address 192.168.1.8 unable to visit the website of IP address 202.96.134.12, while other PCs have no limit. You can configure the rules as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1), (1, 2) and (1, 3).Step 1: Select the “IP/MAC Filter” as the Filer Type Selection (show in Figure 4-32).Select the “IP” as the Rule Type on the Filter screen, then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Both” for the first rule.
TD-W8901G 54M Wireless ADSL2+ Router User Guide41)Note:If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “Source IP Address”, “Destination IP Address”, “Subnet Mask” and “Port Number” in the corresponding field. Step 4: Select the Protocol as “TCP” and select the Unmatched rule as “Next”.Step 5: Finally, click the SAVE to save the entry.Step 6: Go to Step 2 to configure the next two rules: Block E-mail received by the IP address 192.168.1.7 on your local network; Make the PC with IP address 192.168.1.8 unable to visit the website of IP address 202.96.134.12.)Note:After you complete the IP filter rules for the example, the Filter list will show as follows. You can enter the IP / MAC Filter Set Index to view the information about the rule. Other operations for the entries as shown in Figure 4-32:Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry. Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry.
TD-W8901G 54M Wireless ADSL2+ Router User Guide424.5.2.2 MAC Filter Select IP/Mac Filter as the Filter type, and select MAC as the Rule type (shown in Figure 4-33), and then you can configure the filter rules based on MAC address. Figure 4-33 ¾Rule Type: Select MAC for the MAC Filter rule.¾Active: Select “Yes” to make the rule to take effect.¾MAC Address: Enter the MAC address for the rule. ¾Rule Unmatched: If the current rule can not match, and you select Forward, the router will skip the rule and transmit directly. If you select Next, the router will find the next filter rule (show in Filter list) to match.¾IP/MAC Filter Listing: This displays the information about the MAC Filter rules.To add a MAC Address filtering entry: For example: If you want to block the PCs with MAC addresses 00-0A-EB-00-07-BE and 00-0A-EB-00-07-5F to access the Internet, you can configure as follows. Presume the rules are both aimed at the interface PVC0, and their indexes are (1, 1) and (1, 2).Step 1: Select the “IP/MAC Filter” as the Filer Type Selection:
TD-W8901G 54M Wireless ADSL2+ Router User Guide43Select the “MAC” as the Rule Type on the Filter screen (show in Figure 4-33). , Then you can configure the specific rule for the example. Step 2: Select the IP/MAC Filter Set Index and IP/MAC Filter Rule Index for the rule, then select the Interface “PVC0”, and select the Direction “Outgoing” for the first rule. )Note:If you want to make the rule take effect, please select Yes to active the rule. Step 3: Enter the “MAC Address” and select the Unmatched rule as “Next”. Step 4: Finally, click the SAVE to save the entry.Step 5: Go to Step 2 to configure the next rule: Block the PC with MAC address 00-0A-EB-00-07-5F to access the Internet.)Note:After you complete the MAC filter rules for the example, the Filter list will show as follows. You can enter the IP / MAC Filter Set Index to view the information about the rule. Other operations for the entries as shown in Figure 4-32:Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to view or modify the entry. Select the IP / MAC Filter Set Index and IP/MAC Filter Rule Index to locate the specific rule, and then click the DELETE button to delete the entry. 4.5.2.3 Application Filter Select Application Filter as the Filter type (shown in Figure 4-34), and then you can configure the filter rules based on application.
TD-W8901G 54M Wireless ADSL2+ Router User Guide44Figure 4-34 ¾Filter Type Selection: Select the Application Filter for the next configuration. ¾Application Filter: Activate or deactivate the function. ¾ICQ & MSN & YMSG & Real Audio/Video: Select Allow or Deny for these applications. Ifyou select Allow, the Router will accept the application; if you select Deny, the Router will forbid the application.4.5.2.4 URLSelect Application Filter as the Filter type (shown in Figure 4-35), and then you can configure the filter rules based on URL.
TD-W8901G 54M Wireless ADSL2+ Router User Guide45Figure 4-35 ¾Filter Type Selection: Select the URL Filter for the next configuration. ¾Active: Select “Yes” to make the rule to take effect. ¾URL Index: Select the index for the URL Filter entry. ¾URL: Enter the URL for this URL Filter. ¾URL Filter Listing: This displays the information about the URL Filter rules. To add a URL filter entry: For example: If you want to forbid the user to access the website: www.yahoo.com. Presume the rule is aimed at the interface PVC0, and its index is “1”.Step 1: Select the “URL Filter” as the Filer Type Selection (show in Figure 4-35).Step 2: Select the Index for the rule, and then enter the website in the URL field. Step 3: Finally, Select Yes to active the rule, and then click the SAVE to save the entry.Other operations for the entries as shown in Figure 4-32:Select the URL Index to view or modify the entry. Select the URL Index to locate the specific rule, and then click the DELETE button to delete the entry.
TD-W8901G 54M Wireless ADSL2+ Router User Guide464.5.3 SNMPChoose “Access ManagementėSNMP”, you can see the SNMP screen. The Simple Network Management Protocol (SNMP) is used for exchanging information between network devices. Figure 4-36 ¾Get Community: Set the password for the incoming Get and Get next requests from the management station. ¾Set Community: Set the password for incoming Set requests from the management station. 4.5.4 UPnPChoose “Access ManagementėUPnP”, you can configure the UPnP in the screen (shown in Figure 4-37).UPnP (Universal Plug and Play) is a distributed, open networking standard that uses TCP/IP for simple peer-to-peer network connectivity between devices. An UPnP device can dynamically join a network, obtain an IP address, convey its capabilities and learn about other devices on the network. In turn, a device can leave a network smoothly and automatically when it is no longer in use. UPnP broadcasts are only allowed on the LAN. Figure 4-37 ¾UPnP: Activate or Deactivate the UPnP function. Only when the function is activated, can the UPnP take effect. ¾Auto-Configure: If you activate the function, then the UPnP network devices can automatically configure network addressing, announce their presence in the network to other UPnP devices and enable exchange of simple product and service descriptions.
TD-W8901G 54M Wireless ADSL2+ Router User Guide474.5.5 DDNSChoose “Access ManagementėDDNS”, you can configure the DDNS function in the screen (shown in Figure 4-38).The router offers a Dynamic Domain Name System (DDNS) feature. The feature lets you use a static host name with a dynamic IP address. User should type the host name, user name and password assigned to your ADSL Router by your Dynamic DNS provider. User also can decide to turn on DYNDNS Wildcard or not. Figure 4-38 ¾Dynamic DNS: Activate the DDNS function or not. ¾Service Provider: This field displays the service provider of DDNS. ¾My Host Name: Enter your host name here. ¾E-mail Address: Enter your E-mail address here. ¾Username & Password: Type the “User Name” and “Password” for your DDNS account. ¾Wildcard support: Select the option to use Wildcard function 4.5.6 CWMPChoose “Access ManagementėCWMP”, you can configure the CWMP function in the screen (shown in Figure 4-39).The router offers CWMP feature. The function supports TR-069 protocol which collects information, diagnoses the devices and configures the devices automatically via ACS (Auto-Configuration Server).
TD-W8901G 54M Wireless ADSL2+ Router User Guide48Figure 4-39 ¾CWMP: Select activate the CWMP function.¾URL: Enter the website of ACS which is provided by your ISP. ¾User Name/Password: Enter the User Name and password to login the ACS server. ¾Path: Enter the path that connects to the ACS server. ¾Port: Enter the port that connects to the ACS server. ¾User Name/Password: Enter the User Name and Password that provided the ACS server to login the router. ¾Periodic Inform: Activate or deactivate the function. If Activated, the information will be informed to ACS server periodically. ¾Interval: Enter the interval time here. 4.6 MaintenanceChoose “Maintenance”, you can see the next submenus: Figure 4-40 Click any of them, and you will be able to configure the corresponding function.
TD-W8901G 54M Wireless ADSL2+ Router User Guide494.6.1 Administration Choose “MaintenanceėAdministration”, you can set new password for admin in the screen (shown in Figure 4-41).Figure 4-41 )Note:1) There is only one account that can access Web-Management interface. The default account is "admin", and the password is "admin". Admin has read/write access privilege. 2) When you change the password, you should enter the new password twice, and then click SAVE to make the new password take effect. 4.6.2 Time Zone Choose “MaintenanceėTime Zone”, you can configure the system time in the screen (shown in Figure 4-42).The system time is the time used by the device for scheduling services. There are three methods to configure the time. You can manually set the time or connect to a NTP (Network Time Protocol) server. If a NTP server is set, you will only need to set the time zone. If you manually set the time, you may also set Daylight Saving dates and the system time will automatically adjust on those dates.1) NTP Server automatically Select NTP Server automatically as the Synchronize time, you only need to set the time zone.
TD-W8901G 54M Wireless ADSL2+ Router User Guide50Figure 4-42 )Note:The ADSL Router built-in some NTP Servers, when the Router connects to the Internet, the Router will get the system time automatically from the NTP Server. You can also configure the NTP Server address manually, and then the Router will get the time from the specific Server firstly. 2) PC’s Clock Select PC’s Clock as the Synchronize time, you don’t need to set any items. Figure 4-43 3) Manually Select Manually as the Synchronize time, you need to set the date and time corresponding to the current time.
TD-W8901G 54M Wireless ADSL2+ Router User Guide51Figure 4-44 4.6.3 Firmware Choose “MaintenanceėFirmware”, you can upgrade the firmware of the Router in the screen (shown in Figure 4-45). Make sure the firmware or romfile you want to use is on the local hard drive of the computer. Click Browse to find the local hard drive and locate the firmware or romfile to be used for upgrade. Figure 4-45 To upgrade the router's firmware, follow these instructions below: Step 1: Download a more recent firmware upgrade file from the TP-LINK website (www.tp-link.com).Step 2: Type the path and file name of the update file into the “New Firmware Location” field. Or click the Browse button to locate the update file. Step 3: Click the UPGRADE button. )Note:1) New firmware versions are posted at www.tp-link.com and can be downloaded for free. If
TD-W8901G 54M Wireless ADSL2+ Router User Guide52the router is not experiencing difficulties, there is no need to download a more recent firmware version, unless the version has a new feature that you want to use.2) When you upgrade the router's firmware, you may lose its current configurations, so please back up the router’s current settings before you upgrade its firmware. 3) Do not turn off the router or press the Reset button while the firmware is being upgraded. 4) The router will reboot after the upgrading has been finished. To back up the Router’s current settings: Step 1: Click the ROMFILE SAVE button (shown in Figure 4-45), click Save button in the next screen (shown in Figure 4-46) to proceed. Figure 4-46 Step 2: Save the file as the appointed file (shown in Figure 4-47).Figure 4-47
TD-W8901G 54M Wireless ADSL2+ Router User Guide53To restore the Router’s settings: Step 1: Click the Browse button to locate the update file for the device, or enter the exact path in “New Romfile Location” field. Step 2: Click the UPGRADE button to complete. 4.6.4 System Restart Choose “MaintenanceėSystem Restart”, you can select to restart the device with current settings or restore to factory default settings in the screen (shown in Figure 4-48). Figure 4-48 4.6.5 DiagnosticChoose “MaintenanceėDiagnostic”, you can view the test results for the connectivity of the physical layer and protocol layer for both LAN and WAN sides in the screen (shown in Figure 4-49). Figure 4-49 4.7 HelpChoose “Help”, you can view the help information for configuration of any function.
TD-W8901G 54M Wireless ADSL2+ Router User Guide54Figure 4-50 )Note:Click the tab, and you will be able to get the corresponding information.
TD-W8901G 54M Wireless ADSL2+ Router User Guide55Appendix A: Specification GeneralStandards and Protocols ANSI T1.413, ITU G.992.1, ITU G.992.2, ITU G.992.3, ITU G.992.5 IEEE 802.11b, IEEE 802.11g ,IEEE 802.3, IEEE 802.3u, TCP/IP, PPPoA , PPPoE, SNTP, HTTP, DHCP, ICMP, NATSafety & Emission FCCǃCEPorts 4 10/100M Auto-Negotiation RJ45 port˄Auto MDI/MDIX) 1 RJ11 port LEDs 1,2,3,4(LAN), WLAN, ADSL Power, System Network Medium 10Base-T: UTP category 3, 4, 5 cable 100Base-TX: UTP category-5 Max line length: 6.5Km Transmit data-rate Max download data-rate: 24Mbps Max upload data-rate: 1Mbps System Requirement Internet Explorer 5.0 or later, Netscape Navigator 6.0 or later Win 9x/ME/2000/XP/Vista Physical and Environment Working Temperature 0ć ~ 40ćWorking Humidity 10% ~ 90% RH (non-condensing) Storage Temperature -40ć ~ 70ćStorage Humidity 5% ~ 90% RH (non-condensing)

Navigation menu