TP Link Technologies TDW8901NV1 150Mbps Wireless N ADSL2+ Modem Router User Manual TD W8901N User Guide REV2
TP-Link Technologies Co., Ltd. 150Mbps Wireless N ADSL2+ Modem Router TD W8901N User Guide REV2
TD-W8901N_User Guide_REV2
TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Rev: 1.0.0 1910010775 COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved. http://www.tp-link.com FCC STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/ TV technician for help. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference. 2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment. FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. “To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.” II CE Mark Warning This is a Class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. This device has been designed to operate with the antennas listed below, and having a maximum gain of 5dBi. Antennas not included in this list or having a gain greater than 5dBi are strictly prohibited for use with this device. The required antenna impedance is 50 ohms. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1)cet appareil ne doit pas provoquer d’interférences et (2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. Korea Warning Statements: 당해 무선설비는 운용중 전파혼신 가능성이 있음. NCC Notice: 經型式認證合格之低功率射頻電機,非經許可,公司、商號或使用者均不得擅自變更頻率、加大功 III 率或變更原設計之特性及功能。 低功率射頻電機之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並 改善至無干擾時方得繼續使用。前項合法通信,指依電信法規定作業之無線電通信。低功率射頻電 機須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。 Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам нормативних документів та вимогам, що передбачені чинними законодавчими актами України. Safety Information When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. Avoid water and wet locations. This product can be used in the following countries: AT BG BY CA CZ DE DK EE ES FI FR GB GR HU IE IT LT LV MT NL NO PL PT RO RU SE SK TR UA IV TP-LINK TECHNOLOGIES CO., LTD DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N ADSL2+ Modem Router Model No.: TD-W8901N Trademark: TP-LINK We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC, Directives 2004/108/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.2.1:2012 EN 55022:2010 EN 55024:2010 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008 EN60950-1:2006+A11:2009+A1:2010+A12:2011 EN62311:2008 The product carries the CE Mark: Person responsible for marking this declaration: Yang Hongliang Product Manager of International Business Date of issue: 2012 TP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China CONTENTS Package Contents .................................................................................................... 1 Chapter 1. Introduction......................................................................................... 2 1.1 Product Overview........................................................................................... 2 1.2 Main Features ................................................................................................ 2 1.3 Conventions ................................................................................................... 3 Chapter 2. Hardware Installation ......................................................................... 4 2.1 The Front Panel ............................................................................................. 4 2.2 The Back Panel.............................................................................................. 5 2.3 Installation Environment................................................................................. 6 2.4 Connecting the Modem Router ...................................................................... 7 Chapter 3. Quick Installation Guide..................................................................... 9 3.1 Configure PC ................................................................................................. 9 3.2 Login ............................................................................................................ 12 Chapter 4. Software Configuration .................................................................... 16 4.1 Status........................................................................................................... 16 4.1.1 4.1.2 4.1.3 Device Info ..............................................................................................................16 System Log .............................................................................................................17 Statistics..................................................................................................................18 4.2 Quick Start ................................................................................................... 20 4.3 Interface Setup............................................................................................. 21 4.3.1 4.3.2 4.3.3 Internet ....................................................................................................................21 LAN .........................................................................................................................27 Wireless ..................................................................................................................31 4.4 Advanced Setup........................................................................................... 42 4.4.1 4.4.2 4.4.3 4.4.4 4.4.5 4.4.6 Firewall....................................................................................................................42 Routing....................................................................................................................43 NAT.........................................................................................................................44 QoS.........................................................................................................................47 VLAN.......................................................................................................................50 ADSL.......................................................................................................................52 4.5 Access Management.................................................................................... 53 4.5.1 4.5.2 4.5.3 ACL .........................................................................................................................53 Filter ........................................................................................................................54 SNMP......................................................................................................................63 4.5.4 4.5.5 4.5.6 UPnP.......................................................................................................................63 DDNS......................................................................................................................64 CWMP.....................................................................................................................65 4.6 Maintenance ................................................................................................ 66 4.6.1 4.6.2 4.6.3 4.6.4 4.6.5 Administration .........................................................................................................66 Time Zone ...............................................................................................................67 Firmware .................................................................................................................68 SysRestart ..............................................................................................................71 Diagnostics .............................................................................................................71 4.7 Help.............................................................................................................. 72 Appendix A: Specifications ................................................................................... 74 Appendix B: Troubleshooting ............................................................................... 75 Appendix C: Technical Support ............................................................................ 78 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Package Contents The following contents should be found in your package: One TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router One Power Adapter for TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router Quick Installation Guide One RJ45 cable Two RJ11 cables One ADSL splitter (Optional) One Resource CD, which includes this User Guide Note: Make sure that the package contains the above items. If any of the listed items are damaged or missing, please contact your distributor. TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 1. Introduction Thank you for choosing the TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router. 1.1 Product Overview The device is designed to provide a simple and cost-effective ADSL Internet connection for a private Ethernet or IEEE 802.11n/ IEEE 802.11g/ IEEE 802.11b wireless network. The TD-W8901N connects to an Ethernet LAN or computers via standard Ethernet ports. The ADSL connection is made using ordinary telephone line with standard connectors. Multiple workstations can be networked and connected to the Internet using a single Wide Area Network (WAN) interface and single global IP address. The advanced security enhancements, IP/MAC Filter, Application Filter and URL Filter can help to protect your network from potentially devastating intrusions by malicious agents from the outside of your network. Quick Start of the Web-based Utility is supplied and friendly help messages are provided for the configuration. Network and Router management is done through the Web-based Utility which can be accessed through local Ethernet using any web browser. ADSL The TD-W8901N supports full-rate ADSL2+ connectivity conforming to the ITU and ANSI specifications. In addition to the basic DMT physical layer functions, the ADSL2+ PHY supports dual latency ADSL2+ framing (fast and interleaved) and the I.432 ATM Physical Layer. Wireless In the most attentive wireless security, the Router provides multiple protection measures. It can be set to turn off the wireless network name (SSID) broadcast so that only stations that have the SSID can be connected. The Router provides wireless LAN 64/128-bit WEP encryption security, WPA-PSK/WPA2-PSK authentication, as well as TKIP/AES encryption security. 1.2 Main Features Four 10/100Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port. Provides external splitter. Adopts Advanced DMT modulation and demodulation technology. Supports bridge mode and Router function. Multi-user sharing a high-speed Internet connection. Downstream data rates up to 24Mbps, upstream data rates up to 3.5Mbps(With Annex M enabled). TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Supports long transfers, the max line length can reach to 6.5Km. Supports remote configuration and management through SNMP and CWMP. Supports PPPoE, it allows connecting the internet on demand and disconnecting from the Internet when idle. Provides reliable ESD and surge-protect function with quick response semi-conductive surge protection circuit. High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth. Supports All ADSL industrial standards. Compatible with all mainstream DSLAM (CO). Provides integrated access of internet and route function which face to SOHO user. Real-time Configuration and device monitoring. Supports Multiple PVC (Permanent Virtual Circuit). Built-in DHCP server. Built-in firewall, supporting IP/MAC filter, Application filter and URL filter. Supports Virtual Server, DMZ host and IP Address Mapping. Supports Dynamic DNS, UPnP and Static Routing. Supports system log and flow Statistics. Supports firmware upgrade and Web management. Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security. Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List). 1.3 Conventions The Router or device mentioned in this User Guide stands for TD-W8901N without any explanations. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Chapter 2. Hardware Installation 2.1 The Front Panel Figure 2-1 The LEDs locate on the front panel. They indicate the device’s working status. For details, please refer to LED Explanation. LED Explanation: Name (Power) (ADSL) (Internet) (WLAN) (LAN 1-4) Status Indication On The modem router is powered on. Off The modem router is off. Please ensure that the power adapter is connected correctly. On ADSL line is synchronized and ready to use. Flash The ADSL negotiation is in progress. Off ADSL synchronization fails. Please refer to Note 1 for troubleshooting. On The network is available with a successful Internet connection. Flash There is data being transmitted or received via the Internet. Off There is no successful Internet connection or the modem router is operating in Bridge mode. Please refer to Note 2 for troubleshooting. On Wireless is enabled but no data is being transmitted. Flash The modem router is sending or receiving data over the wireless network. Off Wireless function is disabled. On There is a device connected to this LAN port. Flash The modem router is sending or receiving data over this LAN port. Off There is no device connected to this LAN port. Note: 1. If the ADSL LED is off, please check your Internet connection first. Refer to 2.4 Connecting the Modem Router for more information about how to make Internet connection correctly. If you have already made a right connection, please contact your ISP to make sure if your Internet service is available now. 2. If the Internet LED is off, please check your ADSL LED first. If your ADSL LED is also off, please refer to Note 1. If your ADSL LED is GREEN ON, please check your Internet configuration. You may need to check this part of information with your ISP and make sure TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide everything have been input correctly. Refer to 4.1.1 Device Info and 4.3.1 Internet for more information. 2.2 The Back Panel Figure 2-2 POWER: The Power plug is where you will connect the power adapter. ON/OFF: The switch for the power. WiFi: Press this button to enable or disable Wireless LAN interface. RESET: There are two ways to reset the Router's factory defaults. Method one: With the Router powered on, use a pin to press and hold the Reset button for at least 5 seconds. And the Router will reboot to its factory default settings. Method two: Restore the default setting from “Maintenance-SysRestart” of the Router's Web-based Utility. 1, 2, 3, 4 (LAN): Through the port, you can connect the Router to your PC or the other Ethernet network devices. TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide ADSL: Through the port, you can connect the router with the telephone. Or you can connect them by an external separate splitter. For details, please refer to 2.4 Connecting the Modem Router. 2.3 Antenna: Used for wireless operation and data transmit. Installation Environment The Product should not be located where it will be exposed to moisture or excessive heat. Place the Router in a location where it can be connected to the various devices as well as to a power source. Make sure the cables and power cord are safely placed out of the way so they do not create a tripping hazard. The Router can be placed on a shelf or desktop. Keep away from the strong electromagnetic radiation and the device of electromagnetic sensitive. Figure 2-3 Wall-mount Install Note: The diameter of the screw, 3.5mmNetwork”. Select Airport on the left menu bar, and then click Advanced for wireless configuration; or select Ethernet for wired configuration. In the Con-figure IPv4 box under TCP/IP, select Using DHCP. Click Apply to save the settings. For Windows 7 Click “Start -> Control Panel -> Network and Internet -> View network status -> Change adapter settings”. Right-click Wireless Network Connection (or Local Area Connection), and then click Properties. Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. 75 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide For Windows XP Click “Start -> Control Panel -> Network and Internet Connections -> Network Connections”. Right-click Wireless Network Connection (or Local Area Connection), and then click Properties. Select Internet Protocol (TCP/IP), and then click Properties. Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. For Windows 8 Move your mouse to the lower right corner and click the Search icon in the Popups. Go to Apps, type Control Panel in the search box and press Enter. Go to “Control Panel -> View network status and tasks > Change settings”. adapter Right-click Ethernet, select Properties. Then double-click Internet Protocol Version 4 (TCP/IPv4). Select Obtain an IP address automatically and Obtain DNS server address automatically. Then click OK. 2) Configure your IE browser Open your IE browser, click Tools tab and you will see the following screen. Click Internet Options 76 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Select Never dial a connection Click OK Now, try to log on to the Web-based configuration page again after the above settings have been configured. If you still cannot access the configuration page, please restore your modem router’s factory default settings and reconfigure your modem router following the instructions in 3.2 Login. Please feel free to contact our Technical Support if the problem still exists. T4. What can I do if I cannot access the Internet? 1) Check to see if all the connectors are connected well, including the telephone line, Ethernet cables and power adapter. 2) Check to see if you can log on to the web management page of the modem router. If you can, try the following steps. If you cannot, please set your computer referring to T3 then try to see if you can access the Internet. If the problem persists, please go to the next step. 3) Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and password are correct. If there are any mistakes, please correct the settings and try again. 4) If you still cannot access the Internet, please restore your modem router to its factory default settings and reconfigure your modem router by following the instructions in 3.2 Login. 5) Please feel free to contact our Technical Support if the problem still exists. Note: For more details about Troubleshooting and Technical Support contact information, please log on to our Technical Support Website: http://www.tp-link.com/en/support 77 TD-W8901N 150Mbps Wireless N ADSL2+ Modem Router User Guide Appendix C: Technical Support Technical Support For more troubleshooting help, go to: http://www.tp-link.com/en/support/faq To download the latest Firmware, Driver, Utility and User Guide, go to: http://www.tp-link.com/en/support/download For all other technical support, please contact us by using the following details: Global Tel: +86 755 26504400 E-mail: support@tp-link.com Service time: 24hrs, 7 days a week UK Tel: +44 (0) 845 147 0017 E-mail: support.uk@tp-link.com Service time: 24hrs, 7 days a week Turkey Tel: 444 19 25 (Turkish Service) E-mail: support.tr@tp-link.com Service time: 9:00 AM to 9:00 PM 7 days a week Ukraine Tel: 0-800-505-508 E-mail: support.ua@tp-link.com Service time: Monday to Friday, 10:00 AM to 22:00 PM Brazil Toll Free: 0800-770-4337 (Portuguese Service) E-mail: suporte.br@tp-link.com Service time: Monday to Saturday, 08:00 AM to 08:00 PM France Tel: +33 (0) 820 800 860 (French service) Email: support.fr@tp-link.com Fee: 0.118 EUR/min from France Service time: Monday to Friday, 9:00 AM to 6:00 PM (Except French Bank holidays) Russian Federation Tel: 8 (499) 754-55-60 8 (800) 250-55-60 (toll-free call from any RF region) E-mail: support.ru@tp-link.com Service time: From 10:00 to 18:00 (Moscow time) *Except weekends and holidays in Russian Federation Switzerland Tel: +41 (0) 848 800998 (German Service) E-mail: support.ch@tp-link.com Fee: 4-8 Rp/min, depending on rate of different time Service time: Monday to Friday, 9:00 AM to 6:00 PM. GMT+ 1 or GMT+ 2 (Daylight Saving Time) Singapore Tel: +65 62840493 E-mail: support.sg@tp-link.com Service time: 24hrs, 7 days a week USA/Canada Toll Free: +1 866 225 8139 E-mail: support.usa@tp-link.com Service time: 24hrs, 7 days a week Australia/New Zealand Tel: AU 1300 87 5465 NZ 0800 87 5465 E-mail: support.au@tp-link.com (Australia) support.nz@tp-link.com (New Zealand) Service time: 24hrs, 7 days a week Italy Tel: +39 0230519020 E-mail: support.it@tp-link.com Service time: Monday to Friday, 9:00 AM to1:00PM, 2:00PM to 6:00 PM Indonesia Tel: (+62) 021 6259 135 E-mail : support.id@tp-link.com Service time : Monday to Friday, 9:00 -12:00; 13:00 -18:00 *Except public holidays Malaysia Tel: 1300 88 875465 (1300 88TPLINK) Email: support.my@tp-link.com Service time: 24hrs, 7 days a week Poland Tel: +48 (0) 801 080 618 / +48 22 7217563 (if calls from mobile phone) E-mail: support.pl@tp-link.com Service time: Monday to Friday, 9:00 AM to 5:00 PM. GMT+1 or GMT+2 (Daylight Saving Time) Germany/Austria Tel: +49 1805 875465 (German Service) +49 1805 TPLINK E-mail: support.de@tp-link.com Fee: 0.14 EUR/min from the German fixed phone network and up to 0.42 EUR/min from mobile phone Service time: Monday to Friday, 9:00 AM to 6:00 PM. GMT+ 1 or GMT+ 2 (Daylight Saving Time in Germany) *Except bank holidays in Hesse 78
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Tagged PDF : Yes XMP Toolkit : Adobe XMP Core 5.0-c060 61.134777, 2010/02/12-17:32:00 Create Date : 2012:12:04 16:50:57+08:00 Creator Tool : Acrobat PDFMaker 10.1 Word 版 Modify Date : 2013:05:20 10:40:08+08:00 Metadata Date : 2013:05:20 10:40:08+08:00 Thumbnail Width : 156 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 8472 bytes, use -b option to extract) Producer : Acrobat Distiller 10.1.0 (Windows) Keywords : Format : application/pdf Creator : Title : Description : Document ID : uuid:c3574575-e97e-463f-b751-a0cefcbacc37 Instance ID : uuid:26195de3-968d-4fc6-93ba-2c20dedf1c46 Rendition Class : proof:pdf Subject : 876 Company : Comments : Source Modified : D:20121204084945 N Pages : 1 Has Visible Transparency : False Has Visible Overprint : False Max Page Size W : 8.266941 Max Page Size H : 11.694444 Max Page Size Unit : Inches Font Name : ArialMT, Arial-BoldMT, Wingdings-Regular Font Family : Arial, Arial, Wingdings Font Face : Regular, Bold, Regular Font Type : Open Type, Open Type, Open Type Font Version : Version 3.00, Version 3.00, Version 2.55 Font Composite : False, False, False Font File Name : ARIAL.TTF, ARIALBD.TTF, WINGDING.TTF Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Group Name : 默认色板组 Swatch Groups Group Type : 0 Page Layout : OneColumn Page Mode : UseOutlines Page Count : 86 Author :EXIF Metadata provided by EXIF.tools