TP Link Technologies TDW9980V1 N600 Wireless Dual Band Gigabit VDSL2 Modem Router User Manual

Download:
Mirror Download [FCC.gov]
Document ID	2340883
Application ID	fKEE3VEfnl/EHx4DGwEJQg==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	201.42kB (2517713 bits)
Date Submitted	2014-07-31 00:00:00
Date Available	2014-07-31 00:00:00
Creation Date	2014-07-28 13:54:27
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2014-07-28 16:36:27
Document Title	Users Manual
Document Creator	Acrobat PDFMaker 11 Word 版

TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem
Router (Annex B)
COPYRIGHT & TRADEMARKS
is a registered trademark of
Specifications are subject to change without notice.
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or
registered trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2014 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1)
This device may not cause harmful interference.
2)
This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
Note: The manufacturer is not responsible for any radio or tv interference caused by unauthorized
modifications to this equipment. Such modifications could void the user’s authority to operate the
equipment.
FCC RF Radiation Exposure Statement
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. This device and its antenna must not be co-located or operating in conjunction with
any other antenna or transmitter.
“To comply with FCC RF exposure compliance requirements, this grant is applicable to only
Mobile Configurations. The antennas used for this transmitter must be installed to provide a
separation distance of at least 22 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter.”
Operations in the 5.15-5.25GHz band are restricted to indoor usage only.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in
which case the user may be required to take adequate measures.
National Restrictions
This device is intended for home and office use in all EU countries (and other countries following
the EU directive 1999/5/EC) without any limitation except for the countries mentioned below:
Country
Restriction
Reason/remark
Bulgaria
None
General authorization required for outdoor use and
public service
France
Outdoor use limited to 10
mW e.i.r.p. within the band
2454-2483.5 MHz
Military Radiolocation use. Refarming of the 2.4 GHz
band has been ongoing in recent years to allow current
relaxed regulation. Full implementation planned 2012
Italy
None
If used outside of own premises, general authorization is
required
Luxembourg
None
General authorization required for network and service
supply(not for spectrum)
Norway
Implemented
This subsection does not apply for the geographical area
within a radius of 20 km from the centre of Ny-Ålesund
Russian Federation
None
Only for indoor applications
Note: Please don’t use the product outdoors in France.
Canadian Compliance Statement
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1)This device may not cause interference, and
(2)This device must accept any interference, including interference that may cause undesired
operation of the device.
Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le
fonctionnement est soumis aux deux conditions suivantes:
(1)cet appareil ne doit pas provoquer d’interférences et
(2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un
fonctionnement non souhaité de l’appareil.
This device has been designed to operate with the antennas listed below, and having a maximum
gain of 5 dBi. Antennas not included in this list or having a gain greater than 5 dBi are strictly
prohibited for use with this device. The required antenna impedance is 50 ohms.
To reduce potential radio interference to other users, the antenna type and its gain should be so
chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for
successful communication.
Industry Canada Statement
Complies with the Canadian ICES-003 Class B specifications.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This device complies with RSS 210 of Industry Canada. This Class B device meets all the
requirements of the Canadian interference-causing equipment regulations.
Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le
matériel brouilleur du Canada.
Korea Warning Statements:
당해 무선설비는 운용중 전파혼신 가능성이 있음.
NCC Notice& BSMI Notice:
注意！
依據 低功率電波輻射性電機管理辦法
第十二條 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻率、
加大功率或變更原設計之特性或功能。
第十四條 低功率射頻電機之使用不得影響飛航安全及干擾合法通行；經發現有干擾現象時，應立即
停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信規定作業之無線電信。低功率射
頻電機需忍受合法通信或工業、科學以及醫療用電波輻射性電機設備之干擾。
減少電磁波影響，請妥適使用。
安全諮詢及注意事項
●請使用原裝電源供應器或只能按照本產品注明的電源類型使用本產品。
●清潔本產品之前請先拔掉電源線。請勿使用液體、噴霧清潔劑或濕布進行清潔。
●注意防潮，請勿將水或其他液體潑灑到本產品上。 
●插槽與開口供通風使用，以確保本產品的操作可靠並防止過熱，請勿堵塞或覆蓋開口。
●請勿將本產品置放於靠近熱源的地方。除非有正常的通風，否則不可放在密閉位置中。
●請不要私自打開機殼，不要嘗試自行維修本產品，請由授權的專業人士進行此項工作。
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами
України.
Safety Information



When product has power button, the power button is one of the way to shut off the product;
when there is no power button, the only way to completely shut off power is to disconnect the
product or the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock
and voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
This product can be used in the following countries:
AT
BG
BY
CA
CZ
DE
DK
EE
ES
FI
FR
GB
GR
HU
IE
IT
LT
LV
MT
NL
NO
PL
PT
RO
RU
SE
SK
TR
UA
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B)
Model No.: TD-W9980B
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical
regulations applicable to the product within the scope of Council Directives:
Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC,
Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents
EN 300 328 V1.8.1
EN 301 489-1 V1.9.2 & EN 301 489-17 V2.2.1
EN 55022: 2010 + AC: 2011
EN 55024: 2010
EN 61000-3-2: 2006 + A1: 2009 + A2: 2009
EN 61000-3-3: 2013
EN 60950-1: 2006 + A11: 2009 + A1: 2010 + A12: 2011
EN 50385: 2002
EN 301 893 V1.7.1
The product carries the CE Mark:
Person responsible for making this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2014
TP-LINK TECHNOLOGIES CO., LTD
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park,
Shennan Rd, Nanshan, Shenzhen, China
CONTENTS
Package Contents .................................................................................................... 1
Chapter 1. Product Overview ................................................................................... 2
1.1 Overview of the Modem Router..................................................................................... 2
1.2 Main Features ............................................................................................................... 3
1.3 Panel Layout ................................................................................................................. 4
1.3.1 The Front Panel ................................................................................................................... 4
1.3.2 The Back Panel .................................................................................................................... 6
Chapter 2. Connecting the Modem Router ............................................................. 7
2.1 System Requirements ................................................................................................... 7
2.2 Installation Environment Requirements ......................................................................... 7
2.3 Connecting the Modem Router ..................................................................................... 8
Chapter 3. Quick Installation Guide ........................................................................ 9
3.1 TCP/IP Configuration .................................................................................................... 9
3.2 Quick Installation Guide .............................................................................................. 10
Chapter 4. Configuring the Modem Router .......................................................... 16
4.1 Login ........................................................................................................................... 16
4.2 Status ......................................................................................................................... 16
4.3 Quick Setup ................................................................................................................ 17
4.4 Operation Mode .......................................................................................................... 18
4.5 Network ...................................................................................................................... 18
4.5.1 WAN Settings ..................................................................................................................... 19
4.5.2 Interface Grouping ............................................................................................................. 34
4.5.3 LAN Settings ...................................................................................................................... 35
4.5.4 IPv6 LAN Settings .............................................................................................................. 37
4.5.5 MAC Clone ......................................................................................................................... 38
4.5.6 ALG Settings ...................................................................................................................... 39
4.5.7 DSL Settings ...................................................................................................................... 40
4.5.8 IPSec VPN ......................................................................................................................... 40
4.6 DHCP Server .............................................................................................................. 43
4.6.1 DHCP Settings ................................................................................................................... 44
4.6.2 Clients List.......................................................................................................................... 45
4.6.3 Address Reservation .......................................................................................................... 45
4.6.4 Conditional Pool ................................................................................................................. 46
4.7 Dual Band Selection ................................................................................................... 47
4.8 Wireless 2.4GHz ......................................................................................................... 48
4.8.1 Basic Settings .................................................................................................................... 48
4.8.2 WPS Settings ..................................................................................................................... 50
4.8.3 Wireless Security ............................................................................................................... 52
4.8.4 Wireless MAC Filtering ...................................................................................................... 55
4.8.5 Wireless Advanced ............................................................................................................ 56
4.8.6 Wireless Status .................................................................................................................. 58
4.9 Wireless 5GHz ............................................................................................................ 58
4.9.1 Basic Settings .................................................................................................................... 58
4.9.2 WPS Settings ..................................................................................................................... 60
4.9.3 Wireless Security ............................................................................................................... 62
4.9.4 Wireless MAC Filtering ...................................................................................................... 64
4.9.5 Wireless Advanced ............................................................................................................ 65
4.9.6 Wireless Status .................................................................................................................. 66
4.10 Guest Network ............................................................................................................ 67
4.10.1 Basic Settings ................................................................................................................... 67
4.10.2 Guest Network Status ....................................................................................................... 69
4.11 USB Settings .............................................................................................................. 69
4.11.1 USB Mass Storage ........................................................................................................... 69
4.11.2 User Accounts .................................................................................................................. 70
4.11.3 Storage Sharing ................................................................................................................ 71
4.11.4 FTP Server ....................................................................................................................... 73
4.11.5 Media Server .................................................................................................................... 74
4.11.6 Print Server ....................................................................................................................... 75
4.12 Route Settings ............................................................................................................ 76
4.12.1 Default Gateway ............................................................................................................... 76
4.12.2 Static Route ...................................................................................................................... 76
4.12.3 IPv6 Static Route .............................................................................................................. 77
4.12.4 RIP Settings ...................................................................................................................... 78
4.13 Forwarding .................................................................................................................. 79
4.13.1 Virtual Servers .................................................................................................................. 79
4.13.2 Port Triggering .................................................................................................................. 80
4.13.3 DMZ .................................................................................................................................. 82
4.13.4 UPnP ................................................................................................................................ 83
4.14 Parental Control .......................................................................................................... 84
4.15 IPv4 Firewall ............................................................................................................... 85
4.15.1 Rule .................................................................................................................................. 85
4.15.2 LAN Host .......................................................................................................................... 86
4.15.3 WAN Host ......................................................................................................................... 87
4.15.4 Schedule ........................................................................................................................... 88
4.16 IPv6 Firewall ............................................................................................................... 89
4.16.1 IPv6 Rule .......................................................................................................................... 90
4.16.2 IPv6 LAN Host .................................................................................................................. 91
4.16.3 IPv6 WAN Host ................................................................................................................. 92
4.16.4 IPv6 Schedule................................................................................................................... 92
4.17 IPv6 Tunnel................................................................................................................. 93
4.18 Bandwidth Control....................................................................................................... 96
4.19 IP&MAC Binding ......................................................................................................... 97
4.19.1 Binding Settings ................................................................................................................ 97
4.19.2 ARP List ............................................................................................................................ 98
4.20 Dynamic DNS ............................................................................................................. 99
4.21 Diagnostic ................................................................................................................... 99
4.22 System Tools ............................................................................................................ 100
4.22.1 System Log ..................................................................................................................... 100
4.22.2 Time Settings .................................................................................................................. 101
4.22.3 Manage Control .............................................................................................................. 102
4.22.4 CWMP Settings .............................................................................................................. 103
4.22.5 SNMP Settings ............................................................................................................... 104
4.22.6 Backup & Restore ........................................................................................................... 104
4.22.7 Factory Defaults.............................................................................................................. 105
4.22.8 Firmware Upgrade .......................................................................................................... 105
4.22.9 Reboot ............................................................................................................................ 106
4.22.10 Statistics ...................................................................................................................... 107
4.23 Logout....................................................................................................................... 108
Appendix A: Specifications ................................................................................. 109
Appendix B: Troubleshooting ............................................................................. 110
Appendix C: Technical Support .......................................................................... 113
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Package Contents
The following contents should be found in your package:

One TD-W9980B N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B)

One Power Adapter for TD-W9980B N600 Wireless Dual Band Gigabit VDSL2 Modem Router
(Annex B)

Quick Installation Guide

One RJ45 cable

Two RJ11 cables

One VDSL splitter

One Resource CD for TD-W9980B N600 Wireless Dual Band Gigabit VDSL2 Modem Router
(Annex B), including:
•
This User Guide
•
Other Helpful Information
 Note:
Make sure that the package contains the above items. If any of the listed items are damaged or
missing, please contact your distributor.
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Chapter 1. Product Overview
Thank you for choosing the TD-W9980B N600 Wireless Dual Band Gigabit VDSL2 Modem
Router (Annex B).
1.1 Overview of the Modem Router
The TD-W9980B N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) integrates
4-port Switch, Firewall, NAT-Router and Wireless AP. The Modem Router delivers exceptional
range and speed, which can fully meet the need of Small Office/Home Office (SOHO) networks
and the users demanding higher networking performance.
The TD-W9980B N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) utilizes
integrated VDSL2 transceiver and high speed MIPS CPU. The modem router supports full-rate
VDSL2 connectivity conforming to the ITU and ANSI specifications.
In addition to the basic DMT physical layer functions, the VDSL2 PHY supports dual latency
VDSL2 framing (fast and interleaved) and the I.432 ATM Physical Layer.
The modem router provides up to 300Mbps (2.4GHz) + 300Mbps (5GHz) wireless connection with
other 802.11n wireless clients. The incredible speed makes it ideal for handling multiple data streams
at the same time, which ensures your network stable and smooth. The performance of this 802.11n
wireless Router will give you the unexpected networking experience at speed much faster than
802.11g. It is also compatible with all IEEE 802.11g and IEEE 802.11b products.
With multiple protection measures, including SSID broadcast control and wireless LAN 64/128
WEP encryption, Wi-Fi protected Access (WPA2-PSK, WPA-PSK), as well as advanced Firewall
protections, the TD-W9980B N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B)
provides complete data privacy.
The modem router provides flexible access control, so that parents or network administrators can
establish restricted access policies for children or staff. It also supports Virtual Server and DMZ
host for Port Triggering, and then the network administrators can manage and monitor the network
in real time with the remote management function.
Since the modem router is compatible with virtually all the major operating systems, it is very easy
to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in
this user guide. Before installing the modem router, please look through this guide to know all the
modem router’s functions.
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
1.2 Main Features

Complies with IEEE 802.11n to provide a wireless data rate of up to 300Mbps (2.4GHz) +
300Mbps (5GHz).

Four 10/100/1000Mbps Auto-Negotiation RJ45 LAN ports (Auto MDI/MDIX), one RJ11 port.

Provides external splitter.

Adopts Advanced DMT modulation and demodulation technology.

Supports bridge mode and Router function.

Multi-user sharing a high-speed Internet connection.

Downstream data rates up to 100Mbps, upstream data rates up to 100Mbps.

Supports long transfers, the max line length can reach to 6.5Km.

Supports remote configuration and management through SNMP and CWMP.

Supports PPPoE, it allows connecting the internet on demand and disconnecting from the
Internet when idle.

Provides reliable ESD and surge-protect function with quick response semi-conductive surge
protection circuit.

High speed and asymmetrical data transmit mode, provides safe and exclusive bandwidth.

Compatible with all mainstreams DSLAM (CO).

Provides integrated access of internet and route function which face to SOHO user.

Real-time Configuration and device monitoring.

Supports Multiple PVC (Permanent Virtual Circuit).

Built-in DHCP server.

Built-in firewall, supporting IP/MAC filter and URL filter.

Supports Virtual Server, DMZ host and Port Triggering.

Supports Dynamic DNS, UPnP and Static Routing.

Supports system log and flow Statistics.

Supports firmware upgrade and Web-Management page.

Provides WPA-PSK/WPA2-PSK data security, TKIP/AES encryption security.

Provides 64/128-bit WEP encryption security and wireless LAN ACL (Access Control List).

Supports USB Storage Sharing, Print Server, FTP Server, Media Server.

Supports Ethernet WAN (EWAN).

Supports Bandwidth Control.

Supports IPv6.

Supports VDSL.
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
1.3 Panel Layout
1.3.1 The Front Panel
Figure 1-1
The modem router’s LEDs are located on the front panel (View from left to right). They indicate the
device’s working status. For details, please refer to LED Explanation.
LED Explanation:
Name
Status
On
The modem router is powered on.
Off
The modem router is off. Please ensure that the power adapter is
connected correctly.
On
DSL line is synchronized and ready to use.
(Power)
(DSL)
Indication
Flash
The DSL negotiation is in progress.
Off
DSL synchronization fails. Please refer to Note 1 for
troubleshooting.
On
The network is available with a successful Internet connection.
Flash
There is data being transmitted or received via the Internet.
(Internet)
Off
There is no successful Internet connection or the modem router
is operating in Bridge mode. Please refer to Note 2 for
troubleshooting.
TD-W9980B
(Wireless
2.4GHz)
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Flash
Off
(Wireless
5GHz)
(WPS)
Flash
(USB on the
back panel)
Wireless is disabled.
Wireless is enabled. The modem router is working on 5GHz
radio band.
Off
Wireless is disabled.
On
A wireless device has been successfully added to the network by
WPS function.
Slow Flash
WPS handshaking is in process and will continue for about 2
minutes. Please press the WPS button on other wireless devices
that you want to add to the network while the LED is flashing.
Quick
Flash
A wireless device has failed to be added to the network by WPS
function. Please refer to 4.8.2 WPS Settings for more
information.
On
(LAN1-4)
Wireless is enabled. The modem router is working on 2.4GHz
radio band.
Flash
There is a device connected to this LAN port.
The modem router is sending or receiving data over this LAN
port.
Off
There is no device connected to this LAN port.
On
A storage device or printer has connected to the USB port.
Flash
Off
There is data being transmitted or received via the USB port.
No storage device or printer is plugged into the USB port.
 Note:
1. If the DSL LED is off, please check your Internet connection first. Refer to 2.3 Connecting the
Modem Router for more information about how to make Internet connection correctly. If you
have already made a right connection, please contact your ISP to make sure if your Internet
service is available now.
2. If the Internet LED is off, please check your DSL LED first. If your DSL LED is also off, please
refer to Note 1. If your DSL LED is GREEN ON, please check your Internet configuration. You
may need to check this part of information with your ISP and make sure everything have been
input correctly.
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
1.3.2 The Back Panel
Figure 1-2

VDSL: Through the port, you can connect the modem router with the telephone. Or you can
connect them by an external separate splitter. For details, please refer to 2.3 Connecting the
Modem Router.

USB1, USB2: The USB port connects to a USB storage device or a USB printer.

WPS: The switch for the WPS function. For details, please refer to 4.8.2 WPS Settings.

RESET: There are two ways to reset the modem router's factory defaults.
Method one: With the modem router powered on, use a pin to press and hold the Reset
button for at least 5 seconds. And the modem router will reboot to its factory default settings.
Method two: Restore the default setting from 4.22.7 Factory Defaults of the modem router's
Web-based management page.

WiFi: The switch for the WiFi function. Move it to left /right to enable/disable the WiFi function.

LAN4/WAN, LAN3, LAN2, LAN1: Through these ports, you can connect the modem router to
your PC or the other Ethernet network devices. In wireless router mode you will be able to
connect to Cable/FTTH/VDSL/ADSL device.

ON/OFF: The switch for the power.

POWER: The Power plug is where you will connect the power adapter.

Antennas: Used for wireless operation and data transmit.
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Chapter 2. Connecting the Modem Router
2.1 System Requirements
 Broadband Internet Access Service (DSL/Cable/Ethernet).
 PCs with a working Ethernet Adapter and an Ethernet cable with RJ45 connectors.
 TCP/IP protocol on each PC.
 Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari.
2.2 Installation Environment Requirements





The Product should not be located where it will be exposed to moisture or excessive heat.
Place the modem router in a location where it can be connected to the various devices as well
as to a power source.
Make sure the cables and power cord are safely placed out of the way so they do not create a
tripping hazard.
The modem router can be placed on a shelf or desktop.
Keep away from the strong electromagnetic radiation and the device of electromagnetic
sensitive.
Generally, TD-W9980B is placed on a horizontal surface. The device also can be mounted on the wall
as shown in Figure 2-1.
Figure 2-1 Wall-mount install
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
 Note:
The diameter of the screw, 3.5mm Manage Control page to be any other value except 80 such as 8080.
Otherwise there will be a conflict to disable the virtual server.
4.13.2 Port Triggering
Choose menu “Forwarding”→ ”Port Triggering”, you can view and add port triggering in the
next screen (shown in Figure 4-74). Some applications require multiple connections, like Internet
80
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
games, video conferencing, Internet telephoning and so on. Port Triggering is used for some of
these applications that cannot work with a pure NAT modem router.
Figure 4-74
To add a new rule, follow the steps below.
1.
Click the Add New button, the next screen will pop-up as shown in Figure 4-75.
2.
Select a common application from the Common Service Port drop-down list, then the
Trigger Port field and the Open Ports field will be automatically filled. If the Common
Service Port does not have the application you need, enter the Trigger Port and the Open
Ports manually.
3.
Select the protocol used for Trigger Port from the Trigger Protocol drop-down list, either
TCP, UDP, or All.
4.
Select the protocol used for Incoming Ports from the Open Protocol drop-down list, either
TCP or UDP, or All.
5.
Select Enable in Status field.
6.
Click the Save button to save the new rule.
Figure 4-75

Interface: Display the default gateway you have ser in 4.5.1 WAN Settings.

Trigger Port: The port for outgoing traffic. An outgoing connection using this port will trigger
this rule.

Trigger Protocol: The protocol used for Trigger Ports, either TCP, UDP, or All (all protocols
supported by the modem router).
81
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide

Open Port: The port or port range used by the remote system when it responds to the
outgoing request. A response using one of these ports will be forwarded to the PC which
triggered this rule. You can input at most 5 groups of ports (or port sections). Every group of
ports must be separated with ",", for example, 2000-2038, 2046, 2050-2051, 2085,
3010-3030.

Open Protocol: The protocol used for Incoming Port, either TCP, UDP, or ALL (all
protocols supported by the modem router).

Status: The status of this entry, Enabled means the Port Triggering entry is enabled.

Common Service Port: Some popular applications already listed in the drop-down list of
Open Protocol.
To modify or delete an existing entry:
1.
Find the desired entry in the table.
2.
Click Edit as desired on the Edit column.
Click the Enable/ Disabled Selected button to make selected entries enabled/ disabled.
Click the Delete Selected button to delete selected entries.
Once the modem router is configured, the operation is as follows:
1.
A local host makes an outgoing connection to an external host using a destination port
number defined in the Trigger Port field.
2.
The modem router records this connection, opens the incoming port or ports associated with
this entry in the Port Triggering table, and associates them with the local host.
3.
When necessary, the external host will be able to connect to the local host using one of the
ports defined in the Incoming Ports field.
 Note:
1.
2.
3.
When the trigger connection is released, the corresponding opened ports will be closed.
Each rule can only be used by one host on the LAN at a time. The trigger connection of other
hosts on the LAN will be refused.
Open Ports ranges cannot overlap each other.
4.13.3 DMZ
Choose menu “Forwarding→DMZ”, and then you can view and configure DMZ host in the screen
(shown in Figure 4-76).The DMZ host feature allows one local host to be exposed to the Internet
for a special-purpose service such as Internet gaming or videoconferencing. The modem router
forwards packets of all services to the DMZ host. Any PC whose port is being forwarded must
have its DHCP client function disabled and should have a new static IP Address assigned to it
because its IP Address may be changed when using the DHCP function.
82
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Figure 4-76
To assign a computer or server to be a DMZ server:
1.
Click the Enable button.
2.
Enter the IP address of a local PC that is set to be DMZ host in the DMZ Host IP Address
field.
3.
Click the Save button.
4.13.4 UPnP
Choose menu “Forwarding→UPnP”, and then you can view the information about UPnP in the
screen (shown in Figure 4-77). The Universal Plug and Play (UPnP) feature allows the devices,
such as Internet computers, to access the local host resources or devices as needed. UPnP
devices can be automatically discovered by the UPnP service application on the LAN.
Figure 4-77

Current UPnP Status: UPnP can be enabled or disabled by clicking the Enable or Disable
button. This feature is enabled by default.

Current UPnP Settings List: This table displays the current UPnP information.
•
App Description: The description about the application which initiates the UPnP
request.
•
External Port: The port which the modem router opens for the application.
•
Protocol: The type of protocol which is opened.
•
Internal Port: The port which the modem router opened for local host.
•
IP Address: The IP address of the local host which initiates the UPnP request.
•
Status: Either Enabled or Disabled. "Enabled" means that the port is still active;
otherwise, the port is inactive.
Click the Enable button to enable UPnP.
83
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Click the Disable button to disable UPnP.
Click the Refresh button to update the Current UPnP Settings List.
4.14 Parental Control
Choose menu “Parental Control”, and you can configure the parental control in the screen as
shown in Figure 4-78. The Parental Control function can be used to control the Internet activities of
the child, limit the child to access certain websites and restrict the time of surfing.
Figure 4-78

Enable Parental Control: Check the box if you want this function to take effect. This function
is disabled by default.

MAC Address of Parental PC: In this field, enter the MAC address of the controlling PC, or
you can make use of the Copy To Above button below.

MAC Address of Current PC: This field displays the MAC address of the PC that is
managing this modem router. If the MAC Address of your adapter is registered, you can click
the Copy To Above button to fill this address to the MAC Address of Parental PC field above.

Add URL: Here you can input the net addresses which the child is allowed to access.
Click the Save button to save your settings.
84
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
4.15 IPv4 Firewall
There are four submenus under the Firewall menu: Rule, LAN Host, WAN Host and Schedule.
Click any of them, and you will be able to configure the corresponding function.
4.15.1 Rule
Choose menu “Firewall” → “Rule”, and then you can view and set Access Control rules in the
screen as shown in Figure 4-79.
Figure 4-79
 Enable Firewall: Select the check box to enable the Firewalll function, so the Default Filtering
Rules can take effect.
 Description: Here displays the description of the rule and this name is unique.
 LAN Host: Here displays the host selected in the corresponding rule.
 Target: Here displays the target selected in the corresponding rule.
 Schedule: Here displays the schedule selected in the corresponding rule.
 Status: Here displays the status of the rule, enabled or not.
 Edit: Here you can edit or delete an existing rule.
 Add New: Click the Add New button to add a new rule entry.
 Enable Selected: Click the Enable Selected button to enable the selected rules in the list.
 Disable Selected: Click the Disable Selected button to disable the selected rules in the list.
 Delete Selected: Click the Delete Selected button to delete the selected entries in the table.
85
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
The methods to add a new rule:
1.
Click the Add New button and the next screen will pop up as shown in Figure 4-80.
2.
Give a name (e.g. Rule_1) for the rule in the Description field.
3.
Select a host from the LAN Host drop-down list or choose “Add LAN Host”.
4.
Select a target from the WAN Host drop-sown list or choose “Add WAN Host”.
5.
Select a schedule from the Schedule drop-down list or choose “Add Schedule”.
6.
In the Action field, select Deny or Allow to deny or allow your entry.
7.
In the Status field, select Enabled or Disabled to enable or disable your entry.
8.
In the Direction field, select IN or OUT from the drop-down list for the direction.
9.
In the Protocol field, here are four options, All, TCP, UDP, and ICMP. Select one of them
from the drop-down list for the target.
10. Click the Save button.
Figure 4-80
4.15.2 LAN Host
Choose menu “Firewall” → “LAN Host”, and then you can view and set a Host list in the screen
as shown in Figure 4-81.
Figure 4-81

Description: Here displays the description of the host and this description is unique.

Address Info: Here displays the information about the host. It can be IP or MAC.

Edit: To modify an existing entry.
86
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
To add a new entry, please follow the steps below.
1.
Click the Add New button.
2.
In the Mode field, select IP Address or MAC Address.

If you select IP Address, please follow the steps below:
1) In Description field, create a unique description for the host (e.g. Host_1).
2) In IP Address field, enter the IP address.

If you select MAC Address, please follow the steps below:
1) In Description field, create a unique description for the host (e.g. Host_1).
2) In MAC Address field, enter the MAC address.
3.
Click the Save button to complete the settings.
Click the Delete Selected button to delete the selected entries in the table.
4.15.3 WAN Host
Choose menu “Firewall” → “WAN Host”, and then you can view and set a Host list in the screen
as shown in Figure 4-82.
Figure 4-82
 Description: Here displays the description about the WAN and this description is unique.
 Details: The details can be IP address, port, or domain name.
 Edit: To modify an existing entry.
To add a new entry, please follow the steps below.
1.
Click the Add New button.
2.
In Mode field, select IP Address, MAC Address or URL Address.
If you select IP Address, the screen shown is Figure 4-83.
Figure 4-83
1)
In Description field, create a unique description for the host (e.g. Host_1).
87
TD-W9980B
2)
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
In IP Address field, enter the IP address.
If you select MAC Address, the screen shown is Figure 4-84.
Figure 4-84
1)
In Description field, create a unique description for the host (e.g. Host_1).
2)
In MAC Address field, enter the MAC address.
If you select URL Address, the screen shown is Figure 4-85.
Figure 4-85
1)
In Description field, create a unique description for the host (e.g. Host_1).
2)
Enter the URL address in the Add URL Address field, and then click the Add button. The
URL address will be shown in the Detail table. If you click the Delete button, the existing URL
address in the Detail table can be deleted.
3.
Click the Save button to complete the settings.
4.15.4 Schedule
Choose menu “Firewall” → “Schedule”, and then you can view and set a Schedule list in the
next screen as shown in Figure 4-86.
Figure 4-86

Description: Here displays the description of the schedule and this description is unique.
88
TD-W9980B

N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Edit: Here you can modify an existing schedule.
To add a new schedule, follow the steps below:
1. Click Add New button and the next screen will pop-up as shown in Figure 4-87.
2. In Description field, create a unique description for the schedule (e.g. Schedule_1).
3. In Apply To field, select the day or days you need.
4. In time field, you can select all day-24 hours or you may enter the Start Time and Stop Time
in the corresponding field.
5. Click Save to complete the settings.
Click the Clear Schedule button to clear your settings in the table.
Figure 4-87
Click the Delete Selected button to delete the slected entries in the table.
4.16 IPv6 Firewall
There are four submenus under the IPv6 Firewall menu: IPv6 Rule, IPv6 LAN Host, IPv6 WAN
Host and IPv6 Schedule. Click any of them, and you will be able to configure the corresponding
function.
89
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
4.16.1 IPv6 Rule
Choose menu “IPv6 Firewall” → “IPv6 Rule”, and then you can view and set Access Control
rules in the screen as shown in Figure 4-88.
Figure 4-88
 Enable IPv6 Firewall: Select the check box to enable the IPv6 Firewall function, so the
Default Filtering Rules can take effect.
 Description: Here displays the description of the IPv6 rule and this name is unique.
 IPv6 LAN Host: Here displays the LAN host selected in the corresponding rule.
 Target: Here displays the target selected in the corresponding rule.
 Schedule: Here displays the schedule selected in the corresponding rule.
 Status: Here displays the status of the rule either enabled or disabled.
 Edit: Here you can edit or delete an existing rule.
To add a new IPv6 rule:
1.
Click the Add New button, and you will see the screen as shown in Figure 4-89.
Figure 4-89
2.
Give a name (e.g. Rule_1) for the rule in the Description field.
3.
Select a host from the IPv6 LAN Host drop-down list or choose “Add IPv6 LAN Host”.
90
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
4.
Select a target from the IPv6 WAN Host drop-sown list or choose “Add IPv6 WAN Host”.
5.
Select a schedule from the IPv6 Schedule drop-down list or choose “Add IPv6 Schedule”.
6.
In the Action field, select Deny or Allow to deny or allow your entry.
7.
In the Status field, select Enabled or Disabled to enable or disable your entry.
8.
In the Direction field, select IN or OUT from the drop-down list for the direction.
9.
In the Protocol field, here are four options, All, TCP, UDP, and ICMPv6. Select one of them
from the drop-down list for the target.
10. Click the Save button to save the settings.
Click the Enable/ Disable Selected button to make selected entries enabled or disabled.
Click the Delete Selected button to delete selected entries.
4.16.2 IPv6 LAN Host
Choose menu “IPv6 Firewall” → “IPv6 LAN Host”, and then you can view and set a Host list in
the screen as shown in Figure 4-90.

Figure 4-90
Description: Here displays the description of the host and this description is unique.

IPv6 Address Info: Here displays the information about the host.

Edit: To modify an existing entry.
To add a new entry, please follow the steps below.
1.
Click the Add New button, and you will see the screen as shown in Figure 4-91.
Figure 4-91
2.
Create a unique name for the host (e.g. Host_1) in the Description field.
3.
Enter an IPv6 address in the IPv6 Address field.
4.
Enter the prefix length of the IPv6 address in the Prefix Length field.
5. Click the Save button to save the settings.
Click the Delete Selected button to delete selected entries.
91
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
4.16.3 IPv6 WAN Host
Choose menu “IPv6 Firewall” → “IPv6 WAN Host”, and then you can view and set a Host list in
the screen as shown in Figure 4-92.
Figure 4-92
 Description: Here displays the description about the WAN and this description is unique.
 Details: The details can be IPv6 address, prefix length or port.
 Edit: To modify an existing entry.
To add a new entry, please follow the steps below.
1.
Click the Add New button, and you will see the screen as shown in Figure 4-93.
Figure 4-93
2.
Create a unique description for the host (e.g. Host_1) in the Description field.
3.
Enter an IPv6 address in the IPv6 Address field.
4.
Enter the prefix length of the IPv6 address in the Prefix Length field.
5.
Click the Save button to save the settings.
Click the Delete Selected button to delete selected entries.
4.16.4 IPv6 Schedule
Choose menu “IPv6 Firewall” → “IPv6 Schedule”, and then you can view and set a Schedule list
in the next screen as shown in Figure 4-94.
Figure 4-94
92
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide

Description: Here displays the description of the schedule and this description is unique.

Edit: Here you can modify an existing schedule.
To add a new schedule, follow the steps below:
1.
Click Add New button and you will see the screen as shown in Figure 4-95.
Figure 4-95
2.
Create a unique description for the schedule (e.g. Schedule_1) in Description field.
3.
Select the day or days you need in Apply To field.
4.
In time field, you can select all day-24 hours or you may enter the Start Time and Stop Time
in the corresponding field.
5.
Click Save to save the settings.
Click the Clear Schedule button to clear your settings in the table.
Click the Delete Selected button to delete selected entries.
4.17 IPv6 Tunnel
IPv6 tunnel is a kind of transition mechanism to enable IPv6-only hosts to reach IPv4 services and
to allow isolated IPv6 hosts and networks to reach each-other over IPv4-only infrastructure before
IPv6 completely supplants IPv4. It is a temporary solution for networks that do not support native
dual-stack, where both IPv6 and IPv4 run independently.
Choose menu “IPv6 Tunnel”, and you will see the screen as shown in Figure 4-96.
93
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Figure 4-96

Enable: Check the box to enable IPv6 Tunnel function. It is disabled by default.

Mechanism: Select a type for IPv6 tunnel from the drop-down list. DS-Lite, 6RD and 6to4 are
supported.
1)
DS-Lite
This type is used in the situation that your WAN connection is IPv6 while LAN connection is IPv4.
Select DS-Lite, and you will see the screen as shown in Figure 4-97.
Figure 4-97

WAN Connection: Select a WAN connection from the drop-down list. Only the connected
WAN connections can be shown in the drop-down list.

Configuration Type: Select a configuration type for this tunnel. Auto means to obtain the
Remote IPv6 Address automatically while Manual means you set it manually.

Remote IPv6 Address: Enter the IPv6 address of the remote node.
 Note:
In this type, there should not have any IPv4 WAN connections. If there are IPv4 WAN connections,
the page will prompt you to delete all the IPv4 WAN connections.
2)
6RD
This type is used in the situation that your WAN connection is IPv4 while LAN connection is IPv6.
Select 6RD, and you will see the screen as shown in Figure 4-98.
94
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Figure 4-98

WAN Connection: Select a WAN connection from the drop-down list. Only the connected
WAN connections can be shown in the drop-down list.

Configuration Type: Select a configuration type for this tunnel. Auto means to obtain the
following parameters automatically while Manual means you set them manually. If Auto is
selected, only Dynamic IP connection can be selected from the drop-down list.

IPv4 Mask Length: The length of the selected WAN connection’s IPv4 mask.

6RD Prefix: The prefix of the 6RD tunnel.

6RD Prefix Length: The length of the 6RD prefix.

Border Relay IPv4 Address: The IPv4 address of the border relay router of 6RD tunnel.
 Note:
In this type, there should not have any IPv6 WAN connections. If there are IPv6 WAN connections,
the page will prompt you to delete all the IPv6 WAN connections.
3)
6to4
This type is used in the situation that your WAN connection is IPv4 while LAN connection is IPv6.
Select 6to4, and you will see the screen as shown in Figure 4-99.
Figure 4-99

WAN Connection: Select a WAN connection from the drop-down list. Only the connected
WAN connections can be shown in the drop-down list.
 Note:
In this type, there should not have any IPv6 WAN connections. If there are IPv6 WAN connections,
the page will prompt you to delete all the IPv6 WAN connections.
95
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
4.18 Bandwidth Control
Choose menu “Bandwidth Control”, and then you can configure the Upstream Bandwidth and
Downstream Bandwidth in the next screen. The values you configure should be less than
1000000Kbps. For optimal control of the bandwidth, please select the right Line Type and ask your
ISP for the total bandwidth of the egress and ingress.
Figure 4-100

Enable Bandwidth Control: Check this box so that the Bandwidth Control settings can take
effect.

Line Type: Select the right type for you network connection. If you don’t know how to choose,
please ask your ISP for the information.

Total Upstream Bandwidth - The upload speed through the WAN port.

Total Downstream Bandwidth - The download speed through the WAN port.

Description: This is the information about the rules such as address range.

Priority: Priority of Bandwidth Control rules. ‘1’ stands for the highest priority while ‘8’ stands
for the lowest priority. The total Upstream/ Downstream Bandwidth is first allocated to
guarantee all the Min Rate of Bandwidth Control rules. If there is any bandwidth left, it is first
allocated to the rule with the highest priority, then to the rule with the second highest priority,
and so on.

Upstream bandwidth: This field displays the max and mix upload bandwidth through the
WAN port, the default is 0.

Downstream bandwidth: This field displays the max and mix download bandwidth through
the WAN port, the default is 0.

Status: The status of this rule either Enabled or Disabled.

Edit: Click Edit to modify the rule.
To add/modify a Bandwidth Control rule, follow the steps below.
1.
Click Add New shown in Figure 4-100, you will see a new screen shown in Figure 4-101.
2.
Enter the information as the screen shown below.
96
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Figure 4-101
3.
Click the Save button.
Click the Enable/ Disable Selected button to make selected entries enabled or disabled.
Click the Delete Selected button to delete selected entries.
4.19 IP&MAC Binding
There are two submenus under the IP &MAC Binding menu: Binding Settings and ARP List.
Click any of them, and you will be able to scan or configure the corresponding function. The
detailed explanations for each submenu are provided below.
4.19.1 Binding Settings
This page displays the IP & MAC Binding Setting table; you can operate it in accord with your
desire (shown in Figure 4-102).
Figure 4-102

MAC Address: The MAC address of the controlled computer in the LAN.

IP Address: The assigned IP address of the controlled computer in the LAN.

Bounding Status: Check this option to enable ARP binding for a specific device.

Edit: To modify or delete an existing entry.
97
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or
Edit button, and then you will go to the next page. This page is used for adding or modifying an IP
& MAC Binding entry (shown in Figure 4-103.)
Figure 4-103
To add IP & MAC Binding entries, follow the steps below.
1.
Click the Add New button as shown in Figure 4-102.
2.
Enter the MAC Address and IP Address.
3.
Select the Bind checkbox.
4.
Click the Save button to save it.
To modify or delete an existing entry, follow the steps below.
1.
Find the desired entry in the table.
2.
Click Edit as desired on the Edit column.
Click the Enable/ Disable Selected button to make selected entries enabled or disabled.
Click the Delete Selected button to delete selected entries.
4.19.2 ARP List
To manage the computer, you could observe the computers in the LAN by checking the
relationship of MAC address and IP address on the ARP list, and you could also configure the
items on the ARP list. This page displays the ARP List; it shows all the existing IP & MAC Binding
entries (shown in Figure 4-104).
Figure 4-104




MAC Address: The MAC address of the controlled computer in the LAN.
IP Address: The assigned IP address of the controlled computer in the LAN.
Status: Indicates whether or not the MAC and IP addresses are bound.
Load: Load the item to the IP & MAC Binding list.
98
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Click the Load Selected button to load selected items to the IP & MAC Binding list.
Click the Refresh button to refresh all items.
4.20 Dynamic DNS
Choose menu “Dynamic DNS”, and you can configure the Dynamic DNS function.
The modem router offers the DDNS (Dynamic Domain Name System) feature, which allows the
hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself)
and a dynamic IP address, and then your friends can connect to your server by entering your
domain name no matter what your IP address is. Before using this feature, you need to sign up for
DDNS service providers such as www.dyndns.org. The Dynamic DNS client service provider will
give you a password or key.
Figure 4-105

Service Provider: This field displays the service provider of DDNS.

Domain Name: Enter the Domain name you received from dynamic DNS service provider.

Username & Password: Type the “User Name” and “Password” for your DDNS account.

Enable DDNS: Activate the DDNS function or not.

Login/ Logout: Login to or logout of the DDNS service.
4.21 Diagnostic
Choose “Diagnostic”, you can view the test results for the connectivity of the physical layer and
protocol layer for both LAN and WAN sides in the screen. Select the desired type and click the start
button.
99
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Figure 4-106
4.22 System Tools
Choose menu “System Tools”, and you can see the submenus under the main menu: System
Log, Time Settings, Manage Control, CWMP Settings, SNMP Settings, Backup & Restore,
Factory Defaults, Firmware Upgrade, Reboot and Statistics. Click any of them, and you will be
able to configure the corresponding function. The detailed explanations for each submenu are
provided below.
4.22.1 System Log
Choose menu “System Tools” → “System Log”, and then you can view the logs of the modem
router.
100
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Figure 4-107

Log Type: By selecting the log type, only logs of this type will be shown.

Log Level: By selecting the log level, only logs of this level will be shown.

Refresh: Refresh the page to show the latest log list.

Clear Log: All the logs will be deleted from the modem router permanently, not just from the
page.

Save Log: Click to save all the logs in a txt file.

Log Settings: Click to set the logs in the screen (shown in Figure 4-108).
Figure 4-108

Save Locally: If Save Locally is selected, events will be recorded in the local memory.

Minimum Level: Select the Minimum level in the drop-down list, for the Minimum Level, all
logged events above or equal to the selected level will be displayed.

Save Remotely: If Save Remotely is selected, events will be sent to the specified IP address
and UDP port of the remote system log server.
Click the Save button to save your settings.
4.22.2 Time Settings
Choose menu “System Tools” → “Time Settings”, and then you can configure the time on the
following screen.
Figure 4-109
101
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide

Time Zone: Select your local time zone from this pull down list.

Date: Enter your local date in MM/DD/YY into the right blanks.

Time: Enter your local time in HH/MM/SS into the right blanks.

NTP Server 1 / NTP Server 2: Enter the address or domain of the NTP Server 1 or NTP
Server 2, and then the modem router will get the time from the NTP Server preferentially. In
addition, the modem router built-in some common NTP Servers, so it can get time
automatically once it connects the Internet.
To set time manually:
1.
Select your local time zone.
2.
Enter the Date in Year/Month/Day format.
3.
Enter the Time in Hour/Minute/Second format.
4.
Click Save.
To set time automatically:
1.
Select your local time zone.
2.
Enter the address or domain of the NTP Server 1 or NTP Server 2.
3.
Click the Get GMT button to get system time from Internet if you have connected to the
Internet.
4.22.3 Manage Control
Choose “System Tools” → “Manage Control”, you can see the screen (shown in Figure 4-110)
Figure 4-110

Current User Status: This box displays the information about User Type, User Name, Host
IP Address and Host MAC Address.
102
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide

Account Management: Here you can set the account user information about Old Password,
New User Name, New Password and Confirm Password.

Service Configuration: Here you can modify the port of the modem router’s
Web-Management page and limit the hosts which can login this modem router’s
Web-Management page.

ICMP(ping): If you select Remote, PCs in public network can ping WAN address of the
modem router. If you select Local, PCs in private network can ping LAN address of the
modem router.
4.22.4 CWMP Settings
Choose “System Tools” → “CWMP Settings”, you can configure the CWMP function in the
screen.
The modem router offers CWMP feature. The function supports TR-069 protocol which collects
information, diagnoses the devices and configures the devices automatically via ACS
(Auto-Configuration Server).
Figure 4-111

CWMP: Select enable the CWMP function.

Inform: Enable or disable the function. If enabled, the information will be informed to ACS
server periodically.

Inform Interval: Enter the interval time here.

ACS URL: Enter the website of ACS which is provided by your ISP.

ACS User Name/Password: Enter the User Name and password to login the ACS server.

Interface used by TR-069 client: Select the interface used by TR-069 client.

Display SOAP messages on serial console: Enable or disable this function.

Connection Request User Name/Password: Enter the User Name and Password that
provided the ACS server to login the modem router.
103
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide

Connection Request Path: Enter the path that connects to the ACS server.

Connection Request Port: Enter the port that connects to the ACS server.

Connection Request URL: Enter the URL that connects to the ACS server.
4.22.5 SNMP Settings
Choose “System Tools”“SNMP Settings”, you can see the SNMP-Configuration screen as
shown below.
SNMP (Simple Network Management Protocol) has been widely applied in the computer networks
currently, which is used for ensuring the transmission of the management information between
any two nodes. In this way, network administrators can easily search and modify the information
on any node on the network. Meanwhile, they can locate faults promptly and implement the fault
diagnosis, capacity planning and report generating.
Figure 4-112
An SNMP Agent is an application running on the modem router that performs the operational role
of receiving and processing SNMP messages, sending responses to the SNMP manager, and
sending traps when an event occurs. So a router contains SNMP "agent" software can be
monitored and/or controlled by SNMP Manager using SNMP messages.
4.22.6 Backup & Restore
Choose menu “System Tools” → “Backup & Restore”, and then you can save the current
configuration of the modem router as a backup file and restore the configuration via a backup file
as shown in Figure 4-113.
Figure 4-113

Click the Backup button to save all configuration settings as a backup file in your local
computer.

To upgrade the modem router 's configuration, follow these instructions.
•
Click the Browse button to find the configuration file which you want to restore.
•
Click the Restore button to update the configuration with the file whose path is the one
you have input or selected in the blank.
104
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
 Note:
The current configuration will be covered with the uploading configuration file. Wrong process will
lead the device unmanaged. The restoring process lasts for 20 seconds and the modem router will
restart automatically then. Keep the power of the modem router on during the process, in case of
any damage.
4.22.7 Factory Defaults
Choose menu “System Tools → Factory Defaults”, and then and you can restore the
configurations of the modem router to factory defaults on the following screen
Figure 4-114
Click the Restore button to reset all configuration settings to their default values.
•
The default User Name: admin
•
The default Password: admin
•
The default Subnet Mask: 255.255.255.0
 Note:
All changed settings will be lost when defaults are restored.
4.22.8 Firmware Upgrade
Choose menu “System Tools → Firmware Upgrade”, and then you can update the latest
version of firmware for the modem router on the following screen.
Figure 4-115
105
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide

Firmware Version: Displays the current firmware version.

Hardware Version: Displays the current hardware version. The hardware version of the
upgrade file must accord with the modem router’s current hardware version.
To upgrade the modem router's firmware, follow these instructions below:
1)
Download a most recent firmware upgrade file from our website (www.tp-link.com).
2)
Enter or select the path name where you save the downloaded file on the computer into the
File Name blank.
3)
Click the Upgrade button.
4)
The modem router will reboot while the upgrading has been finished.
 Note:
1)
New firmware versions are posted at http://www.tp-link.com and can be downloaded for free.
There is no need to upgrade the firmware unless the new firmware has a new feature you
want to use. However, when experiencing problems caused by the modem router rather than
the configuration, you can try to upgrade the firmware.
2)
When you upgrade the modem router's firmware, you may lose its current configurations, so
before upgrading the firmware please write down some of your customized settings to avoid
losing important settings.
3)
Do not turn off the modem router or press the Reset button while the firmware is being
upgraded. Loss of power during the upgrade could damage the modem router.
4)
The firmware version must correspond to the hardware.
5)
The upgrade process takes a few moments and the modem router restarts automatically
when the upgrade is complete.
4.22.9 Reboot
Choose menu “System Tools” → “Reboot”, and then you can click the Reboot button to reboot
the modem router via the next screen.
Figure 4-116
Some settings of the modem router will take effect only after rebooting, which include
•
Change the LAN IP Address (system will reboot automatically).
•
Change the DHCP Settings.
•
Change the Wireless configurations.
•
Change the Web Management Port.
•
Upgrade the firmware of the modem router (system will reboot automatically).
106
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
•
Restore the modem router's settings to factory defaults (system will reboot
automatically).
•
Update the configuration with the file (system will reboot automatically.
4.22.10 Statistics
Choose menu “System Tools” → “Statistics”, and then you can view the statistics of the Modem
router, including total traffic and current traffic of the last Packets Statistic Interval.
Figure 4-117

Statistics Status: Enable or Disable. The default value is disabled. To enable it, click the
Enable. If it is disabled, the function of DoS protection in Security settings will be disabled.

Statistics Interval (5-60): The default value is 10. Select a value between 5 and 60 seconds
in the drop-down list. The Packets Statistic interval indicates the time section of the packets
statistic.
Click Reset All to reset the values of all the entries to zero.
Click Delete All to delete all entries in the table.
Click the Refresh button to refresh immediately.
Statistics Table:
IP/MAC Address
The IP and MAC address are displayed with related statistics.
Packets
The total number of packets received and transmitted by the
modem router.
Bytes
The total number of bytes received and transmitted by the
modem router.
Packets
The total number of packets received and transmitted in the last
Packets Statistic interval seconds.
Bytes
The total number of bytes received and transmitted in the last
Packets Statistic interval seconds.
ICMP
Tx
The number of the ICMP packets transmitted to WAN per second
at the specified Packets Statistics interval. It is shown like
“current transmitting rate / Max transmitting rate”.
Total
Current
107
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
UDP Tx
The number of UDP packets transmitted to the WAN per second
at the specified Packets Statistics interval. It is shown like
“current transmitting rate / Max transmitting rate”.
SYN Tx
The number of TCP SYN packets transmitted to the WAN per
second at the specified Packets Statistics interval. It is shown like
“current transmitting rate / Max transmitting rate”.
Reset
Reset the value of he entry to zero.
Delete
Delete the existing entry in the table.
Operation
4.23 Logout
Choose “Logout”, and you will back to the login screen as shown in Figure 4-118.
Figure 4-118
108
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Appendix A: Specifications
General
ANSI T1.413, ITU G.992.1, ITU G.992.3, ITU G.992.5, ITU G.993.2
Standards and Protocols
Safety & Emission
IEEE802.11p, IEEE802.11e, IEEE802.11b, IEEE802.11g,
IEEE802.11n, IEEE802.3, IEEE802.3u, TCP/IP, PPPoA, PPPoE,
SNTP, HTTP, DHCP, ICMP, NAT
FCC, CE
Four 10/100/1000M Auto-Negotiation RJ45 ports（Auto MDI/MDIX)
Ports
One RJ11 port
Two USB 2.0 ports
Power,
LEDs
DSL,
Internet,
Wireless 5GHz,
back panel)
WPS,
Wireless 2.4GHz,
1,2,3,4(LAN),
(USB on the
10Base-T: UTP category 3, 4, 5 cable
100Base-TX: UTP category-5, 5e cable
Network Medium
1000Base-TX: UTP category-5, 5e cable
Max line length: 6.5Km
Downstream: Up to 100Mbps
Data Rates
Upstream: Up to 100Mbps
Windows 8/7/Vista/XP or Mac OS or Linux-based operating system
System Requirement
Microsoft Internet Explorer, Firefox, Chrome or Safari browser for
web-based configuration
Physical and Environment
Working Temperature
Working Humidity
Storage Temperature
Storage Humidity
℃ ~ 40℃
10% ~ 90% RH (non-condensing)
-40
℃ ~ 70℃
5% ~ 90% RH (non-condensing)
109
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Appendix B: Troubleshooting
T1. How do I restore my modem router’s configuration to its factory default
settings?
With the modem router powered on, press and hold the RESET button on the rear panel for 8 to
10 seconds before releasing it.
 Note:
Once the modem router is reset, the current configuration settings will be lost and you will need to
re-configure the router.
T2. What can I do if I don’t know or forget my password?
1) Restore the modem router’s configuration to its factory default settings. If you don’t know how
to do that, please refer to T1.
2) Use the default user name and password: admin, admin.
3) Try to configure your modem router once again by following the instructions in 3.2 Quick
Installation Guide.
T3. What can I do if I cannot access the web-based configuration page?
1) Configure your computer’s IP Address.
For Mac OS X

Click the Apple icon on the upper left corner of the screen.

Go to “System Preferences -> Network”.

Select Airport on the left menu bar, and then click Advanced for wireless configuration; or
select Ethernet for wired configuration.

In the Con­figure IPv4 box under TCP/IP, select Using DHCP.

Click Apply to save the settings.
For Windows 7

Click “Start -> Control Panel -> Network and Internet -> View network status -> Change
adapter settings”.

Right-click Wireless Network Connection (or Local Area Connection), and then click
Properties.

Select Internet Protocol Version 4 (TCP/IPv4), and then click Properties.

Select Obtain an IP address automatically and Obtain DNS server address automatically.
Then click OK.
For Windows XP

Click “Start -> Control Panel -> Network and Internet Connections -> Network
Connections”.

Right-click Wireless Network Connection (or Local Area Connection), and then click
Properties.

Select Internet Protocol (TCP/IP), and then click Properties.
110
TD-W9980B

N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Select Obtain an IP address automatically and Obtain DNS server address automatically.
Then click OK.
For Windows 8

Move your mouse to the lower right corner and you will see Search icon
in the Popups. Go
to “
-> Apps”. Type Control Panel in the search box and press Enter, then you will go to
Control Panel.

Click “View network status and tasks > Change adapter settings”.

Right-click “Ethernet” and then select Properties.

Double-click Internet Protocol Version 4 (TCP/IPv4). Select Obtain an IP address
automatically, choose Obtain DNS server address automatically and then click OK.
2) Configure your IE browser
Open your IE browser, click
Tools tab and you will see the
following screen.
Click Internet Options
Select Never dial a
connection
Click OK
111
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Now, try to log on to the Web-based management page again after the above settings have been
configured. If you still cannot access the configuration page, please restore your modem router’s
factory default settings and reconfigure your modem router following the instructions in 3.2 Quick
Installation Guide. Please feel free to contact our Technical Support if the problem still exists.
T4. What can I do if I cannot access the Internet?
1)
Check to see if all the connectors are connected well, including the telephone line, Ethernet
cables and power adapter.
2)
Check to see if you can log on to the Web-Management page of the modem router. If you can,
try the following steps. If you cannot, please set your computer referring to T3 then try to see if
you can access the Internet. If the problem persists, please go to the next step.
3)
Consult your ISP and make sure all the VPI/VCI, Connection Type, account username and
password are correct. If there are any mistakes, please correct the settings and try again.
4)
If you still cannot access the Internet, please restore your modem router to its factory default
settings and reconfigure your modem router by following the instructions in 3.2 Quick
Installation Guide.
5)
Please contact our Technical Support if the problem still exists.
 Note:
For more details about Troubleshooting and Technical Support contact information, please log on
to our Technical Support Website: http://www.tp-link.com/en/support
112
TD-W9980B
N600 Wireless Dual Band Gigabit VDSL2 Modem Router (Annex B) User Guide
Appendix C: Technical Support
Technical Support

For more troubleshooting help, go to:
http://www.tp-link.com/en/support/faq
 To download the latest Firmware, Driver, Utility and User Guide, go to:
http://www.tp-link.com/en/support/download
 For all other technical support, please contact us by using the following details:
Global
Tel: +86 755 2650 4400
Fee: Depending on rate of different carriers, IDD.
E-mail: support@tp-link.com
Service time: 24hrs, 7 days a week
USA/Canada
Toll Free: +1 866 225 8139
E-mail: support.usa@tp-link.com(USA)
support.ca@tp-link.com(Canada)
Service time: 24hrs, 7 days a week
Turkey
Tel: 0850 7244 488 (Turkish Service)
Fee: Depending on rate of different carriers.
E-mail: support.tr@tp-link.com
Service time: 09:00 to 21:00, 7 days a week
Ukraine
Tel: 0800 505 508
Fee: Free for Landline; Mobile: Depending on
rate of different carriers
E-mail: support.ua@tp-link.com
Service time: Monday to Friday, 10:00 to 22:00
Brazil
Toll Free: 0800 608 9799 (Portuguese Service)
E-mail: suporte.br@tp-link.com
Service time: Monday to Friday, 09:00 to 20:00;
Saturday, 09:00 to 15:00
Indonesia
Tel: (+62) 021 6386 1936
Fee: Depending on rate of different carriers.
E-mail: support.id@tp-link.com
Service time: Sunday to Friday, 09:00 to 12:00,
13:00 to 18:00 *Except public holidays
Australia/New Zealand
Tel: NZ 0800 87 5465 (Toll Free)
AU 1300 87 5465 (Depending on 1300 policy.)
E-mail: support.au@tp-link.com (Australia)
support.nz@tp-link.com (New Zealand)
Service time: 24hrs, 7 days a week
Germany/Austria
Tel: +49 1805 875 465 (German Service)
+49 1805 TPLINK
+43 820 820 360
Fee: Landline from Germany: 0.14EUR/min.
Landline from Austria: 0.20EUR/min.
E-mail: support.de@tp-link.com
Service time: Monday to Friday, 09:00 to 12:30
and 13:30 to 18:00. GMT+1 or GMT+2 (DST in
Germany)
*Except bank holidays in Hesse
Singapore
Tel: +65 6284 0493
Fee: Depending on rate of different carriers.
E-mail: support.sg@tp-link.com
Service time: 24hrs, 7 days a week
UK
Tel: +44 (0) 845 147 0017
Fee: Landline: 1p-10.5p/min, depending on the time
of day. Mobile: 15p-40p/min, depending on your
mobile network.
E-mail: support.uk@tp-link.com
Service time: 24hrs, 7 days a week
Italy
Tel: +39 023 051 9020
Fee: Depending on rate of different carriers.
E-mail: support.it@tp-link.com
Service time: Monday to Friday, 09:00 to 13:00;
14:00 to 18:00
Malaysia
Toll Free: 1300 88 875 465
Email: support.my@tp-link.com
Service time: 24hrs, 7 days a week
Poland
Tel: +48 (0) 801 080 618
+48 223 606 363 (if calls from mobile phone)
Fee: Depending on rate of different carriers.
E-mail: support.pl@tp-link.com
Service time: Monday to Friday, 09:00 to 17:00.
GMT+1 or GMT+2 (DST)
France
Tel: 0820 800 860 (French service)
Fee: 0.118 EUR/min from France
Email: support.fr@tp-link.com
Service time: Monday to Friday, 09:00 to 18:00
*Except French Bank holidays
Switzerland
Tel: +41 (0) 848 800 998 (German Service)
Fee: 4-8 Rp/min, depending on rate of different
time.
E-mail: support.ch@tp-link.com
Service time: Monday to Friday, 09:00 to 12:30 and
13:30 to 18:00. GMT+1 or GMT+2 (DST)
Russian Federation
Tel: 8 (499) 754 5560 (Moscow NO.)
8 (800) 250 5560 (Toll-free within RF)
E-mail: support.ru@tp-link.com
Service time: From 09:00 to 21:00 (Moscow time)
*Except weekends and holidays in RF
113

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract
Tagged PDF                      : Yes
Page Mode                       : UseOutlines
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Modify Date                     : 2014:07:28 16:36:27+08:00
Create Date                     : 2014:07:28 13:54:27+08:00
Metadata Date                   : 2014:07:28 16:36:27+08:00
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Document ID                     : uuid:30695e81-7fa9-42f6-8129-e00b73267bf9
Instance ID                     : uuid:6c503b77-39b6-4862-9de5-0bdef63dfff2
Subject                         : 429
Format                          : application/pdf
Title                           : 
Description                     : 
Creator                         : 
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Source Modified                 : D:20140728055346
Company                         : 
Manager                         : 
Comments                        : 
Page Count                      : 123
Page Layout                     : OneColumn
Author                          : 

EXIF Metadata provided by EXIF.tools