TP Link Technologies WR710N 150Mbps Wireless N Mini Pocket Router User Manual TL WR710N US User Guide

TP-Link Technologies Co., Ltd. 150Mbps Wireless N Mini Pocket Router TL WR710N US User Guide

TL-WR710N(US)_User Guide

TL-WR710N150Mbps Wireless N Mini Pocket Router - Advanced Edition Rev: 1.0.0 1910010794
COPYRIGHT & TRADEMARKS Specifications are subject to change without notice. is a registered trademark of TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered trademarks of their respective holders. No part of the specifications may be reproduced in any form or by any means or used to make any derivative such as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright © 2013 TP-LINK TECHNOLOGIES CO., LTD. All rights reserved.http://www.tp-link.com
FCC STATEMENTThis equipment has been tested and found to comply with the limits for a Class B digital device,pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protectionagainst harmful interference in a residential installation. This equipment generates, uses and canradiate radio frequency energy and, if not installed and used in accordance with the instructions,may cause harmful interference to radio communications. However, there is no guarantee thatinterference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipment offand on, the user is encouraged to try to correct the interference by one or more of the followingmeasures:xReorient or relocate the receiving antenna.xIncrease the separation between the equipment and receiver.xConnect the equipment into an outlet on a circuit different from that to which the receiveris connected.xConsult the dealer or an experienced radio/ TV technician for help.This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions:1˅This device may not cause harmful interference.2˅This device must accept any interference received, including interference that maycause undesired operation.Any changes or modifications not expressly approved by the party responsible for compliancecould void the user’s authority to operate the equipment.Note: The manufacturer is not responsible for any radio or TV interference caused byunauthorized modifications to this equipment. Such modifications could void the user’s authorityto operate the equipment.FCC RFRadiation Exposure Statement:This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. To comply with FCC RF exposure compliance requirements, this grant is applicable to only Mobile Configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.”
CE Mark Warning This is a class B product. In a domestic environment, this product may cause radio interference, in which case the user may be required to take adequate measures. Canadian Compliance Statement This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1)This device may not cause interference, and (2)This device must accept any interference, including interference that may cause undesired operation of the device. Cet appareil est conforme aux norms CNR exemptes de licence d’Industrie Canada. Le fonctionnement est soumis aux deux conditions suivantes: (1)cet appareil ne doit pas provoquer d’interférences et (2)cet appareil doit accepter toute interférence, y compris celles susceptibles de provoquer un fonctionnement non souhaité de l’appareil. Industry Canada Statement Complies with the Canadian ICES-003 Class B specifications. Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. This device complies with RSS 210 of Industry Canada. This Class B device meets all the requirements of the Canadian interference-causing equipment regulations. Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du Canada. NCC Notice & BSMI Notice ⊼ᛣʽձ᪮Ԣࡳ⥛䳏⊶䔏ᇘᗻ䳏″ㅵ⧚䕺⊩㄀कѠṱ㍧ൟᓣ䁡䄝ড়ḐПԢࡳ⥛ᇘ丏䳏″ˈ䴲㍧䀅ৃˈ݀ৌǃଚ㰳៪Փ⫼㗙ഛϡᕫ᪙㞾䅞᳈丏⥛ǃࡴ໻ࡳ⥛៪䅞᳈ॳ䀁㿜П⡍ᗻ៪ࡳ㛑DŽ㄀कಯṱԢࡳ⥛ᇘ丏䳏″ПՓ⫼ϡᕫᕅ䷓亯㟾ᅝܼঞᑆ᫒ড়⊩䗮㸠˗㍧ⱐ⧒᳝ᑆ᫒⧒䈵ᰖˈឝゟेذ⫼ˈϺᬍ୘㟇⛵ᑆ᫒ᰖᮍᕫ㑐㑠Փ⫼DŽࠡ䷙ড়⊩䗮ֵˈᣛձ䳏ֵ㽣ᅮ԰ὁП⛵㎮䳏ֵDŽԢࡳ⥛ᇘ丏䳏″䳔ᖡফড়⊩䗮ֵ៪Ꮉὁǃ⾥ᅌҹঞ䝿Ⱆ⫼䳏⊶䔏ᇘᗻ䳏″䀁٭Пᑆ᫒DŽ
ᅝܼ䃂䀶ঞ⊼ᛣџ䷙ƽ䂟Փ⫼ॳ㺱䳏⑤կឝ఼៪া㛑ᣝ✻ᴀ⫶ક⊼ᯢⱘ䳏⑤串ൟՓ⫼ᴀ⫶કDŽƽ⏙┨ᴀ⫶કПࠡ䂟ܜᢨᥝ䳏⑤㎮DŽ䂟࣓Փ⫼⎆储ǃై䳻⏙┨ࡥ៪▩Ꮧ䘆㸠⏙┨DŽƽ⊼ᛣ䰆╂ˈ䂟࣓ᇛ∈៪݊Ҫ⎆储┥☥ࠄᴀ⫶કϞDŽǂƽᦦῑ㟛䭟ষկ䗮乼Փ⫼ˈҹ⺎ֱᴀ⫶કⱘ᪡԰ৃ䴴Ϻ䰆ℶ䘢➅ˈ䂟࣓ฉา៪㽚㪟䭟ষDŽƽ䂟࣓ᇛᴀ⫶ક㕂ᬒᮐ䴴䖥➅⑤ⱘഄᮍDŽ䰸䴲᳝ℷᐌⱘ䗮乼ˈ৺ࠛϡৃᬒ೼ᆚ䭝ԡ㕂ЁDŽƽ䂟ϡ㽕⾕㞾ᠧ䭟″←ˈϡ㽕௫䀺㞾㸠㎁ׂᴀ⫶કˈ䂟⬅ᥜ⃞ⱘᇜὁҎ຿䘆㸠ℸ䷙Ꮉ԰DŽSafety Information z When product has power button, the power button is one of the way to shut off the product; when there is no power button, the only way to completely shut off power is to disconnect the product or the power adapter from the power source. z Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and voiding the limited warranty. If you need service, please contact us. z Avoid water and wet locations. z This product can be used in the following countries:
TP-LINK TECHNOLOGIES CO., LTDTP-LINK TECHNOLOGIES CO., LTD. Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan Rd, Nanshan, Shenzhen, China DECLARATION OF CONFORMITY For the following equipment: Product Description: 150Mbps Wireless N Mini Pocket Router - Advanced Edition Model No.: TL-WR710N Trademark: TP-LINKWe declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives: Directives 1999/5/EC, Directives 2004/108/EC, Directives 2006/95/EC, Directives 1999/519/EC, Directives 2011/65/EU The above product is in conformity with the following standards or other normative documents ETSI EN 300 328 V1.7.1: 2006 ETSI EN 301 489-1 V1.9.2:2011& ETSI EN 301 489-17 V2.2.1:2012 EN 55022:2010 EN 55024:2010 EN 61000-3-2:2006+A1:2009+A2:2009 EN 61000-3-3:2008EN 60950-1:2006+A11˖2009+A1:2010+A12:2011 EN 62311:2008 The product carries the CE Mark: Person is responsible for marking this declaration: Yang Hongliang Product Manager of International Business Date of issue: 2013
- I -CONTENTSPackage Contents..................................................................................................................................1Chapter 1.Introduction.......................................................................................................................21.1 Overview of the Router .......................................................................................................21.2 Conventions ........................................................................................................................31.3 Main Features .....................................................................................................................31.4 Panel Layout .......................................................................................................................3Chapter 2. Connecting the Router .....................................................................................................52.1 System Requirements.........................................................................................................52.2 Installation Environment Requirements ..............................................................................52.3 Connecting the Router ........................................................................................................52.3.1 Wireless Router Mode ............................................................................................62.3.2 Access Point Mode.................................................................................................62.3.3 Repeater Mode.......................................................................................................72.3.4 Client Mode.............................................................................................................82.3.5 WISP Client Router Mode ......................................................................................8Chapter 3.Quick Installation Guide................................................................................................ 103.1 TCP/IP Configuration ....................................................................................................... 103.2 Quick Installation Guide ................................................................................................... 133.2.1 Wireless Router Mode ......................................................................................... 143.2.2 Access Point Mode.............................................................................................. 173.2.3 Repeater Mode.................................................................................................... 193.2.4 Client Mode.......................................................................................................... 213.2.5 WISP Client Router Mode ................................................................................... 23Chapter 4.Configuration for Wireless Router Mode .................................................................... 274.1 Login ................................................................................................................................ 274.2 Status ............................................................................................................................... 274.3 Quick Setup...................................................................................................................... 304.4 WPS ................................................................................................................................. 304.5 Working Mode.................................................................................................................. 344.6 Network ............................................................................................................................ 354.6.1 WAN..................................................................................................................... 354.6.2 MAC Clone .......................................................................................................... 44
- II -4.6.3 LAN...................................................................................................................... 454.7 Wireless ........................................................................................................................... 464.7.1 Wireless Settings................................................................................................. 464.7.2 Wireless Security................................................................................................. 484.7.3 Wireless MAC Filtering ........................................................................................ 514.7.4 Wireless Advanced .............................................................................................. 534.7.5 Wireless Statistics................................................................................................ 544.8 DHCP ............................................................................................................................... 554.8.1 DHCP Settings..................................................................................................... 554.8.2 DHCP Client List.................................................................................................. 564.8.3 Address Reservation ........................................................................................... 574.9 USB Settings.................................................................................................................... 584.9.1 Storage Sharing................................................................................................... 584.9.2 Media Server ....................................................................................................... 604.9.3 User Accounts...................................................................................................... 624.10 Forwarding ....................................................................................................................... 634.10.1 Virtual Servers ..................................................................................................... 644.10.2 Port Triggering ..................................................................................................... 654.10.3 DMZ ..................................................................................................................... 674.10.4 UPnP ................................................................................................................... 684.11 Security ............................................................................................................................ 694.11.1 Basic Security...................................................................................................... 694.11.2 Advanced Security............................................................................................... 704.11.3 Local Management .............................................................................................. 724.11.4 Remote Management .......................................................................................... 734.12 Parental Control ............................................................................................................... 744.13 Access Control................................................................................................................. 764.13.1 Rule ..................................................................................................................... 764.13.2 Host ..................................................................................................................... 794.13.3 Target................................................................................................................... 814.13.4 Schedule.............................................................................................................. 83
- III -4.14 Advanced Routing............................................................................................................854.14.1 Static Routing List................................................................................................ 854.14.2 System Routing Table.......................................................................................... 864.15 Bandwidth Control............................................................................................................ 874.15.1 Control Settings ................................................................................................... 874.15.2 Rule List............................................................................................................... 874.16 IP & MAC Binding ............................................................................................................894.16.1 Binding Setting .................................................................................................... 894.16.2 ARP List............................................................................................................... 914.17 Dynamic DNS................................................................................................................... 914.17.1 No-IP DDNS ........................................................................................................ 924.17.2 Comexe.cn DDNS ............................................................................................... 924.17.3 Dyndns org DDNS ............................................................................................... 934.18 System Tools.................................................................................................................... 944.18.1 Time Settings....................................................................................................... 954.18.2 Diagnostic............................................................................................................ 964.18.3 Firmware Upgrade............................................................................................... 974.18.4 Factory Defaults................................................................................................... 984.18.5 Backup & Restore................................................................................................ 994.18.6 Reboot ................................................................................................................. 994.18.7 Password........................................................................................................... 1004.18.8 System Log........................................................................................................ 1004.18.9 Statistics............................................................................................................. 101Chapter 5.Configuration for Access Point Mode ....................................................................... 1035.1 Login .............................................................................................................................. 1035.2 Status ............................................................................................................................. 1035.3 Quick Setup.................................................................................................................... 1055.4 WPS ............................................................................................................................... 1055.5 Working Mode.................................................................................................................1105.6 Network ...........................................................................................................................1105.6.1 LAN.....................................................................................................................1105.7 Wireless .......................................................................................................................... 111
- IV -5.7.1 Wireless Settings................................................................................................1125.7.2 Wireless Security................................................................................................1135.7.3 Wireless MAC Filtering .......................................................................................1165.7.4 Wireless Advanced .............................................................................................1185.7.5 Wireless Statistics...............................................................................................1195.8 DHCP ............................................................................................................................. 1205.8.1 DHCP Settings................................................................................................... 1205.8.2 DHCP Client List................................................................................................ 1215.8.3 Address Reservation ......................................................................................... 1225.9 USB Settings.................................................................................................................. 1235.9.1 Storage Sharing................................................................................................. 1235.9.2 Media Server ..................................................................................................... 1255.9.3 User Accounts.................................................................................................... 1275.10 System Tools.................................................................................................................. 1295.10.1 Diagnostic.......................................................................................................... 1295.10.2 Firmware Upgrade............................................................................................. 1315.10.3 Factory Defaults................................................................................................. 1325.10.4 Backup & Restore.............................................................................................. 1325.10.5 Reboot ............................................................................................................... 1335.10.6 Password........................................................................................................... 1345.10.7 System Log........................................................................................................ 135Chapter 6.Configuration for Repeater Mode .............................................................................. 1366.1 Login .............................................................................................................................. 1366.2 Status ............................................................................................................................. 1366.3 Quick Setup.................................................................................................................... 1386.4 Working Mode................................................................................................................ 1386.5 Network .......................................................................................................................... 1396.5.1 LAN.................................................................................................................... 1396.6 Wireless ......................................................................................................................... 1406.6.1 Wireless Settings............................................................................................... 1406.6.2 Wireless Security............................................................................................... 1426.6.3 Wireless MAC Filtering ...................................................................................... 144
- V -6.6.4 Wireless Advanced ............................................................................................ 1466.6.5 Wireless Statistics.............................................................................................. 1476.7 DHCP ............................................................................................................................. 1486.7.1 DHCP Settings................................................................................................... 1486.7.2 DHCP Client List................................................................................................ 1506.7.3 Address Reservation ......................................................................................... 1506.8 USB Settings.................................................................................................................. 1526.8.1 Storage Sharing................................................................................................. 1526.8.2 Media Server ..................................................................................................... 1546.8.3 User Accounts.................................................................................................... 1566.9 System Tools.................................................................................................................. 1586.9.1 Diagnostic.......................................................................................................... 1586.9.2 Firmware Upgrade............................................................................................. 1596.9.3 Factory Defaults................................................................................................. 1606.9.4 Backup & Restore.............................................................................................. 1616.9.5 Reboot ............................................................................................................... 1626.9.6 Password........................................................................................................... 1626.9.7 System Log........................................................................................................ 163Chapter 7.Configuration for Client Mode.................................................................................... 1647.1 Login .............................................................................................................................. 1647.2 Status ............................................................................................................................. 1647.3 Quick Setup.................................................................................................................... 1667.4 Working Mode................................................................................................................ 1667.5 Network .......................................................................................................................... 1677.5.1 LAN.................................................................................................................... 1677.6 Wireless ......................................................................................................................... 1687.6.1 Wireless Settings............................................................................................... 1687.6.2 Wireless Security............................................................................................... 1697.7 DHCP ............................................................................................................................. 1727.7.1 DHCP Settings................................................................................................... 1727.7.2 DHCP Client List................................................................................................ 1737.7.3 Address Reservation ......................................................................................... 174
- VI -7.8 USB Settings.................................................................................................................. 1757.8.1 Storage Sharing................................................................................................. 1757.8.2 Media Server ..................................................................................................... 1777.8.3 User Accounts.................................................................................................... 1797.9 System Tools.................................................................................................................. 1817.9.1 Diagnostic.......................................................................................................... 1817.9.2 Firmware Upgrade............................................................................................. 1837.9.3 Factory Defaults................................................................................................. 1847.9.4 Backup & Restore.............................................................................................. 1847.9.5 Reboot ............................................................................................................... 1857.9.6 Password........................................................................................................... 1867.9.7 System Log........................................................................................................ 187Chapter 8.Configuration for WISP Client Router Mode ............................................................. 1888.1 Login .............................................................................................................................. 1888.2 Status ............................................................................................................................. 1888.3 Quick Setup.................................................................................................................... 1918.4 Working Mode................................................................................................................ 1918.5 Network .......................................................................................................................... 1928.5.1 WAN................................................................................................................... 1928.5.2 MAC Clone ........................................................................................................ 2018.5.3 LAN.................................................................................................................... 2028.6 Wireless ......................................................................................................................... 2038.6.1 Wireless Settings............................................................................................... 2038.6.2 Wireless Security............................................................................................... 2068.6.3 Wireless MAC Filtering ...................................................................................... 2088.6.4 Wireless Advanced ............................................................................................ 2108.6.5 Wireless Statistics...............................................................................................2118.7 DHCP ............................................................................................................................. 2128.7.1 DHCP Settings................................................................................................... 2128.7.2 DHCP Client List................................................................................................ 2138.7.3 Address Reservation ......................................................................................... 2148.8 USB Settings.................................................................................................................. 215
- VII -8.8.1 Storage Sharing................................................................................................. 2158.8.2 Media Server ..................................................................................................... 2178.8.3 User Accounts.................................................................................................... 2198.9 Forwarding ..................................................................................................................... 2208.9.1 Virtual Servers ................................................................................................... 2218.9.2 Port Triggering ................................................................................................... 2228.9.3 DMZ ................................................................................................................... 2248.9.4 UPnP ................................................................................................................. 2258.10 Security .......................................................................................................................... 2268.10.1 Basic Security.................................................................................................... 2268.10.2 Advanced Security............................................................................................. 2278.10.3 Local Management ............................................................................................ 2298.10.4 Remote Management ........................................................................................ 2308.11 Parental Control ............................................................................................................. 2318.12 Access Control............................................................................................................... 2338.12.1 Rule ................................................................................................................... 2338.12.2 Host ................................................................................................................... 2368.12.3 Target................................................................................................................. 2388.12.4 Schedule............................................................................................................ 2408.13 Advanced Routing.......................................................................................................... 2428.13.1 Static Routing List.............................................................................................. 2428.13.2 System Routing Table........................................................................................ 2438.14 Bandwidth Control.......................................................................................................... 2448.14.1 Control Settings ................................................................................................. 2448.14.2 Rule List............................................................................................................. 2448.15 IP & MAC Binding .......................................................................................................... 2468.15.1 Binding Setting .................................................................................................. 2468.15.2 ARP List............................................................................................................. 2488.16 Dynamic DNS................................................................................................................. 2488.16.1 No-IP DDNS ...................................................................................................... 2498.16.2 Comexe.cn DDNS ............................................................................................. 249
- VIII -8.16.3 Dyndns org DDNS ............................................................................................. 2508.17 System Tools.................................................................................................................. 2518.17.1 Time Settings..................................................................................................... 2528.17.2 Diagnostic.......................................................................................................... 2538.17.3 Firmware Upgrade............................................................................................. 2548.17.4 Factory Defaults................................................................................................. 2558.17.5 Backup & Restore.............................................................................................. 2568.17.6 Reboot ............................................................................................................... 2568.17.7 Password........................................................................................................... 2578.17.8 System Log........................................................................................................ 2588.17.9 Statistics............................................................................................................. 258Appendix A: FAQ .............................................................................................................................. 260Appendix B: Configuring the PC .................................................................................................... 265Appendix C: Specifications ............................................................................................................. 268Appendix D: Glossary...................................................................................................................... 269
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 1 -Package Contents The following items should be found in your package: ¾ One TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition ¾ Quick Installation Guide ¾ One RJ-45 Ethernet Cable ¾ One Resource CD for TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition, including: xUser Guide xOther Helpful Information )Note:Make sure that the package contains the above items. If any of the listed items is damaged or missing, please contact your distributor.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 2 - Chapter 1. Introduction1.1 Overview of the Router Small enough to fit in the average pocket, the TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition is uniquely suited to provide robust wireless networking to travelers, students, or anyone else for work or play. TL-WR710N supports the newest 802.11n standards, and provides backward compatibility with older 802.11b/g standards as well. The up-to-150Mbps wireless speed makes it ideal for handlingmultiple data streams at the same time, which ensures your network stable and smooth. The TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition supports five operation modes. Wireless Router mode creates an instant private wireless network and share Internet to multiple Wi-Fi devices, which is suitable for most hotel and home network. Access Point mode creates a wireless network for Wi-Fi devices. The wireless devices are exposed to the wired network. Repeater mode extends your home wireless range by copying the same wireless name and password. Client mode works as a wireless adapter for any Ethernet-enabled devices, such as Smart TV, Game Console and PC. WISP Client Router mode accesses the Internet wirelessly in areas with no wired ISP infrastructure With multiple protection measures, including SSID broadcast control and wireless LAN 64/128/152-bit WEP encryption, WiFi protected Access (WPA2-PSK, WPA-PSK), as well as advanced Firewall protections, the TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition provides complete data privacy. The TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition supports Virtual Server and DMZ host for Port Triggering, and then the network administrators can manage and monitor the network in real time with the remote management function. Since the Router is compatible with virtually all the major operating systems, it is very easy to manage. Quick Setup Wizard is supported and detailed instructions are provided step by step in Flexible Access Control Reliable Security ProtectionsIncredible Speed Multiple Operation Modes
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 3 - this user guide. Before installing the Router, please look through this guide to know all the Router’s functions. 1.2 ConventionsThe Router or TL-WR710N mentioned in this guide stands for TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition without any explanation. Parameters provided in the pictures are just references for setting up the product, which may differ from the actual situation. You can set the parameters according to your demand. 1.3 Main Features ¾Portable design, ideal for travel and home use ¾Built-in power supply design without external power adapter ¾Support Wireless Router, Access Point, Repeater, Client, WISP Client Router modes ¾USB port supports charging for smart phone and tablet ¾USB port supports storage sharing, media server function ¾Pre-encryption prevents unauthorized access from users outside of the network 1.4 Panel Layout Figure 1-1 TL-WR710N sketch
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 4 - ¾LEDStatus IndicationSolid Blue The device is working properly. BlinkingCondition 1: System is booting. Condition 2: The Ethernet Cable or USB Device is connecting to the product. Table 1-1 The LED Description ¾USB: The USB port connects to a USB storage device. ¾Reset˖It is used to reset the Router to its factory defaults. With the Router powered on, use a pin to press and hold the Reset button (about 5 seconds) until the SYS LED becomes quick-flash from slow-flash. And then release the button and wait the Router to reboot to its factory default settings. ¾LAN/WAN: This LAN/WAN port works as LAN in AP/Repeater/Client/WISP Client Router mode and as WAN in Wireless Router mode. As LAN, it connects the Router to the local PC; as WAN, it enables you connect the DSL/cable Modem, or Ethernet. ¾LAN:This LAN port works as LAN in Wireless Router/ AP/Repeater/Client/WISP Client Router mode. It connects the Router to the local PC.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 5 - Chapter 2. Connecting the Router 2.1System Requirements ¾Each PC in the LAN needs a working Ethernet Adapter ¾TCP/IP protocol must be installed on each PC ¾Web browser, such as Microsoft Internet Explorer 5.0 or later, Mozilla Firefox, Apple Safari ¾If the device is configured to Wireless Router/Access Point mode, you also need Broadband Internet Access Service (DSL/Cable/Ethernet) ¾One DSL/Cable Modem that has an RJ45 connector (which is not necessary if the Router is connected directly to the Ethernet.) 2.2 Installation Environment Requirements ¾Place the Router in a well-ventilated place far from any heater or heating vent ¾Place the Router in a location where it can be connected to the various devices as well as to a power source ¾Avoid direct irradiation of any strong light (such as sunlight) ¾Keep at least 2 inches (5 cm) of clear space around the Router ¾Operating Temperature: 0 ~40 (32 ~104 )ćḉ ̧¾Operating Humidity: 10%~90%RH, Non-condensing 2.3 Connecting the Router Before installing the Router, please make sure your broadband service provided by your ISP is available. If there is any problem, please contact with your ISP. To connect the Router, please follow the steps below: 1. Power off your PC, Cable/DSL Modem, and the Router. 2. Locate an optimum location for the Router. The best place is usually at the center of your wireless network. The place must accord with the Installation Environment Requirements.3. Plug the power plug in the electrical wall socket. The Router will start to work automatically. After finishing the steps above, please choose the operation mode you need and carry out the corresponding steps. There are five operation modes supported by this router: Wireless Router, Access Point, Repeater, Client and WISP Client Router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 6 - 2.3.1 Wireless Router Mode As a wireless router, TL-WR710N enables multi-user to share Internet via DSL/Cable Modem. The default mode of TL-WR710N is Wireless Router. On this mode, the wired port LAN/WAN works as WAN, it can be connected to DSL Modem or directly connected to a wired network with an Ethernet cable. Computers could connect to the device by both wired way through the wired port LAN and wireless way. Figure 2-1 Hardware Installation of the TL-WR710N in Router Mode 1. Connect the LAN/WAN port of TL-WR710N to the LAN Port on the DSL/Cable Modem. 2. Connect the WAN port on the DSL/Cable Modem to the wired Internet. 3. Plug the power plug of TL-WR710N in electrical wall socket. 4. Power on the DSL/Cable Modem, PC(s) and notebook(s). 2.3.2 Access Point Mode As the supplement of wired LAN, TL-WR710N enables the wired LAN to connect to the Internet wirelessly. Plug the power plug of TL-WR710N in electrical wall socket and connect the Ethernet cable correctly, you can surf the Internet by connecting your PC(s) to the Router wirelessly. On this mode, the wired port LAN/WAN works as LAN. Computer could connect to the device by either wired or wireless way. The Pre-encryption function is opened by default and the default password is the last unique eight numbers of each Router’s MAC address.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 7 - Figure 2-2 Hardware Installation of the TL-WR710N in AP Mode 1. Connect the LAN or LAN/WAN port of TL-WR710N to the wired network port with an Ethernet cable.2. Plug the power plug of TL-WR710N in electrical wall socket. 3. Power on the PC(s) and notebook(s). 2.3.3 Repeater Mode TL-WR710N is used to extend the range of wireless signal of the existing AP or wireless router. On this mode, the wired port LAN/WAN works as LAN. Computer could connect to the device by either wired or wireless way. The SSID of TL-WR710N should be the same as that of the device you repeat. Figure 2-3 Hardware Installation of the TL-WR710N in Repeater Mode 1. Plug the power plug of TL-WR710N in electrical wall socket.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 8 - 2. Power on the notebook(s). )Note:It is recommended that you connect a PC/notebook to the LAN port of the Router with an Ethernet cable, and then login the Router from the PC/notebook to set the Router in Repeater mode. 2.3.4 Client Mode TL-WR710N is used as a wireless network card to connect the wireless network signal or wireless router. On this mode, the wired port LAN/WAN works as LAN. Computer could connect to the device by either wired or wireless way. Figure 2-4 Hardware Installation of the TL-WR710N in Client Mode 1. Connect the PC to the LAN or LAN/WAN port of TL-WR710N router with an Ethernet cable. 2. Plug the power plug of TL-WR710N in electrical wall socket. 3. Power on the PC(s). 2.3.5 WISP Client Router Mode In WISP mode, TL-WR710N enables multiple users to share Internet connection from WISP. On this mode, the LAN port devices share the same IP from WISP through Wireless port. While connecting to WISP, the Wireless port works as a WAN port at WISP Client Router mode. The Ethernet port acts as a LAN port.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 9 - Figure 2-5 Hardware Installation of the TL-WR710N in WISP Client Router Mode 1. Plug the power plug of TL-WR710N in electrical wall socket. 2. Power on the notebook(s).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 10 - Chapter 3. Quick Installation Guide This chapter will show you how to configure the basic functions of your TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition using Quick Setup Wizard within minutes. 3.1 TCP/IP Configuration The default IP address of the TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition is 192.168.0.254. And the default Subnet Mask is 255.255.255.0. These values can be changed as you desire. In this guide, we use all the default values for description. Connect the local PC to the LAN port of the Router. And then you can configure the IP address for your PC as the following steps: 1) Set up the TCP/IP Protocol in "Obtain an IP address automatically" mode on your PC. If you need instructions as to how to do this, please refer to Appendix B: "Configuring the PC”.2) Then the built-in DHCP server will assign IP address for the PC. Then connect to the Router through wireless connection following the steps below: 1) Click the icon at the bottom of your desktop. Click refresh button, and then select the default SSID of the Router. Click Connect.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 11 - 2) Enter the Security key. Click OK.3) If you can see Connected after the default SSID, you’ve successfully connected to the wireless network. )Note: 1. The default SSID and Password of your Router are on the label. Both are case-sensitive. 2. The pre-encryption function is enabled by default and the default Network key/Security keyis the Password on the label. Now, you can run the Ping command in the command prompt to verify the network connection between your PC and the Router. The following example is in Windows XP. Open a command prompt, and type ping 192.168.0.254, and then press Enter.¾ If the result displayed is similar to the Figure 3-1, it means the connection between your PC and the Router has been established well.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 12 - Figure 3-1 Success result of Ping command ¾ If the result displayed is similar to the Figure 3-2, it means the connection between your PC and the Router has failed. Figure 3-2 Failure result of Ping command Please check the connection following these steps: 1. Is the connection between your PC and the Router correct? )Note: The LED of LAN/WAN ports which you link to on the Router should be lit.2. Is the TCP/IP configuration for your PC correct? )Note:If the Router's IP address is 192.168.0.254, your PC's IP address must be within the range of 192.168.0.1 ~ 192.168.0.253.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 13 - 3.2 Quick Installation Guide With a Web-based utility, it is easy to configure and manage the TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition. The Web-based utility can be used on any Windows, Macintosh or UNIX OS with a Web browser, such as Microsoft Internet Explorer, Mozilla Firefox or Apple Safari. 1. To access the configuration utility, open a web-browser and type in the default address http://tplinklogin.net in the address field of the browser. After a moment, a login window will appear, similar to the Figure 3-3. Enter admin for the User Name and Password, both in lower case letters. Then click the OK button or press the Enter key. Figure 3-3 Login Windows )Note:If the above screen does not pop-up, it means that your Web-browser has been set to a proxy. Go to Tools menu>Internet Options>Connections>LAN Settings, in the screen that appears, cancel the Using Proxy checkbox, and click OK to finish it.2. After a successful login, you can click the Quick Setup menu to quickly configure your Router. Figure 3-4 Quick Setup 3. Click Next, and then Working Mode page will appear, shown in Figure 3-5.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 14 - Figure 3-5 Quick Setup - Working Mode )Note:The Router supports five working modes for multi-user to access the Internet: Wireless Router,Access Point,Repeater,Client and WISP Client Router. In Wireless Router mode, the device enables multiple users to share the Internet connection via ADSL/Cable Modem. In Access Pointmode, this device can be connected to a wired network and transform the wired access into wireless that multiple devices can share together. In Repeater mode, the device will relay data to an associated root AP. In Client mode, the device will act as a wireless station to enable wired host(s) to access AP. In WISP Client Router mode, the device enables multiple users to share Internet connection from WISP. You can configure your device quickly by the following steps in different modes. 3.2.1 Wireless Router Mode When you choose Wireless Router on Working Mode page in Figure 3-5 , take the following steps: 1. Click Next in Figure 3-5, and then WAN Connection Type page will appear as shown in Figure 3-6.Figure 3-6 Quick Setup - WAN Connection Type
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 15 - The Router supports three popular ways PPPoE,Dynamic IP and Static IP to connect to the Internet. To make sure the connection type your ISP provides, please refer to the ISP. Make sure the cable is securely plugged into the WAN port before detection. ¾Auto Detect - If you don't know the connection type your ISP provides, use this option to allow the Quick Setup to search your Internet connection for servers and protocols and determine your ISP configuration.¾PPPoE - For this connection, you will need your account name and password from your ISP.If you have applied ADSL to realize Dial-up service, you should choose this type. Under this condition, you should fill in both the User Name and Password that the ISP supplied. Please note that these fields are case-sensitive.Figure 3-7 Quick Setup - PPPoE ¾Dynamic IP - Your ISP uses a DHCP service to assign your Router an IP address for connecting to the Internet. When the Router connects to a DHCP server, or the ISP supplies you with DHCP connection, please choose this type. If you choose this type of connection, no configuration should be set and you can go on with the wireless configuration in Figure 3-9.¾Static IP - This type of connection uses a permanent, fixed (static) IP address that your ISP assigned. In this type, you should fill in the IP address, Subnet Mask, Default Gateway, and DNS IP address manually, which are specified by your ISP. Then click Next and proceed to Figure 3-9. Figure 3-8 Quick Setup - Static IP
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 16 - 2. Then, the Wireless page will appear as shown in Figure 3-9. Set the wireless parameters. It is recommended that you rename an SSID, choose a Security Type and enter a Password. Then click Next.Figure 3-9 Quick Setup - Wireless ¾Wireless Radio - Enable or disable the wireless radio choosing from the pull-down list. ¾Wireless Network Name - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test.¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.¾Mode - Select the desired mode. The default setting is 11bgn mixed. x11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.x11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition-17-When 11bg mixed mode is selected, only 11bg mixed wireless stations can connect tothe Router. It is strongly recommended that you set the Mode to 11bgn mixed, and all of802.11b/g/n wireless stations can connect to the Router.Note:If 11bgmixed mode is selected in the Mode field, the Channel Widthselecting field will turngrey and the value will become 20M, which is unable to be changed.Channel Width-Select any channel width from the pull-down list. The default setting isautomatic, which can automatically adjust the channel width for your clients.Channel - This field determines which operating frequency will be used. The defaultchannel is set to Auto . It is not necessary to change the wireless channel unless younotice interference problems with another nearby access point.Wireless Security-You can configure the security settings of your wireless network.Disable Security-The wireless security function can be enabled or disabled. Ifdisabled, the wireless stations will be able to connect the Router without encryption.WPA-PSK/WPA2-PSK - Input the password of your broadcast SSID.No Change- If you chose this option, wireless security configuration will not change.3. The Finishpage is shown as Figure 3-10. Click the Reboot button to make your wirelessconfiguration take effect and finish the Quick Setup .Figure 3-10 Quick Setup – Finish3.2.2 Access Point Mode When you choose Access Point on WorkingMode page in Figure 3-5 , take the following steps:1. Click Nextin Figure 3-5, and then W irelesspage will appear as shown in Figure 3-11.Limited by local law,the country code and channel 12-13 can not be selected in the USA.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 18 - Figure 3-11 Quick Setup - Wireless ¾Wireless Network Name - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, TEST is NOT the same as test.¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.¾Channel - This field determines which operating frequency will be used. The default channel is set to Auto. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. ¾Mode - Select the desired mode. The default setting is 11bgn mixed.x11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.x11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. When 11bg mixed mode is selected, only 11bg mixed wireless stations can connect to the Router. It is strongly recommended that you set the Mode to 11bgn mixed, and all of 802.11b/g/n wireless stations can connect to the Router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 19 - )Note:If 11bg mixed mode is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed. ¾Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can automatically adjust the channel width for your clients. ¾Wireless Security Mode - This option should be chosen according to the security configuration of the AP you want to access. It is recommended that the security type is the same as your AP’s security type.¾Wireless Password - Input the password of your broadcast SSID. 2. Click the Next button. You will then see the Finish page. If you don’t make any change on the Wireless page, you will see the Finish page as shown in Figure 3-12. Click the Finish button to finish the Quick Setup.Figure 3-12 Quick Setup - Finish If there is something changed on the Wireless page, you will see the Finish page as shown in Figure 3-13. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup.Figure 3-13 Quick Setup – Finish 3.2.3 Repeater Mode When you choose Repeater Mode on Working Mode page in Figure 3-5 , take the following steps: 1. Click Next, and then Wireless Repeater page will appear as shown in Figure 3-14.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 20 - Figure 3-14 Quick Setup - Wireless ¾Repeater Mode - In Repeater mode, the wireless repeater relays signal between its stations and the root AP for greater wireless range.xUniversal Repeater - In Repeater mode, the AP with WDS disabled will relay data to an associated root AP. AP function is enabled meanwhile.xWDS Repeater - In WDS Repeater mode, the AP with WDS enabled will relay data to an associated root AP. AP function is enabled meanwhile.¾Wireless Name of Root AP - The SSID of AP that you want to access.¾MAC Address of Root AP - The MAC address of AP that you want to access.¾Survey - Click this button, you can search the AP which runs in the environment.¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.¾Wireless Security Mode - This option should be chosen according to the security configuration of the AP you want to access. It is recommended that the security type is the same as your AP’s security type.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 21 - ¾Wireless Password - If the AP your router is going to connect need password, you need to fill the password in this blank. 2. Click Survey button on the Wireless page as shown in Figure 3-14, and then AP List page will appear as shown in Figure 3-15. Find the SSID of the Access Point you want to access, and click Connect in the corresponding row. For example, the third item is selected. The target network’s SSID will be automatically filled into the corresponding box which is shown as the Figure 3-14. Figure 3-15 AP List )Note:If you know the SSID of the desired AP, you can also input it into the field "SSID" manually. 3. Click the Next button in Figure 3-14. You will then see the Finish page.Because something has changed on the Wireless Repeater page, you will see the Finishpage as shown in Figure 3-16. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup.Figure 3-16 Quick Setup - Finish 3.2.4 Client Mode When you choose Client on Working Mode page in Figure 3-5 , take the following steps: 1. Click Nextin Figure 3-5, and then Wireless Client page will appear as shown in Figure 3-17.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 22 - Figure 3-17 Quick Setup - Wireless ¾Wireless Name of Root AP - Enter the SSID that you want to access. ¾MAC Address of Root AP - Enter the MAC address of AP that you want to access. ¾Survey - Click this button, you can survey the AP which runs in the environment. ¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.¾Wireless Security Mode - This option should be chosen according to the security configuration of the AP you want to access. It is recommended that the security type is the same as your AP’s security type. ¾Wireless Password - If the AP your router is going to connect need password, you need to fill the password in this blank. 2. Click Survey button on the Wireless page as shown in Figure 3-17, and then AP List page will appear as shown in Figure 3-18. Find the SSID of the Access Point you want to access, and click Connect in the corresponding row. For example, the third item is selected. The target network’s SSID will be automatically filled into the corresponding box which is shown as the Figure 3-17.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 23 - Figure 3-18 AP List 3. Click the Next button in Figure 3-19. You will then see the Finish page. Click the Rebootbutton to make your wireless configuration take effect and finish the Quick Setup.Figure 3-19 Quick Setup - Finish 3.2.5 WISP Client Router Mode When you choose WISP Client Router Mode on Working Mode page in Figure 3-5 , take the following steps: 1. Click Next, and then WAN Connection Type page will appear as shown in Figure 3-20. Figure 3-20 Quick Setup – WAN Connection Type The Router supports three popular ways PPPoE,Dynamic IP and Static IP to connect to the Internet. To make sure the connection type your ISP provides, please refer to the ISP. Make sure the cable is securely plugged into the WAN port before detection.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 24 - ¾PPPoE - For this connection, you will need your account name and password from your ISP.If you have applied ADSL to realize Dial-up service, you should choose this type. Under this condition, you should fill in both the User Name and Password that the ISP supplied. Please note that these fields are case-sensitive.Figure 3-21 Quick Setup - PPPoE ¾Dynamic IP - Your ISP uses a DHCP service to assign your Router an IP address for connecting to the Internet. When the Router connects to a DHCP server, or the ISP supplies you with DHCP connection, please choose this type. If you choose this type of connection, no configuration should be set and you can go on with the wireless configuration in Figure 3-23.¾Static IP - This type of connection uses a permanent, fixed (static) IP address that your ISP assigned. In this type, you should fill in the IP address, Subnet Mask, Default Gateway, and DNS IP address manually, which are specified by your ISP. Then click Next and proceed to Figure 3-23. Figure 3-22 Quick Setup - Static IP 2. You can configure the basic settings for the wireless network on this page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 25 - Figure 3-23 Quick Setup - Static IP ¾SSID - The SSID of the AP your router is going to connect to as a client. You can also use the search function to select the SSID to join. ¾BSSID - The BSSID of the AP your router is going to connect to as a client. You can also use the search function to select the BSSID to join. ¾Survey - Click this button, you can survey the AP which runs in the current channel. ¾Key type - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type. ¾WEP Index - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the index of the WEP key. ¾Auth type - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX).It indicates the authorization type of the Root AP. ¾Password - If the AP your router is going to connect needs password, you need to fill the password in this blank. ¾Local SSID - Enter a value of up to 32 characters. The same Name (SSID) must be assigned to all wireless devices in your network.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 26 - ¾Wireless Security Mode - You can configure the security settings of your wireless network.¾Wireless Password - Input the password of your Local SSID. 3. Click Survey button on the Wireless page as shown in Figure 3-20, and then AP List page will appear as shown in Figure 3-24. Find the SSID of the Access Point you want to access, and click Connect in the corresponding row. For example, the third item is selected. The target network’s SSID will be automatically filled into the corresponding box which is shown as the Figure 3-20. Then click Next.Figure 3-24 AP List 4. The Finish page is shown as Figure 3-25. Click the Reboot button to make your wireless configuration take effect and finish the Quick Setup.Figure 3-25 Quick Setup – Finish )Note:The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. zNear the center of the area in which your wireless stations will operate. zIn an elevated location such as a high shelf. zAway from the potential sources of interference, such as PCs, microwaves, and cordless phones. zAway from large metal surfaces. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 27 - Chapter 4. Configuration for Wireless Router Mode This chapter will show each Web page's key functions and the configuration way for Wireless Router Mode of TL-WR710N. 4.1LoginAfter your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions. Figure 4-1 The detailed explanations for each Web page’s key function are listed below. 4.2 Status The Status page provides the current status information about the Router on Wireless Router Mode. All information is read-only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 28 - Figure 4-2 ¾Firmware Version - The version information of the Router’s firmware. ¾Hardware Version - The version information of the Router’s hardware. ¾LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. xMAC Address - The physical address of the Router, as seen from the LAN. xIP Address - The LAN IP address of the Router. xSubnet Mask - The subnet mask associated with LAN IP address.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 29 - ¾Wireless - This field displays basic information or status for wireless function, you can configure them in the Wireless > Wireless Settings page. xWorking Mode - The current wireless working mode in use. xWireless Radio - Indicates whether the wireless radio feature of the AP is enabled or disabled.xName (SSID) - The SSID of the AP. xMode - The current wireless mode which the Router works on. xChannel Width - The current wireless channel width in use. xChannel - The current wireless channel in use. xMAC Address - The physical address of the Router, as seen from the WLAN. xWDS Status - The status of WDS connection. ¾WAN - This field displays the current settings or information for the WAN, you can configure them in the Network > WAN page.xMAC Address - The physical address of the WAN port, as seen from the Internet. xIP Address - The current WAN (Internet) IP Address. This field will be blank or 0.0.0.0 if the IP Address is assigned dynamically and there is no connection to the Internet. xSubnet Mask - The subnet mask associated with the WAN IP Address. xDefault Gateway - The Gateway currently used by the Router is shown here. When you use Dynamic IP as the connection Internet type, the Renew button will be displayed here. Click the Renew Button to obtain new IP parameters dynamically from the ISP. And if you have got an IP address, Release button will be displayed here. Click the Release button to release the IP address the Router has obtained from the ISP. ¾DNS Server - The DNS (Domain Name System) server IP addresses currently used by the Router.¾Traffic Statistics - The Router’s traffic statistics.xReceived (Bytes) - Traffic that counted in bytes has been received out from the WAN port. xReceived (Packets) - Traffic that counted in packets has been received out from the WAN port.xSent (Bytes) - Traffic that counted in bytes has been sent out from the WAN port. xSent (Packets) - Traffic that counted in packets has been sent out from the WAN port. ¾System Up Time-The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 30 - 4.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide."4.4 WPSWPS (Wi-Fi Protected Setup) can help you to quickly and securely connect to a network. This section will guide you to add a new wireless device to an existing network quickly by function. The WPS function is only available when the Operation Mode is set to Access Point. Select menu “WPS”, you will see the next screen shown in Figure 4-3. Figure 4-3 WPS ¾WPS Status - To enable or disable the WPS function here. ¾Current PIN - The current value of the device's PIN is displayed here. The default PIN of the device can be found in the label or User Guide. ¾Restore PIN - Restore the PIN of the device to its default. ¾Gen New PIN - Click this button, and then you can get a new random value for the device's PIN. You can ensure the network security by generating a new PIN. ¾Disable PIN of this Device - WPS external registrar of entering the device’s PIN can be disabled or enabled manually. If the device receives multiple failed attempts to authenticate an external Registrar, this function will be disabled automatically.¾Add Device - You can add a new device to the existing network manually by clicking this button.To add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and device using either Push Button Configuration (PBC) method or PIN method.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 31 - )Note:To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile. For the configuration of the new device, here takes the Wireless Adapter of our company for example.I. By PBC If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Method One: Step 1: Keep the WPS Status as Enabled and click the Add Device button in Figure 4-3, then the following screen will appear. Figure 4-4 Add A New Device Step 2: Choose “Press the button of the new device in two minutes” and click Connect.Step 3: For the configuration of the wireless adapter, please choose “Push the button on my access point or wireless router” in the configuration utility of the WPS as below, and click Connect.The WPS Configuration Screen of Wireless Adapter
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 32 - Step 4: Wait for a while until the next screen appears. Click OK to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter Method Two: Enter the PIN into my AP Step 1: For the configuration of the wireless adapter, please choose “Enter the PIN of this device into my access point or wireless router” in the configuration utility of the WPS as below, and click Connect. The WPS Configuration Screen of Wireless Adapter )Note:In this example, the default PIN code of this adapter is 16952898 as the above figure shown.Step 2: Keep the WPS Status as Enabled and click the Add Device button in Figure 4-3.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 33 - Step 3: Choose “Enter the new device's PIN” and enter the PIN code ˄take 16952898 for example˅ of the wireless adapter in the field after PIN as shown in the figure below. Then click Connect.Figure 4-5 Add A New DeviceMethod Three: Enter the PIN from my AP Step 1: Get the Current PIN code of the AP in Figure 4-3 (each AP has its unique PIN code. Here takes the PIN code 12345670 of this AP for example). Step 2: For the configuration of the wireless adapter, please choose “Enter the PIN of my access point or wireless router” in the configuration utility of the WPS as below, and enter the PIN code of the AP into the field after “Access Point PIN”. Then click Connect.The WPS Configuration Screen of Wireless Adapter )Note:The default PIN code of the AP can be found in its label or the WPS configuration screen as Figure 4-3.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 34 - You will see the following screen when the new device has successfully connected to the network. Figure 4-6 )Note:1) The WPS LED on the AP will light green for five minutes if the device has been successfully added to the network.2) The WPS function cannot be configured if the Wireless function of the AP is disabled. Please make sure the Wireless function is enabled before configuring the WPS. 4.5 Working Mode The Router supports five operation mode types: Wireless Router,Access Point, Repeater, Client and Wireless Client Router. Please select one you want. Click Save to save your choice, which is shown as Figure 4-7. Figure 4-7 Wireless Working Mode Settings ¾Wireless Router - The wireless Router Mode. In this mode, the device enables multi-user to share Internet via DSL/Cable Modem. The only wired port works as WAN. ¾Access Point - The wireless access point mode. ¾Repeater - The wireless Repeater Mode. It could extend the range of wireless network. ¾Client - The Client Mode. The computer connected by Ethernet could get access to an AP by Client mode.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 35 - ¾WISP Client Router - In this mode, the device enables multiple users to share Internet connection from WISP. 4.6 NetworkFigure 4-8 the Network menu There are three submenus under the Network menu (shown in Figure 4-8): WAN,MAC Cloneand LAN.Click any of them, and you will be able to configure the corresponding function. 4.6.1 WANChoose menu “Network ė WAN”, and then you can configure the IP parameters of the WAN on the screen below. 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will automatically get IP parameters from your ISP. You can see the page as follow (Figure 4-9): Figure 4-9 WAN – Dynamic IPThis page displays the WAN IP parameters assigned dynamically by your ISP, including IP address,Subnet Mask,Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 36 - ¾MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Sizeunless required by your ISP. ¾Use These DNS Servers - If your ISP gives you one or two DNS addresses, select UseThese DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP. )Note:If you find error when you go to a website after entering the DNS addresses, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses. ¾Host Name - This option specifies the Host Name of the Router. ¾Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP Address normally, you can choose this option. (It is rarely required.) Click the Save button to save your settings. 2. If your ISP provides a static or fixed IP Address,Subnet Mask,Default Gateway and DNSsetting, select Static IP. The Static IP settings page will appear as shown in Figure 4-10. Figure 4-10 WAN - Static IP¾IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ¾Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. ¾Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your ISP.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 37 - ¾MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Sizeunless required by your ISP. ¾Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. Click the Save button to save your settings. 3. If your ISP provides a PPPoE connection, select PPPoE/Russia PPPoE option. Then you should enter the following parameters (Figure 4-11): Figure 4-11 WAN – PPPoE/Russia PPPoE¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Confirm Password - Enter again the Password provided by your ISP to ensure the password you entered is correct. ¾Secondary Connection - It’s available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection.xDisabled - The Secondary Connection is disabled by default, so there is PPPoE connection only. This is recommended.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 38 - xDynamic IP - You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP. xStatic IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP. ¾Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects. ¾Connect Automatically - The connection can be re-established automatically when it was down. ¾Time-based Connecting - The connection will only be established in the period from the start time to the end time (both are in HH:MM format). )Note:Only when you have configured the system time on “System Tools ĺ Time” page, will the Time-based Connecting function can take effect. ¾Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automaticallyafter a specified inactivity period and re-established when you attempt to access the Internet again. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Caution: Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. If you want to do some advanced configurations, please click the Advanced button, and the page shown in Figure 4-12 will then appear:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 39 - Figure 4-12 PPPoE Advanced Settings ¾MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ¾Service Name/AC Name - The service name and AC (Access Concentrator) name should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work. ¾ISP Specified IP Address - If your ISP does not automatically assign IP addresses to the Router during login, please click “Use IP address specified by ISP” check box and enter the IP address provided by your ISP in dotted-decimal notation.¾Detect Online Interval - The Router will detect Access Concentrator online at every interval. The default value is “0”. You can input the value between “0” and “120”. The value “0” means no detect. ¾Primary DNS/Secondary DNS - If your ISP does not automatically assign DNS addresses to the Router during login, please click “Use the following DNS servers”check box and enter the IP address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it as well. Click the Save button to save your settings. 4. If your ISP provides BigPond Cable connection, please select BigPond Cable option. Then you should enter the following parameters (Figure 4-13):
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 40 - Figure 4-13 WAN – BigPond Cable ¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Auth Server - Enter the authenticating server IP address or host name. ¾Auth Domain - Type in the domain suffix server name based on your location, ¾MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ¾Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects. ¾Connect Automatically - The connection can be re-established automatically when it was down. ¾Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automatically
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 41 - after a specified inactivity period and re-established when you attempt to access the Internet again. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Caution: Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. Click the Save button to save your settings. 5. If your ISP provides L2TP connection, please select L2TP/Russia L2TP option. Then you should enter the following parameters (Figure 4-14): Figure 4-14 WAN – L2TP/Russia L2TP¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connectbutton to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 42 - ¾Connect on Demand - You can configure the Router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, check the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. ¾Connect Automatically - Connect automatically after the Router is disconnected. To use this option, check the radio button. ¾Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, check the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number of minutes that you wish to have the Internet connecting last unless a new link is requested. Caution: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, because some applications are visiting the Internet continually in the background. Click the Save button to save your settings. 6. If your ISP provides PPTP connection, please select PPTP/Russia PPTP option. And you should enter the following parameters (Figure 4-15):
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 43 - Figure 4-15 WAN – PPTP/Russia PPTP ¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. ¾Connect on Demand - You can configure the Router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, check the radio button. If you want your Internet connection to remain active at all times, enter “0” in the Max
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 44 - Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. ¾Connect Automatically - Connect automatically after the Router is disconnected. To use this option, check the radio button. ¾Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested. Caution: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. Click the Save button to save your settings. 4.6.2 MAC Clone Choose menu “Network ė MAC Clone”, and then you can configure the WAN MAC address on the screen below, as shown in Figure 4-16: Figure 4-16 MAC Address CloneSome ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. ¾WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format (X is any hexadecimal digit). ¾Your PC's MAC Address - This field displays the MAC address of the PC that is managing the Router. If the MAC address is required, you can click the Clone MAC Address Tobutton and this MAC address will fill in the WAN MAC Address field. Click Restore Factory MAC to restore the MAC address of WAN port to the factory default value.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 45 - Click the Save button to save your settings. )Note:1. Only the PC on your LAN can use the MAC Address Clone function. 2. If you change WAN MAC Address when the WAN connection is PPPoE, it will not take effect until the connection is re-established. 4.6.3 LANChoose menu “Network ė LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 4-17 LAN ¾MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed. ¾IP Address - Enter the IP address of your Router in dotted-decimal notation (factory default: 192.168.0.254). ¾Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. ¾IGMP Proxy - The Internet Group Management Protocol (IGMP) feature allows your devices in LAN can watch TV. )Note:1. If you change the IP Address of LAN, you must use the new IP Address to login to the Router. 2. If the new LAN IP Address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automaticallyˈwhile the Virtual Server and DMZ Host will not take effect until they are re-configured.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 46 - 4.7 Wireless Figure 4-18 Wireless menu There are five submenus under the Wireless menu (shown in Figure 4-18): Wireless Settings,Wireless Security, Wireless MAC Filtering, Wireless Advanced and Wireless Statistics. Clickany of them, and you will be able to configure the corresponding function. 4.7.1 Wireless Settings Choose menu “Wireless ė Wireless Settings”, and then you can configure the basic settings for the wireless network on this page. Figure 4-19 Wireless Settings - Router ¾Wireless Network Name - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, TESTis NOT the same as test.¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 47 - the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. ¾Mode - Select the desired mode. The default setting is 11bgn mixed. x11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.x11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients. When 11bg mixed mode is selected, only 11bg mixed wireless stations can connect to the Router. It is strongly recommended that you set the Mode to 11bgn mixed, and all of 802.11b/g/n wireless stations can connect to the Router. )Note:If 11bg mixed mode is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed. ¾Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can automatically adjust the channel width for your clients. ¾Channel - This field determines which operating frequency will be used. The default channel is set to Auto. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. ¾Enable Wireless Router Radio - The wireless radio of the Router can be enabled or disabled to allow wireless stations access. If enabled, the wireless stations will be able to access the Router. Otherwise, wireless stations will not be able to access the Router. ¾Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the wireless router will broadcast its name (SSID) on the air. ¾Enable WDS - You can select to enable WDS. With this function, the Router can bridge two or more WLANs. If this checkbox is selected, you will have to set the following parameters as shown below. Make sure the following settings are correct.Figure 4-20 Wireless Settings – WDS Bridging ¾SSID (to be bridged) - The SSID of the AP your Router is going to connect to as a client. You can also use the search function to select the SSID to join.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 48 - ¾BSSID (to be bridged) - The BSSID of the AP your Router is going to connect to as a client. You can also use the search function to select the BSSID to join. ¾Survey - Click this button, you can survey the AP which runs in the current channel. ¾Security Options - This option should be chosen according to the AP's security configuration. It is recommended that the security type is the same as your AP's security type.¾WEP Index-This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the index of the WEP key. ¾Auth Type - This option should be chosen if the key type is WEP (ASCII) or WEP (HEX). It indicates the authorization type of the Root AP. ¾Password - If the AP your Router is going to connect needs password, you need to fill the password in this blank.Be sure to click the Save button to save your settings on this page. )Note:1. The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. zNear the center of the area in which your wireless stations will operate. zIn an elevated location such as a high shelf. zAway from the potential sources of interference, such as PCs, microwaves, and cordless phones. zAway from large metal surfaces. 2. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. 4.7.2 Wireless Security Choose menu “Wireless ė Wireless Security”, and then you can configure the security settings of your wireless network. There are three wireless security modes supported by the Router: WPA/WPA2-Personal, WPA/WPA2-Enterprise and WEP (Wired Equivalent Privacy).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 49 - Figure 4-21 Wireless Security ¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. ¾WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.xVersion- you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic, which can selectWPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. xEncryption-When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. )Note:If you check the WPA-PSK/WPA2-PSK radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 4-22.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 50 - Figure 4-22 ¾WPA /WPA2-Enterprise - It’s based on Radius Server. xVersion- you can choose the version of the WPA security from the pull-down list. The default setting is Automatic, which can selectWPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. xEncryption -You can select Automatic,TKIP or AES.xRadius Server IP - Enter the IP address of the Radius server.xRadius Port - Enter the port that Radius server used. xRadius Password - Enter the password for the Radius server. xGroup Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. ¾WEP - It is based on the IEEE 802.11 standard. xType - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can selectShared Keyor Open Systemauthentication type automatically based on the wireless station's capability and request. xWEP Key Format-Hexadecimal andASCII formats are provided here.Hexadecimalformat stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length.xWEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. xKey Type- You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit -You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 51 - 152-bit - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 16 ASCII characters. )Note:If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. Be sure to click the Save button to save your settings on this page. 4.7.3 Wireless MAC Filtering Choose menu “Wireless ė Wireless MAC Filtering”, and then you can control the wireless access by configuring the Wireless MAC Filtering function, as shown in Figure 4-23. Figure 4-23 Wireless MAC Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disable.¾MAC Address - The wireless station's MAC address that you want to access. ¾Status - The status of this entry, either Enabled or Disable.¾Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 4-24: Figure 4-24 Add or Modify Wireless MAC Address Filtering entry
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 52 - To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B. 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3. Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to save this entry. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page. Click the Previous button to return to the previous page. For example: If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the Router, but all the other wireless stations cannot access the Router, you can configure the Wireless MAC Address Filtering list by following these steps: 1. Click the Enabled button to enable this function. 2. Select the radio button “Allow the stations specified by any enabled entries in the list to access” for Filtering Rules.3. Delete all or disable all entries if there are any entries already. 4. Click theAdd New...button. 1) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. 2) Enter wireless station A/B in the Description field. 3) Select Enabled in the Status pull-down list. 4) Click the Save button. 5) Click the Back button. The filtering rules that configured should be similar to the following list:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 53 - Figure 4-25 Filtering Rules 4.7.4 Wireless Advanced Choose menu “Wireless ė Wireless Advanced”, and then you can configure the advanced settings of your wireless network. Figure 4-26 Wireless Advanced ¾Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. ¾RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346.¾Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. ¾DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 54 - broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. ¾Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended enabled. ¾Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time.¾Enable AP Isolation - This function isolate all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled.)Note:If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 4.7.5 Wireless Statistics Choose menu “Wireless ė Wireless Statistics”, and then you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 4-27 Wireless Statistics ¾MAC Address - The connected wireless station's MAC address ¾Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected¾Received Packets - Packets received by the station ¾Sent Packets - Packets sent by the station. ¾Configure - The button is used for loading the item to the Wireless MAC Filtering list. xAllow - If the Wireless MAC Filtering function enable, allow the station to access.xDeny - If the Wireless MAC Filtering function enable, deny the station to access.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 55 - You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. )Note:This page will be refreshed automatically every 5 seconds. 4.8 DHCP Figure 4-28 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 4-28), DHCP Settings,DHCP Clients List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 4.8.1 DHCP Settings Choose menu “DHCP ė DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure 4-29. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router on the LAN. Figure 4-29 DHCP Settings ¾DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 56 - ¾Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. ¾End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. ¾Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ¾Default Gateway (Optional) -It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.0.254. ¾Default Domain (Optional) - Input the domain name of your network. ¾Primary DNS - (Optional) Input the DNS IP address provided by your ISP or consult your ISP. Or consult your ISP. ¾Secondary DNS (Optional) -Input the IP address of another DNS server if your ISP provides two DNS servers. )Note:To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 4.8.2 DHCP Client List Choose menu “DHCP ė DHCP Client List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 4-30. Figure 4-30 DHCP Client List ¾Client Name-The name of the DHCP client ¾MAC Address - The MAC address of the DHCP client ¾Assigned IP - The IP address that the Router has allocated to the DHCP client ¾Lease Time- The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 57 - You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 4.8.3 Address Reservation Choose menu “DHCP ė Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 4-31).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 4-31 Address Reservation ¾MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾Reserved IP Address - The IP address reserved for the PC by the Router. ¾Status - The status of this entry, either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To Reserve an IP address:1. Click the Add New… button. Then will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 4-32 Add or Modify an Address Reservation Entry To modify or delete an existing entry:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 58 - 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page.4.9 USB Settings Figure 4-33 The USB Settings menu There are three submenus under the USB Settings menu (shown in Figure 4-33), Storage Sharing,Media Server and User Accounts. Click any of them, and you will be able to configure the corresponding functions. 4.9.1 Storage Sharing Choose menu “USB SettingsėStorage Sharing”, you can configure a USB disk drive attached to the router and view volume and share such properties as share name, capacity, used space, and free space on this page as shown below. Figure 4-34 Storage Sharing ¾Service Status - Indicates the Network Sharing service's current status. You can click the Start button to start the Storage Sharing service and click the Stop button to stop it.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 59 - ¾Volume - The volume name of the USB drive the users have access to. Volume 1-8 is mapping to USB port1, and Volume 9-16 is mapping to USB port2. ¾Capacity - The storage capacity of the USB driver. ¾Used - The used space of the USB driver. ¾Free - The available space of the USB driver. ¾Use% - The percentage of the used space. ¾Shared - Indicates the shared or non-shared status of the volume. When the volume is shared, you can click the Disable to stop sharing the volume; when volume is non-shared, you can click the Enable button to share the volume. Click the Start button to start the Network Sharing service. Click the Stop button to stop the Network Sharing service. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. This takes the drive offline. A message (as shown in Figure 4-35) will appear on your web browser when it is safe to detach the USB disk. Figure 4-35 Safe Unplug Message Click the Rescan button to start a new scan. Follow the instructions below to set up your router as a file server: 1. Plug an external USB hard disk drive or USB flash drive into this router. 2. Click the Rescan button to find the USB drive that has been attached to the router. 3. Click the Start button to start the Storage Sharing service. 4. Click the Enable button under Shared to enable the disk to share. 5. Click the Open the disk to visit the sharing disk. )Note:1. The router can automatically locate new USB drive. But to display the information about your USB device, you need to click the Rescan button manually. 2. The new settings will not take effect until you restart the service.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 60 - 3. To unplug the USB drive, click Eject Disk button first. Simply pulling USB drive out of the USB port can cause damage to the device and loss of data. 4. Mounted volumes of each USB port are subject to the 8-volume limit. So you cannot access more than 8 volumes on the USB storage device. 5. If you change the storage settings during the storage connection is established, then the changes will not take effect until the router or the client is rebooted. 4.9.2 Media Server Choose menu “USB SettingsėMedia Server”, you can create media server that allows you to share stored content with other computers and devices on your home network and on the Internet. Figure 4-36 Media Server Setting ¾Server Name - The name of this Media Server. ¾Server Status - Indicates the Media Server’s current status, started or stopped. You can click the Start button to start the Media Server and click the Stop button to stop it. ¾Name - The display name of this folder. ¾File System - The file system type on the partition can be FAT32 or NTFS. ¾Folder - The real full path of the specified folder. ¾Delete - You can delete the share folder by click Delete.To set up your media server, please follow the instructions below: 1. Plug an external USB hard disk drive or USB flash drive into this router, and then the screen will appear as shown in Figure 4-37. Figure 4-37 Media Server Setting
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 61 - 2. Click the Start button to start the media server, and then the screen will appear as shown in Figure 4-38. Figure 4-38 Media Server Setting 3. Click the Add share folder button to specify a folder as the search path of media server. The screen will then appear as shown in Figure 4-39. Figure 4-39 Add New Folder ¾Display Name - You can enter a display name for the share folder. ¾Share entire partition - Choose this option and then the folders contained in this partition will all be shared. ¾Folder Location- Displays the location of this folder. ¾Select - Check the radio button to select the folder to share. ¾Folder - Displays folders that are in current path. ¾Upper - Click this button to get into the upper folder. ¾Save - Click this button to save your settings and the page will be redirected to the media server configuration page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 62 - ¾Back - Click this button to discard the settings and just go to the media server configuration page. 4. Click the Scan All button to scan all the share folders immediately. You can also select the Auto-scan, at same time, select an auto scan interval time by drop-down list. In this case, the media server will auto scan the share folders. )Note:The max share folders number is 6. If you want share a new folder when the number has been reached to be 6, you can delete a share folder and then add a new one. 4.9.3 User Accounts You can specify the user name and password for Storage Sharing users on this page. Storage Sharing users can use Internet Explorer to access files on the USB drive. There are two default user accounts that can access the Storage Sharing. They are Administrator and Guest (as shown in Figure 4-40). Administrator has read/write access to Storage Sharing and can access FTP Server while Guest has read-only access to Storage Sharing and cannot access FTP Server. Figure 4-40 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive. To add a new user account, please follow the steps below: 1. Click Add New User button, and the screen will appear as shown in Figure 4-41. 2. Self-define a User Name.3. Enter the password in the Password field. 4. Choose the Storage Authority from the drop-down list, Read and Write or Read Only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 63 - Figure 4-41 Add or Modify User Account ¾User Name - Type the user name that you want to give access to the USB drive. The user name must be composed of alphanumeric symbols not exceeding 15 characters in length.¾Password - Enter the password in the Password field. The password must be composed of alphanumeric symbols not exceeding 15 characters in length. For security purposes, the password for each user account is not displayed. ¾Storage Authority – Choose Read and Write or Read Only from the drop-down list to assign access authority of Storage Sharing to the user.¾Save - You can click the Save button to save your settings.¾Back - You can click the Back button to discard the settings and just go to the media server configuration page. )Note:Please restart the service for the new settings to take effect. If you cannot use the new user name and password to access the shares, press Windows logo + Rto open the Run dialog box and type net use \\192.168.0.254 /delete /yes and press Enter. (192.168.0.254 is your router's LAN IP address. If the LAN IP of the modem connected with your router is 192.168.1.x, the default LAN IP of the router will automatically switch from 192.168.0.254 to 192.168.1.254 to avoid IP conflict; in this case, please try net use \\192.168.1.254 /delete / yes.)4.10Forwarding Figure 4-42 The Forwarding menu
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 64 - There are four submenus under the Forwarding menu (shown in Figure 4-42): Virtual Servers,Port Triggering,DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 4.10.1 Virtual Servers Choose menu “Forwarding ė Virtual Servers”, and then you can view and add virtual servers in the screen as shown in Figure 4-43. Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP. A virtual server is defined as a service port, and all requests from the Internet to this service port will be redirected to the computer specified by the server IP. Any PC that was used for a virtual server must have a static or reserved IP Address because its IP Address may be changed when using the DHCP function. Figure 4-43 Virtual Servers ¾Service Port - The numbers of External Ports. You can type a service port or a range of service ports (in XXX – YYY format, XXX is the start port number, YYY is the end port number). ¾Internal Port - The Internal Service Port number of the PC running the service application. You can leave it blank if the Internal Port is the same as the Service Port, or enter a specific port number when Service Port is a single one. ¾IP Address - The IP Address of the PC providing the service application. ¾Protocol - The protocol used for this application, either TCP,UDP, or All (all protocols supported by the Router). ¾Status - The status of this entry, either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To setup a virtual server entry: 1. Click the Add New… button, the next screen will pop-up as shown in Figure 4-44. 2. Select the service port you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the service port number or service port range in the Service Port box. 3. Type the IP Address of the computer in the IP Address box.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 65 - 4. Select the protocol used for this application, either TCP,UDP, or All.5. Select the Enabled to enable the virtual server. 6. Click the Save button. Figure 4-44 Add or Modify a Virtual Server Entry )Note:If your computer or server has more than one type of available service, please select another service, and enter the same IP Address for that computer or server. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and click the Previous button to return the previous page.)Note:If you set the service port of the virtual server as 80, you must set the Web management port on “Security ė Remote Management” page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 4.10.2 Port Triggering Choose menu “Forwarding ė Port Triggering”, and then you can view and add port triggering in the screen as shown in Figure 4-45. Some applications require multiple connections, like Internet games, video conferencing, Internet calling and so on. These applications cannot work
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 66 - with a pure NAT Router. Port Triggering is used for some of these applications that can work with an NAT Router. Figure 4-45 Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. 2. The Router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3. When necessaryˈ the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field.¾Trigger Port - The port for outgoing traffic. An outgoing connection using this port will trigger this rule. ¾Trigger Protocol - The protocol used for Trigger Ports, either TCP,UDP, or All (all protocols supported by the Router). ¾Incoming Ports - The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. You can input at most 5 groups of ports (or port sections). Every group of ports must be set apart with ",". For example, 2000-2038, 2050-2051, 2085, 3010-3030. ¾Incoming Protocol - The protocol used for Incoming Ports Range, either TCP or UDP, or ALL (all protocols supported by the Router). ¾Status - The status of this entry, either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To add a new rule, follow the steps below: 1. Click the Add New… button, the next screen will pop-up as shown in Figure 4-46. 2. Select a common application from the Common Applications drop-down list, then the Trigger Port field and the Incoming Ports field will be automatically filled. If the CommonApplications do not have the application you need, enter the Trigger Port and the Incoming Ports manually. 3. Select the protocol used for Trigger Port from the Trigger Protocol drop-down list, either TCP,UDP, or All.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 67 - 4. Select the protocol used for Incoming Ports from the Incoming Protocol drop-down list, either TCP or UDP, or All.5. Select Enabled in Status field. 6. Click the Save button to save the new rule. Figure 4-46 Add or Modify a Port Triggering Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled. Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries. )Note:1. When the trigger connection is released, the corresponding opening ports will be closed. 2. Each rule is allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused. 3. Incoming Port Range cannot overlap each other. 4.10.3 DMZChoose menu “Forwarding ė DMZ”, and then you can view and configure DMZ host in the screen as shown in Figure 4-47. The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. DMZ host forwards all the ports at the same time. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may be changed when using the DHCP function.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 68 - Figure 4-47 DMZ To assign a computer or server to be a DMZ server: 1. Check the Enable radio button. 2. Enter the IP Address of a local host in the DMZ Host IP Address field. 3. Click the Save button. )Note:After you set the DMZ host, the firewall related to the host will not work.4.10.4 UPnPChoose menu “Forwarding ė UPnP”, and then you can view the information about UPnP (Universal Plug and Play) in the screen as shown in Figure 4-48. The UPnP feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. Figure 4-48 UPnP ¾Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disablebutton.¾Current UPnP Settings List - This table displays the current UPnP information.xApp Description - The description provided by the application in the UPnP request. xExternal Port - The external port the Router opens for the application. xProtocol - The type of protocol the Router opens for the application. xInternal Port - The Internal port the Router opens for local host. xIP Address - The IP address of the UPnP device that is currently accessing the Router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 69 - xStatus - The status of the port is displayed here. “Enabled” means that the port is still active. Otherwise, the port is inactive. Click Refresh to update the Current UPnP Settings List. 4.11SecurityFigure 4-49 The Security menu There are four submenus under the Security menu as shown in Figure 4-49: Basic Security,Advanced Security, Local Management and Remote Management. Click any of them, and you will be able to configure the corresponding function. 4.11.1 Basic Security Choose menu “Security ė Basic Security”, you can configure the basic security in the screen as shown in Figure 4-50. Figure 4-50 Basic Security ¾Firewall - A firewall protects your network from the outside world. Here you can enable or disable the Router’s firewall. zSPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 70 - traffic passing through the session conforms to the protocol. SPI Firewall is enabled by factory default. If you want all the computers on the LAN exposed to the outside world, you can disable it. ¾VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall.zPPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Router, keep the default, Enable.zL2TP Passthrough - Layer 2 Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default, Enable.zIPSec Passthrough - Internet Protocol Security (IPSec) is a suite of protocols for ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services. To allow IPSec tunnels to pass through the Router, keep the default, Enable.¾ALG - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, TFTP, H323 etc. zFTP ALG - To allow FTP clients and servers to transfer data across NAT, keep the default Enable.zTFTP ALG - To allow TFTP clients and servers to transfer data across NAT, keep the default Enable.zH323 ALG - To allow Microsoft NetMeeting clients to communicate across NAT, keep the default Enable.Click the Save button to save your settings. 4.11.2 Advanced Security Choose menu “Security ė Advanced Security”, you can protect the Router from being attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood in the screen as shown in Figure 4-51.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 71 - Figure 4-51 Advanced Security ¾Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. ¾DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled. )Note:Dos Protection will take effect only when the Traffic Statistics in “System Tool ė Traffic Statistics” is enabled. ¾Enable ICMP-FLOOD Attack Filtering- Enable or Disable the ICMP-FLOOD Attack Filtering.¾ICMP-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current ICMP-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately. ¾Enable UDP-FLOOD Filtering- Enable or Disable the UDP-FLOOD Filtering. ¾UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 72 - ¾Enable TCP-SYN-FLOOD Attack Filtering- Enable or Disable the TCP-SYN-FLOOD Attack Filtering. ¾TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current TCP-SYN-FLOOD Packets numbers is beyond the set value, the Router will startup the blocking function immediately. ¾Ignore Ping Packet From WAN Port - Enable or Disable Ignore Ping Packet From WAN Port. The default setting is disabled. If enabled, the ping packet from the Internet cannot access the Router. ¾Forbid Ping Packet From LAN Port - Enable or Disable Forbid Ping Packet From LAN Port. The default setting is disabled. If enabled, the ping packet from LAN cannot access the Router. This function can be used to defend against some viruses. Click the Save button to save the settings. Click the Blocked DoS Host List button to display the DoS host table by blocking.4.11.3 Local Management Choose menu “Security ė Local Management”, you can configure the management rule in the screen as shown in Figure 4-52. The management feature allows you to deny computers in LAN from accessing the Router. Figure 4-52 Local Management By default, the radio button “All the PCs on the LAN are allowed to access the Router's Web-Based Utility” is checked. If you want to allow PCs with specific MAC Addresses to access the Setup page of the Router's Web-Based Utility locally from inside the network, check the radio button “Only the PCs listed can browse the built-in web pages to perform Administrator tasks”, and then enter each MAC Address in a separate field. The format for the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). Only the PCs with MAC address listed can
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 73 - use the password to browse the built-in web pages to perform Administrator tasks while all the others will be blocked. After click the Add button, your PC's MAC Address will be placed in the list above. Click the Save button to save your settings. )Note:If your PC is blocked but you want to access the Router again, press and hold the WPS button for more than 5 seconds to reset the Router to factory defaults. 4.11.4Remote Management You can configure the Remote Management function on this page. This feature allows you to manage your Router from a remote location, via the Internet. Figure 4-53 Remote Management ¾Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router’s default remote management Web port number is 80. For greater security, you can change the remote management Web interface to a custom port by entering that number in this box provided. Choose a number between 1024 and 65535, but do not use the number of any common service port. ¾Remote Management IP Address - This is the current address you will use when accessing your router from the Internet. The default IP Address is 0.0.0.0. It means this function is disabled. To enable this function, change the default IP Address to another IP Address as desired. To access the router, you will type your router's WAN IP Address into your browser's Address (in IE) or Location (in Navigator) box, followed by a colon and the custom port number. For example, if your Router's WAN address is 202.96.12.8 and you use port number 8080, enter in your browser: http://202.96.12.8:8080. You will be asked for the router's password. After successfully entering the password, you will be able to access the router's Web-based utility. )Note:Be sure to change the router's default password to a very secure password.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 74 - 4.12Parental Control Choose menu “Parental Control”, and you can configure the parental control in the screen as shown in Figure 4-54. The Parental Control function can be used to control the internet activities of the child, limit the child to access certain websites and restrict the time of surfing. Figure 4-54 Parental Control Settings ¾Parental Control - Check Enable if you want this function to take effect, otherwise check Disable.¾MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below. ¾MAC Address of Your PC - This field displays the MAC address of the PC that is managing this Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above. ¾Website Description - Description of the allowed website for the PC controlled. ¾Schedule - The time period allowed for the PC controlled to access the Internet. For detailed information, please go to “Access Controlė Schedule”.¾Modify - Here you can edit or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New… button and the next screen will pop-up as shown in Figure 4-55. 2. Enter the MAC address of the PC (e.g. 00-11-22-33-44-AA) you’d like to control in the MAC Address of Child PC field. Or you can choose the MAC address from the All Address in Current LAN drop-down list. 3. Give a description (e.g. Allow Google) for the website allowed to be accessed in the Website Description field.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 75 - 4. Enter the allowed domain name of the website, either the full name or the keywords (e.g. google) in the Allowed Domain Name field. Any domain name with keywords in it (e.g.www.google.com) will be allowed. 5. Select from the Effective Time drop-down list the schedule (e.g. Schedule_1) you want the entry to take effect. If there are not suitable schedules for you, click the Schedule in red below to go to the Advance Schedule Settings page and create the schedule you need. 6. In the Status field, you can select Enabled or Disabled to enable or disable your entry. 7. Click the Save button. Click the Enable All button to enable all the rules in the list. Click the Disable All button to disable all the rules in the list. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 4-55 Add or Modify Parental Control Entry For example: If you desire that the child PC with MAC address 00-11-22-33-44-AA can access www.google.com on Saturday only while the parent PC with MAC address 00-11-22-33-44-BB is without any restriction, you should follow the settings below. 1. Click “Parental Control” menu on the left to enter the Parental Control Settings page. Check Enable and enter the MAC address 00-11-22-33-44-BB in the MAC Address of Parental PC field.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 76 - 2. Click “Access Restriction ĺ Schedule” on the left to enter the Schedule Settings page. Click Add New... button to create a new schedule with Schedule Description is Schedule_1, Day is Sat and Time is all day-24 hours. 3. Click “Parental Control” menu on the left to go back to the Add or Modify Parental Control Entry page: zClick Add New... button. zEnter 00-11-22-33-44-AA in the MAC Address of Child PC field. zEnter “Allow Google” in the Website Description field. zEnter “www.google.com” in the Allowed Domain Name field. zSelect “Schedule_1” you create just now from the Effective Time drop-down list. zIn Status field, select Enable. 4. Click Save to complete the settings. Then you will go back to the Parental Control Settings page and see the following list, as shown in Figure 4-56. Figure 4-56 4.13 Access Control Figure 4-57 The Access Control menu There are four submenus under the Access Restriction menu as shown in Figure 4-57: Rule,Host,Target and Schedule. Click any of them, and you will be able to configure the corresponding function. 4.13.1 RuleChoose menu “Access Controlė Rule”, you can view and set Access Restriction rules in the screen as shown in Figure 4-58.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 77 - Figure 4-58 Access Control Rule Management ¾Enable Internet Access Control - Select the check box to enable the Internet Access Restriction function, so the Default Filter Policy can take effect. ¾Rule Name - Here displays the name of the rule and this name is unique. ¾Host - Here displays the host selected in the corresponding rule. ¾Target - Here displays the target selected in the corresponding rule. ¾Schedule - Here displays the schedule selected in the corresponding rule. ¾Action - Here displays the action the Router takes to deal with the packets. It could be Allowor Deny.Allow means that the Router permits the packets to go through the Router. Denymeans that the Router rejects the packets to go through the Router. ¾Status - This field displays the status of the rule. Enabled means the rule will take effect, Disabled means the rule will not take effect. ¾Modify - Here you can edit or delete an existing rule. To add a new rule, please follow the steps below. 1. Click the Add New… button and the next screen will pop-up as shown in Figure 4-59. 2. Give a name (e.g. Rule_1) for the rule in the Rule Name field.3. Select a host from the Host drop-down list or choose “Click Here To Add New Host List”.4. Select a target from the Target drop-sown list or choose “Click Here To Add New Target List”.5. Select a schedule from the Schedule drop-down list or choose “Click Here To Add New Schedule”.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 78 - 6. In the Action field, select Deny or Allow.7. In the Status field, select Enabled or Disabled to enable or disable your entry. 8. Click the Save button. Click the Enable All button to enable all the rules in the list. Click the Disable All button to disable all the rules in the list. Click the Delete All button to delete all the entries in the table. You can change the entry’s order as desired. Fore entries are before hind entries. Enter the ID number in the first box you want to move and another ID number in second box you want to move to, and then click the Move button to change the entry’s order. Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 4-59 Add or Modify Internet Access Restriction Entry For example: If you desire to allow the host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, and forbid other hosts in the LAN to access the Internet, you should follow the settings below: 1. Click “Access Control ė Host” in the left to enter the Host Settings page. Add a new entry with the Host Description is Host_1 and MAC Address is 00-11-22-33-44-AA. 2. Click “Access Control ė Target” in the left to enter the Target Settings page. Add a new entry with the Target Description is Target_1 and Domain Name is www.google.com. 3. Click “Access Control ė Schedule” in the left to enter the Schedule Settings page. Add a new entry with the Schedule Description is Schedule_1, Day is Sat and Sun, Start Time is 1800 and Stop Time is 2000. 4. Click “Access Control ė Rule” in the left to return to the Access Restriction Rule Management page. Select “Enable Internet Access Restriction” and choose "Deny the packets not specified by any access Restriction policy to pass through the Router". 5. Click Add New... button to add a new rule as follows:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 79 - zIn Rule Name field, create a name for the rule. Note that this name should be unique, for example Rule_1. zIn Host field, select Host_1. zIn Target field, select Target_1. zIn Schedule field, select Schedule_1. zIn Action field, select Allow. zIn Status field, select Enabled. zClick Save to complete the settings. Then you will go back to the Access Restriction Rule Management page and see the following list. Figure 4-60 Rule Settings 4.13.2 HostChoose menu “Access Control ė Host”, you can view and set a Host list in the screen as shown in Figure 4-61. The host list is necessary for the Access Restriction Rule. Figure 4-61 Host Settings ¾Host Description - Here displays the description of the host and this description is unique. ¾Information - Here displays the information about the host. It can be IP or MAC. ¾Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New… button. 2. In the Mode field, select IP Address or MAC Address. zIf you select IP Address, the screen shown is Figure 4-62. 1) In Host Description field, create a unique description for the host (e.g. Host_1).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 80 - 2) In LAN IP Address field, enter the IP address. zIf you select MAC Address, the screen shown is Figure 4-63. 1) In Host Description field, create a unique description for the host (e.g. Host_1). 2) In MAC Address field, enter the MAC address. 3. Click the Save button to complete the settings. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page. Figure 4-62 Add or Modify a Host Entry Figure 4-63 Add or Modify a Host Entry For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA, you should first follow the settings below: 1. Click Add New... button in Figure 4-61 to enter the Add or Modify a Host Entry page. 2. In Mode field, select MAC Address from the drop-down list. 3. In Host Description field, create a unique description for the host (e.g. Host_1). 4. In MAC Address field, enter 00-11-22-33-44-AA. 5. Click Save to complete the settings. Then you will go back to the Host Settings page and see the following list.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 81 - Figure 4-64 Host Settings 4.13.3 Target Choose menu “Access Control ė Target”, you can view and set a Target list in the screen as shown in Figure 4-65. The target list is necessary for the Access Restriction Rule. Figure 4-65 Target Settings ¾Target Description - Here displays the description about the target and this description is unique.¾Information - The target can be IP address, port, or domain name. ¾Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below.1. Click the Add New… button. 2. In Mode field, select IP Address or Domain Name. zIf you select IP Address, the screen shown is Figure 4-66. 1) In Target Description field, create a unique description for the target (e.g. Target_1). 2) In IP Address field, enter the IP address of the target. 3) Select a common service from Common Service Port drop-down list, so that the Target Port will be automatically filled. If the Common Service Port drop-down list doesn’t have the service you want, specify the Target Port manually. 4) In Protocol field, select TCP, UDP, ICMP or ALL.zIf you select Domain Name, the screen shown is Figure 4-67. 1) In Target Description field, create a unique description for the target (e.g. Target_1).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 82 - 2) In Domain Name field, enter the domain name, either the full name or the keywords (for example Google) in the blank. Any domain name with keywords in it (e.g.www.google.com) will be blocked or allowed. You can enter 4 domain names. 3. Click the Save button. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page. Figure 4-66 Add or Modify an Access Target Entry Figure 4-67 Add or Modify an Access Target Entry For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA in the LAN to access www.google.com only, you should first follow the settings below: 1. Click Add New… button in Figure 4-65 to enter the Add or Modify an Access Target Entry page.2. In Mode field, select Domain Name from the drop-down list. 3. In Target Description field, create a unique description for the target (e.g. Target_1). 4. In Domain Name field, enter www.google.com. 5. Click Save to complete the settings.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 83 - Then you will go back to the Target Settings page and see the following list, Figure 4-68 Target Settings 4.13.4ScheduleChoose menu “Access Control ė Schedule”, you can view and set a Schedule list in the next screen as shown in Figure 4-69. The Schedule list is necessary for the Access Restriction Rule. Figure 4-69 Schedule Settings ¾Schedule Description - Here displays the description of the schedule and this description is unique.¾Day - Here displays the day(s) in a week. ¾Time - Here displays the time period in a day. ¾Modify - Here you can edit or delete an existing schedule. To add a new schedule, follow the steps below. 1. Click Add New... button shown in Figure 4-69 and the next screen will pop-up as shown in Figure 4-70. 2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Day field, select the day or days you need. 4. In Time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5. Click Save to complete the settings. Click the Delete All button to delete all the entries in the table.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 84 - Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 4-70 Advanced Schedule Settings For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday andSunday, you should first follow the settings below: 1. Click Add New... button shown in Figure 4-69 to enter the Advanced Schedule Settings page.2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Day field, check the Select Days radio button and then select Sat and Sun. 4. In Time field, enter 1800 in Start Time field and 2000 in Stop Time field. 5. Click Save to complete the settings. Then you will go back to the Schedule Settings page and see the following list. Figure 4-71 Schedule Settings
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 85 - 4.14 Advanced Routing Figure 4-72 The Advanced Routing Menu There are two submenus under the Network menu (shown in Figure 4-72): Static Routing Listand SystemRouting Table. Click any of them, and you will be able to configure the corresponding function. 4.14.1 Static Routing List Choose menu “Static Routing”, and you can configure the static route in the next screen, shown in Figure 4-73. A static route is a pre-determined path that network information must travel to reach a specific host or network. Figure 4-73 Static Routing To add static routing entries, follow the steps below. 1. Click Add New… shown in Figure 4-73, you will see the following screen Figure 4-74. Figure 4-74 Add or Modify a Static Route Entry 2. Enter the following data. ¾Destination Network - The Destination IP Address is the address of the network or host that you want to assign to a static route.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 86 - ¾Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion. ¾Default Gateway- This is the IP Address of the gateway device that allows for contact between the Router and the network or host. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to make the entry take effect. Click the Delete button to delete the entry. Click the Enable All button to enable all the entries. Click the Disable All button to disable all the entries. Click the Delete All button to delete all the entries. Click the Previous button to view the information in the previous screen, click the Nextbutton to view the information in the next screen. 4.14.2 System Routing Table Choose menu “Advanced Routing ė System Routing Table”, and you can views all of the valid route entries in use. The Destination IP address, Subnet Mask, Gateway, and Interface will be displayed for each entry. Figure 4-75 Routing Table ¾Destination Network - The Destination IP Address is the address of the network or host to which the static route is assigned. ¾Subnet Mask - The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion. ¾Gateway - This is the IP address of the gateway device that allows for contact between the Router and the network or host. ¾Interface - This interface tells you whether the Destination IP Address is on the LAN & WLAN (internal wired and wireless networks), the WAN (Internet).Click the Refresh button to refresh the data displayed.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 87 - 4.15Bandwidth Control Figure 4-76 The Bandwidth Control menu There are two submenus under the Bandwidth Control menu as shown in Figure 4-76. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.15.1 Control Settings Choose menu “Bandwidth Control ė Control Settings”, you can configure the Egress Bandwidth and Ingress Bandwidth in the next screen. Their values you configure should be less than 100000Kbps. For optimal control of the bandwidth, please select the right Line Type and ask your ISP for the total bandwidth of the egress and ingress.Figure 4-77 Bandwidth Control Settings ¾Enable Bandwidth Control - Check this box so that the Bandwidth Control settings can take effect.¾Line Type - Select the right type for you network connection. If you don’t know how to choose, please ask your ISP for the information.¾Egress Bandwidth - The upload speed through the WAN port.¾Ingress Bandwidth - The download speed through the WAN port.4.15.2 Rule List Choose menu “Bandwidth Control ė Rule List”, you can view and configure the Bandwidth Control rules in the screen below.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 88 - Figure 4-78 Bandwidth Control Rule List ¾Description - This is the information about the rules such as address range.¾Egress Bandwidth - This field displays the max and mix upload bandwidth through the WAN port, the default is 0. ¾Ingress Bandwidth - This field displays the max and mix download bandwidth through the WAN port, the default is 0. ¾Enable - This displays the status of the rule. ¾Modify - Click Modify to edit the rule. Click Delete to delete the rule. To add/modify a Bandwidth Control rule, follow the steps below. Step 1: Click Add New… shown in Figure 4-78, you will see a new screen shown in Figure 4-79. Step 2: Enter the information like the screen shown below. Figure 4-79 Bandwidth Control Rule Settings ¾Enable - Enable or disable the rule. ¾IP Range - Interior PC address range. If both are blank (or 0.0.0.0), the domain is no effective. ¾Port Range - The port range which the Interior PC access the outside PC. If all are blank (or 0), the domain is no effective. ¾Protocol - Transport layer protocol, here there are All, TCP, UDP.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 89 - ¾Egress Bandwidth - The max and the min upload speed which through the WAN port, default number is 0. ¾Ingress Bandwidth - The max and the min download speed through the WAN port, default number is 0. Step 3: Click the Save button. 4.16 IP & MAC Binding Figure 4-80 The IP & MAC Binding menu There are two submenus under the IP & MAC Binding menu: Binding Setting and ARP List.Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 4.16.1 Binding Setting This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire.Figure 4-81 IP & MAC Binding Setting ¾MAC Address - The MAC address of the controlled computer in the LAN. ¾IP Address - The assigned IP address of the controlled computer in the LAN. ¾Bind - Whether or not enable the ARP binding. ¾Modify - Edit or delete item.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 90 - When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Modify button, and then you will go to the next page. This page is used for adding or modifying an IP & MAC Binding entry. Figure 4-82 IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries: 1. Click the Add New.. button. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. To modify or delete an existing entry:1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column. To find an existing entry:1. Click the Find button (shown in Figure 4-81). 2. Enter the MAC Address or IP Address. 3. Enter the Find button in the next page (shown in Figure 4-83). Figure 4-83 Find IP & MAC Binding Entry
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 91 - Click the Enable All button to make all entries enabled. Click the Delete All button to delete all entries. 4.16.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entries.Figure 4-84 ARP List ¾MAC Address - The MAC address of the controlled computer in the LAN. ¾IP Address - The assigned IP address of the controlled computer in the LAN. ¾Status - Enabled or Disabled of the MAC address and IP address binding. ¾Configure - Load or delete item. ¾Load - Load the item to the IP & MAC Binding list. ¾Delete - Delete the item. Click the Bind All button to bind all the current items, available after enable. Click the Load All button to load all items to the IP & MAC Binding list. Click the Refresh button to refresh all items. )Note:An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been loaded before. Error warning will prompt as well. Likewise, "Load All" only loads the items without interference to the IP & MAC Binding list. 4.17 Dynamic DNS The Router offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 92 - dynamic IP address, and then your friends can connect to your server by entering your domain name no matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as www.no-ip.com,www.comexe.cn, or www.dyndns.org. The Dynamic DNS client service provider will give you a password or key. 4.17.1 No-IP DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear as shown in Figure 4-85. Figure 4-85 No-IP DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to log in the DDNS service. Connection Status - The status of the DDNS service connection is displayed here. Click Logout to log out the DDNS service. )Note:If you want to login again with another account after a successful login, please click the Logoutbutton, then input your new username and password and click the Login button. 4.17.2 Comexe.cn DDNS If the dynamic DNS Service Provider you select is www.comexe.cn, the page will appear as shown in Figure 4-86.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 93 - Figure 4-86 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your dynamic DNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service. 4.17.3Dyndns org DDNS If the dynamic DNS Service Provider you select is www.dyndns.org, the page will appear as shown in Figure 4-87.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 94 - Figure 4-87 Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider here. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service. 4.18 System Tools Figure 4-88 The System Tools menu There are nine submenus under the System Tools menu: Time Settings,Diagnostic,Firmware Upgrade,Factory Defaults, Backup and Restore, Reboot, Password, System Log and
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 95 - Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 4.18.1Time Settings You can set time manually or get GMT from the Internet for the router on this page: Figure 4-89 Time Settings ¾Time Zone - Select your local time zone from this pull-down list. ¾Date - Enter your local date in MM/DD/YY into the right blanks. ¾Time - Enter your local time in HH/MM/SS into the right blanks. To set time manually, follow the steps below: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save.For automatic time synchronization: 1. Enter the address of the NTP Server 1 or NTP Server 2.2. Click the Get GMT button to get GMT time from Internet if you have connected to Internet. )Note:This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully, if not, the time limited on these functions will not take effect. ¾The time will be lost if the router is turned off.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 96 - ¾The router will obtain GMT automatically from Internet if it has already connected to Internet. 4.18.2 DiagnosticChoose menu “System Tools ė Diagnostic”, you can transact Ping or Traceroute function to check connectivity of your network in the following screen. Figure 4-90 Diagnostic Tools ¾Diagnostic Tool - Check the radio button to select one diagnostic too. xPing - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. xTraceroute - This diagnostic tool tests the performance of a connection.)Note:You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries. ¾IP Address/Domain Name - Type the destination IP address (such as 202.108.22.5) or Domain name (such as www.baidu.com). ¾Pings Count - The number of Ping packets for a Ping connection. ¾Ping Packet Size - The size of Ping packet.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 97 - ¾Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. ¾Traceroute Max TTL - The max number of hops for a Traceroute connection.Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 4-91 Diagnostic Results )Note:Only one user can use this tool at one time. "Ping Count", "Ping Packet Size" and "Ping Timeout" are Ping Parameters. "Traceroute Max TTL" is Traceroute Parameter. 4.18.3Firmware Upgrade The page allows you to upgrade the latest version firmware to keep your router up-to-date. Figure 4-92 Firmware Upgrade New firmware is posted at www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to upgrade firmware, unless the new firmware supports a new feature you need.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 98 - )Note:1. When you upgrade the router's firmware, you will lose current configuration settings, so make sure you backup the router’s settings before you upgrade its firmware. 2. Make sure that your computer is connected to the Internet through the cable when you upgrade the firmware. To upgrade through wireless connection is not allowed. 3. Set your IP address as static IP before upgrading. To upgrade the router's firmware, follow these instructions: 1. Download the latest firmware upgrade file from our website 2http://www.tp-link.com.2. Enter or select the path name where you save the downloaded file on the computer into the File blank. 3. Click the Upgrade button. ¾Firmware Version - Displays the current firmware version. ¾Hardware Version - Displays the current hardware version. The hardware version of the upgrade file must accord with the current hardware version. )Note:The firmware version must correspond to the hardware. The upgrade process takes a few minutes and the Router will restart automatically when the upgrade is completed. It is important to keep power on during the entire process. Loss of power during the upgrade could damage the Router. 4.18.4Factory Defaults This page allows you to restore the factory default settings for the router. Figure 4-93 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. ¾The default User Name: admin ¾The default Password: admin ¾The default access: tplinklogin.net )Note:Any settings you have saved will be lost when the default settings are restored.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 99 - 4.18.5 Backup & Restore This page allows you to save current configuration of router as backup or restore the configuration file you saved before. Figure 4-94 Backup & Restore Configuration ¾Click the Backup button to save all configuration settings as a backup file in your local computer. ¾To restore the router's configuration, follow these instructions: xClick the Browse button to select the backup file which you want to restore. xClick the Restore button. )Note:The current configuration will be covered with the uploading configuration file. The restoration process lasts for 20 seconds and the router will restart automatically. Keep the router on during the restoring process to prevent any damage. 4.18.6 RebootThis page allows you to reboot the router. Figure 4-95 Reboot the router Click the Reboot button to reboot the router. Some settings of the router will take effect only after rebooting, which include:¾Change LAN IP Address. (System will reboot automatically) ¾MAC Clone (system will reboot automatically) ¾DHCP service function. ¾Static address assignment of DHCP server.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 100 - ¾Web Service Port of the router. ¾Upgrade the firmware of the router (system will reboot automatically). ¾Restore the router's settings to factory default (system will reboot automatically). 4.18.7 Password This page allows you to change the factory default user name and password of the router. Figure 4-96 Password It is recommended strongly that you change the factory default user name and password of the router. All users who try to access the router's Web-based utility or Quick Setup will be prompted )Note:The new user name and password must not exceed 14 characters in length and must not include any spaces. Enter the new Password twice to confirm it. Click the Save button when finished. Click the Clear All button to clear all. 4.18.8System Log This page allows you to query the logs of the router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 101 - Figure 4-97 System Log ¾Refresh - Refresh the page to show the latest log list. ¾Save Log - Click to save all the logs in a txt file. ¾Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the later log soon. ¾Clear Log - All the logs will be deleted from this device permanently, not just from the page. 4.18.9 StatisticsThe Statistics page displays the network traffic of each PC in LAN, including total traffic and traffic of the last Packets Statistic interval seconds.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 102 - Figure 4-98 Statistics ¾Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will be ineffective. ¾Packets Statistics Interval - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval indicates the time section of the packets statistic. ¾Sorted Rules - Here displays sort as desired. Statistics Table: IP Address The IP Address displayed with statistics Packets The total amount of packets received and transmitted by the router. Total Bytes The total amount of bytes received and transmitted by the router. Packets The total amount of packets received and transmitted in the lastPackets Statistic interval seconds. Bytes The total amount of bytes received and transmitted in the last Packets Statistic interval seconds. ICMP Tx The total amount of the ICMP packets transmitted to WAN in the last Packets Statistic interval seconds. UDP Tx The total amount of the UDP packets transmitted to WAN in the last Packets Statistic interval seconds. CurrentTCP SYN Tx The total amount of the TCP SYN packets transmitted to WAN in the last Packets Statistic interval seconds. Click the Save button to save the Packets Statistic interval value. Click the Auto-refresh checkbox to refresh automatically. Click the Refresh button to refresh immediately.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 103 - Chapter 5. Configuration for Access Point Mode This chapter will show each Web page's key functions and the configuration way for Access Point Mode of TL-WR710N. 5.1LoginAfter your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions. Figure 5-1 The detailed explanations for each Web page’s key function are listed below. 5.2 Status The Status page provides the current status information about the Router on Access Point Mode. All information is read-only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 104 - Figure 5-2 Status ¾Firmware Version - The version information of the Router’s firmware. ¾Hardware Version - The version information of the Router’s hardware. ¾Wired - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. xMAC address - The physical address of the Router, as seen from the LAN. xIP address - The LAN IP address of the Router. xSubnet Mask - The subnet mask associated with LAN IP address. ¾Wireless - This field displays basic information or status for wireless function, you can configure them in the Wireless > Wireless Settings page. xWorking Mode - The current wireless working mode in use. xWireless Network Name - The SSID of the AP. xChannel - The current wireless channel in use. xMode - The current wireless mode which the Router works on.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 105 - xChannel Width - The current wireless channel width in use. xMAC Address - The physical address of the Router, as seen from the WLAN. ¾Traffic Statistics - The Router’s traffic statistics.xReceived (Bytes) - Traffic that counted in bytes has been received out from the WAN port. xReceived (Packets) - Traffic that counted in packets has been received out from the WAN port.xSent (Bytes) - Traffic that counted in bytes has been sent out from the WAN port. xSent (Packets) - Traffic that counted in packets has been sent out from the WAN port. ¾System Up Time-The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 5.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide."5.4 WPSWPS (Wi-Fi Protected Setup) can help you to quickly and securely connect to a network. This section will guide you to add a new wireless device to an existing network quickly by function. The WPS function is only available when the Operation Mode is set to Access Point. Select menu “WPS”, you will see the next screen shown in Figure 5-3. Figure 5-3 WPS ¾WPS Status - To enable or disable the WPS function here. ¾Current PIN - The current value of the device's PIN is displayed here. The default PIN of the device can be found in the label or User Guide. ¾Restore PIN - Restore the PIN of the device to its default. ¾Gen New PIN - Click this button, and then you can get a new random value for the device's PIN. You can ensure the network security by generating a new PIN.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 106 - ¾Disable PIN of this Device - WPS external registrar of entering the device’s PIN can be disabled or enabled manually. If the device receives multiple failed attempts to authenticate an external Registrar, this function will be disabled automatically.¾Add Device - You can add a new device to the existing network manually by clicking this button.To add a new device: If the wireless adapter supports Wi-Fi Protected Setup (WPS), you can establish a wireless connection between wireless adapter and device using either Push Button Configuration (PBC) method or PIN method. )Note:To build a successful connection by WPS, you should also do the corresponding configuration of the new device for WPS function meanwhile. For the configuration of the new device, here takes the Wireless Adapter of our company for example.II. By PBC If the wireless adapter supports Wi-Fi Protected Setup and the Push Button Configuration (PBC) method, you can add it to the network by PBC with the following two methods. Method One: Step 1: Keep the WPS Status as Enabled and click the Add Device button in Figure 5-3, then the following screen will appear. Figure 5-4 Add A New Device Step 2: Choose “Press the button of the new device in two minutes” and click Connect.Step 3: For the configuration of the wireless adapter, please choose “Push the button on my access point or wireless router” in the configuration utility of the WPS as below, and click Connect.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 107 - The WPS Configuration Screen of Wireless Adapter Step 4: Wait for a while until the next screen appears. Click OK to complete the WPS configuration. The WPS Configuration Screen of Wireless Adapter Method Two: Enter the PIN into my AP Step 1: For the configuration of the wireless adapter, please choose “Enter the PIN of this device into my access point or wireless router” in the configuration utility of the WPS as below, and click Connect.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 108 - The WPS Configuration Screen of Wireless Adapter )Note:In this example, the default PIN code of this adapter is 16952898 as the above figure shown.Step 2: Keep the WPS Status as Enabled and click the Add Device button in Figure 5-3. Step 3: Choose “Enter the new device's PIN” and enter the PIN code ˄take 16952898 for example˅ of the wireless adapter in the field after PIN as shown in the figure below. Then click Connect.Figure 5-5 Add A New DeviceMethod Three: Enter the PIN from my AP Step 1: Get the Current PIN code of the AP in Figure 5-3 (each AP has its unique PIN code. Here takes the PIN code 12345670 of this AP for example).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 109 - Step 2: For the configuration of the wireless adapter, please choose “Enter the PIN of my access point or wireless router” in the configuration utility of the WPS as below, and enter the PIN code of the AP into the field after “Access Point PIN”. Then click Connect.The WPS Configuration Screen of Wireless Adapter )Note:The default PIN code of the AP can be found in its label or the WPS configuration screen as Figure 5-3. You will see the following screen when the new device has successfully connected to the network. Figure 5-6 )Note:1) The WPS LED on the AP will light green for five minutes if the device has been successfully added to the network.2) The WPS function cannot be configured if the Wireless function of the AP is disabled. Please make sure the Wireless function is enabled before configuring the WPS.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 110 - 5.5 Working Mode The Router supports five operation mode types: Wireless Router,Access Point, Repeater, Client and Wireless Client Router. Please select one you want. Click Save to save your choice, which is shown as Figure 5-7. Figure 5-7 Wireless Working Mode Settings ¾Wireless Router - The wireless Router Mode. In this mode, the device enables multi-user to share Internet via DSL/Cable Modem. The only wired port works as WAN. ¾Access Point - The wireless access point mode. ¾Repeater - The wireless Repeater Mode. It could extend the range of wireless network. ¾Client - The Client Mode. The computer connected by Ethernet could get access to an AP by Client mode. ¾WISP Client Router - In this mode, the device enables multiple users to share Internet connection from WISP. 5.6 NetworkFigure 5-8 the Network menu There is only one submenu under the Network menu (shown in Figure 5-8): LAN.5.6.1 LANChoose menu “Network ė LAN”, and then you can configure the IP parameters of the LAN on the screen as below.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 111 - Figure 5-9 LAN ¾MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can not be changed. ¾Type - Choosing Smart IP (DHCP) to get IP address from DHCP server, or choosing static IP to config IP address manually. ¾IP Address - Enter the IP address of your system in dotted-decimal notation (factory default - 192.168.0.254). ¾Subnet Mask - An address code that determines the size of the network. Normally 255.255.255.0 is used as the subnet mask. ¾IGMP Proxy - The Internet Group Management Protocol(IGMP) feature allows your devices in LAN can watch TV. )Note:1. If you change the IP Address of LAN, you must use the new IP Address to login to the Router. 2. If the new LAN IP Address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automaticallyˈwhile the Virtual Server and DMZ Host will not take effect until they are re-configured. 3. When you choose the Smart IP(DHCP) mode, the DHCP Server function will be disabled. 5.7 Wireless Figure 5-10 Wireless menu
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 112 - There are five submenus under the Wireless menu (shown in Figure 5-10): Wireless Settings,Wireless Security, Wireless MAC Filtering, Wireless Advanced and Wireless Statistics. Clickany of them, and you will be able to configure the corresponding function. 5.7.1 Wireless Settings Choose menu “Wireless ė Wireless Settings”, and then you can configure the basic settings for the wireless network on this page. Figure 5-11 Wireless Settings - AP ¾Wireless Network Name - Enter a string of up to 32 characters. The same name of SSID (Service Set Identification) must be assigned to all wireless devices in your network. The default SSID is set to be TP-LINK_XXXXXX (XXXXXX indicates the last unique six numbers of each Router’s MAC address). But it is recommended strongly that you change your networks name (SSID) to a different value. This value is case-sensitive. For example, TESTis NOT the same as test.¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. ¾Channel - This field determines which operating frequency will be used. The default channel is set to Auto. It is not necessary to change the wireless channel unless you notice interference problems with another nearby access point. ¾Mode - Select the desired mode. The default setting is 11bgn mixed. x11bg mixed - Select if you are using both 802.11b and 802.11g wireless clients.x11bgn mixed - Select if you are using a mix of 802.11b, 11g, and 11n wireless clients.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 113 - When 11bg mixed mode is selected, only 11bg mixed wireless stations can connect to the Router. It is strongly recommended that you set the Mode to 11bgn mixed, and all of 802.11b/g/n wireless stations can connect to the Router. )Note:If 11bg mixed mode is selected in the Mode field, the Channel Width selecting field will turn grey and the value will become 20M, which is unable to be changed. ¾Channel Width - Select any channel width from the pull-down list. The default setting is automatic, which can automatically adjust the channel width for your clients. ¾Enable Wireless Router Radio - The wireless radio of the Router can be enabled or disabled to allow wireless stations access. If enabled, the wireless stations will be able to access the Router. Otherwise, wireless stations will not be able to access the Router. ¾Enable SSID Broadcast - If you select the Enable SSID Broadcast checkbox, the wireless router will broadcast its name (SSID) on the air. Be sure to click the Save button to save your settings on this page. )Note:1. The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. zNear the center of the area in which your wireless stations will operate. zIn an elevated location such as a high shelf. zAway from the potential sources of interference, such as PCs, microwaves, and cordless phones. zAway from large metal surfaces. 2. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. 5.7.2 Wireless Security Choose menu “Wireless ė Wireless Security”, and then you can configure the security settings of your wireless network. There are three wireless security modes supported by the Router: WPA/WPA2-Personal, WPA/WPA2-Enterprise and WEP (Wired Equivalent Privacy).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 114 - Figure 5-12 Wireless Security ¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. ¾WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.xVersion- you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic, which can selectWPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. xEncryption-When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. )Note:If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 5-13.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 115 - Figure 5-13 ¾WPA /WPA2-Enterprise - It’s based on Radius Server. xVersion- you can choose the version of the WPA security from the pull-down list. The default setting is Automatic, which can selectWPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. xEncryption -You can select Automatic,TKIP or AES.xRadius Server IP - Enter the IP address of the Radius server.xRadius Port - Enter the port that Radius server used. xRadius Password - Enter the password for the Radius server. xGroup Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. ¾WEP - It is based on the IEEE 802.11 standard. xType - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can selectShared Keyor Open Systemauthentication type automatically based on the wireless station's capability and request. xWEP Key Format-Hexadecimal andASCII formats are provided here.Hexadecimalformat stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length.xWEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. xKey Type- You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit -You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 116 - 152-bit - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 16 ASCII characters. )Note:If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. 5.7.3 Wireless MAC Filtering Choose menu “Wireless ė Wireless MAC Filtering”, and then you can control the wireless access by configuring the Wireless MAC Filtering function, as shown in Figure 5-14. Figure 5-14 Wireless MAC Filtering To filter wireless users by MAC Address, click Enabled. The default setting is Disabled.¾MAC Address - The wireless station's MAC address that you want to access. ¾Status - The status of this entry, either Enabled or Disabled.¾Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 5-15: Figure 5-15 Add or Modify Wireless MAC Address Filtering entry
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 117 - To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B. 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3. Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to save this entry. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page. Click the Previous button to return to the previous page. For example: If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the Router, but all the other wireless stations cannot access the Router, you can configure the Wireless MAC Address Filtering list by following these steps: 1. Click the Enable button to enable this function. 2. Select the radio button “Allow the stations specified by any enabled entries in the list to access” for Filtering Rules.3. Delete all or disable all entries if there are any entries already. 4. Click theAdd New...button. xEnter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. xEnter wireless station A/B in the Description field. xSelect Enabled in the Status pull-down list. xClick the Save button. xClick the Back button. The filtering rules that configured should be similar to the following list:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 118 - 5.7.4 Wireless Advanced Choose menu “Wireless ė Wireless Advanced”, and then you can configure the advanced settings of your wireless network. Figure 5-16 Wireless Advanced ¾Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. ¾RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346.¾Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. ¾DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 119 - messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. ¾Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended enabled. ¾Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time.¾Enable AP Isolation - This function isolate all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled.)Note:If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 5.7.5 Wireless Statistics Choose menu “Wireless ė Wireless Statistics”, and then you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 5-17 Wireless Statistics ¾MAC Address - The connected wireless station's MAC address ¾Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected¾Received Packets - Packets received by the station ¾Sent Packets - Packets sent by the station ¾Configure - The button is used for loading the item to the Wireless MAC Filtering list. You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 120 - If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. )Note:This page will be refreshed automatically every 5 seconds. 5.8 DHCP Figure 5-18 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 5-18), DHCP Settings,DHCP Client List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 5.8.1 DHCP Settings Choose menu “DHCP ė DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure 5-19. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router in the LAN. Figure 5-19 DHCP Settings ¾DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 121 - ¾Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. ¾End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. ¾Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ¾Default Gateway (Optional) -It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.0.254. ¾Default Domain (Optional) - Input the domain name of your network. ¾Primary DNS - (Optional) Input the DNS IP address provided by your ISP or consult your ISP.¾Secondary DNS (Optional) -Input the IP address of another DNS server if your ISP provides two DNS servers. )Note:1. To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 2. When you choose the Smart IP (DHCP) mode in Network ė LAN, the DHCP Server function will be disabled. You will see the page as below. Figure 5-20 DHCP Settings 5.8.2 DHCP Client List Choose menu “DHCP ė DHCP Clients List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 5-21.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 122 - Figure 5-21 DHCP Client List ¾Client Name-The name of the DHCP client ¾MAC Address - The MAC address of the DHCP client ¾Assigned IP - The IP address that the Router has allocated to the DHCP client ¾Lease Time- The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 5.8.3 Address Reservation Choose menu “DHCP ė Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 5-22).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 5-22 Address Reservation ¾MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾Reserved IP Address - The IP address reserved for the PC by the Router. ¾Status - The status of this entry either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To Reserve an IP address:1. Click the Add New… button. Then Figure 5-23 will pop-up.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 123 - 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 5-23 Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 5.9 USB Settings Figure 5-24 The USB Settings menu There are three submenus under the USB Settings menu (shown in Figure 5-24), Storage Sharing,Media Server and User Accounts. Click any of them, and you will be able to configure the corresponding functions. 5.9.1 Storage Sharing Choose menu “USB SettingsėStorage Sharing”, you can configure a USB disk drive attached to the router and view volume and share such properties as share name, capacity, used space, and free space on this page as shown below.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 124 - Figure 5-25 Storage Sharing ¾Service Status - Indicates the Network Sharing service's current status. You can click the Start button to start the Storage Sharing service and click the Stop button to stop it. ¾Volume - The volume name of the USB drive the users have access to. Volume 1-8 is mapping to USB port1, and Volume 9-16 is mapping to USB port2. ¾Capacity - The storage capacity of the USB driver. ¾Used - The used space of the USB driver. ¾Free - The available space of the USB driver. ¾Use% - The percentage of the used space. ¾Shared - Indicates the shared or non-shared status of the volume. When the volume is shared, you can click the Disable to stop sharing the volume; when volume is non-shared, you can click the Enable button to share the volume. Click the Start button to start the Network Sharing service. Click the Stop button to stop the Network Sharing service. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. This takes the drive offline. A message (as shown in Figure 5-26) will appear on your web browser when it is safe to detach the USB disk. Figure 5-26 Safe Unplug Message
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 125 - Click the Rescan button to start a new scan. Follow the instructions below to set up your router as a file server: 1. Plug an external USB hard disk drive or USB flash drive into this router. 2. Click the Rescan button to find the USB drive that has been attached to the router. 3. Click the Start button to start the Storage Sharing service. 4. Click the Enable button under Shared to enable the disk to share. 5. Click the Open the disk to visit the sharing disk. )Note:1. The router can automatically locate new USB drive. But to display the information about your USB device, you need to click the Rescan button manually. 2. The new settings will not take effect until you restart the service. 3. To unplug the USB drive, click Eject Disk button first. Simply pulling USB drive out of the USB port can cause damage to the device and loss of data. 4. Mounted volumes of each USB port are subject to the 8-volume limit. So you cannot access more than 8 volumes on the USB storage device. 5. If you change the storage settings during the storage connection is established, then the changes will not take effect until the router or the client is rebooted. 5.9.2 Media Server Choose menu “USB SettingsėMedia Server”, you can create media server that allows you to share stored content with other computers and devices on your home network and on the Internet. Figure 5-27 Media Server Setting ¾Server Name - The name of this Media Server. ¾Server Status - Indicates the Media Server’s current status, started or stopped. You can click the Start button to start the Media Server and click the Stop button to stop it. ¾Name - The display name of this folder. ¾File System - The file system type on the partition can be FAT32 or NTFS. ¾Folder - The real full path of the specified folder.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 126 - ¾Delete - You can delete the share folder by click Delete.To set up your media server, please follow the instructions below: 1. Plug an external USB hard disk drive or USB flash drive into this router, and then the screen will appear as shown in Figure 5-28. Figure 5-28 Media Server Setting 2. Click the Start button to start the media server, and then the screen will appear as shown in Figure 5-29. Figure 5-29 Media Server Setting 3. Click the Add share folder button to specify a folder as the search path of media server. The screen will then appear as shown in Figure 5-30.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 127 - Figure 5-30 Add New Folder ¾Display Name - You can enter a display name for the share folder. ¾Share entire partition - Choose this option and then the folders contained in this partition will all be shared. ¾Folder Location- Displays the location of this folder. ¾Select - Check the radio button to select the folder to share. ¾Folder - Displays folders that are in current path. ¾Upper - Click this button to get into the upper folder. ¾Save - Click this button to save your settings and the page will be redirected to the media server configuration page. ¾Back - Click this button to discard the settings and just go to the media server configuration page. 4. Click the Scan All button to scan all the share folders immediately. You can also select the Auto-scan, at same time, select an auto scan interval time by drop-down list. In this case, the media server will auto scan the share folders. )Note:The max share folders number is 6. If you want share a new folder when the number has been reached to be 6, you can delete a share folder and then add a new one. 5.9.3 User Accounts You can specify the user name and password for Storage Sharing users on this page. Storage Sharing users can use Internet Explorer to access files on the USB drive. There are two default user accounts that can access the Storage Sharing. They are Administrator and Guest (as shown in Figure 5-31). Administrator has read/write access to Storage Sharing and
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 128 - can access FTP Server while Guest has read-only access to Storage Sharing and cannot access FTP Server. Figure 5-31 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive. To add a new user account, please follow the steps below: 1. Click Add New User button, and the screen will appear as shown in Figure 5-32. 2. Self-define a User Name.3. Enter the password in the Password field. 4. Choose the Storage Authority from the drop-down list, Read and Write or Read Only.Figure 5-32 Add or Modify User Account ¾User Name - Type the user name that you want to give access to the USB drive. The user name must be composed of alphanumeric symbols not exceeding 15 characters in length.¾Password - Enter the password in the Password field. The password must be composed of alphanumeric symbols not exceeding 15 characters in length. For security purposes, the password for each user account is not displayed.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 129 - ¾Storage Authority – Choose Read and Write or Read Only from the drop-down list to assign access authority of Storage Sharing to the user.¾Save - You can click the Save button to save your settings.¾Back - You can click the Back button to discard the settings and just go to the media server configuration page. )Note:Please restart the service for the new settings to take effect. If you cannot use the new user name and password to access the shares, press Windows logo + R to open the Run dialog box and type net use \\192.168.0.254 /delete /yes and press Enter. (192.168.0.254 is your router's LAN IP address. If the LAN IP of the modem connected with your router is 192.168.1.x, the default LAN IP of the router will automatically switch from 192.168.0.254 to 192.168.1.254 to avoid IP conflict; in this case, please try net use\\192.168.1.254 /delete / yes.)5.10 System Tools Figure 5-33 The System Tools menu Choose menu “System Tools”, and then you can see the submenus under the main menu:Diagnostic,Firmware Upgrade,Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 5.10.1 DiagnosticChoose menu “System Tools ė Diagnostic”, and then you can transact Ping or Traceroute function to check connectivity of your network in the following screen.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 130 - Figure 5-34 Diagnostic Tools ¾Diagnostic Tool - Check the radio button to select one diagnostic tool. xPing - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. xTraceroute - This diagnostic tool tests the performance of a connection.)Note:You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries. ¾IP Address/Domain Name - Type the destination IP address (e.g. 202.108.22.5) or Domain name (e.g. http://www.tp-link.com). ¾Pings Count - The number of Ping packets for a Ping connection. The default is 4.¾Ping Packet Size - The size of Ping packet. The default is 64.¾Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. The default is 800.¾Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20.Click Start to check the connectivity of the Internet.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 131 - The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 5-35 Diagnostic Results )Note:Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for Ping function. Option “Tracert Hops” are used for Tracert function.5.10.2 Firmware Upgrade Choose menu “System Tools ė Firmware Upgrade”, and then you can update the latest version of firmware for the Router on the following screen. Figure 5-36 Firmware Upgrade¾Firmware Version - This displays the current firmware version. ¾Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the Router’s current hardware version. To upgrade the Router's firmware, follow these instructions below: 1. Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com). 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 132 - )Note:1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware.2. When you upgrade the Router's firmware, you may lose its current configurations, so before upgrading the firmware please write down some of your customized settings to avoid losing important settings. 3. Do not turn off the Router or press the Reset button while the firmware is being upgraded, otherwise, the Router may be damaged. 4. The Router will reboot after the upgrading has been finished. 5.10.3Factory Defaults Choose menu “System Tools ė Factory Defaults”, and you can restore the configurations of the Router to factory defaults on the following screen. Figure 5-37 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. ¾The default User Name: admin ¾The default Password: admin ¾The default IP Address: 192.168.0.254 ¾The default Subnet Mask: 255.255.255.0 )Note:All changed settings will be lost when defaults are restored. 5.10.4 Backup & Restore Choose menu “System Tools ė Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 5-38.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 133 - Figure 5-38 Backup & Restore Configuration¾Click the Backup button to save all configuration settings as a backup file in your local computer. ¾To upgrade the Router's configuration, follow these instructions. xClick the Browse… button to locate the update file for the Router, or enter the exact path to the Setting file in the text box. xClick the Restore button. )Note:The current configuration will be covered by the uploading configuration file. The upgrade process lasts for 20 seconds and the Router will restart automatically. Keep the Router on during the upgrading process to prevent any damage. 5.10.5 RebootChoose menu “System Tools ė Reboot”, and then you can click the Reboot button to reboot the Router via the next screen. Figure 5-39 Reboot the Router Some settings of the Router will take effect only after rebooting, which include:¾Change the LAN IP Address (system will reboot automatically). ¾Change the DHCP Settings. ¾Change the Wireless configurations. ¾Change the Web Management Port. ¾Upgrade the firmware of the Router (system will reboot automatically). ¾Restore the Router's settings to factory defaults (system will reboot automatically). ¾Update the configuration with the file (system will reboot automatically).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 134 - 5.10.6 Password Choose menu “System Tools ė Password”, and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 5-40. Figure 5-40 Password It is strongly recommended that you should change the factory default user name and password of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password. )Note:The new user name and password must not exceed 14 characters in length and not include any spaces. Enter the new Password twice to confirm. Click the Save button when finished. Click the Clear All button to clear all.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 135 - 5.10.7System Log Choose menu “System Tools ė System Log”, and then you can view the logs of the Router. Figure 5-41 System Log ¾Refresh - Refresh the page to show the latest log list. ¾Save Log - Click to save all the logs in a txt file. ¾Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the later log soon. ¾Clear Log - All the logs will be deleted from this device permanently, not just from the page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 136 - Chapter 6. Configuration for Repeater Mode This chapter will show each Web page's key functions and the configuration way for Repeater Mode of TL-WR710N. 6.1LoginAfter your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions. Figure 6-1 The detailed explanations for each Web page’s key function are listed below. 6.2 Status The Status page provides the current status information about the Router on Repeater Mode. All information is read-only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 137 - Figure 6-2 Status ¾Firmware Version - The version information of the Router’s firmware. ¾Hardware Version - The version information of the Router’s hardware. ¾Wired - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. xMAC address - The physical address of the Router, as seen from the LAN. xIP address - The LAN IP address of the Router. xSubnet Mask - The subnet mask associated with LAN IP address. ¾Wireless - This field displays basic information or status for wireless function, you can configure them in the Wireless > Wireless Settings page. xWorking Mode - The current wireless working mode in use. xWireless Name of Root AP - The SSID of Root AP. xChannel - The current wireless channel in use. xMode - The current wireless mode which the Router works on.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 138 - xChannel Width - The current wireless channel width in use. xMAC Address - The physical address of the Router, as seen from the WLAN. ¾Traffic Statistics - The Router’s traffic statistics.xReceived (Bytes) - Traffic that counted in bytes has been received out from the WAN port. xReceived (Packets) - Traffic that counted in packets has been received out from the WAN port.xSent (Bytes) - Traffic that counted in bytes has been sent out from the WAN port. xSent (Packets) - Traffic that counted in packets has been sent out from the WAN port. ¾System Up Time-The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 6.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide."6.4 Working Mode The Router supports five operation mode types: Wireless Router,Access Point, Repeater, Client and Wireless Client Router. Please select one you want. Click Save to save your choice, which is shown as Figure 5-7. Figure 6-3 Working Mode ¾Wireless Router - The wireless Router Mode. In this mode, the device enables multi-user to share Internet via DSL/Cable Modem. The only wired port works as WAN. ¾Access Point - The wireless access point mode. ¾Repeater - The wireless Repeater Mode. It could extend the range of wireless network. ¾Client - The Client Mode. The computer connected by Ethernet could get access to an AP by Client mode.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 139 - ¾WISP Client Router - In this mode, the device enables multiple users to share Internet connection from WISP. 6.5 NetworkFigure 6-4 the Network menu There is only one submenu under the Network menu (shown in Figure 6-4): LAN.6.5.1 LANChoose menu “Network ė LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 6-5 LAN ¾MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed. ¾Type - Choosing Smart IP (DHCP) to get IP address from DHCP server, or choosing static IP to config IP address manually. ¾IP Address - Enter the IP address of your system in dotted-decimal notation (factory default - 192.168.0.254). ¾Subnet Mask - An address code that determines the size of the network. Normally 255.255.255.0 is used as the subnet mask. ¾IGMP Proxy - The Internet Group Management Protocol(IGMP) feature allows your devices in LAN can watch TV. )Note:1. If you change the IP Address of LAN, you must use the new IP Address to login to the Router. 2. If the new LAN IP Address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automaticallyˈwhile the Virtual Server and DMZ Host will not take effect until they are re-configured.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 140 - 6.6 Wireless Figure 6-6 Wireless menu There are five submenus under the Wireless menu (shown in Figure 6-6): Wireless Settings,Wireless Security, MAC Filtering, Wireless Advanced and Wireless Statistics. Click it, and you will be able to configure the corresponding function. 6.6.1 Wireless Settings Choose menu “Wireless ė Wireless Settings”, and then you can configure the basic settings for the wireless network on this page. Figure 6-7 Wireless Settings - Repeater ¾Repeater Mode - In Repeater mode, the wireless repeater relays signal between its stations and the root AP for greater wireless range.xUniversal Repeater - In Repeater mode, the AP with WDS disabled will relay data to an associated root AP. AP function is enabled meanwhile.xWDS Repeater - In WDS Repeater mode, the AP with WDS enabled will relay data to an associated root AP. AP function is enabled meanwhile.¾Wireless Name of Root AP - The SSID of AP that you want to access.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 141 - ¾MAC Address of Root AP - The MAC address of AP that you want to access.¾Survey - Click this button, you can search the AP which runs in the environment.¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance. ¾Wireless Security Mode - This option should be chosen according to the security configuration of the AP you want to access. It is recommended that the security type is the same as your AP’s security type.¾Wireless Password - If the AP your router is going to connect need password, you need to fill the password in this blank. Click Survey button on the Wireless page as shown in Figure 6-7, and then AP List page will appear as shown in Figure 6-8. Find the SSID of the Access Point you want to access, and click Connect in the corresponding row. For example, the third item is selected. The target network’s SSID will be automatically filled into the corresponding box which is shown as the Figure 6-7. ¾Figure 6-8 AP List Be sure to click the Save button to save your settings on this page. )Note:1. The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. zNear the center of the area in which your wireless stations will operate. zIn an elevated location such as a high shelf. zAway from the potential sources of interference, such as PCs, microwaves, and cordless phones. zAway from large metal surfaces.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 142 - 2. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. 6.6.2 Wireless Security Choose menu “Wireless ė Wireless Security”, and then you can configure the security settings of your wireless network. There are three wireless security modes supported by the Router: WPA/WPA2-Personal, WPA/WPA2-Enterprise and WEP (Wired Equivalent Privacy). Figure 6-9 Wireless Security ¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. ¾WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.xVersion- you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic, which can selectWPA-PSK (Pre-shared key of WPA) or
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 143 - WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. xEncryption-When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. )Note:If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 6-10. Figure 6-10 ¾WPA /WPA2-Enterprise - It’s based on Radius Server. xVersion- you can choose the version of the WPA security from the pull-down list. The default setting is Automatic, which can selectWPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. xEncryption -You can select Automatic,TKIP or AES.xRadius Server IP - Enter the IP address of the Radius server.xRadius Port - Enter the port that Radius server used. xRadius Password - Enter the password for the Radius server. xGroup Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. ¾WEP - It is based on the IEEE 802.11 standard. xType - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can selectShared Keyor Open Systemauthentication type automatically based on the wireless station's capability and request. xWEP Key Format-Hexadecimal andASCII formats are provided here.Hexadecimalformat stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 144 - xWEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. xKey Type- You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit -You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters. 152-bit - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 16 ASCII characters. )Note:If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. 6.6.3 Wireless MAC Filtering Choose menu “Wireless ė Wireless MAC Filtering”, and then you can control the wireless access by configuring the Wireless MAC Filtering function, as shown in Figure 6-11. Figure 6-11 Wireless MAC Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disabled.¾MAC Address - The wireless station's MAC address that you want to access. ¾Status - The status of this entry, either Enabled or Disabled.¾Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 6-12:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 145 - Figure 6-12 Add or Modify Wireless MAC Address Filtering entry To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B. 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3. Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to save this entry. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page. Click the Previous button to return to the previous page. For example: If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the Router, but all the other wireless stations cannot access the Router, you can configure the Wireless MAC Address Filtering list by following these steps: 1. Click the Enable button to enable this function. 2. Select the radio button “Allow the stations specified by any enabled entries in the list to access” for Filtering Rules.3. Delete all or disable all entries if there are any entries already.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 146 - 4. Click theAdd New...button. xEnter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. xEnter wireless station A/B in the Description field. xSelect Enabled in the Status pull-down list. xClick the Save button. xClick the Back button. The filtering rules that configured should be similar to the following list: 6.6.4 Wireless Advanced Choose menu “Wireless ė Wireless Advanced”, and then you can configure the advanced settings of your wireless network. Figure 6-13 Wireless Advanced ¾Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. ¾RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 147 - ¾Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. ¾DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. ¾Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended enabled. ¾Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time.¾Enable AP Isolation - This function isolate all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled.)Note:If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 6.6.5 Wireless Statistics Choose menu “Wireless ė Wireless Statistics”, and then you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 6-14 Wireless Statistics ¾MAC Address - The connected wireless station's MAC address ¾Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 148 - ¾Received Packets - Packets received by the station ¾Sent Packets - Packets sent by the station ¾Configure - The button is used for loading the item to the Wireless MAC Filtering list. You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. )Note:This page will be refreshed automatically every 5 seconds. 6.7 DHCP Figure 6-15 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 6-15), DHCP Settings,DHCP Client List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 6.7.1 DHCP Settings Choose menu “DHCP ė DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure 6-16. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router in the LAN.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 149 - Figure 6-16 DHCP Settings ¾DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually. ¾Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. ¾End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. ¾Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ¾Default Gateway (Optional) -It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.0.254. ¾Default Domain (Optional) - Input the domain name of your network. ¾Primary DNS - (Optional) Input the DNS IP address provided by your ISP or consult your ISP.¾Secondary DNS (Optional) -Input the IP address of another DNS server if your ISP provides two DNS servers. )Note:1. To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 2. When you choose the Smart IP (DHCP) mode in Network ė LAN, the DHCP Server function will be disabled. You will see the page as below.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 150 - Figure 6-17 DHCP Settings 6.7.2 DHCP Client List Choose menu “DHCP ė DHCP Client List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 6-18. Figure 6-18 DHCP Client List ¾Client Name-The name of the DHCP client ¾MAC Address - The MAC address of the DHCP client ¾Assigned IP - The IP address that the Router has allocated to the DHCP client ¾Lease Time- The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 6.7.3 Address Reservation Choose menu “DHCP ė Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 6-19).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 151 - Figure 6-19 Address Reservation ¾MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾Reserved IP Address - The IP address reserved for the PC by the Router. ¾Status - The status of this entry either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To Reserve an IP address:1. Click the Add New… button. Then Figure 6-19 will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 6-20 Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 152 - 6.8 USB Settings Figure 6-21 The USB Settings menu There are three submenus under the USB Settings menu (shown in Figure 6-21), Storage Sharing,Media Server and User Accounts. Click any of them, and you will be able to configure the corresponding functions. 6.8.1 Storage Sharing Choose menu “USB SettingsėStorage Sharing”, you can configure a USB disk drive attached to the router and view volume and share such properties as share name, capacity, used space, and free space on this page as shown below. Figure 6-22 Storage Sharing ¾Service Status - Indicates the Network Sharing service's current status. You can click the Start button to start the Storage Sharing service and click the Stop button to stop it. ¾Volume - The volume name of the USB drive the users have access to. Volume 1-8 is mapping to USB port1, and Volume 9-16 is mapping to USB port2. ¾Capacity - The storage capacity of the USB driver. ¾Used - The used space of the USB driver. ¾Free - The available space of the USB driver. ¾Use% - The percentage of the used space.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 153 - ¾Shared - Indicates the shared or non-shared status of the volume. When the volume is shared, you can click the Disable to stop sharing the volume; when volume is non-shared, you can click the Enable button to share the volume. Click the Start button to start the Network Sharing service. Click the Stop button to stop the Network Sharing service. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. This takes the drive offline. A message (as shown in Figure 6-23) will appear on your web browser when it is safe to detach the USB disk. Figure 6-23 Safe Unplug Message Click the Rescan button to start a new scan. Follow the instructions below to set up your router as a file server: 1. Plug an external USB hard disk drive or USB flash drive into this router. 2. Click the Rescan button to find the USB drive that has been attached to the router. 3. Click the Start button to start the Storage Sharing service. 4. Click the Enable button under Shared to enable the disk to share. 5. Click the Open the disk to visit the sharing disk. )Note:1. The router can automatically locate new USB drive. But to display the information about your USB device, you need to click the Rescan button manually. 2. The new settings will not take effect until you restart the service. 3. To unplug the USB drive, click Eject Disk button first. Simply pulling USB drive out of the USB port can cause damage to the device and loss of data. 4. Mounted volumes of each USB port are subject to the 8-volume limit. So you cannot access more than 8 volumes on the USB storage device. 5. If you change the storage settings during the storage connection is established, then the changes will not take effect until the router or the client is rebooted.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 154 - 6.8.2 Media Server Choose menu “USB SettingsėMedia Server”, you can create media server that allows you to share stored content with other computers and devices on your home network and on the Internet. Figure 6-24 Media Server Setting ¾Server Name - The name of this Media Server. ¾Server Status - Indicates the Media Server’s current status, started or stopped. You can click the Start button to start the Media Server and click the Stop button to stop it. ¾Name - The display name of this folder. ¾File System - The file system type on the partition can be FAT32 or NTFS. ¾Folder - The real full path of the specified folder. ¾Delete - You can delete the share folder by click Delete.To set up your media server, please follow the instructions below: 1. Plug an external USB hard disk drive or USB flash drive into this router, and then the screen will appear as shown in Figure 6-25. Figure 6-25 Media Server Setting 2. Click the Start button to start the media server, and then the screen will appear as shown in Figure 6-26.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 155 - Figure 6-26 Media Server Setting 3. Click the Add share folder button to specify a folder as the search path of media server. The screen will then appear as shown in Figure 6-27. Figure 6-27 Add New Folder ¾Display Name - You can enter a display name for the share folder. ¾Share entire partition - Choose this option and then the folders contained in this partition will all be shared. ¾Folder Location- Displays the location of this folder. ¾Select - Check the radio button to select the folder to share. ¾Folder - Displays folders that are in current path. ¾Upper - Click this button to get into the upper folder. ¾Save - Click this button to save your settings and the page will be redirected to the media server configuration page. ¾Back - Click this button to discard the settings and just go to the media server configuration page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 156 - 4. Click the Scan All button to scan all the share folders immediately. You can also select the Auto-scan, at same time, select an auto scan interval time by drop-down list. In this case, the media server will auto scan the share folders. )Note:The max share folders number is 6. If you want share a new folder when the number has been reached to be 6, you can delete a share folder and then add a new one. 6.8.3 User Accounts You can specify the user name and password for Storage Sharing users on this page. Storage Sharing users can use Internet Explorer to access files on the USB drive. There are two default user accounts that can access the Storage Sharing. They are Administrator and Guest (as shown in Figure 6-28). Administrator has read/write access to Storage Sharing and can access FTP Server while Guest has read-only access to Storage Sharing and cannot access FTP Server. Figure 6-28 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive. To add a new user account, please follow the steps below: 1. Click Add New User button, and the screen will appear as shown in Figure 6-29. 2. Self-define a User Name.3. Enter the password in the Password field. 4. Choose the Storage Authority from the drop-down list, Read and Write or Read Only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 157 - Figure 6-29 Add or Modify User Account ¾User Name - Type the user name that you want to give access to the USB drive. The user name must be composed of alphanumeric symbols not exceeding 15 characters in length.¾Password - Enter the password in the Password field. The password must be composed of alphanumeric symbols not exceeding 15 characters in length. For security purposes, the password for each user account is not displayed. ¾Storage Authority – Choose Read and Write or Read Only from the drop-down list to assign access authority of Storage Sharing to the user.¾Save - You can click the Save button to save your settings.¾Back - You can click the Back button to discard the settings and just go to the media server configuration page. )Note:Please restart the service for the new settings to take effect. If you cannot use the new user name and password to access the shares, press Windows logo + Rto open the Run dialog box and type net use \\192.168.0.254 /delete /yes and press Enter. (192.168.0.254 is your router's LAN IP address. If the LAN IP of the modem connected with your router is 192.168.1.x, the default LAN IP of the router will automatically switch from 192.168.0.254 to 192.168.1.254 to avoid IP conflict; in this case, please try net use \\192.168.1.254 /delete / yes.)
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 158 - 6.9System Tools Figure 6-30 The System Tools menu Choose menu “System Tools”, and then you can see the submenus under the main menu:Diagnostic,Firmware Upgrade,Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 6.9.1 DiagnosticChoose menu “System Tools ė Diagnostic”, and then you can transact Ping or Traceroute function to check connectivity of your network in the following screen. Figure 6-31 Diagnostic Tools ¾Diagnostic Tool - Check the radio button to select one diagnostic tool.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 159 - xPing - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. xTraceroute - This diagnostic tool tests the performance of a connection.)Note:You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries. ¾IP Address/Domain Name - Type the destination IP address (e.g. 202.108.22.5) or Domain name (e.g. http://www.tp-link.com). ¾Pings Count - The number of Ping packets for a Ping connection. The default is 4.¾Ping Packet Size - The size of Ping packet. The default is 64.¾Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. The default is 800.¾Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20.Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 6-32 Diagnostic Results )Note:Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for Ping function. Option “Tracert Hops” are used for Tracert function.6.9.2 Firmware Upgrade Choose menu “System Tools ė Firmware Upgrade”, and then you can update the latest version of firmware for the Router on the following screen.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 160 - Figure 6-33 Firmware Upgrade¾Firmware Version - This displays the current firmware version. ¾Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the Router’s current hardware version. To upgrade the Router's firmware, follow these instructions below: 1. Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com). 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. )Note:1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware.2. When you upgrade the Router's firmware, you may lose its current configurations, so before upgrading the firmware please write down some of your customized settings to avoid losing important settings. 3. Do not turn off the Router or press the Reset button while the firmware is being upgraded, otherwise, the Router may be damaged. 4. The Router will reboot after the upgrading has been finished. 6.9.3Factory Defaults Choose menu “System Tools ė Factory Defaults”, and you can restore the configurations of the Router to factory defaults on the following screen.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 161 - Figure 6-34 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. ¾The default User Name: admin ¾The default Password: admin ¾The default IP Address: 192.168.0.254 ¾The default Subnet Mask: 255.255.255.0 )Note:All changed settings will be lost when defaults are restored. 6.9.4 Backup & Restore Choose menu “System Tools ė Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 6-35. Figure 6-35 Backup & Restore Configuration¾Click the Backup button to save all configuration settings as a backup file in your local computer. ¾To upgrade the Router's configuration, follow these instructions. xClick the Browse… button to locate the update file for the Router, or enter the exact path to the Setting file in the text box. xClick the Restore button. )Note:The current configuration will be covered by the uploading configuration file. The upgrade process lasts for 20 seconds and the Router will restart automatically. Keep the Router on during the upgrading process to prevent any damage.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 162 - 6.9.5 RebootChoose menu “System Tools ė Reboot”, and then you can click the Reboot button to reboot the Router via the next screen. Figure 6-36 Reboot the Router Some settings of the Router will take effect only after rebooting, including:¾Change the LAN IP Address (system will reboot automatically). ¾Change the DHCP Settings. ¾Change the Wireless configurations. ¾Change the Web Management Port. ¾Upgrade the firmware of the Router (system will reboot automatically). ¾Restore the Router's settings to factory defaults (system will reboot automatically). ¾Update the configuration with the file (system will reboot automatically. 6.9.6 Password Choose menu “System Tools ė Password”, and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 6-37. Figure 6-37 Password It is strongly recommended that you should change the factory default user name and password of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 163 - )Note:The new user name and password must not exceed 14 characters in length and not include any spaces. Enter the new Password twice to confirm. Click the Save button when finished. Click the Clear All button to clear all. 6.9.7System Log Choose menu “System Tools ė System Log”, and then you can view the logs of the Router. Figure 6-38 System Log ¾Refresh - Refresh the page to show the latest log list. ¾Save Log - Click to save all the logs in a txt file. ¾Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the later log soon. ¾Clear Log - All the logs will be deleted from this device permanently, not just from the page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 164 - Chapter 7. Configuration for Client Mode This chapter will show each Web page's key functions and the configuration way for Client Mode of TL-WR710N. 7.1LoginAfter your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions. Figure 7-1 The detailed explanations for each Web page’s key function are listed below. 7.2 Status The Status page provides the current status information about the Router on Client Mode. All information is read-only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 165 - Figure 7-2 Status ¾Firmware Version - The version information of the Router’s firmware. ¾Hardware Version - The version information of the Router’s hardware. ¾Wired - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page. xMAC address - The physical address of the Router, as seen from the LAN. xIP address - The LAN IP address of the Router. xSubnet Mask - The subnet mask associated with LAN IP address. ¾Wireless - This field displays basic information or status for wireless function, you can configure them in the Wireless > Wireless Settings page. xWorking Mode - The current wireless working mode in use. xWireless Name of Root AP - The SSID of Root AP. xChannel - The current wireless channel in use. xMode - The current wireless mode which the Router works on.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 166 - xChannel Width - The current wireless channel width in use. xMAC Address - The physical address of the Router, as seen from the WLAN. ¾Traffic Statistics - The Router’s traffic statistics.xReceived (Bytes) - Traffic that counted in bytes has been received out from the WAN port. xReceived (Packets) - Traffic that counted in packets has been received out from the WAN port.xSent (Bytes) - Traffic that counted in bytes has been sent out from the WAN port. xSent (Packets) - Traffic that counted in packets has been sent out from the WAN port. ¾System Up Time-The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 7.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide."7.4 Working Mode The Router supports five operation mode types: Wireless Router,Access Point, Repeater, Client and Wireless Client Router. Please select one you want. Click Save to save your choice, which is shown as Figure 7-3. Figure 7-3 Working Mode ¾Wireless Router - The wireless Router Mode. In this mode, the device enables multi-user to share Internet via DSL/Cable Modem. The only wired port works as WAN. ¾Access Point - The wireless access point mode. ¾Repeater - The wireless Repeater Mode. It could extend the range of wireless network. ¾Client - The Client Mode. The computer connected by Ethernet could get access to an AP by Client mode.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 167 - ¾WISP Client Router - In this mode, the device enables multiple users to share Internet connection from WISP. 7.5 NetworkFigure 7-4 the Network menu There is only one submenu under the Network menu (shown in Figure 7-4): LAN.7.5.1 LANChoose menu “Network ė LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 7-5 LAN ¾MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed. ¾Type - Choosing Smart IP (DHCP) to get IP address from DHCP server, or choosing static IP to config IP address manually. ¾IP Address - Enter the IP address of your system in dotted-decimal notation (factory default - 192.168.0.254). ¾Subnet Mask - An address code that determines the size of the network. Normally 255.255.255.0 is used as the subnet mask. ¾IGMP Proxy - The Internet Group Management Protocol(IGMP) feature allows your devices in LAN can watch TV. )Note:1. If you change the IP Address of LAN, you must use the new IP Address to login to the Router. 2. If the new LAN IP Address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automaticallyˈwhile the Virtual Server and DMZ Host will not take effect until they are re-configured.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 168 - 3. When you choose the Smart IP (DHCP) mode, the DHCP Server function will be disabled. 7.6 Wireless Figure 7-6 Wireless menu There are two submenus under the Wireless menu (shown in Figure 7-6): Wireless Settings andWireless Security. Click any of them, and you will be able to configure the corresponding function.7.6.1 Wireless Settings Choose menu “Wireless ė Wireless Settings”, and then you can configure the basic settings for the wireless network on this page. Figure 7-7 Wireless Settings - Client ¾Enable WDS - The AP client can connect to AP with WDS enabled or disabled. If WDS is enabled, all traffic from wired networks will be forwarded in the format of WDS frames consisting of four address fields. If WDS is disabled, three address frames are used. If your AP supports WDS well, please enable this option. ¾Wireless Name of Root AP - Enter the SSID of AP that you want to access. ¾MAC Address of Root AP - Enter the MAC address of AP that you want to access. ¾Region - Select your region from the pull-down list. This field specifies the region where the wireless function of the Router can be used. It may be illegal to use the wireless function of the Router in a region other than one of those specified in this field. If your country or region is not listed, please contact your local government agency for assistance.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 169 - ¾Enable Wireless Radio - The wireless radio of the AP can be enabled or disabled to allow or deny wireless stations to access. If enabled, the wireless stations will be able to access the AP, otherwise, wireless stations will not be able to access the AP. ¾Survey - Click this button, you can search the APs. )Note:1. The operating distance or range of your wireless connection varies significantly based on the physical placement of the Router. For best results, place your Router. zNear the center of the area in which your wireless stations will operate. zIn an elevated location such as a high shelf. zAway from the potential sources of interference, such as PCs, microwaves, and cordless phones. zAway from large metal surfaces. 2. Failure to follow these guidelines can result in significant performance degradation or inability to wirelessly connect to the Router. 7.6.2 Wireless Security Choose menu “Wireless ė Wireless Security”, and then you can configure the security settings of your wireless network. There are three wireless security modes supported by the Router: WPA/WPA2-Personal, WPA/WPA2-Enterprise and WEP (Wired Equivalent Privacy).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 170 - Figure 7-8 Wireless Security ¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. ¾WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.xVersion- you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic, which can selectWPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. xEncryption-When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. )Note:If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 7-9.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 171 - Figure 7-9 ¾WPA /WPA2-Enterprise - It’s based on Radius Server. xVersion- you can choose the version of the WPA security from the pull-down list. The default setting is Automatic, which can selectWPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. xEncryption -You can select Automatic,TKIP or AES.xRadius Server IP - Enter the IP address of the Radius server.xRadius Port - Enter the port that Radius server used. xRadius Password - Enter the password for the Radius server. xGroup Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. ¾WEP - It is based on the IEEE 802.11 standard. xType - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can selectShared Keyor Open Systemauthentication type automatically based on the wireless station's capability and request. xWEP Key Format-Hexadecimal andASCII formats are provided here.Hexadecimalformat stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length.xWEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. xKey Type- You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit -You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 172 - 152-bit - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 16 ASCII characters. )Note:If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. 7.7 DHCP Figure 7-10 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 7-10), DHCP Settings,DHCP Client List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 7.7.1 DHCP Settings Choose menu “DHCP ė DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure 7-11. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router in the LAN. Figure 7-11 DHCP Settings ¾DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 173 - ¾Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. ¾End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. ¾Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ¾Default Gateway (Optional) -It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.0.254. ¾Default Domain (Optional) - Input the domain name of your network. ¾Primary DNS - (Optional) Input the DNS IP address provided by your ISP or consult your ISP.¾Secondary DNS (Optional) -Input the IP address of another DNS server if your ISP provides two DNS servers. )Note:1. To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". This function will take effect until this device reboots. 2. When you choose the Smart IP (DHCP) mode in Network ė LAN, the DHCP Server function will be disabled. You will see the page as below. Figure 7-12 DHCP Settings 7.7.2 DHCP Client List Choose menu “DHCP ė DHCP Client List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 7-13.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 174 - Figure 7-13 DHCP Clients List ¾Client Name-The name of the DHCP client ¾MAC Address - The MAC address of the DHCP client ¾Assigned IP - The IP address that the Router has allocated to the DHCP client ¾Lease Time- The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user. You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 7.7.3 Address Reservation Choose menu “DHCP ė Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 7-14).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 7-14 Address Reservation ¾MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾Reserved IP Address - The IP address reserved for the PC by the Router. ¾Status - The status of this entry either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To Reserve an IP address:1. Click the Add New… button. Then Figure 7-15 will pop-up.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 175 - 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 7-15 Add or Modify an Address Reservation Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 7.8 USB Settings Figure 7-16 The USB Settings menu There are three submenus under the USB Settings menu (shown in Figure 7-16), Storage Sharing,Media Server and User Accounts. Click any of them, and you will be able to configure the corresponding functions. 7.8.1 Storage Sharing Choose menu “USB SettingsėStorage Sharing”, you can configure a USB disk drive attached to the router and view volume and share such properties as share name, capacity, used space, and free space on this page as shown below.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 176 - Figure 7-17 Storage Sharing ¾Service Status - Indicates the Network Sharing service's current status. You can click the Start button to start the Storage Sharing service and click the Stop button to stop it. ¾Volume - The volume name of the USB drive the users have access to. Volume 1-8 is mapping to USB port1, and Volume 9-16 is mapping to USB port2. ¾Capacity - The storage capacity of the USB driver. ¾Used - The used space of the USB driver. ¾Free - The available space of the USB driver. ¾Use% - The percentage of the used space. ¾Shared - Indicates the shared or non-shared status of the volume. When the volume is shared, you can click the Disable to stop sharing the volume; when volume is non-shared, you can click the Enable button to share the volume. Click the Start button to start the Network Sharing service. Click the Stop button to stop the Network Sharing service. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. This takes the drive offline. A message (as shown in Figure 7-18) will appear on your web browser when it is safe to detach the USB disk. Figure 7-18 Safe Unplug Message
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 177 - Click the Rescan button to start a new scan. Follow the instructions below to set up your router as a file server: 1. Plug an external USB hard disk drive or USB flash drive into this router. 2. Click the Rescan button to find the USB drive that has been attached to the router. 3. Click the Start button to start the Storage Sharing service. 4. Click the Enable button under Shared to enable the disk to share. 5. Click the Open the disk to visit the sharing disk. )Note:1. The router can automatically locate new USB drive. But to display the information about your USB device, you need to click the Rescan button manually. 2. The new settings will not take effect until you restart the service. 3. To unplug the USB drive, click Eject Disk button first. Simply pulling USB drive out of the USB port can cause damage to the device and loss of data. 4. Mounted volumes of each USB port are subject to the 8-volume limit. So you cannot access more than 8 volumes on the USB storage device. 5. If you change the storage settings during the storage connection is established, then the changes will not take effect until the router or the client is rebooted. 7.8.2 Media Server Choose menu “USB SettingsėMedia Server”, you can create media server that allows you to share stored content with other computers and devices on your home network and on the Internet. Figure 7-19 Media Server Setting ¾Server Name - The name of this Media Server. ¾Server Status - Indicates the Media Server’s current status, started or stopped. You can click the Start button to start the Media Server and click the Stop button to stop it. ¾Name - The display name of this folder. ¾File System - The file system type on the partition can be FAT32 or NTFS. ¾Folder - The real full path of the specified folder.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 178 - ¾Delete - You can delete the share folder by click Delete.To set up your media server, please follow the instructions below: 1. Plug an external USB hard disk drive or USB flash drive into this router, and then the screen will appear as shown in Figure 7-20. Figure 7-20 Media Server Setting 2. Click the Start button to start the media server, and then the screen will appear as shown in Figure 7-21. Figure 7-21 Media Server Setting 3. Click the Add share folder button to specify a folder as the search path of media server. The screen will then appear as shown in Figure 7-22.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 179 - Figure 7-22 Add New Folder ¾Display Name - You can enter a display name for the share folder. ¾Share entire partition - Choose this option and then the folders contained in this partition will all be shared. ¾Folder Location- Displays the location of this folder. ¾Select - Check the radio button to select the folder to share. ¾Folder - Displays folders that are in current path. ¾Upper - Click this button to get into the upper folder. ¾Save - Click this button to save your settings and the page will be redirected to the media server configuration page. ¾Back - Click this button to discard the settings and just go to the media server configuration page.4. Click the Scan All button to scan all the share folders immediately. You can also select the Auto-scan, at same time, select an auto scan interval time by drop-down list. In this case, the media server will auto scan the share folders. )Note:The max share folders number is 6. If you want share a new folder when the number has been reached to be 6, you can delete a share folder and then add a new one. 7.8.3 User Accounts You can specify the user name and password for Storage Sharing users on this page. Storage Sharing users can use Internet Explorer to access files on the USB drive. There are two default user accounts that can access the Storage Sharing. They are Administrator and Guest (as shown in Figure 7-23). Administrator has read/write access to Storage Sharing and
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 180 - can access FTP Server while Guest has read-only access to Storage Sharing and cannot access FTP Server. Figure 7-23 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive. To add a new user account, please follow the steps below: 1. Click Add New User button, and the screen will appear as shown in Figure 7-23. 2. Self-define a User Name.3. Enter the password in the Password field. 4. Choose the Storage Authority from the drop-down list, Read and Write or Read Only.Figure 7-24 Add or Modify User Account ¾User Name - Type the user name that you want to give access to the USB drive. The user name must be composed of alphanumeric symbols not exceeding 15 characters in length. ¾Password - Enter the password in the Password field. The password must be composed of alphanumeric symbols not exceeding 15 characters in length. For security purposes, the password for each user account is not displayed. ¾Storage Authority – Choose Read and Write or Read Only from the drop-down list to assign access authority of Storage Sharing to the user.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 181 - ¾Save - You can click the Save button to save your settings.¾Back - You can click the Back button to discard the settings and just go to the media server configuration page. )Note:Please restart the service for the new settings to take effect. If you cannot use the new user name and password to access the shares, press Windows logo + Rto open the Run dialog box and type net use \\192.168.0.254 /delete /yes and press Enter. (192.168.0.254 is your router's LAN IP address. If the LAN IP of the modem connected with your router is 192.168.1.x, the default LAN IP of the router will automatically switch from 192.168.0.254 to 192.168.1.254 to avoid IP conflict; in this case, please try net use \\192.168.1.254 /delete / yes.)7.9System Tools Figure 7-25 The System Tools menu Choose menu “System Tools”, and then you can see the submenus under the main menu:Diagnostic,Firmware Upgrade,Factory Defaults, Backup & Restore, Reboot, Password, and System Log. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 7.9.1 DiagnosticChoose menu “System Tools ė Diagnostic”, and then you can transact Ping or Traceroute function to check connectivity of your network in the following screen.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 182 - Figure 7-26 Diagnostic Tools ¾Diagnostic Tool - Check the radio button to select one diagnostic tool. xPing - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. xTraceroute - This diagnostic tool tests the performance of a connection.)Note:You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries. ¾IP Address/Domain Name - Type the destination IP address (e.g. 202.108.22.5) or Domain name (e.g.http://www.tp-link.com). ¾Pings Count - The number of Ping packets for a Ping connection. The default is 4.¾Ping Packet Size - The size of Ping packet. The default is 64.¾Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. The default is 800.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 183 - ¾Traceroute Max TTL - The max number of hops for a Traceroute connection. The default is 20.Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 7-27 Diagnostic Results )Note:Only one user can use this tool at one time. Options “Number of Pings”, “Ping Size” and “Ping Timeout” are used for Ping function. Option “Tracert Hops” are used for Tracert function.7.9.2 Firmware Upgrade Choose menu “System Tools ė Firmware Upgrade”, and then you can update the latest version of firmware for the Router on the following screen. Figure 7-28 Firmware Upgrade¾Firmware Version - This displays the current firmware version. ¾Hardware Version - This displays the current hardware version. The hardware version of the upgrade file must accord with the Router’s current hardware version. To upgrade the Router's firmware, follow these instructions below: 1. Download a more recent firmware upgrade file from the TP-LINK website (http://www.tp-link.com).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 184 - 2. Type the path and file name of the update file into the File field, or click the Browse button to locate the update file. 3. Click the Upgrade button. )Note:1. New firmware versions are posted at http://www.tp-link.com and can be downloaded for free. There is no need to upgrade the firmware unless the new firmware has a new feature you want to use. However, when experiencing problems caused by the Router rather than the configuration, you can try to upgrade the firmware.2. When you upgrade the Router's firmware, you may lose its current configurations, so before upgrading the firmware please write down some of your customized settings to avoid losing important settings. 3. Do not turn off the Router or press the Reset button while the firmware is being upgraded, otherwise, the Router may be damaged. 4. The Router will reboot after the upgrading has been finished. 7.9.3Factory Defaults Choose menu “System Tools ė Factory Defaults”, and you can restore the configurations of the Router to factory defaults on the following screen. Figure 7-29 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. ¾The default User Name: admin ¾The default Password: admin ¾The default IP Address: 192.168.0.254 ¾The default Subnet Mask: 255.255.255.0 )Note:All changed settings will be lost when defaults are restored. 7.9.4 Backup & Restore Choose menu “System Tools ė Backup & Restore”, and then you can save the current configuration of the Router as a backup file and restore the configuration via a backup file as shown in Figure 7-30.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 185 - Figure 7-30 Backup & Restore Configuration¾Click the Backup button to save all configuration settings as a backup file in your local computer. ¾To upgrade the Router's configuration, follow these instructions. xClick the Browse… button to locate the update file for the Router, or enter the exact path to the Setting file in the text box. xClick the Restore button. )Note:The current configuration will be covered by the uploading configuration file. The upgrade process lasts for 20 seconds and the Router will restart automatically. Keep the Router on during the upgrading process to prevent any damage. 7.9.5 RebootChoose menu “System Tools ė Reboot”, and then you can click the Reboot button to reboot the Router via the next screen. Figure 7-31 Reboot the Router Some settings of the Router will take effect only after rebooting, which include:¾Change the LAN IP Address (system will reboot automatically). ¾Change the DHCP Settings. ¾Change the Wireless configurations. ¾Change the Web Management Port. ¾Upgrade the firmware of the Router (system will reboot automatically). ¾Restore the Router's settings to factory defaults (system will reboot automatically). ¾Update the configuration with the file (system will reboot automatically.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 186 - 7.9.6 Password Choose menu “System Tools ė Password”, and then you can change the factory default user name and password of the Router in the next screen as shown in Figure 7-32. Figure 7-32 Password It is strongly recommended that you should change the factory default user name and password of the Router, because all users who try to access the Router's Web-based utility or Quick Setup will be prompted for the Router's default user name and password. )Note:The new user name and password must not exceed 14 characters in length and not include any spaces. Enter the new Password twice to confirm. Click the Save button when finished. Click the Clear All button to clear all.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 187 - 7.9.7System Log Choose menu “System Tools ė System Log”, and then you can view the logs of the Router. Figure 7-33 System Log ¾Refresh - Refresh the page to show the latest log list. ¾Save Log - Click to save all the logs in a txt file. ¾Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the later log soon. ¾Clear Log - All the logs will be deleted from this device permanently, not just from the page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 188 - Chapter 8. Configuration for WISP Client Router Mode This chapter will show each Web page's key functions and the configuration way for WISP Client Router Mode of TL-WR710N. 8.1LoginAfter your successful login, you can configure and manage the device. There are main menus on the left of the web-based utility. Submenus will be available after you click one of the main menus. On the right, there are the corresponding explanations and instructions. Figure 8-1 The detailed explanations for each Web page’s key function are listed below. 8.2 Status The Status page provides the current status information about the Router on WISP Client Router Mode. All information is read-only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 189 - Figure 8-2 Status ¾Firmware Version - The version information of the Router’s firmware. ¾Hardware Version - The version information of the Router’s hardware. ¾LAN - This field displays the current settings or information for the LAN, you can configure them in the Network > LAN page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 190 - xMAC Address - The physical address of the Router, as seen from the LAN. xIP Address - The LAN IP address of the Router. xSubnet Mask - The subnet mask associated with LAN IP address. ¾Wireless - This field displays basic information or status for wireless function, you can configure them in the Wireless > Wireless Settings page. xWorking Mode - The current wireless working mode in use. xWireless Radio - Indicates whether the wireless radio feature of the AP is enabled or disabled.xName (SSID) - The SSID of the AP. xChannel - The current wireless channel in use. xMode - The current wireless mode which the Router works on. xChannel Width - The current wireless channel width in use. xMAC Address - The physical address of the Router, as seen from the WLAN. xClient Status - The status of Client. ¾WAN - This field displays the current settings or information for the WAN, you can configure them in the Network > WAN page.xMAC Address - The physical address of the WAN port, as seen from the Internet. xIP Address - The current WAN (Internet) IP Address. This field will be blank or 0.0.0.0 if the IP Address is assigned dynamically and there is no connection to the Internet. xSubnet Mask - The subnet mask associated with the WAN IP Address. xDefault Gateway - The Gateway currently used by the Router is shown here. When you use Dynamic IP as the connection Internet type, the Renew button will be displayed here. Click the Renew Button to obtain new IP parameters dynamically from the ISP. And if you have got an IP address, Release button will be displayed here. Click the Release button to release the IP address the Router has obtained from the ISP. xDNS Server - The DNS (Domain Name System) server IP addresses currently used by the Router. xOnline Time - The time that you online. When you use PPPoE as WAN connection type, the online time is displayed here. Click the Connect or Disconnect button to connect to or disconnect from Internet. ¾Secondary Connection - Besides PPPoE, if you use an extra connection type to connect to a local area network provided by ISP, then parameters of this secondary connection will be shown in this area.xIP Address - The current WAN (Internet) IP Address. This field will be blank or 0.0.0.0 if the IP Address is assigned dynamically and there is no connection to the Internet.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 191 - xSubnet Mask - The subnet mask associated with the WAN IP Address. Click the Release to delete the network parameters, and click the Renew button to obtaining network parameters. ¾Traffic Statistics - The Router’s traffic statistics.xReceived (Bytes) - Traffic that counted in bytes has been received out from the WAN port. xReceived (Packets) - Traffic that counted in packets has been received out from the WAN port.xSent (Bytes) - Traffic that counted in bytes has been sent out from the WAN port. xSent (Packets) - Traffic that counted in packets has been sent out from the WAN port. ¾System Up Time-The length of the time since the Router was last powered on or reset. Click the Refresh button to get the latest status and settings of the Router. 8.3 Quick Setup Please refer to Section 3.2: "Quick Installation Guide."8.4 Working Mode The Router supports five operation mode types: Wireless Router,Access Point, Repeater, Client and Wireless Client Router. Please select one you want. Click Save to save your choice, which is shown as Figure 8-3. Figure 8-3 Working Mode ¾Wireless Router - The wireless Router Mode. In this mode, the device enables multi-user to share Internet via DSL/Cable Modem. The only wired port works as WAN. ¾Access Point - The wireless access point mode. ¾Repeater - The wireless Repeater Mode. It could extend the range of wireless network. ¾Client - The Client Mode. The computer connected by Ethernet could get access to an AP by Client mode.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 192 - ¾WISP Client Router - In this mode, the device enables multiple users to share Internet connection from WISP. 8.5 NetworkFigure 8-4 The Network menu There are three submenus under the Network menu (shown in Figure 8-4): WAN,MAC Cloneand LAN.Click any of them, and you will be able to configure the corresponding function. 8.5.1 WANChoose menu “Network ė WAN”, and then you can configure the IP parameters of the WAN on the screen below. 1. If your ISP provides the DHCP service, please choose Dynamic IP type, and the Router will automatically get IP parameters from your ISP. You can see the page as follow (Figure 8-5): Figure 8-5 WAN – Dynamic IPThis page displays the WAN IP parameters assigned dynamically by your ISP, including IP address,Subnet Mask,Default Gateway, etc. Click the Renew button to renew the IP parameters from your ISP. Click the Release button to release the IP parameters.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 193 - ¾MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Size unless required by your ISP. ¾Use These DNS Servers - If your ISP gives you one or two DNS addresses, select UseThese DNS Servers and enter the primary and secondary addresses into the correct fields. Otherwise, the DNS servers will be assigned dynamically from your ISP. )Note:If you find error when you go to a website after entering the DNS addresses, it is likely that your DNS servers are set up improperly. You should contact your ISP to get DNS server addresses. ¾Host Name - This option specifies the Host Name of the Router. ¾Get IP with Unicast DHCP - A few ISPs' DHCP servers do not support the broadcast applications. If you cannot get the IP Address normally, you can choose this option. (It is rarely required.) Click the Save button to save your settings. 2. If your ISP provides a static or fixed IP Address,Subnet Mask,Default Gateway and DNSsetting, select Static IP. The Static IP settings page will appear as shown in Figure 8-6. Figure 8-6 WAN - Static IP¾IP Address - Enter the IP address in dotted-decimal notation provided by your ISP. ¾Subnet Mask - Enter the subnet Mask in dotted-decimal notation provided by your ISP, usually is 255.255.255.0. ¾Default Gateway - Enter the gateway IP address in dotted-decimal notation provided by your ISP.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 194 - ¾MTU Size - The normal MTU (Maximum Transmission Unit) value for most Ethernet networks is 1500 Bytes. It is not recommended that you change the default MTU Sizeunless required by your ISP. ¾Primary/Secondary DNS - (Optional) Enter one or two DNS addresses in dotted-decimal notation provided by your ISP. Click the Save button to save your settings. 3. If your ISP provides a PPPoE connection, select PPPoE/Russia PPPoE option. Then you should enter the following parameters (Figure 8-7): Figure 8-7 WAN – PPPoE/Russia PPPoE¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Confirm Password - Enter again the Password provided by your ISP to ensure the password you entered is correct. ¾Secondary Connection - It’s available only for PPPoE Connection. If your ISP provides an extra Connection type such as Dynamic/Static IP to connect to a local area network, then you can check the radio button of Dynamic/Static IP to activate this secondary connection.xDisabled - The Secondary Connection is disabled by default, so there is PPPoE connection only. This is recommended.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 195 - xDynamic IP - You can check this radio button to use Dynamic IP as the secondary connection to connect to the local area network provided by ISP. xStatic IP - You can check this radio button to use Static IP as the secondary connection to connect to the local area network provided by ISP. ¾Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects. ¾Connect Automatically - The connection can be re-established automatically when it was down. ¾Time-based Connecting - The connection will only be established in the period from the start time to the end time (both are in HH:MM format). )Note:Only when you have configured the system time on “System Tools ĺ Time” page, will the Time-based Connecting function can take effect. ¾Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automaticallyafter a specified inactivity period and re-established when you attempt to access the Internet again. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Caution: Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. If you want to do some advanced configurations, please click the Advanced button, and the page shown in Figure 8-8 will then appear:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 196 - Figure 8-8 PPPoE Advanced Settings ¾MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ¾Service Name/AC Name - The service name and AC (Access Concentrator) name should not be configured unless you are sure it is necessary for your ISP. In most cases, leaving these fields blank will work. ¾ISP Specified IP Address - If your ISP does not automatically assign IP addresses to the Router during login, please click “Use IP address specified by ISP” check box and enter the IP address provided by your ISP in dotted-decimal notation.¾Detect Online Interval - The Router will detect Access Concentrator online at every interval. The default value is “0”. You can input the value between “0” and “120”. The value “0” means no detect. ¾Primary DNS/Secondary DNS - If your ISP does not automatically assign DNS addresses to the Router during login, please click “Use the following DNS servers”check box and enter the IP address in dotted-decimal notation of your ISP’s primary DNS server. If a secondary DNS server address is available, enter it as well. Click the Save button to save your settings. 4. If your ISP provides BigPond Cable connection, please select BigPond Cable option. Then you should enter the following parameters (Figure 8-9):
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 197 - Figure 8-9 WAN – BigPond Cable ¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Auth Server - Enter the authenticating server IP address or host name. ¾Auth Domain - Type in the domain suffix server name based on your location, ¾MTU Size - The default MTU size is “1480” bytes, which is usually fine. It is not recommended that you change the default MTU Size unless required by your ISP. ¾Connect on Demand - In this mode, the Internet connection can be terminated automatically after a specified inactivity period (Max Idle Time) and be re-established when you attempt to access the Internet again. If you want your Internet connection keeps active all the time, please enter “0” in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet access disconnects. ¾Connect Automatically - The connection can be re-established automatically when it was down. ¾Connect Manually - You can click the Connect/Disconnect button to connect/disconnect immediately. This mode also supports the Max Idle Time function as Connect on Demand mode. The Internet connection can be disconnected automatically
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 198 - after a specified inactivity period and re-established when you attempt to access the Internet again. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. Caution: Sometimes the connection cannot be terminated although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. Click the Save button to save your settings. 5. If your ISP provides L2TP connection, please select L2TP/Russia L2TP option. Then you should enter the following parameters (Figure 8-10): Figure 8-10 WAN – L2TP/Russia L2TP¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Dynamic IP/ Static IP - Choose either as you are given by your ISP. Click the Connectbutton to connect immediately. Click the Disconnect button to disconnect immediately.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 199 - ¾Connect on Demand - You can configure the Router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, check the radio button. If you want your Internet connection to remain active at all times, enter 0 in the Max Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. ¾Connect Automatically - Connect automatically after the Router is disconnected. To use this option, check the radio button. ¾Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, check the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number of minutes that you wish to have the Internet connecting last unless a new link is requested. Caution: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, because some applications are visiting the Internet continually in the background. Click the Save button to save your settings. 6. If your ISP provides PPTP connection, please select PPTP/Russia PPTP option. And you should enter the following parameters (Figure 8-11):
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 200 - Figure 8-11 WAN – PPTP/Russia PPTP ¾User Name/Password - Enter the User Name and Password provided by your ISP. These fields are case-sensitive. ¾Dynamic IP/ Static IP - Choose either as you are given by your ISP and enter the ISP’s IP address or the domain name. If you choose static IP and enter the domain name, you should also enter the DNS assigned by your ISP. And click the Save button. Click the Connect button to connect immediately. Click the Disconnect button to disconnect immediately. ¾Connect on Demand - You can configure the Router to disconnect from your Internet connection after a specified period of inactivity (Max Idle Time). If your Internet connection has been terminated due to inactivity, Connect on Demand enables the Router to automatically re-establish your connection as soon as you attempt to access the Internet again. If you wish to activate Connect on Demand, check the radio button. If you want your Internet connection to remain active at all times, enter “0” in the Max
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 201 - Idle Time field. Otherwise, enter the number of minutes you want to have elapsed before your Internet connection terminates. ¾Connect Automatically - Connect automatically after the Router is disconnected. To use this option, check the radio button. ¾Connect Manually - You can configure the Router to make it connect or disconnect manually. After a specified period of inactivity (Max Idle Time), the Router will disconnect from your Internet connection, and you will not be able to re-establish your connection automatically as soon as you attempt to access the Internet again. To use this option, click the radio button. If you want your Internet connection to remain active at all times, enter "0" in the Max Idle Time field. Otherwise, enter the number in minutes that you wish to have the Internet connecting last unless a new link is requested. Caution: Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time because some applications are visiting the Internet continually in the background. Click the Save button to save your settings. 8.5.2 MAC Clone Choose menu “Network ė MAC Clone”, and then you can configure the WAN MAC address on the screen below, as shown in Figure 8-12: Figure 8-12 MAC Address CloneSome ISPs require that you register the MAC Address of your adapter. Changes are rarely needed here. ¾WAN MAC Address - This field displays the current MAC address of the WAN port. If your ISP requires you to register the MAC address, please enter the correct MAC address into this field in XX-XX-XX-XX-XX-XX format (X is any hexadecimal digit). ¾Your PC's MAC Address - This field displays the MAC address of the PC that is managing the Router. If the MAC address is required, you can click the Clone MAC Address Tobutton and this MAC address will fill in the WAN MAC Address field. Click Restore Factory MAC to restore the MAC address of WAN port to the factory default value.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 202 - Click the Save button to save your settings. )Note:1. Only the PC on your LAN can use the MAC Address Clone function. 2. If you change WAN MAC Address when the WAN connection is PPPoE, it will not take effect until the connection is re-established. 8.5.3 LANChoose menu “Network ė LAN”, and then you can configure the IP parameters of the LAN on the screen as below. Figure 8-13 LAN ¾MAC Address - The physical address of the LAN ports, as seen from the LAN. The value can't be changed. ¾IP Address - Enter the IP address of your Router in dotted-decimal notation (factory default: 192.168.0.254). ¾Subnet Mask - An address code that determines the size of the network. Normally use 255.255.255.0 as the subnet mask. ¾IGMP Proxy - The Internet Group Management Protocol (IGMP) feature allows your devices in LAN can watch TV. )Note:1. If you change the IP Address of LAN, you must use the new IP Address to login to the Router. 2. If the new LAN IP Address you set is not in the same subnet with the previous one, the IP Address pool in the DHCP server will be configured automaticallyˈwhile the Virtual Server and DMZ Host will not take effect until they are re-configured.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 203 - 8.6 Wireless Figure 8-14 Wireless menu There are five submenus under the Wireless menu (shown in Figure 8-14): Wireless Settings,Wireless Security, Wireless MAC Filtering, Wireless Advanced and Wireless Statistics. Clickany of them, and you will be able to configure the corresponding function. 8.6.1 Wireless Settings Choose menu “Wireless ė Wireless Settings”, and then you can configure the basic settings for the wireless network on this page. Figure 8-15 Wireless Security ¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 204 - ¾WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.xVersion- you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic, which can selectWPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. xEncryption-When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. )Note:If you check the WPA-PSK/WPA2-PSK radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 4-22. Figure 8-16¾WPA /WPA2-Enterprise - It’s based on Radius Server. xVersion- you can choose the version of the WPA security from the pull-down list. The default setting is Automatic, which can selectWPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. xEncryption -You can select Automatic,TKIP or AES.xRadius Server IP - Enter the IP address of the Radius server.xRadius Port - Enter the port that Radius server used. xRadius Password - Enter the password for the Radius server. xGroup Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. ¾WEP - It is based on the IEEE 802.11 standard. xType - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can selectShared Keyor Open Systemauthentication type automatically based on the wireless station's capability and request.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 205 - xWEP Key Format-Hexadecimal andASCII formats are provided here.Hexadecimalformat stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length.xWEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. xKey Type- You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit -You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters. 152-bit - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 16 ASCII characters. )Note:If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 206 - 8.6.2 Wireless Security Figure 8-17 Wireless Security ¾Disable Security - The wireless security function can be enabled or disabled. If disabled, the wireless stations will be able to connect the Router without encryption. But it’s strongly recommended to choose one of the following modes to enable security. ¾WPA-PSK/WPA2-Personal - It’s the WPA/WPA2 authentication type based on pre-shared passphrase.xVersion- you can choose the version of the WPA-PSK security on the drop-down list. The default setting is Automatic, which can selectWPA-PSK (Pre-shared key of WPA) or WPA2-PSK (Pre-shared key of WPA) automatically based on the wireless station's capability and request. xEncryption-When WPA-PSK or WPA is set as the Authentication Type, you can select either Automatic, or TKIP or AES as Encryption. )Note:If you check the WPA/WPA2-Personal radio button and choose TKIP encryption, you will find a notice in red as shown in Figure 8-18.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 207 - Figure 8-18 ¾WPA /WPA2-Enterprise - It’s based on Radius Server. xVersion- you can choose the version of the WPA security from the pull-down list. The default setting is Automatic, which can selectWPA (Wi-Fi Protected Access) or WPA2 (WPA version 2) automatically based on the wireless station's capability and request. xEncryption -You can select Automatic,TKIP or AES.xRadius Server IP - Enter the IP address of the Radius server.xRadius Port - Enter the port that Radius server used. xRadius Password - Enter the password for the Radius server. xGroup Key Update Period - Specify the group key update interval in seconds. The value should be 30 or above. Enter 0 to disable the update. ¾WEP - It is based on the IEEE 802.11 standard. xType - you can choose the type for the WEP security on the pull-down list. The default setting is Automatic, which can selectShared Keyor Open Systemauthentication type automatically based on the wireless station's capability and request. xWEP Key Format-Hexadecimal andASCII formats are provided here.Hexadecimalformat stands for any combination of hexadecimal digits (0-9, a-f, A-F) in the specified length. ASCII format stands for any combination of keyboard characters in the specified length.xWEP Key (Password) - Select which of the four keys will be used and enter the matching WEP key that you create. Make sure these values are identical on all wireless stations in your network. xKey Type- You can select the WEP key length (64-bit, or 128-bit, or 152-bit.) for encryption. "Disabled" means this WEP key entry is invalid. 64-bit -You can enter 10 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 5 ASCII characters. 128-bit - You can enter 26 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 13 ASCII characters.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 208 - 152-bit - You can enter 32 hexadecimal digits (any combination of 0-9, a-f, A-F, zero key is not promoted) or 16 ASCII characters. )Note:If you do not set the key, the wireless security function is still disabled even if you have selected Shared Key as Authentication Type. Be sure to click the Save button to save your settings on this page. 8.6.3 Wireless MAC Filtering Choose menu “Wireless ė Wireless MAC Filtering”, and then you can control the wireless access by configuring the Wireless MAC Filtering function, as shown in Figure 8-19. Figure 8-19 Wireless MAC Filtering To filter wireless users by MAC Address, click Enable. The default setting is Disabled.¾MAC Address - The wireless station's MAC address that you want to access. ¾Status - The status of this entry, either Enabled or Disabled.¾Description - A simple description of the wireless station. To Add a Wireless MAC Address filtering entry, click the Add New… button. The "Add or Modify Wireless MAC Address Filtering entry" page will appear, shown in Figure 8-20: Figure 8-20 Add or Modify Wireless MAC Address Filtering entry
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 209 - To add or modify a MAC Address Filtering entry, follow these instructions: 1. Enter the appropriate MAC Address into the MAC Address field. The format of the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). For example: 00-0A-EB-B0-00-0B. 2. Give a simple description for the wireless station in the Description field. For example: Wireless station A. 3. Select Enabled or Disabled for this entry on the Status pull-down list. 4. Click the Save button to save this entry. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page. Click the Previous button to return to the previous page. For example: If you desire that the wireless station A with MAC address 00-0A-EB-B0-00-0B and the wireless station B with MAC address 00-0A-EB-00-07-5F are able to access the Router, but all the other wireless stations cannot access the Router, you can configure the Wireless MAC Address Filtering list by following these steps: 1. Click the Enable button to enable this function. 2. Select the radio button “Allow the stations specified by any enabled entries in the list to access” for Filtering Rules.3. Delete all or disable all entries if there are any entries already. 4. Click theAdd New...button. 1) Enter the MAC address 00-0A-EB-B0-00-0B/00-0A-EB-00-07-5F in the MAC Address field. 2) Enter wireless station A/B in the Description field. 3) Select Enabled in the Status pull-down list. 4) Click the Save button. 5) Click the Back button. The filtering rules that configured should be similar to the following list:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 210 - Figure 8-21 Filtering Rules 8.6.4 Wireless Advanced Choose menu “Wireless ė Wireless Advanced”, and then you can configure the advanced settings of your wireless network. Figure 8-22 Wireless Advanced ¾Transmit Power - Here you can specify the transmit power of Router. You can select High, Middle or Low which you would like. High is the default setting and is recommended. ¾Beacon Interval - Enter a value between 20-1000 milliseconds for Beacon Interval here. The beacons are the packets sent by the Router to synchronize a wireless network. Beacon Interval value determines the time interval of the beacons. The default value is 100. ¾RTS Threshold - Here you can specify the RTS (Request to Send) Threshold. If the packet is larger than the specified RTS Threshold size, the Router will send RTS frames to a particular receiving station and negotiate the sending of a data frame. The default value is 2346.¾Fragmentation Threshold - This value is the maximum size determining whether packets will be fragmented. Setting the Fragmentation Threshold too low may result in poor network performance because of excessive packets. 2346 is the default setting and is recommended. ¾DTIM Interval - This value determines the interval of the Delivery Traffic Indication Message (DTIM). A DTIM field is a countdown field informing clients of the next window for listening to
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 211 - broadcast and multicast messages. When the Router has buffered broadcast or multicast messages for associated clients, it sends the next DTIM with a DTIM Interval value. You can specify the value between 1-255 Beacon Intervals. The default value is 1, which indicates the DTIM Interval is the same as Beacon Interval. ¾Enable WMM - WMM function can guarantee the packets with high-priority messages being transmitted preferentially. It is strongly recommended enabled. ¾Enable Short GI - This function is recommended for it will increase the data capacity by reducing the guard interval time.¾Enable AP Isolation - This function isolate all connected wireless stations so that wireless stations cannot access each other through WLAN. This function will be disabled if WDS/Bridge is enabled.)Note:If you are not familiar with the setting items in this page, it's strongly recommended to keep the provided default values; otherwise it may result in lower wireless network performance. 8.6.5 Wireless Statistics Choose menu “Wireless ė Wireless Statistics”, and then you can see the MAC Address, Current Status, Received Packets and Sent Packets for each connected wireless station. Figure 8-23 Wireless Statistics ¾MAC Address - The connected wireless station's MAC address ¾Current Status - The connected wireless station's running status, one of STA-AUTH / STA-ASSOC / STA-JOINED / WPA / WPA-PSK / WPA2 / WPA2-PSK / AP-UP / AP-DOWN / Disconnected¾Received Packets - Packets received by the station ¾Sent Packets - Packets sent by the station. ¾Configure - The button is used for loading the item to the Wireless MAC Filtering list. xAllow - If the Wireless MAC Filtering function enable, allow the station to access.xDeny - If the Wireless MAC Filtering function enable, deny the station to access.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 212 - You cannot change any of the values on this page. To update this page and to show the current connected wireless stations, click on the Refresh button. If the numbers of connected wireless stations go beyond one page, click the Next button to go to the next page and click the Previous button to return the previous page. )Note:This page will be refreshed automatically every 5 seconds. 8.7 DHCP Figure 8-24 The DHCP menu There are three submenus under the DHCP menu (shown in Figure 8-24): DHCP Settings,DHCP Client List and Address Reservation. Click any of them, and you will be able to configure the corresponding function. 8.7.1 DHCP Settings Choose menu “DHCP ė DHCP Settings”, and then you can configure the DHCP Server on the page as shown in Figure 8-25. The Router is set up by default as a DHCP (Dynamic Host Configuration Protocol) server, which provides the TCP/IP configuration for all the PC(s) that are connected to the Router in the LAN. Figure 8-25 DHCP Settings ¾DHCP Server - Enable or Disable the DHCP server. If you disable the Server, you must have another DHCP server within your network or else you must configure the computer manually.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 213 - ¾Start IP Address - Specify an IP address for the DHCP Server to start with when assigning IP addresses. 192.168.0.100 is the default start address. ¾End IP Address - Specify an IP address for the DHCP Server to end with when assigning IP addresses. 192.168.0.199 is the default end address. ¾Address Lease Time - The Address Lease Time is the amount of time a network user will be allowed connection to the Router with their current dynamic IP Address. Enter the amount of time in minutes and the user will be "leased" this dynamic IP Address. After the time is up, the user will be automatically assigned a new dynamic IP address. The range of the time is 1 ~ 2880 minutes. The default value is 120 minutes. ¾Default Gateway (Optional) -It is suggested to input the IP address of the LAN port of the Router. The default value is 192.168.0.254. ¾Default Domain (Optional) - Input the domain name of your network. ¾Primary DNS - (Optional) Input the DNS IP address provided by your ISP or consult your ISP. Or consult your ISP. ¾Secondary DNS (Optional) -Input the IP address of another DNS server if your ISP provides two DNS servers. )Note:To use the DHCP server function of the Router, you must configure all computers on the LAN as "Obtain an IP Address automatically". 8.7.2 DHCP Client List Choose menu “DHCP ė DHCP Client List”, and then you can view the information about the clients attached to the Router in the screen as shown in Figure 8-26. Figure 8-26 DHCP Client List ¾Client Name-The name of the DHCP client ¾MAC Address - The MAC address of the DHCP client ¾Assigned IP - The IP address that the Router has allocated to the DHCP client ¾Lease Time- The time of the DHCP client leased. After the dynamic IP address has expired, a new dynamic IP address will be automatically assigned to the user.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 214 - You cannot change any of the values on this page. To update this page and to show the current attached devices, click the Refresh button. 8.7.3 Address Reservation Choose menu “DHCP ė Address Reservation”, and then you can view and add a reserved address for clients via the next screen (shown in Figure 8-27).When you specify a reserved IP address for a PC on the LAN, that PC will always receive the same IP address each time when it accesses the DHCP server. Reserved IP addresses should be assigned to the servers that require permanent IP settings. Figure 8-27 Address Reservation ¾MAC Address - The MAC address of the PC for which you want to reserve an IP address. ¾Reserved IP Address - The IP address reserved for the PC by the Router. ¾Status - The status of this entry, either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To Reserve an IP address:1. Click the Add New… button. Then will pop-up. 2. Enter the MAC address (in XX-XX-XX-XX-XX-XX format.) and IP address (in dotted-decimal notation) of the computer for which you want to reserve an IP address. 3. Click the Save button. Figure 8-28 Add or Modify an Address Reservation Entry
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 215 - To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and Click the Previous button to return the previous page. 8.8 USB Settings Figure 8-29 The USB Settings menu There are three submenus under the USB Settings menu (shown in Figure 8-29), Storage Sharing,Media Server and User Accounts. Click any of them, and you will be able to configure the corresponding functions. 8.8.1 Storage Sharing Choose menu “USB SettingsėStorage Sharing”, you can configure a USB disk drive attached to the router and view volume and share such properties as share name, capacity, used space, and free space on this page as shown below. Figure 8-30 Storage Sharing ¾Service Status - Indicates the Network Sharing service's current status. You can click the Start button to start the Storage Sharing service and click the Stop button to stop it.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 216 - ¾Volume - The volume name of the USB drive the users have access to. Volume 1-8 is mapping to USB port1, and Volume 9-16 is mapping to USB port2. ¾Capacity - The storage capacity of the USB driver. ¾Used - The used space of the USB driver. ¾Free - The available space of the USB driver. ¾Use% - The percentage of the used space. ¾Shared - Indicates the shared or non-shared status of the volume. When the volume is shared, you can click the Disable to stop sharing the volume; when volume is non-shared, you can click the Enable button to share the volume. Click the Start button to start the Network Sharing service. Click the Stop button to stop the Network Sharing service. Click the Eject Disk button to safely remove the USB storage device that is connected to USB port. This takes the drive offline. A message (as shown in Figure 8-31) will appear on your web browser when it is safe to detach the USB disk. Figure 8-31 Safe Unplug Message Click the Rescan button to start a new scan. Follow the instructions below to set up your router as a file server: 1. Plug an external USB hard disk drive or USB flash drive into this router. 2. Click the Rescan button to find the USB drive that has been attached to the router. 3. Click the Start button to start the Storage Sharing service. 4. Click the Enable button under Shared to enable the disk to share. 5. Click the Open the disk to visit the sharing disk. )Note:1. The router can automatically locate new USB drive. But to display the information about your USB device, you need to click the Rescan button manually. 2. The new settings will not take effect until you restart the service.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 217 - 3. To unplug the USB drive, click Eject Disk button first. Simply pulling USB drive out of the USB port can cause damage to the device and loss of data. 4. Mounted volumes of each USB port are subject to the 8-volume limit. So you cannot access more than 8 volumes on the USB storage device. 5. If you change the storage settings during the storage connection is established, then the changes will not take effect until the router or the client is rebooted. 8.8.2 Media Server Choose menu “USB SettingsėMedia Server”, you can create media server that allows you to share stored content with other computers and devices on your home network and on the Internet. Figure 8-32 Media Server Setting ¾Server Name - The name of this Media Server. ¾Server Status - Indicates the Media Server’s current status, started or stopped. You can click the Start button to start the Media Server and click the Stop button to stop it. ¾Name - The display name of this folder. ¾File System - The file system type on the partition can be FAT32 or NTFS. ¾Folder - The real full path of the specified folder. ¾Delete - You can delete the share folder by click Delete.To set up your media server, please follow the instructions below: 1. Plug an external USB hard disk drive or USB flash drive into this router, and then the screen will appear as shown in Figure 8-33. Figure 8-33 Media Server Setting
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 218 - 2. Click the Start button to start the media server, and then the screen will appear as shown in Figure 8-34. Figure 8-34 Media Server Setting 3. Click the Add share folder button to specify a folder as the search path of media server. The screen will then appear as shown in Figure 8-35. Figure 8-35 Add New Folder ¾Display Name - You can enter a display name for the share folder. ¾Share entire partition - Choose this option and then the folders contained in this partition will all be shared. ¾Folder Location- Displays the location of this folder. ¾Select - Check the radio button to select the folder to share. ¾Folder - Displays folders that are in current path. ¾Upper - Click this button to get into the upper folder. ¾Save - Click this button to save your settings and the page will be redirected to the media server configuration page.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 219 - ¾Back - Click this button to discard the settings and just go to the media server configuration page. 4. Click the Scan All button to scan all the share folders immediately. You can also select the Auto-scan, at same time, select an auto scan interval time by drop-down list. In this case, the media server will auto scan the share folders. )Note:The max share folders number is 6. If you want share a new folder when the number has been reached to be 6, you can delete a share folder and then add a new one. 8.8.3 User Accounts You can specify the user name and password for Storage Sharing users on this page. Storage Sharing users can use Internet Explorer to access files on the USB drive. There are two default user accounts that can access the Storage Sharing. They are Administrator and Guest (as shown in Figure 8-36). Administrator has read/write access to Storage Sharing and can access FTP Server while Guest has read-only access to Storage Sharing and cannot access FTP Server. Figure 8-36 User Account Management Only Administrator can use a Web browser to transfer the files from a PC to the Writable shared volume on the USB drive. To add a new user account, please follow the steps below: 1. Click Add New User button, and the screen will appear as shown in Figure 8-36. 2. Self-define a User Name.3. Enter the password in the Password field. 4. Choose the Storage Authority from the drop-down list, Read and Write or Read Only.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 220 - Figure 8-37 Add or Modify User Account ¾User Name - Type the user name that you want to give access to the USB drive. The user name must be composed of alphanumeric symbols not exceeding 15 characters in length. ¾Password - Enter the password in the Password field. The password must be composed of alphanumeric symbols not exceeding 15 characters in length. For security purposes, the password for each user account is not displayed. ¾Storage Authority – Choose Read and Write or Read Only from the drop-down list to assign access authority of Storage Sharing to the user.¾Save - You can click the Save button to save your settings.¾Back - You can click the Back button to discard the settings and just go to the media server configuration page. )Note:Please restart the service for the new settings to take effect. If you cannot use the new user name and password to access the shares, press Windows logo + Rto open the Run dialog box and type net use \\192.168.0.254 /delete /yes and press Enter. (192.168.0.254 is your router's LAN IP address. If the LAN IP of the modem connected with your router is 192.168.1.x, the default LAN IP of the router will automatically switch from 192.168.0.254 to 192.168.1.254 to avoid IP conflict; in this case, please try net use \\192.168.1.254 /delete / yes.)8.9 Forwarding Figure 8-38 The Forwarding menu
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 221 - There are four submenus under the Forwarding menu (shown in Figure 8-38): Virtual Servers,Port Triggering,DMZ and UPnP. Click any of them, and you will be able to configure the corresponding function. 8.9.1 Virtual Servers Choose menu “Forwarding ė Virtual Servers”, and then you can view and add virtual servers in the screen as shown in Figure 8-39. Virtual servers can be used for setting up public services on your LAN, such as DNS, Email and FTP. A virtual server is defined as a service port, and all requests from the Internet to this service port will be redirected to the computer specified by the server IP. Any PC that was used for a virtual server must have a static or reserved IP Address because its IP Address may be changed when using the DHCP function. Figure 8-39 Virtual Servers ¾Service Port - The numbers of External Ports. You can type a service port or a range of service ports (in XXX – YYY format, XXX is the start port number, YYY is the end port number). ¾Internal Port - The Internal Service Port number of the PC running the service application. You can leave it blank if the Internal Port is the same as the Service Port, or enter a specific port number when Service Port is a single one. ¾IP Address - The IP Address of the PC providing the service application. ¾Protocol - The protocol used for this application, either TCP,UDP, or All (all protocols supported by the Router). ¾Status - The status of this entry, either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To setup a virtual server entry: 1. Click the Add New… button, the next screen will pop-up as shown in Figure 8-39. 2. Select the service port you want to use from the Common Service Port list. If the Common Service Port list does not have the service that you want to use, type the service port number or service port range in the Service Port box. 3. Type the IP Address of the computer in the IP Address box.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 222 - 4. Select the protocol used for this application, either TCP,UDP, or All.5. Select the Enable to enable the virtual server. 6. Click the Save button. Figure 8-40 Add or Modify a Virtual Server Entry )Note:If your computer or server has more than one type of available service, please select another service, and enter the same IP Address for that computer or server. To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable/Disable All button to make all entries enabled/disabled. Click the Delete All button to delete all entries. Click the Next button to go to the next page and click the Previous button to return the previous page.)Note:If you set the service port of the virtual server as 80, you must set the Web management port on “Security ė Remote Management” page to be any other value except 80 such as 8080. Otherwise there will be a conflict to disable the virtual server. 8.9.2 Port Triggering Choose menu “Forwarding ė Port Triggering”, and then you can view and add port triggering in the screen as shown in Figure 8-41. Some applications require multiple connections, like Internet games, video conferencing, Internet calling and so on. These applications cannot work
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 223 - with a pure NAT Router. Port Triggering is used for some of these applications that can work with an NAT Router. Figure 8-41 Port Triggering Once the Router is configured, the operation is as follows: 1. A local host makes an outgoing connection using a destination port number defined in the Trigger Port field. 2. The Router records this connection, opens the incoming port or ports associated with this entry in the Port Triggering table, and associates them with the local host. 3. When necessaryˈ the external host will be able to connect to the local host using one of the ports defined in the Incoming Ports field.¾Trigger Port - The port for outgoing traffic. An outgoing connection using this port will trigger this rule. ¾Trigger Protocol - The protocol used for Trigger Ports, either TCP,UDP, or All (all protocols supported by the Router). ¾Incoming Ports - The port or port range used by the remote system when it responds to the outgoing request. A response using one of these ports will be forwarded to the PC that triggered this rule. You can input at most 5 groups of ports (or port sections). Every group of ports must be set apart with ",". For example, 2000-2038, 2050-2051, 2085, 3010-3030. ¾Incoming Protocol - The protocol used for Incoming Ports Range, either TCP or UDP, or ALL (all protocols supported by the Router). ¾Status - The status of this entry, either Enabled or Disabled.¾Modify - To modify or delete an existing entry. To add a new rule, follow the steps below: 1. Click the Add New… button, the next screen will pop-up as shown in Figure 8-41. 2. Select a common application from the Common Applications drop-down list, then the Trigger Port field and the Incoming Ports field will be automatically filled. If the CommonApplications do not have the application you need, enter the Trigger Port and the Incoming Ports manually. 3. Select the protocol used for Trigger Port from the Trigger Protocol drop-down list, either TCP,UDP, or All.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 224 - 4. Select the protocol used for Incoming Ports from the Incoming Protocol drop-down list, either TCP or UDP, or All.5. Select Enable in Status field. 6. Click the Save button to save the new rule. Figure 8-42 Add or Modify a Port Triggering Entry To modify or delete an existing entry: 1. Click the Modify in the entry you want to modify. If you want to delete the entry, click theDelete.2. Modify the information. 3. Click the Save button. Click the Enable All button to make all entries enabled. Click the Disable All button to make all entries disabled. Click the Delete All button to delete all entries. )Note:1. When the trigger connection is released, the corresponding opening ports will be closed. 2. Each rule is allowed to be used only by one host on LAN synchronously. The trigger connection of other hosts on LAN will be refused. 3. Incoming Port Range cannot overlap each other. 8.9.3 DMZChoose menu “Forwarding ė DMZ”, and then you can view and configure DMZ host in the screen as shown in Figure 8-43. The DMZ host feature allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. DMZ host forwards all the ports at the same time. Any PC whose port is being forwarded must have its DHCP client function disabled and should have a new static IP Address assigned to it because its IP Address may be changed when using the DHCP function.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 225 - Figure 8-43 DMZ To assign a computer or server to be a DMZ server: 1. Check the Enable radio button. 2. Enter the IP Address of a local host in the DMZ Host IP Address field. 3. Click the Save button. )Note:After you set the DMZ host, the firewall related to the host will not work.8.9.4 UPnPChoose menu “Forwarding ė UPnP”, and then you can view the information about UPnP (Universal Plug and Play) in the screen as shown in Figure 8-44. The UPnP feature allows the devices, such as Internet computers, to access the local host resources or devices as needed. UPnP devices can be automatically discovered by the UPnP service application on the LAN. Figure 8-44 UPnP ¾Current UPnP Status - UPnP can be enabled or disabled by clicking the Enable or Disablebutton.¾Current UPnP Settings List - This table displays the current UPnP information.xApp Description - The description provided by the application in the UPnP request. xExternal Port - The external port the Router opens for the application. xProtocol - The type of protocol the Router opens for the application. xInternal Port - The Internal port the Router opens for local host. xIP Address - The IP address of the UPnP device that is currently accessing the Router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 226 - xStatus - The status of the port is displayed here. “Enabled” means that the port is still active. Otherwise, the port is inactive. Click Refresh to update the Current UPnP Settings List. 8.10SecurityFigure 8-45 The Security menu There are four submenus under the Security menu as shown in Figure 8-45: Basic Security,Advanced Security, Local Management and Remote Management. Click any of them, and you will be able to configure the corresponding function. 8.10.1 Basic Security Choose menu “Security ė Basic Security”, you can configure the basic security in the screen as shown in Figure 8-46. Figure 8-46 Basic Security ¾Firewall - A firewall protects your network from the outside world. Here you can enable or disable the Router’s firewall. zSPI Firewall - SPI (Stateful Packet Inspection, also known as dynamic packet filtering) helps to prevent cyber attacks by tracking more state per session. It validates that the
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 227 - traffic passing through the session conforms to the protocol. SPI Firewall is enabled by factory default. If you want all the computers on the LAN exposed to the outside world, you can disable it. ¾VPN - VPN Passthrough must be enabled if you want to allow VPN tunnels using IPSec, PPTP, or L2TP protocols to pass through the Router’s firewall.zPPTP Passthrough - Point-to-Point Tunneling Protocol (PPTP) allows the Point-to-Point Protocol (PPP) to be tunneled through an IP network. To allow PPTP tunnels to pass through the Router, keep the default, Enabled.zL2TP Passthrough - Layer 2 Tunneling Protocol (L2TP) is the method used to enable Point-to-Point sessions via the Internet on the Layer 2 level. To allow L2TP tunnels to pass through the Router, keep the default, Enabled.zIPSec Passthrough - Internet Protocol Security (IPSec) is a suite of protocols for ensuring private, secure communications over Internet Protocol (IP) networks, through the use of cryptographic security services. To allow IPSec tunnels to pass through the Router, keep the default, Enabled.¾ALG - It is recommended to enable Application Layer Gateway (ALG) because ALG allows customized Network Address Translation (NAT) traversal filters to be plugged into the gateway to support address and port translation for certain application layer "control/data" protocols such as FTP, TFTP, H323 etc. zFTP ALG - To allow FTP clients and servers to transfer data across NAT, keep the default Enable.zTFTP ALG - To allow TFTP clients and servers to transfer data across NAT, keep the default Enable.zH323 ALG - To allow Microsoft NetMeeting clients to communicate across NAT, keep the default Enable.Click the Save button to save your settings. 8.10.2 Advanced Security Choose menu “Security ė Advanced Security”, you can protect the Router from being attacked by TCP-SYN Flood, UDP Flood and ICMP-Flood in the screen as shown in Figure 8-47.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 228 - Figure 8-47 Advanced Security ¾Packets Statistics Interval (5~60) - The default value is 10. Select a value between 5 and 60 seconds from the drop-down list. The Packets Statistics Interval value indicates the time section of the packets statistics. The result of the statistics is used for analysis by SYN Flood, UDP Flood and ICMP-Flood. ¾DoS Protection - Denial of Service protection. Check the Enable or Disable button to enable or disable the DoS protection function. Only when it is enabled, will the flood filters be enabled. )Note:Dos Protection will take effect only when the Traffic Statistics in “System Tool ė Traffic Statistics” is enabled. ¾Enable ICMP-FLOOD Attack Filtering- Enable or Disable the ICMP-FLOOD Attack Filtering.¾ICMP-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current ICMP-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately. ¾Enable UDP-FLOOD Filtering- Enable or Disable the UDP-FLOOD Filtering. ¾UDP-FLOOD Packets Threshold (5~3600) - The default value is 500. Enter a value between 5 ~ 3600. When the current UPD-FLOOD Packets number is beyond the set value, the Router will startup the blocking function immediately.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 229 - ¾Enable TCP-SYN-FLOOD Attack Filtering- Enable or Disable the TCP-SYN-FLOOD Attack Filtering. ¾TCP-SYN-FLOOD Packets Threshold (5~3600) - The default value is 50. Enter a value between 5 ~ 3600. When the current TCP-SYN-FLOOD Packets numbers is beyond the set value, the Router will startup the blocking function immediately. ¾Ignore Ping Packet From WAN Port - Enable or Disable Ignore Ping Packet From WAN Port. The default setting is disabled. If enabled, the ping packet from the Internet cannot access the Router. ¾Forbid Ping Packet From LAN Port - Enable or Disable Forbid Ping Packet From LAN Port. The default setting is disabled. If enabled, the ping packet from LAN cannot access the Router. This function can be used to defend against some viruses. Click the Save button to save the settings. Click the Blocked DoS Host List button to display the DoS host table by blocking.8.10.3 Local Management Choose menu “Security ė Local Management”, you can configure the management rule in the screen as shown in Figure 8-48. The management feature allows you to deny computers in LAN from accessing the Router. Figure 8-48 Local Management By default, the radio button “All the PCs on the LAN are allowed to access the Router's Web-Based Utility” is checked. If you want to allow PCs with specific MAC Addresses to access the Setup page of the Router's Web-Based Utility locally from inside the network, check the radio button “Only the PCs listed can browse the built-in web pages to perform Administrator tasks”, and then enter each MAC Address in a separate field. The format for the MAC Address is XX-XX-XX-XX-XX-XX (X is any hexadecimal digit). Only the PCs with MAC address listed can
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 230 - use the password to browse the built-in web pages to perform Administrator tasks while all the others will be blocked. After click the Add button, your PC's MAC Address will be placed in the list above. Click the Save button to save your settings. )Note:If your PC is blocked but you want to access the Router again, press and hold the WPS button for more than 5 seconds to reset the Router to factory defaults. 8.10.4Remote Management You can configure the Remote Management function on this page. This feature allows you to manage your Router from a remote location, via the Internet. Figure 8-49 Remote Management ¾Web Management Port - Web browser access normally uses the standard HTTP service port 80. This router’s default remote management Web port number is 80. For greater security, you can change the remote management Web interface to a custom port by entering that number in this box provided. Choose a number between 1024 and 65535, but do not use the number of any common service port. ¾Remote Management IP Address - This is the current address you will use when accessing your router from the Internet. The default IP Address is 0.0.0.0. It means this function is disabled. To enable this function, change the default IP Address to another IP Address as desired. To access the router, you will type your router's WAN IP Address into your browser's Address (in IE) or Location (in Navigator) box, followed by a colon and the custom port number. For example, if your Router's WAN address is 202.96.12.8 and you use port number 8080, enter in your browser: http://202.96.12.8:8080. You will be asked for the router's password. After successfully entering the password, you will be able to access the router's Web-based utility. )Note:Be sure to change the router's default password to a very secure password.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 231 - 8.11 Parental Control Choose menu “Parental Control”, and you can configure the parental control in the screen as shown in Figure 8-50. The Parental Control function can be used to control the internet activities of the child, limit the child to access certain websites and restrict the time of surfing. Figure 8-50 Parental Control Settings ¾Parental Control - Check Enable if you want this function to take effect, otherwise check Disable.¾MAC Address of Parental PC - In this field, enter the MAC address of the controlling PC, or you can make use of the Copy To Above button below. ¾MAC Address of Your PC - This field displays the MAC address of the PC that is managing this Router. If the MAC Address of your adapter is registered, you can click the Copy To Above button to fill this address to the MAC Address of Parental PC field above. ¾Website Description - Description of the allowed website for the PC controlled. ¾Schedule - The time period allowed for the PC controlled to access the Internet. For detailed information, please go to “Access Restrictionė Schedule”.¾Modify - Here you can edit or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New… button and the next screen will pop-up as shown in Figure 8-50. 2. Enter the MAC address of the PC (e.g. 00-11-22-33-44-AA) you’d like to control in the MAC Address of Child PC field. Or you can choose the MAC address from the All Address in Current LAN drop-down list. 3. Give a description (e.g. Allow Google) for the website allowed to be accessed in the Website Description field.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 232 - 4. Enter the allowed domain name of the website, either the full name or the keywords (e.g. google) in the Allowed Domain Name field. Any domain name with keywords in it (e.g.www.google.com) will be allowed. 5. Select from the Effective Time drop-down list the schedule (e.g. Schedule_1) you want the entry to take effect. If there are not suitable schedules for you, click the Schedule in red below to go to the Advance Schedule Settings page and create the schedule you need. 6. In the Status field, you can select Enabled or Disabled to enable or disable your entry. 7. Click the Save button. Click the Enable All button to enable all the rules in the list. Click the Disable All button to disable all the rules in the list. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 8-51 Add or Modify Parental Control Entry For example: If you desire that the child PC with MAC address 00-11-22-33-44-AA can access www.google.com on Saturday only while the parent PC with MAC address 00-11-22-33-44-BB is without any restriction, you should follow the settings below. 1. Click “Parental Control” menu on the left to enter the Parental Control Settings page. Check Enable and enter the MAC address 00-11-22-33-44-BB in the MAC Address of Parental PC field.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 233 - 2. Click “Access Restriction ĺ Schedule” on the left to enter the Schedule Settings page. Click Add New... button to create a new schedule with Schedule Description is Schedule_1, Day is Sat and Time is all day-24 hours. 3. Click “Parental Control” menu on the left to go back to the Add or Modify Parental Control Entry page: zClick Add New... button. zEnter 00-11-22-33-44-AA in the MAC Address of Child PC field. zEnter “Allow Google” in the Website Description field. zEnter “www.google.com” in the Allowed Domain Name field. zSelect “Schedule_1” you create just now from the Effective Time drop-down list. zIn Status field, select Enable. 4. Click Save to complete the settings. Then you will go back to the Parental Control Settings page and see the following list, as shown in Figure 8-52. Figure 8-52 8.12Access Control Figure 8-53 The Access Control menu There are four submenus under the Access Restriction menu as shown in Figure 8-53: Rule,Host,Target and Schedule. Click any of them, and you will be able to configure the corresponding function. 8.12.1 RuleChoose menu “Access Controlė Rule”, you can view and set Access Restriction rules in the screen as shown in Figure 8-54.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 234 - Figure 8-54 Access Control Rule Management ¾Enable Internet Access Restriction - Select the check box to enable the Internet Access Restriction function, so the Default Filter Policy can take effect. ¾Rule Name - Here displays the name of the rule and this name is unique. ¾Host - Here displays the host selected in the corresponding rule. ¾Target - Here displays the target selected in the corresponding rule. ¾Schedule - Here displays the schedule selected in the corresponding rule. ¾Action - Here displays the action the Router takes to deal with the packets. It could be Allowor Deny.Allow means that the Router permits the packets to go through the Router. Denymeans that the Router rejects the packets to go through the Router. ¾Status - This field displays the status of the rule. Enabled means the rule will take effect, Disabled means the rule will not take effect. ¾Modify - Here you can edit or delete an existing rule. To add a new rule, please follow the steps below. 1. Click the Add New… button and the next screen will pop-up as shown in Figure 8-54. 2. Give a name (e.g. Rule_1) for the rule in the Rule Name field.3. Select a host from the Host drop-down list or choose “Click Here To Add New Host List”.4. Select a target from the Target drop-sown list or choose “Click Here To Add New Target List”.5. Select a schedule from the Schedule drop-down list or choose “Click Here To Add New Schedule”.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 235 - 6. In the Action field, select Deny or Allow.7. In the Status field, select Enabled or Disabled to enable or disable your entry. 8. Click the Save button. Click the Enable All button to enable all the rules in the list. Click the Disable All button to disable all the rules in the list. Click the Delete All button to delete all the entries in the table. You can change the entry’s order as desired. Fore entries are before hind entries. Enter the ID number in the first box you want to move and another ID number in second box you want to move to, and then click the Move button to change the entry’s order. Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 8-55 Add or Modify Internet Access Restriction Entry For example: If you desire to allow the host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday and Sunday, and forbid other hosts in the LAN to access the Internet, you should follow the settings below: 1. Click “Access Restriction ė Host” in the left to enter the Host Settings page. Add a new entry with the Host Description is Host_1 and MAC Address is 00-11-22-33-44-AA. 2. Click “Access Restriction ė Target” in the left to enter the Target Settings page. Add a new entry with the Target Description is Target_1 and Domain Name is www.google.com. 3. Click “Access Restriction ė Schedule” in the left to enter the Schedule Settings page. Add a new entry with the Schedule Description is Schedule_1, Day is Sat and Sun, Start Time is 1800 and Stop Time is 2000. 4. Click “Access Restriction ė Rule” in the left to return to the Access Restriction Rule Management page. Select “Enable Internet Access Restriction” and choose "Deny the packets not specified by any access Restriction policy to pass through the Router". 5. Click Add New... button to add a new rule as follows:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 236 - zIn Rule Name field, create a name for the rule. Note that this name should be unique, for example Rule_1. zIn Host field, select Host_1. zIn Target field, select Target_1. zIn Schedule field, select Schedule_1. zIn Action field, select Allow. zIn Status field, select Enabled. zClick Save to complete the settings. Then you will go back to the Access Restriction Rule Management page and see the following list. Figure 8-56 Rule Settings 8.12.2 HostChoose menu “Access Control ė Host”, you can view and set a Host list in the screen as shown in Figure 8-57. The host list is necessary for the Access Restriction Rule. Figure 8-57 Host Settings ¾Host Description - Here displays the description of the host and this description is unique. ¾Information - Here displays the information about the host. It can be IP or MAC. ¾Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below. 1. Click the Add New… button. 2. In the Mode field, select IP Address or MAC Address. zIf you select IP Address, the screen shown is Figure 8-58. 1) In Host Description field, create a unique description for the host (e.g. Host_1).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 237 - 2) In LAN IP Address field, enter the IP address. zIf you select MAC Address, the screen shown is Figure 8-59. 1) In Host Description field, create a unique description for the host (e.g. Host_1). 2) In MAC Address field, enter the MAC address. 3. Click the Save button to complete the settings. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 8-58 Add or Modify a Host Entry Figure 8-59 Add or Modify a Host Entry For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA, you should first follow the settings below: 1. Click Add New... button in Figure 8-57 to enter the Add or Modify a Host Entry page. 2. In Mode field, select MAC Address from the drop-down list. 3. In Host Description field, create a unique description for the host (e.g. Host_1). 4. In MAC Address field, enter 00-11-22-33-44-AA. 5. Click Save to complete the settings. Then you will go back to the Host Settings page and see the following list.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 238 - Figure 8-60 Host Settings 8.12.3 Target Choose menu “Access Control ė Target”, you can view and set a Target list in the screen as shown in Figure 4-65. The target list is necessary for the Access Restriction Rule. Figure 8-61 Target Settings ¾Target Description - Here displays the description about the target and this description is unique.¾Information - The target can be IP address, port, or domain name. ¾Modify - To modify or delete an existing entry. To add a new entry, please follow the steps below.1. Click the Add New… button. 2. In Mode field, select IP Address or Domain Name. zIf you select IP Address, the screen shown is Figure 8-62. 1) In Target Description field, create a unique description for the target (e.g. Target_1). 2) In IP Address field, enter the IP address of the target. 3) Select a common service from Common Service Port drop-down list, so that the Target Port will be automatically filled. If the Common Service Port drop-down list doesn’t have the service you want, specify the Target Port manually. 4) In Protocol field, select TCP, UDP, ICMP or ALL.zIf you select Domain Name, the screen shown is Figure 8-63. 1) In Target Description field, create a unique description for the target (e.g. Target_1).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 239 - 2) In Domain Name field, enter the domain name, either the full name or the keywords (for example Google) in the blank. Any domain name with keywords in it (e.g.www.google.com) will be blocked or allowed. You can enter 4 domain names. 3. Click the Save button. Click the Delete All button to delete all the entries in the table. Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 8-62 Add or Modify an Access Target Entry Figure 8-63 Add or Modify an Access Target Entry For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA in the LAN to access www.google.com only, you should first follow the settings below: 1. Click Add New… button in Figure 8-61 to enter the Add or Modify an Access Target Entry page.2. In Mode field, select Domain Name from the drop-down list. 3. In Target Description field, create a unique description for the target (e.g. Target_1). 4. In Domain Name field, enter www.google.com. 5. Click Save to complete the settings.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 240 - Then you will go back to the Target Settings page and see the following list, Figure 8-64 Target Settings 8.12.4ScheduleChoose menu “Access Control ė Schedule”, you can view and set a Schedule list in the next screen as shown in Figure 8-65. The Schedule list is necessary for the Access Restriction Rule. Figure 8-65 Schedule Settings ¾Schedule Description - Here displays the description of the schedule and this description is unique.¾Day - Here displays the day(s) in a week. ¾Time - Here displays the time period in a day. ¾Modify - Here you can edit or delete an existing schedule. To add a new schedule, follow the steps below. 1. Click Add New... button shown in Figure 8-65 and the next screen will pop-up as shown in Figure 8-66. 2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Day field, select the day or days you need. 4. In Time field, you can select all day-24 hours or you may enter the Start Time and Stop Time in the corresponding field. 5. Click Save to complete the settings. Click the Delete All button to delete all the entries in the table.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 241 - Click the Next button to go to the next page, or click the Previous button return to the previous page.Figure 8-66 Advanced Schedule Settings For example: If you desire to restrict the internet activities of host with MAC address 00-11-22-33-44-AA to access www.google.com only from 18:00 to 20:00 on Saturday andSunday, you should first follow the settings below: 1. Click Add New... button shown in Figure 8-65 to enter the Advanced Schedule Settings page.2. In Schedule Description field, create a unique description for the schedule (e.g. Schedule_1). 3. In Day field, check the Select Days radio button and then select Sat and Sun. 4. In Time field, enter 1800 in Start Time field and 2000 in Stop Time field. 5. Click Save to complete the settings. Then you will go back to the Schedule Settings page and see the following list. Figure 8-67 Schedule Settings
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 242 - 8.13 Advanced Routing Figure 8-68 The Advanced Routing Menu There are two submenus under the Network menu (shown in Figure 4-72): Static Routing Listand SystemRouting Table. Click any of them, and you will be able to configure the corresponding function. 8.13.1 Static Routing List Choose menu “Static Routing”, and you can configure the static route in the next screen, shown in Figure 8-69. A static route is a pre-determined path that network information must travel to reach a specific host or network. Figure 8-69 Static Routing To add static routing entries, follow the steps below. 1. Click Add New… shown in Figure 8-69, you will see the following screen Figure 8-70. Figure 8-70 Add or Modify a Static Route Entry 2. Enter the following data. ¾Destination Network - The Destination IP Address is the address of the network or host that you want to assign to a static route.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 243 - ¾Subnet Mask - The Subnet Mask determines which portion of an IP Address is the network portion, and which portion is the host portion. ¾Default Gateway- This is the IP Address of the gateway device that allows for contact between the Router and the network or host. 3. Select Enabled or Disabled for this entry on the Status drop-down list. 4. Click the Save button to make the entry take effect. Click the Delete button to delete the entry. Click the Enable All button to enable all the entries. Click the Disable All button to disable all the entries. Click the Delete All button to delete all the entries. Click the Previous button to view the information in the previous screen, click the Nextbutton to view the information in the next screen. 8.13.2 System Routing Table Choose menu “Advanced Routing ė System Routing Table”, and you can views all of the valid route entries in use. The Destination IP address, Subnet Mask, Gateway, and Interface will be displayed for each entry. Figure 8-71 Routing Table ¾Destination Network - The Destination IP Address is the address of the network or host to which the static route is assigned. ¾Subnet Mask - The Subnet Mask determines which portion of an IP address is the network portion, and which portion is the host portion. ¾Gateway - This is the IP address of the gateway device that allows for contact between the Router and the network or host. ¾Interface - This interface tells you whether the Destination IP Address is on the LAN & WLAN (internal wired and wireless networks), the WAN (Internet).Click the Refresh button to refresh the data displayed.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 244 - 8.14Bandwidth Control Figure 8-72 The Bandwidth Control menu There are two submenus under the Bandwidth Control menu as shown in Figure 8-72. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 8.14.1 Control Settings Choose menu “Bandwidth Control ė Control Settings”, you can configure the Egress Bandwidth and Ingress Bandwidth in the next screen. Their values you configure should be less than 100000Kbps. For optimal control of the bandwidth, please select the right Line Type and ask your ISP for the total bandwidth of the egress and ingress.Figure 8-73 Bandwidth Control Settings ¾Enable Bandwidth Control - Check this box so that the Bandwidth Control settings can take effect.¾Line Type - Select the right type for you network connection. If you don’t know how to choose, please ask your ISP for the information.¾Egress Bandwidth - The upload speed through the WAN port.¾Ingress Bandwidth - The download speed through the WAN port.8.14.2 Rule List Choose menu “Bandwidth Control ė Rule List”, you can view and configure the Bandwidth Control rules in the screen below.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 245 - Figure 8-74 Bandwidth Control Rule List ¾Description - This is the information about the rules such as address range.¾Egress Bandwidth - This field displays the max and mix upload bandwidth through the WAN port, the default is 0. ¾Ingress Bandwidth - This field displays the max and mix download bandwidth through the WAN port, the default is 0. ¾Enable - This displays the status of the rule. ¾Modify - Click Modify to edit the rule. Click Delete to delete the rule. To add/modify a Bandwidth Control rule, follow the steps below. Step 1: Click Add New… shown in Figure 8-74, you will see a new screen shown in Figure 8-75. Step 2: Enter the information like the screen shown below. Figure 8-75 Bandwidth Control Rule Settings ¾Enable - Enable or disable the rule. ¾IP Range - Interior PC address range. If both are blank (or 0.0.0.0), the domain is no effective. ¾Port Range - The port range which the Interior PC access the outside PC. If all are blank (or 0), the domain is no effective. ¾Protocol - Transport layer protocol, here there are All, TCP, UDP.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 246 - ¾Egress Bandwidth - The max and the min upload speed which through the WAN port, default number is 0. ¾Ingress Bandwidth - The max and the min download speed through the WAN port, default number is 0. Step 3: Click the Save button. 8.15 IP & MAC Binding Figure 8-76 The IP & MAC Binding menu There are two submenus under the IP & MAC Binding menu: Binding Setting and ARP List.Click any of them, and you will be able to scan or configure the corresponding function. The detailed explanations for each submenu are provided below. 8.15.1 Binding Setting This page displays the IP & MAC Binding Setting table; you can operate it in accord with your desire.Figure 8-77 IP & MAC Binding Setting ¾MAC Address - The MAC address of the controlled computer in the LAN. ¾IP Address - The assigned IP address of the controlled computer in the LAN. ¾Bind - Whether or not enable the ARP binding. ¾Modify - Edit or delete item.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 247 - When you want to add or modify an IP & MAC Binding entry, you can click the Add New button or Modify button, and then you will go to the next page. This page is used for adding or modifying an IP & MAC Binding entry. Figure 8-78 IP & MAC Binding Setting (Add & Modify) To add IP & MAC Binding entries: 1. Click the Add New.. button. 2. Enter the MAC Address and IP Address. 3. Select the Bind checkbox. 4. Click the Save button to save it. To modify or delete an existing entry:1. Find the desired entry in the table. 2. Click Modify or Delete as desired on the Modify column. To find an existing entry:1. Click the Find button (shown in Figure 8-77). 2. Enter the MAC Address or IP Address. 3. Enter the Find button in the next page (shown in Figure 8-79). Figure 8-79 Find IP & MAC Binding Entry
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 248 - Click the Enable All button to make all entries enabled. Click the Delete All button to delete all entries. 8.15.2 ARP List To manage the computer, you could observe the computers in the LAN by checking the relationship of MAC address and IP address on the ARP list, and you could configure the items on the ARP list also. This page displays the ARP List; it shows all the existing IP & MAC Binding entries.Figure 8-80 ARP List ¾MAC Address - The MAC address of the controlled computer in the LAN. ¾IP Address - The assigned IP address of the controlled computer in the LAN. ¾Status - Enabled or Disabled of the MAC address and IP address binding. ¾Configure - Load or delete item. ¾Load - Load the item to the IP & MAC Binding list. ¾Delete - Delete the item. 1. Click the Bind All button to bind all the current items, available after enable. 2. Click the Load All button to load all items to the IP & MAC Binding list. 3. Click the Refresh button to refresh all items. )Note:An item could not be loaded to the IP & MAC Binding list if the IP address of the item has been loaded before. Error warning will prompt as well. Likewise, "Load All" only loads the items without interference to the IP & MAC Binding list. 8.16 Dynamic DNS The Router offers the DDNS (Dynamic Domain Name System) feature, which allows the hosting of a website, FTP server, or e-mail server with a fixed domain name (named by yourself) and a dynamic IP address, and then your friends can connect to your server by entering your domain
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 249 - name no matter what your IP address is. Before using this feature, you need to sign up for DDNS service providers such as www.no-ip.com,www.comexe.cn, or www.dyndns.org. The Dynamic DNS client service provider will give you a password or key. 8.16.1 No-IP DDNS If the dynamic DNS Service Provider you select is www.no-ip.com, the page will appear as shown in Figure 8-81. Figure 8-81 No-IP DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider. 4. Click the Login button to log in the DDNS service. Connection Status - The status of the DDNS service connection is displayed here. Click Logout to log out the DDNS service. )Note:If you want to login again with another account after a successful login, please click the Logoutbutton, then input your new username and password and click the Login button. 8.16.2 Comexe.cn DDNS If the dynamic DNS Service Provider you select is www.comexe.cn, the page will appear as shown in Figure 8-82.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 250 - Figure 8-82 Comexe.cn DDNS Settings To set up for DDNS, follow these instructions: 1. Type the Domain Name received from your dynamic DNS service provider. 2. Type the User Name for your DDNS account. 3. Type the Password for your DDNS account. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to log out of the DDNS service. 8.16.3Dyndns org DDNS If the dynamic DNS Service Provider you select is www.dyndns.org, the page will appear as shown in Figure 8-83.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 251 - Figure 8-83 Dyndns.org DDNS Settings To set up for DDNS, follow these instructions: 1. Type the User Name for your DDNS account. 2. Type the Password for your DDNS account. 3. Type the Domain Name you received from dynamic DNS service provider here. 4. Click the Login button to log in to the DDNS service. Connection Status -The status of the DDNS service connection is displayed here. Click Logout to logout of the DDNS service. 8.17 System Tools Figure 8-84 The System Tools menu There are nine submenus under the System Tools menu: Time Settings,Diagnostic,Firmware Upgrade,Factory Defaults, Backup and Restore, Reboot, Password, System Log and
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 252 - Statistics. Click any of them, and you will be able to configure the corresponding function. The detailed explanations for each submenu are provided below. 8.17.1Time Settings You can set time manually or get GMT from the Internet for the router on this page: Figure 8-85 Time Settings ¾Time Zone - Select your local time zone from this pull-down list. ¾Date - Enter your local date in MM/DD/YY into the right blanks. ¾Time - Enter your local time in HH/MM/SS into the right blanks. To set time manually, follow the steps below: 1. Select your local time zone. 2. Enter the Date in Month/Day/Year format. 3. Enter the Time in Hour/Minute/Second format. 4. Click Save.For automatic time synchronization: 1. Enter the address of the NTP Server 1 or NTP Server 2.2. Click the Get GMT button to get GMT time from Internet if you have connected to Internet. )Note:This setting will be used for some time-based functions such as firewall. You must specify your time zone once you login to the router successfully, if not, the time limited on these functions will not take effect. ¾The time will be lost if the router is turned off.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 253 - ¾The router will obtain GMT automatically from Internet if it has already connected to Internet. 8.17.2 DiagnosticChoose menu “System Tools ė Diagnostic”, you can transact Ping or Traceroute function to check connectivity of your network in the following screen. Figure 8-86 Diagnostic Tools ¾Diagnostic Tool - Check the radio button to select one diagnostic too. xPing - This diagnostic tool troubleshoots connectivity, reachability, and name resolution to a given host or gateway. xTraceroute - This diagnostic tool tests the performance of a connection.)Note:You can use ping/traceroute to test both numeric IP address or domain name. If pinging/tracerouting the IP address is successful, but pinging/tracerouting the domain name is not, you might have a name resolution problem. In this case, ensure that the domain name you are specifying can be resolved by using Domain Name System (DNS) queries. ¾IP Address/Domain Name - Type the destination IP address (such as 202.108.22.5) or Domain name (such as www.baidu.com). ¾Pings Count - The number of Ping packets for a Ping connection. ¾Ping Packet Size - The size of Ping packet.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 254 - ¾Ping Timeout - Set the waiting time for the reply of each Ping packet. If there is no reply in the specified time, the connection is overtime. ¾Traceroute Max TTL - The max number of hops for a Traceroute connection.Click Start to check the connectivity of the Internet. The Diagnostic Results page displays the result of diagnosis. If the result is similar to the following screen, the connectivity of the Internet is fine. Figure 8-87 Diagnostic Results )Note:Only one user can use this tool at one time. "Ping Count", "Ping Packet Size" and "Ping Timeout" are Ping Parameters. "Traceroute Max TTL" is Traceroute Parameter. 8.17.3Firmware Upgrade The page allows you to upgrade the latest version firmware to keep your router up-to-date. Figure 8-88 Firmware Upgrade New firmware is posted at www.tp-link.com and can be downloaded for free. If the router is not experiencing difficulties, there is no need to upgrade firmware, unless the new firmware supports a new feature you need.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 255 - )Note:1. When you upgrade the router's firmware, you will lose current configuration settings, so make sure you backup the router’s settings before you upgrade its firmware. 2. Make sure that your computer is connected to the Internet through the cable when you upgrade the firmware. To upgrade through wireless connection is not allowed. 3. Set your IP address as static IP before upgrading. To upgrade the router's firmware, follow these instructions: 1. Download the latest firmware upgrade file from our website 2http://www.tp-link.com.2. Enter or select the path name where you save the downloaded file on the computer into the File blank. 3. Click the Upgrade button. ¾Firmware Version - Displays the current firmware version. ¾Hardware Version - Displays the current hardware version. The hardware version of the upgrade file must accord with the current hardware version. )Note:The firmware version must correspond to the hardware. The upgrade process takes a few minutes and the Router will restart automatically when the upgrade is completed. It is important to keep power on during the entire process. Loss of power during the upgrade could damage the Router. 8.17.4Factory Defaults This page allows you to restore the factory default settings for the router. Figure 8-89 Restore Factory Default Click the Restore button to reset all configuration settings to their default values. ¾The default User Name: admin ¾The default Password: admin ¾The default access: tplinklogin.net )Note:Any settings you have saved will be lost when the default settings are restored.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 256 - 8.17.5 Backup & Restore This page allows you to save current configuration of router as backup or restore the configuration file you saved before. Figure 8-90 Backup & Restore Configuration ¾Click the Backup button to save all configuration settings as a backup file in your local computer. ¾To restore the router's configuration, follow these instructions: xClick the Browse button to select the backup file which you want to restore. xClick the Restore button. )Note:The current configuration will be covered with the uploading configuration file. The restoration process lasts for 20 seconds and the router will restart automatically. Keep the router on during the restoring process to prevent any damage. 8.17.6 RebootThis page allows you to reboot the router. Figure 8-91 Reboot the router Click the Reboot button to reboot the router. Some settings of the router will take effect only after rebooting, which include:¾Change LAN IP Address. (System will reboot automatically) ¾MAC Clone (system will reboot automatically) ¾DHCP service function. ¾Static address assignment of DHCP server. ¾Web Service Port of the router.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 257 - ¾Upgrade the firmware of the router (system will reboot automatically). ¾Restore the router's settings to factory default (system will reboot automatically). 8.17.7 Password This page allows you to change the factory default user name and password of the router. Figure 8-92 Password It is recommended strongly that you change the factory default user name and password of the router. All users who try to access the router's Web-based utility or Quick Setup will be prompted )Note:The new user name and password must not exceed 14 characters in length and must not include any spaces. Enter the new Password twice to confirm it. Click the Save button when finished. Click the Clear All button to clear all.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 258 - 8.17.8System Log This page allows you to query the logs of the router. Figure 8-93 System Log ¾Refresh - Refresh the page to show the latest log list. ¾Save Log - Click to save all the logs in a txt file. ¾Mail Log - Click to send an email of current logs manually according to the address and validation information set in Mail Settings. The result will be shown in the later log soon. ¾Clear Log - All the logs will be deleted from this device permanently, not just from the page. 8.17.9 StatisticsThe Statistics page displays the network traffic of each PC in LAN, including total traffic and traffic of the last Packets Statistic interval seconds.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 259 - Figure 8-94 Statistics ¾Current Statistics Status - Enable or Disable. The default value is disabled. To enable, click the Enable button. If disabled, the function of DoS protection in Security settings will be ineffective. ¾Packets Statistics Interval - The default value is 10. Select a value between 5 and 60 seconds in the pull-down list. The Packets Statistic interval indicates the time section of the packets statistic. ¾Sorted Rules - Here displays sort as desired. Statistics Table: IP Address The IP Address displayed with statistics Packets The total amount of packets received and transmitted by the router. Total Bytes The total amount of bytes received and transmitted by the router. Packets The total amount of packets received and transmitted in the lastPackets Statistic interval seconds. Bytes The total amount of bytes received and transmitted in the last Packets Statistic interval seconds. ICMP Tx The total amount of the ICMP packets transmitted to WAN in the last Packets Statistic interval seconds. UDP Tx The total amount of the UDP packets transmitted to WAN in the last Packets Statistic interval seconds. CurrentTCP SYN Tx The total amount of the TCP SYN packets transmitted to WAN in the last Packets Statistic interval seconds. Click the Save button to save the Packets Statistic interval value. Click the Auto-refresh checkbox to refresh automatically. Click the Refresh button to refresh immediately.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 260 - Appendix A: FAQ 1. How do I configure the Router to access the Internet by ADSL users? 1) First, configure the ADSL Modem configured in RFC1483 bridge model. 2) Connect the Ethernet cable from your ADSL Modem to the WAN port on the Router. The telephone cord plugs into the Line port of the ADSL Modem. 3) Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “PPPoE/Russia PPPoE” for WAN Connection Type. Type user name in the “User Name” field and password in the “Password” field and the “Confirm Password” field, and finish it by clicking Connect.Figure A-1 PPPoE Connection Type 4) If your ADSL lease is in “pay-according-time” mode, select “Connect on Demand” or “Connect Manually” for Internet connection mode. Type an appropriate number for “Max Idle Time” to avoid wasting paid time. Otherwise, you can select “Auto-connecting” for Internet connection mode. Figure A-2 PPPoE Connection Mode )Note:1. Sometimes the connection cannot be disconnected although you specify a time to Max Idle Time, since some applications is visiting the Internet continually in the background. 2. If you are a Cable user, please configure the Router following the above steps.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 261 - 2. How do I configure the Router to access the Internet by Ethernet users? 1) Log in to the Router, click the “Network” menu on the left of your browser, and click "WAN" submenu. On the WAN page, select “Dynamic IP” for "WAN Connection Type", finish by clicking Save.2) Some ISPs require that you register the MAC Address of your adapter, which is connected to your cable/DSL Modem during installation. If your ISP requires MAC register, log in to the Router and click the "Network" menu link on the left of your browser, and then click "MAC Clone" submenu link. On the "MAC Clone" page, if your PC’s MAC address is proper MAC address, click the Clone MAC Address button and your PC’s MAC address will fill in the "WAN MAC Address" field. Or else, type the MAC Address into the "WAN MAC Address" field. The format for the MAC Address is XX-XX-XX-XX-XX-XX. Then click the Save button. It will take effect after rebooting. Figure A-3 MAC Clone 3. I want to use NetMeeting, what do I need to do? 1) If you start NetMeeting as a sponsor, you don’t need to do anything with the Router. 2) If you start as a response, you need to configure Virtual Server or DMZ Host and make sure the H323 ALG is enabled. 3) How to configure Virtual Server: Log in to the Router, click the “Forwarding” menu on the left of your browser, and click "Virtual Servers" submenu. On the "Virtual Servers"page, click Add New…. Then on the “Add or Modify a Virtual Server Entry” page, enter “1720” for the “Service Port” blank, and your IP address for the “IP Address” blank, taking 192.168.0.169 for an example, remember to Enable and Save.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 262 - Figure A-4 Virtual Servers Figure A-5 Add or Modify a Virtual server Entry )Note:Your opposite side should call your WAN IP, which is displayed on the “Status” page.4) How to enable DMZ Host: Log in to the Router, click the “Forwarding” menu on the left of your browser, and click "DMZ" submenu. On the "DMZ" page, click Enable radio button and type your IP address into the “DMZ Host IP Address” field, using 192.168.0.169 as an example, remember to click the Save button. Figure A-6 DMZ 4. I want to build a WEB Server on the LAN, what should I do? 1) Because the WEB Server port 80 will interfere with the WEB management port 80 on the Router, you must change the WEB management port number to avoid interference.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 263 - 2) To change the WEB management port number: Log in to the Router, click the “Security”menu on the left of your browser, and click "Remote Management" submenu. On the "Remote Management" page, type a port number except 80, such as 88, into the "Web Management Port" field. Click Save and reboot the Router. Figure A-7 Remote Management )Note:If the above configuration takes effect, configure to the Router by typing 192.168.0.188 (the Router’s LAN IP address: Web Management Port) in the address field of the Web browser. 3) Log in to the Router, click the “Forwarding” menu on the left of your browser, and click the "Virtual Servers" submenu. On the "Virtual Servers" page, click Add New…, then on the “Add or Modify a Virtual Server” page, enter “88” into the blank next to the “Service Port”, and your IP address next to the “IP Address”, assuming 192.168.0.188 for an example, remember to Enable and Save.Figure A-8 Virtual Servers
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 264 - Figure A-9 Add or Modify a Virtual server Entry 5. The wireless stations cannot connect to the Router. 1) Make sure the "Enable Wireless Router Radio" is checked. 2) Make sure that the wireless stations' SSID accord with the Router's SSID. 3) Make sure the wireless stations have right KEY for encryption when the Router is encrypted. 4) If the wireless connection is ready, but you can’t access the Router, check the IP Address of your wireless stations.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 265 - Appendix B: Configuring the PC In this section, we’ll introduce how to install and configure the TCP/IP correctly in Windows XP. First make sure your Ethernet Adapter is working, refer to the adapter’s manual if necessary. 1. Configure TCP/IP component 1) On the Windows taskbar, click the Start button, and then click Control Panel.2) Click the Network and Internet Connections icon, and then click on the Network Connections tab in the appearing window. 3) Right click the icon that showed below, select Properties on the prompt page. Figure B-0-1 4) In the prompt page that showed below, double click on the Internet Protocol (TCP/IP).
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 266 - Figure B-0-2 5) The following TCP/IP Properties window will display and the IP Address tab is open on this window by default. 6) Select Obtain an IP address automatically, Choose Obtain DNS server automatically, as shown in the Figure below:
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 267 - Figure B-0-3 )Note:For Windows 98 OS or before, the PC and Router may need to be restarted.7) Click OK to keep your settings.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 268 - Appendix C: Specifications GeneralStandards IEEE 802.11n, 802.11b, 802.11g Protocols TCP/IP, PPPoE, DHCP, ICMP, NAT, SNTP Port One 10/100Mbps LAN/WAN port One 10/100Mbps LAN port 10BASE-T: UTP category 3, 4, 5 cable (maximum 100m) EIA/TIA-568 100ȍ STP (maximum 100m) Cabling Type 100BASE-TX: UTP category 5, 5e cable (maximum 100m) EIA/TIA-568 100ȍ STP (maximum 100m) LED SYS Dimensions (L×W×H) 81mm x 71mm x 28mm Safety & Emissions FCC, CE Wireless Frequency Band 2.4~2.4835GHz Radio Data Rate 11n˖up to 150Mbps˄Automatic˅11g˖54/48/36/24/18/12/9/6M˄Automatic˅11b˖11/5.5/2/1M˄Automatic˅Frequency Expansion DSSS(Direct Sequence Spread Spectrum) Modulation DBPSK, DQPSK, CCK, 16-QAM, 64-QAM, BPSK, QPSK Security 64/128/152-bit WEP, WPA/WPA2, WPA2-PSK/WPA-PSK Sensitivity @PER 135M: -70dBm@10% PER 65M: -73dBm@10% PER 54M: -76dBm@10% PER 6M: -92dBm@10% PER Mode Wireless Router Mode, Access Point Mode, Repeater Mode, Client Mode, WISP Client Router Mode Environmental and Physical Operating : 0ć~40ć (32 ~104̧̧)Temperature Storage: -40ć~70ć(-40̧~158̧)Operating: 10% - 90% RH, Non-condensing HumidityStorage: 5% - 90% RH, Non-condensing
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 269 - Appendix D: Glossary ¾802.11n - 802.11n builds upon previous 802.11 standards by adding MIMO (multiple-input multiple-output). MIMO uses multiple transmitter and receiver antennas to allow for increased data throughput via spatial multiplexing and increased range by exploiting the spatial diversity, perhaps through coding schemes like Alamouti coding. The Enhanced Wireless Consortium (EWC) [3] was formed to help accelerate the IEEE 802.11n development process and promote a technology specification for interoperability of next-generation wireless local area networking (WLAN) products. ¾802.11b - The 802.11b standard specifies a wireless networking at 11 Mbps using direct-sequence spread-spectrum (DSSS) technology and operating in the unlicensed radio spectrum at 2.4GHz, and WEP encryption for security. 802.11b networks are also referred to as Wi-Fi networks. ¾802.11g - specification for wireless networking at 54 Mbps using direct-sequence spread-spectrum (DSSS) technology, using OFDM modulation and operating in the unlicensed radio spectrum at 2.4GHz, and backward compatibility with IEEE 802.11b devices, and WEP encryption for security. ¾DDNS (Dynamic Domain Name System) - The capability of assigning a fixed host and domain name to a dynamic Internet IP Address. ¾DHCP (Dynamic Host Configuration Protocol) - A protocol that automatically configure the TCP/IP parameters for the all the PC(s) that are connected to a DHCP server. ¾DMZ (Demilitarized Zone) - A Demilitarized Zone allows one local host to be exposed to the Internet for a special-purpose service such as Internet gaming or videoconferencing. ¾DNS (Domain Name System) – An Internet Service that translates the names of websites into IP addresses. ¾Domain Name - A descriptive name for an address or group of addresses on the Internet. ¾DSL (Digital Subscriber Line) - A technology that allows data to be sent or received over existing traditional phone lines. ¾ISP (Internet Service Provider) - A company that provides access to the Internet. ¾MTU (Maximum Transmission Unit)- The size in bytes of the largest packet that can be transmitted.¾NAT (Network Address Translation) - NAT technology translates IP addresses of a local area network to a different IP address for the Internet.
TL-WR710N 150Mbps Wireless N Mini Pocket Router - Advanced Edition- 270 - ¾PPPoE (Point to Point Protocol over Ethernet) - PPPoE is a protocol for connecting remote hosts to the Internet over an always-on connection by simulating a dial-up connection. ¾SSID - AService Set Identification is a thirty-two character (maximum) alphanumeric key identifying a wireless local area network. For the wireless devices in a network to communicate with each other, all devices must be configured with the same SSID. This is typically the configuration parameter for a wireless PC card. It corresponds to the ESSID in the wireless Access Point and to the wireless network name. ¾WEP (Wired Equivalent Privacy) - A data privacy mechanism based on a 64-bit or 128-bit or 152-bit shared key algorithm, as described in the IEEE 802.11 standard. ¾Wi-Fi - A trade name for the 802.11b wireless networking standard, given by the Wireless Ethernet Compatibility Alliance (WECA, see http://www.wi-fi.net), an industry standards group promoting interoperability among 802.11b devices. ¾WLAN (Wireless Local Area Network) - A group of computers and associated devices communicate with each other wirelessly, which network serving users are limited in a local area.

Navigation menu