TR Controls M7L M7 LTE Vehicle Telematics Unit User Manual General

Download:
Mirror Download [FCC.gov]
Document ID	3966994
Application ID	UfJ+rpFklp+/pFkptTPkpA==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.46kB (193287 bits)
Date Submitted	2018-08-17 00:00:00
Date Available	2018-08-17 00:00:00
Creation Date	2018-08-08 18:38:09
Producing Software	Adobe PDF Library 11.0
Document Lastmod	2018-08-08 18:38:12
Document Title	General
Document Creator	Acrobat PDFMaker 11 Word 版
Document Author:	jmitchell

M7
Installation
Guide
Please call
ZTR Connected Asset Technical Support
With any questions:
1-888-320-8332
M7 Installation Guide
This page was left blank intentionally.
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
2 of 20
May 29, 2018
M7 Installation Guide
ZTR Control Systems – M7 Device
[Regulatory and Compliance Statement Goes Here]
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
3 of 20
May 29, 2018
M7 Installation Guide
OWNERSHIP AND CONFIDENTIALITY
The Software, Software Materials and Printed Documents constitute proprietary property of ZTR
Control Systems (ZTR) and include trade secrets and confidential information of ZTR. Customer
acknowledges that it acquires only the right to use the Software and Software Materials as permitted
hereunder and does not acquire any ownership, right or title in or to the Software, the Software
Materials or any Third Party Software.
The customer acknowledges that the information contained on the Software, Software Materials and
Printed Documents could be used to the detriment of ZTR and that the disclosure could cause
irreparable harm to ZTR. Accordingly, the customer undertakes to treat confidentially all information
and not to disclose it to any third party.
No part of this document may be reproduced in any form or by any means, electronic or mechanical,
including photocopying or printing, without the express written permission of ZTR Control Systems.
The data and illustrations found in this book are not binding. ZTR Control Systems reserves the right
to modify its products in line with its policy of continuous product development. A notice of changes
may be released for any modifications that may significantly affect the user.
All ZTR Control Systems products, images and marketing materials are protected by various patents,
copyrights, and/or trademarks.
©2018 ZTR Control Systems, LLC All Rights Reserved. (06/26)
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
4 of 20
May 29, 2018
M7 Installation Guide
WARNINGS AND PRECAUTIONS
HANDLING LI-ION CELLS:
All M7 devices contain an internal Lithium-thionyl Chloride (Li-Ion) battery, and must be handled
properly during installation, normal use and removal.
Li-Ion cells contain a large amount of energy and react extremely violently when exposed to moisture
in the atmosphere. Risk of fire or explosion exists only if the battery is handled improperly and/or
abused mechanically, electrically or thermally. Proper handling means the battery must NOT be
subjected to the following conditions:
• Short circuit
• Puncturing
• Recharging
• Crushing
• Incineration
• Immersion in water
• Exposure to temperature exceeding rated limits
Care must be taken, especially during installation and decommissioning, to ensure the units are not
punctured or crushed.
In the event of battery ignition, use ONLY Class D fire extinguishers on the flame. DO NOT USE:
water, sand, CO2, Halon, dry powder, or soda ash extinguishers.
For more information, consult the manufacturer Safety Data Sheet (SDS) for standard Lithium Thinoyl
Chloride batteries.
DISPOSAL OF LI-ION CELLS:
Lithium Ion batteries are often subject to local, state or provincial laws and regulations regarding
disposal. They cannot be simply disposed of in the trash. Check with your local landfill/recycling
facility for hazardous waste disposal requirements and safe disposal options.
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
5 of 20
May 29, 2018
M7 Installation Guide
Introduction
This manual includes instructions for installation of the M7 monitoring system.
The general flow of the instructions are as follows:
1.
Installation Document Requirements
Page 7
2.
Electrical Requirements
Page 7
3.
Supplies
Page 8
4.
Location and Installation Considerations
Page 8
5.
Wiring
Page 9
6.
Testing
Page 9
Appendix A: Label Revision History
Page 10
Appendix B: Installation Guide Revision History
Page 11
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
6 of 20
May 29, 2018
M7 Installation Guide
The following instructions and any accompanying documentation, drawings and specifications
are the property of ZTR CONTROL SYSTEMS. They are issued in strict confidence and shall
not be reproduced, copied or used as the basis for sale or manufacture of any apparatus without
prior written permission from ZTR CONTROL SYSTEMS.
1. Installation Documents Requirements
For reference during the installation of the M7, please be sure to bring along the following
documents for your reference as needed:
•
•
•
•
Control panel Installation & Operation Manual relevant to your equipment package
Schematics of the asset you are working on, if applicable
M7 Installation Guide
The device installation may be nearby the body ,and the distance maybe less than 20 cm.
2. Electrical Requirements
The following lists the electrical requirements for power and signal connections that are necessary for
the M7 to operate.
•
Power Supply Operational Range:
o Battery Supply = 6 – 90V DC
•
Digital Input Signal Range:
o Logic High (true, ON) = 6 – 60V DC
o Logic Low (false, OFF) = -0.3 – 5V DC
•
Digital Output Signal Range:
o Sinks voltage signals between -0.3 – 60V DC @ 200mA
•
Analog Input Signal Range:
o Voltage = 0 – 60V DC
Or…
o Current = 4 – 20mA
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
7 of 20
May 29, 2018
M7 Installation Guide
3. Supplies
The following information will help you understand what comes in the install kit and also provide
suggestions on additional supplies you may need for installation.
A. Available M7 Telematics:
Your kit will include the following:
• M7
• M7 Installation Guide
B. What is Not Included in the Kit:
•
The following are optional supplies that are not provided in this kit which you may need to
use during the installation of the device:
o Cable Ties
o Cable Tie Anchors
o Rubber Cable Gland
4. Location and Installation Considerations
• The M7 device will need to transmit cellular signals, as well as receive GPS positioning signals.
When looking for mounting locations, you want to find a location that will allow these
transmissions freely.
• Optimal mounting locations include:
o Horizontally mounted under fiberglass or plastic hood
o Horizontally mounted on top side of the equipment, facing the sky
• Although these optimal locations may not be easily achieved in some equipment, the M7 may
be mounted in other areas and orientations:
o Vertically on the side of the machine
o Inside the equipment/machine with open view to the sky
 Ie. Operator Cab
:IMPORTANT NOTE:
Avoid locations that limit communications such as inside metal control cabinets and areas
completely surrounded by metal.
Mount M7 in a location that does not expose it to potential physical damage when equipment
is in normal use.
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
8 of 20
May 29, 2018
M7 Installation Guide
5. Wiring
The M7 has a 36 inch wire harness with loose wires at the end. Figure 1 outlines the wire designations of
this wire harness. Refer to section 2: Electrical Requirements for more in-depth electrical requirements
that must be met for each relevant connection while wiring the M7 into your asset.
Batt + (6V to 90V DC)
Batt – (0 VDC)
BND
Input 1
Input 2
Analog 1
Output 1
Serial RX
Serial TX
Input 3
CAN-High – J1939
CAN-Low – J1939
Figure 1: 12-Pin Connector Pin References
6. Testing
With the M7 connected and powered up, confirm that the LED’s from Figure 2 illuminate.
YELLOW = Cell
GREEN = GPS
BLUE = Bluetooth
RED = Diagnostic
Figure 2: M7 Status Indicators
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
9 of 20
May 29, 2018
M7 Installation Guide
Appendix A: Label Revision History
This section will illustrate any changes to the product label as a result of a revision/update.
Revision:
Date: (MM/DD/YYYY)
05/29/2018
Author:
C. Bolte
Reason:
Initial release
FCC STATEMENTS
WARNING: Changes or modifications to this unit not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help.
SAR：
The radiated output power of this device is below the FCC radio frequency exposure limits. Nevertheless, the
device should be used in such a manner that the potential for human contact is minimized during normal
operation.
The exposure standard for wireless devices employs a unit of measurement known as the Specific Absorption
Rate, or SAR. The SAR limit set by the FCC is 1.6 W/Kg. Tests for SAR are conducted using standard
operating positions accepted by the FCC with the device transmitting at its highest certified power level in all
tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR
level of the device while operating can be well below the maximum value. This is because the device is
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
10 of 20
May 29, 2018
M7 Installation Guide
designed to operate at multiple power levels so as to use only the power required to reach the network. In
general, the closer you are to a wireless base station antenna, the lower the power output. To avoid the
possibility of exceeding the FCC radio frequency exposure limits, human proximity to the antenna should be
minimized.
INDUSTRY CANADA
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions: (1) this device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, meme si le
brouillage est susceptible d'en compromettre le fonctionnement
Title:
Author:
M7 Installation Guide
Christopher R. Boltë
PN:
VER:
111651
1.0
Page:
Date:
11 of 20
May 29, 2018
M7 Installation Guide
Appendix B: Installation Guide Revision History
This section will detail any changes to the content of this document as a result of a
revision/update.
Revision:
1.0
Title:
Author:
Date:
(MM/DD/YYYY)
05/29/2018
M7 Installation Guide
Christopher R. Boltë
Author:
Reason:
C. Bolte
Initial release
PN:
VER:
111651
1.0
Page:
Date:
12 of 20
May 29, 2018

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Author                          : jmitchell
Comments                        : 
Company                         : ZTR Control Systems
Create Date                     : 2018:08:08 18:38:09+08:00
Modify Date                     : 2018:08:08 18:38:12+08:00
Revision                        : Rev 1
Source Modified                 : D:20180808103805
Subject                         : 
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c006 80.159825, 2016/09/16-03:31:08
Metadata Date                   : 2018:08:08 18:38:12+08:00
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Document ID                     : uuid:9e3649b1-b36d-455c-8949-5ce3b91211ae
Instance ID                     : uuid:3e0327bc-d977-4688-8aa9-cf31916b5e80
Format                          : application/pdf
Title                           : General
Description                     : 
Creator                         : jmitchell
Producer                        : Adobe PDF Library 11.0
Keywords                        : 
Page Layout                     : OneColumn
Page Count                      : 12

EXIF Metadata provided by EXIF.tools