User Manual.pdf
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 1803242 |
| Application ID | +Ce1/bJHQ5XVOi7RzU+Eig== |
| Document Description | User Manual.pdf |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 22.67kB (283403 bits) |
| Date Submitted | 2012-09-27 00:00:00 |
| Date Available | 2012-09-27 00:00:00 |
| Creation Date | 2010-11-10 13:09:09 |
| Producing Software | Acrobat Distiller 8.1.0 (Windows) |
| Document Lastmod | 2012-09-27 15:05:18 |
| Document Title | untitled |
| Document Creator | PScript5.dll Version 5.2 |
| Document Author: | sam |
User Manual
Product User Manual
Model Number: GLM-300
Wireless N module
ALPHA Proprietary and Confidential Information
Introduction
This module is the wireless networking device based on 802.11b/g technology and compatible for
interoperability with 802.11n devices. This device provides up to 150Mbps transfer rate in the wireless
network and let users access the Internet resource, sharing file, and email quickly and your wireless
communications are protected by up to WPA2 encryption, so your data stays secure.
The extremely small design makes it easy to install into new or existing wireless device and lets
you to connect wirelessly to your network. It gives you the ability to roam at home or in the office
without wires.
Features
Compatible with IEEE 802.11b/g and 802.11n Standard for 2.4GHz Wireless
SoC solution combines 802.11n draft compliant 1T1R MAC/BBP/RF
Up to 150Mbps High-Speed PHY transfer rate on the wireless LAN interface
Works with All Existing Network Infrastructure.
Compatible with Wi-Fi Wireless Products and Services.
Capable of 64/128-Bit WEP, 256bit WPA and WPA2 Encryption
One I-PEX Connectors for External Antenna
Rich hardware interfaces (SPI/I2S/I2C/UART) to enable many possible applications.
Support IEEE 802.3 full duplex flow control
Support USB host mode
System Hardware
Processor : Ralink RT-3050 Single Chip SoC 320MHz CPU CLK
MIPS 24KEc 320MHz with 32KB I cache/16KB D cache
Embedded 1Tx1R 2.4G CMOS RF
Chipset maximum consumption 1.45W
802.11n 1T1R MAC/BBP
1 port 10/100Mbps PHY
16 bit 106MHz SDRAM
Support 16 bit NOR FLASH (up-to 8 Mbytes)
SDRAM: 32M Byte (16Mx16)
Flash ROM: 4M Byte (2Mx16)
3.3V DC switching type power adapter
Interface : 1x 10/100 Base-T LAN port
Other interface : UART, JTAG, GPIOs, WPS button, reset button
Power Requirement:
Operating Voltage: 3.3V DC
Output power: 22c;!2:/:eCn!
22h;!35/6eCn!
913/22o!)31NI{*;!35/3eCn!
913/22o!)51NI{*;!35/3eCn!
System Software
STANDARDS
z IEEE 802.11b/g
z IEEE 802.11n draft 2.0
z IEEE 802.3
z IEEE 802.3u
z System use Linux 2.6.
WIRELESS SECURITY
z WEP (64/128 bit)
z WPA / WPA2
z QOS- WMM, WMM Power Save
Physical dimensions & Environmental
Dimensions: 46mm(L) x 40mm(W) x 5.6mm(H)
Operation Temperature: 0к~40к ( 32л to 104л)
* Recommend operating under the condition of good airflow
Storage Temperature: -25к~55к (-13л to 131л)
Humidity: 5%~95% non-condensing.
* Environmental factors may affect actual range
Safety and Emission (Base on region and customer’s request)
EMI:
FCC15C/
classFCC
B, MPE/
CE lass
B LP0002
EMI: FCC
NCC
Safety: UL, TUV
PIN Description
TBD
PCB Dimension
PCBA dimension : TBD
mm(W) x
PCB dimenstion: 46mm(L)
------END------
mm(H)
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to
provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna
and users, and
2) The transmitter module may not be co-located with any other transmitter or
antenna.
As long as 2 conditions above are met, further transmitter test will not be required.
However, the OEM integrator is still responsible for testing their end-product for any
additional compliance requirements required with this module installed
IMPORTANT NOTE: In the event that these conditions can not be met (for example
certain laptop configurations or co-location with another transmitter), then the FCC
authorization is no longer considered valid and the FCC ID can not be used on the final
product. In these circumstances, the OEM integrator will be responsible for
re-evaluating the end product (including the transmitter) and obtaining a separate FCC
authorization.
End Product Labeling
This transmitter module is authorized only for use in device where the antenna may be
installed such that 20 cm may be maintained between the antenna and users. The final
end product must be labeled in a visible area with the following: “Contains FCC ID:
XU8GLM300”. The grantee's FCC ID can be used only when all FCC compliance
requirements are met.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end user
regarding how to install or remove this RF module in the user’s manual of the end
product which integrates this module.
The end user manual shall include all required regulatory information/warning as show
in this manual.
以下警語適用台灣地區
經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自
變更頻率、加大功率或變更原設計之特性及功能。
低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，
應立即停用，並改善至無干擾時方得繼續使用。前項合法通信，指依電信法規定
作業之無線電通信。低功率射頻電機須忍受合法通信或工業、科學及醫療用電波
輻射性電機設備之干擾。
Note: 1. 本模組於取得認證後將依規定於模組本體標示審驗合格標籤 2.
於平台上標示「本產品內含射頻模組:
系統廠商應
XXXyyyLPDzzzz-x (NCC ID) 」字樣
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Encryption : Standard V2.3 (128-bit) User Access : Print, Copy, Extract, Assemble XMP Toolkit : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39 Modify Date : 2012:09:27 15:05:18+08:00 Create Date : 2010:11:10 13:09:09+08:00 Metadata Date : 2012:09:27 15:05:18+08:00 Creator Tool : PScript5.dll Version 5.2 Format : application/pdf Title : untitled Creator : sam Document ID : uuid:9161fbb7-ea2b-4d34-a4cb-6d2237ccbfd9 Instance ID : uuid:dcc2a79a-a557-4742-a592-a021890c984d Producer : Acrobat Distiller 8.1.0 (Windows) Has XFA : No Page Count : 7 Author : samEXIF Metadata provided by EXIF.tools