TRENDNET TEW641PC 802.11n 2.0 Draft WLAN PC Card User Manual 5066623

TRENDNET, INC. 802.11n 2.0 Draft WLAN PC Card 5066623

Manual

i
ii Federal Communication Commission Interference Statement  This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.  These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful  interference  to  radio  communications.    However,  there  is  no  guarantee  that  interference  will  not  occur  in  a  particular installation.  If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:  -  Reorient or relocate the receiving antenna. -  Increase the separation between the equipment and receiver. -  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -  Consult the dealer or an experienced radio/TV technician for help.  FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.  This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. TEW-641PC  IMPORTANT NOTE: Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specific operating instructions for satisfying RF exposure compliance. To maintain compliance with FCC RF exposure compliance requirements, please follow operation instruction as documented in this manual.   This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  SAR compliance has been established in typical laptop computer(s) with CardBus slot, and product could be used in typical laptop computer with CardBus slot. Other application like handheld PC or similar device has not been verified and may not compliance with related RF exposure rule and such use shall be prohibited.   Europe – EU Declaration of Conformity This device complies  with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:  EN 60 950-1: 2006 Safety of Information Technology Equipment  EN 50392: (2004-01) Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz)  EN 300 328 V1.7.1: (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating  in  the  2,4  GHz  ISM  band  and  using  spread  spectrum  modulation  techniques;  Harmonized  EN  covering  essential requirements under article 3.2 of the R&TTE Directive
iii EN 301 489-1 V1.6.1: (2005-09) Electromagnetic  compatibility  and  Radio  Spectrum  Matters  (ERM);  ElectroMagnetic  Compatibility  (EMC)  standard  for  radio equipment and services; Part 1: Common technical requirements  EN 301 489-17 V1.2.1 (2002-08)  Electromagnetic  compatibility  and  Radio  spectrum  Matters  (ERM);  ElectroMagnetic  Compatibility  (EMC)  standard  for  radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.  In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.  This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France. TEW-643PI IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.  This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.  The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. Europe – EU Declaration of Conformity This device complies  with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:  EN 60 950-1: 2006 Safety of Information Technology Equipment  EN 50392: (2004-01) Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restrictions related to human exposure to electromagnetic fields (0 Hz - 300 GHz)  EN 300 328 V1.7.1: (2006-10) Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband Transmission systems; Data transmission equipment operating  in  the  2,4  GHz  ISM  band  and  using  spread  spectrum  modulation  techniques;  Harmonized  EN  covering  essential requirements under article 3.2 of the R&TTE Directive  EN 301 489-1 V1.6.1: (2005-09) Electromagnetic  compatibility  and  Radio  Spectrum  Matters  (ERM);  ElectroMagnetic  Compatibility  (EMC)  standard  for  radio equipment and services; Part 1: Common technical requirements  EN 301 489-17 V1.2.1 (2002-08)  Electromagnetic  compatibility  and  Radio  spectrum  Matters  (ERM);  ElectroMagnetic  Compatibility  (EMC)  standard  for  radio equipment and services; Part 17: Specific conditions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipment
iv This device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restrictive use applies.  In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services.  This device may not be used for setting up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed information the end-user should contact the national spectrum authority in France.   0560  Česky [Czech] [Jméno výrobce] tímto prohlašuje, že tento [typ zařízení] je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES. Dansk [Danish]  Undertegnede  [fabrikantens  navn]  erklærer  herved,  at  følgende  udstyr  [udstyrets  typebetegnelse] overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. Deutsch [German]  Hiermit  erklärt  [Name  des  Herstellers],  dass  sich  das  Gerät  [Gerätetyp]  in  Übereinstimmung  mit  den grundlegenden  Anforderungen und  den übrigen einschlägigen Bestimmungen der Richtlinie  1999/5/EG befindet. Eesti [Estonian]  Käesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tüüp = type of equipment] vastavust  direktiivi  1999/5/EÜ  põhinõuetele ja  nimetatud  direktiivist tulenevatele  teistele  asjakohastele sätetele. English  Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Español [Spanish]  Por  medio  de  la  presente  [nombre  del  fabricante]  declara  que  el  [clase  de  equipo]  cumple  con  los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE. Ελληνική [Greek] ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ [name of manufacturer] ∆ΗΛΩΝΕΙ ΟΤΙ [type of equipment] ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩ∆ΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ∆ΙΑΤΑΞΕΙΣ ΤΗΣ Ο∆ΗΓΙΑΣ 1999/5/ΕΚ. Français [French]  Par la présente [nom du fabricant] déclare que l'appareil [type d'appareil] est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano [Italian]  Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio] è conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski [Latvian]  Ar šo [name of manufacturer  / izgatavotāja nosaukums] deklarē, ka [type of equipment / iekārtas tips] atbilst Direktīvas 1999/5/EK būtiskajām prasībām un citiem ar to saistītajiem noteikumiem. Lietuvių [Lithuanian]   Šiuo [manufacturer  name] deklaruoja,  kad  šis  [equipment type]  atitinka esminius reikalavimus ir  kitas 1999/5/EB Direktyvos nuostatas. Nederlands [Dutch]  Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti [Maltese]  Hawnhekk,  [isem  tal-manifattur],  jiddikjara  li  dan  [il-mudel  tal-prodott]  jikkonforma  mal-ħtiġijiet essenzjali u ma provvedimenti oħrajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar  Alulírott, [gyártó neve] nyilatkozom, hogy a [... típus] megfelel a vonatkozó alapvetõ követelményeknek
v [Hungarian]  és az 1999/5/EC irányelv egyéb elõírásainak. Polski [Polish]  Niniejszym [nazwa producenta] oświadcza, że [nazwa wyrobu] jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Português [Portuguese] [Nome do fabricante] declara que este [tipo de equipamento] está conforme com os requisitos essenciais e outras disposições da Directiva 1999/5/CE. Slovensko [Slovenian]  [Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 1999/5/ES. Slovensky [Slovak]  [Meno  výrobcu]  týmto  vyhlasuje,  že  [typ  zariadenia]  spĺňa  základné  požiadavky  a  všetky  príslušné ustanovenia Smernice 1999/5/ES. Suomi [Finnish]  [Valmistaja = manufacturer] vakuuttaa täten että [type of equipment = laitteen tyyppimerkintä] tyyppinen laite  on  direktiivin  1999/5/EY  oleellisten  vaatimusten  ja  sitä  koskevien  direktiivin  muiden  ehtojen mukainen. Svenska [Swedish]  Härmed  intygar  [företag]  att  denna  [utrustningstyp]  står  I  överensstämmelse  med  de  väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direktiv 1999/5/EG.
vi TABLE OF CONTENT Introduction................................................................................................1 Overview of this User’s Guide .................................................................................1 Unpacking and Setup .................................................................................2 Unpacking.................................................................................................................2 Setup..........................................................................................................................2 IDentifying external components...............................................................3 LED...........................................................................................................................3 Check the installation................................................................................................3 Software Installation ..................................................................................4 Windows Based Utility Installation..........................................................................4 Wireless Utility Setting..............................................................................6 Link Information.......................................................................................................6 Configuration ............................................................................................................7 Site Survey ..............................................................................................................10 Profile......................................................................................................................11 WPS.........................................................................................................................12 About.......................................................................................................................16 Technical Specifications ..........................................................................17
1 INTRODUCTION Congratulations on your purchase of this 802.11n Wireless LAN Adapter  This manual contains detailed instructions regarding the operation of this product. Please keep this manual for future reference. With  the  802.11n  Wireless  LAN  Adapter,  a  desktop  or  laptop  computer  can communicate with another computer wirelessly. An easy-to-use utility is bundled with  the  802.11n  Wireless  LAN  Adapter  for  configuration,  monitoring,  and diagnostic purposes.  The 802.11n Wireless LAN Adapter can provides wireless speed wireless speed up 300Mbps RX PHY Rate,150Mbps TX PHY Rate. The  802.11n  Wireless  LAN  Adapter  provides  users  with  access  to  real-time information anywhere in their organization. The mobility of the 802.11n Wireless LAN PCI Adapter provides productivity and service, which are not available under wired  networks.  The  802.11n  Wireless  LAN  CardBus  Adapter  can  easily  adapt from  peer-to-peer  networks,  suitable  for  a  small  number  of  users,  to  full infrastructure networks of thousands  of users that  allow  roaming around a broad area.  Overview of this User’s Guide Introduction. Describes the 802.11n Wireless LAN Adapter and its features. Unpacking  and  Setup.    Helps  you  get  started  with  the  basic  installation  of  the  802.11n Wireless LAN Adapter. Hardware Installation.  Describes the LED indicator on the Adapter. Software Installation.  Describes how to setup the driver and the utility setting. Technical Specifications. Lists the technical (general, physical and environmental) specifications of the 802.11n Wireless LAN Adapter.
2 UNPACKING AND SETUP This section provides unpacking and setup information for the Wireless N CardBus Adapter or PCI Adapter. Unpacking The box should contain the following items:  One IEEE 802.11n Wireless LAN CardBus Adapter or PCI Adapter  One Driver & Utility CD-ROM If  any  item  is  found  missing  or  damaged,  please  contact  your  local  reseller  for replacement. Setup Before installation, check the following:  Make sure your computer is running at least a 300MHz or above processor with 256MB RAM or above  Visually inspect the PCI Adapter and make sure that it is fully plugged in to the PCI slot. (TEW-643PI)  Visually inspect the CardBus Adapter and make sure that it is fully plugged in to the PCMCIAI slot. (TEW-641PC)  The operating system on your computer must be the following: Windows 2000 (Service Pack 4), XP (Service Pack 2), Windows Vista  A draft 802.11n or 802.11b/g access point.  Make sure the environment has minimal interference and obstructions.
3 IDENTIFYING EXTERNAL COMPONENTS LED  Link The Link LED indicator lighted green when the 802.11n Wireless LAN Adapter is connected to wireless network successfully.  ACT (Activity) The ACT LED indicator blinking green when the 802.11n Wireless LAN Adapter is transmitting or receiving data. Check the installation The LEDs of the Wireless LAN Adapter are clearly visible and the status of the network link can be seen instantly:  TEW-641PC 1. Once  the  device  is  plugged  to  the  station’s  PCMCIA  slot,  the  LED  of  the Wireless LAN Adapter will light up indicating a normal status. 2. When  the  device  plugged  to  the  station’s  PCMCIA  slot  and  the  driver  was installed, the ACT will start alternate blinking, it means that the device is starting to scan the wireless devices near the Wireless LAN Adapter. 3. While the Wireless LAN Adapter linked up and transmitting data to the Access Point or to other Wireless LAN station, the Link LED will lighted green.  TEW-643PI  1. Once the device is plugged to the station’s PCI slot, the LED of the Wireless LAN Adapter will light up indicating a normal status. 2. When the device plugged to the station’s PCI slot and the driver was installed, the ACT will start alternate blinking, it means that the device is starting to scan the wireless devices near the Wireless LAN Adapter. 3. While the Wireless LAN Adapter linked up and transmitting data to the Access Point or to other Wireless LAN station, the Link LED will lighted green.
4 SOFTWARE INSTALLATION This section describes how to install the driver and utility for the 802.11n Wireless LAN Adapter. Windows Based Utility Installation 1) Insert the Utility and Driver CD-ROM into your computer’s CD-ROM Drive and then click Install Utility.   2) Follow the InstallShield Wizard Instructions
5  3) Click Finish to restart the computer.   4) Plug the TEW-641PC into an available CardBus slot or TEW-643PI in to an available PCI slot on your computer. (Please follow the Quick Installation Guide to install the driver)
6 WIRELESS UTILITY SETTING The user can configure the wireless settings using the Wireless Adapter Configuration Utility.  Double-click the utility icon that appears in the taskbar.   The Wireless Adapter Configuration Utility is divided into six sections: Link Info, Configuration, Site Survey, Profile, WPS and About.  Link Information This is the default screen after launching the Utility program.   Status: Shows the associated BSSID, which can be used to identify the wireless access point. SSID: Shows the current SSID, which must be the same on the wireless client and AP in order for communication to be established. Frequency: Shows the current frequency used for the wireless network. Wireless Mode: Shows the current wireless mode used for wireless communication. Encryption: Shows the current encryption mode used on the wireless network. TxRate: Shows the current data rate used for transmitting.
7 Channel: Shows the current channel for communication. Note::::For FCC domain device, you can only select Channel 1~11.             For ETSI domain device, you can only select Channel 1~13. Link Quality: Shows the link quality of the Wireless N CardBus Adapter with the Access Point when operating under Infrastructure mode. Signal Strength: Shows the wireless signal strength of the connection between the  Wireless N CardBus Adapter with the Access Point. Data Rate: Shows the statistics of data transfer, and the calculation is based on the number of packets transmitted and received.  Configuration This screen is where you set the basic wireless settings for the Wireless N CardBus Adapter.    Profile Name: Shows the Profile Name. SSID: Service Set Identifier, which is a unique name shared among all clients in a wireless network. The SSID must be identical for each client in the wireless network. Wireless Mode: There are two modes available for selection
8 ●  Infrastructure – to establish wireless communication with the LAN and other wireless clients through the use of Access Points. ●  Ad-Hoc – to establish point-to-point wireless communication directly with other wireless client devices. Authtication:  The  following  options  are  available:  Open  System,  Shared  Key, WPA-PSK, WPA2-PSK, WPA EAP-TLS, WPA2 EPA-TLS .  Select Open System, Shared Key for WEP data encryption feature.  Open or Shared Key Open System and Shared Key require the user to set a WEP key to exchange data with other wireless clients that have the same WEP key.  Default Key: select one of the 4 keys to use.  Network Key: choose the encryption way, either in HEX or ASCII formats, and enter the password in the blank space.   Key Length: select 64 or 128 bits as the length of the keys Key Format: HEX or ASCII  WPA-PSK / WPA2-PSK If using the WPA-PSK/WPA2-PSK authentication method, please select the Encryption type for TKIP or AES then enter the Passphrase key. The minimum length is 8 characters.
9   WPA EAP-TLS If using the WPA/WPA2 EAP-TLS authentication method, please select the Encryption type for TKIP or AES then select the WPA/WPA2 Certificate from drop down list.
10 Site Survey This screen allows the user to scan for available wireless networks (wireless clients and Access Points).  It also allows the user to establish wireless communications with an available wireless network.   Available Network – displays the wireless networks (wireless clients and access points) that are within range.  Select any one of the wireless networks by double-clicking on it or clicking  on the “Connect” button. Click the “Refresh” button to scan for available networks.
11 Profile Profile – The user can create and manage the created profiles for home, work or public areas. By double-clicking on one of the created profile, the setting will adjust to the specific setting such as SSID, channel, and encryption as saved by that particular profile. Add: Adds a profile. The following screen will appear. The user can enter the necessary information required for accessing Access Points or Wireless Router Remove: Deletes the selected profile Edit: Edit an exist profile. The screen will back to profile. Edit the SSID and select the  Wireless  Mode,  Authentication  and  Encryption  then  click  Apply  to  save  the profile. When the Profile name was changed, a new profile will be added in the list. Connect: Selected a profile from list then click the Connect to connecting to the wireless network with the profile setting.
 12 WPS WiFi Protected Setup (WPS) is an optional certification program from the Wi-Fi Alliance that is designed to ease the task of setting up and configuring security on a wireless network. There are two methods used in the WPS as below instruction.  Push the button on my access point Using  the  WPS  configuration  with  the  “Push  the  button  on  my  access  point” method, the configuration steps as below: 1) Selected the “Push the button on my access point”.  2) Push the WPS configuration button on your wireless access point or router. 3) Cliek the Next button start the WPS configuration.
13 4) If the WPS configuration was successful, the follow window will show on.  5) If the WPS configuration was failed, the follow window will show on.
 14 Enter a PIN into my access point Using the WPS configuration with the “Enter a PIN into my access point” method, the configuration steps as below: 1) Selected the “Enter a PIN into my access point”, the PIN will be show on the button of the windows.   2) Enter the PIN code into the WPS “Clint PIN number” of you wireless access point or router then click the  Start PIN button, the wireless access point or router will start the WPS configuration process.  3) Selected  a  wireless  access  point  or  router  which  one  will  be  connecting  then click the Next button start the WPS configuration. If the “Automatically select the network” was checked, the setup step will be skip.
15   4) If the WPS configuration was successful, the follow window will show on.   5) If the WPS configuration was failed, the follow window will show on.
16 About  This screen displays information about the Wireless N CardBus Adapter, such as the Driver and Utility version.  When a new version of the utility becomes available for upgrade, users will be able to identify by version numbers.
17 TECHNICAL SPECIFICATIONS  TEW-641PC (Wireless N PC Card)  Hardware Interface  32-Bit 3.3V CardBus Type II card Standards IEEE 802.11b, IEEE 802.11g and IEEE 802.11n (draft 2.0)  LED Indicator PWR (power), NET (“link”, “activity”) Power Consumption Receive mode: 550mA (max) ; Transmit mode: 600mA (max) Supported OS  Windows XP(32/64-bit)/Vista (32/64-bit) Dimensions (LxWxH) 120 x  54 x 3mm (4.7 x 2.1 x 0.13 inches) Weight 40g (1.4oz) Temperature Operating: 0° ~ 40° C (32° ~ 104° F); Storage: -10° ~ 70° C (14° ~ 158° F) Humidity 10% ~ 90% max (non-condensing) Certification FCC, CE Wireless Module Technique DBPSK/DQPSK/CCK/OFDM (BPSK/WPSK/16-QAM/64-QAM) Antenna Built-in 2 on board antennas Frequency 2.412 ~ 2.484 GHz   Media Access Protocol CSMA/CA Data  Rate  (auto fallback)  802.11b: 11Mbps, 5.5Mbps, 2Mbps, and 1Mbps 802.11g: 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps and 6Mbps 802.11n: up to 300Mbps (RX)/150Mbps(TX) Output Power  802.11b: 17dBm (typical)  802.11g: 16dBm (typical) 802.11n : 15dBm (typical)  Receiving Sensitivity  802.11b: -84dBm (typical) at 11Mpbs 802.11g: -68dBm (typical) at 54Mbps 802.11n: -65dBm at 135Mbps Encryption  64/128-bit WEP (Hex & ASCII), WPA/WPA2 (TKIP/AES), WPA-PSK/WPA2-PSK Channels  1~11 (FCC), 1~13 (ETSI)
18   TEW-643PI (Wireless N PCI Adapter)  Hardware Interface  32-Bit PCI Bus Standards IEEE 802.11b, IEEE 802.11g and IEEE 802.11n (draft 2.0)  LED Indicator PWR (power), NET (“link”, “activity”) Power Consumption Receive mode: 550mA (max) ; Transmit mode : 600mA (max)  Supported OS  Windows XP(32/64-bit)/Vista (32/64-Bit) Dimensions (LxW) 120 x  80mm (4.7 x 3.1in) Weight 75g (2.6oz) Temperature Operating: 0° ~ 40° C (32° ~ 104° F); Storage: -10° ~ 70° C (14° ~ 158° F) Humidity 10% ~ 90% max (non-condensing) Certification FCC, CE Wireless Module Technique DBPSK/DQPSK/CCK/OFDM (BPSK/WPSK/16-QAM/64-QAM) Antenna 2 x 2dBi dipole detachable antennas with Reverse SMA connector Frequency 2.412 ~ 2.484 GHz   Data  Rate  (auto fallback)  802.11b: 11Mbps, 5.5Mbps, 2Mbps, and 1Mbps 802.11g: 54Mbps, 48Mbps, 36Mbps, 24Mbps, 18Mbps, 12Mbps, 9Mbps and 6Mbps 802.11n: up to 300Mbps (RX)/150Mbps(TX) Output Power  17 dBm Receiving Sensitivity  802.11b: -84dBm (typical) at 11Mpbs 802.11g: -68dBm (typical) at 54Mbps 802.11n: -65dBm at 135Mbps Encryption  64/128-bit WEP (Hex & ASCII), WPA/WPA2 (TKIP/AES), WPA-PSK/WPA2-PSK Channels  1~11 (FCC), 1~13 (ETSI)                  Limited Warranty
19  TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase.    Wireless  Three years  If a  product  does not  operate  as warranted above  during the  applicable warranty period,  TRENDnet shall,  at  its option and  expense, repair  the defective product or deliver to customer an equivalent product to replace the defective item.  All products that are replaced will become the property of TRENDnet.  Replacement products may be new or reconditioned.  TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty.  There are no user serviceable parts inside the product.  Do not remove or attempt to service the product through any unauthorized service center.  This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual.  Warranty service may be obtained by contacting TRENDnet office within the applicable warranty period for a Return Material Authorization (RMA) number, accompanied by a copy of the dated proof of the purchase.  Products returned to TRENDnet must be pre-authorized by TRENDnet with RMA number marked on the outside of the package, and sent prepaid, insured and packaged appropriately for safe shipment.    WARRANTIES  EXCLUSIVE:  IF  THE  TRENDNET  PRODUCT  DOES  NOT  OPERATE  AS  WARRANTED  ABOVE,  THE  CUSTOMER’S  SOLE REMEDY  SHALL  BE,  AT  TRENDNET’S  OPTION,  REPAIR  OR  REPLACEMENT.  THE  FOREGOING  WARRANTIES  AND  REMEDIES  ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,  EITHER IN FACT OR  BY OPERATION OF LAW, STATUTORY  OR  OTHERWISE,  INCLUDING  WARRANTIES  OF  MERCHANTABILITY  AND  FITNESS  FOR  A  PARTICULAR  PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.  TRENDNET  SHALL  NOT  BE  LIABLE  UNDER  THIS  WARRANTY  IF  ITS  TESTING  AND  EXAMINATION  DISCLOSE  THAT  THE  ALLEGED DEFECT  IN  THE  PRODUCT  DOES  NOT  EXIST  OR  WAS  CAUSED  BY  CUSTOMER’S  OR  ANY  THIRD  PERSON’S  MISUSE,  NEGLECT, IMPROPER  INSTALLATION  OR  TESTING, UNAUTHORIZED  ATTEMPTS  TO  REPAIR OR MODIFY, OR  ANY  OTHER  CAUSE  BEYOND  THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.  LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY,  WHETHER  BASED  IN  CONTRACT  OR  TORT  (INCLUDING  NEGLIGENCE),  FOR  INCIDENTAL,  CONSEQUENTIAL,  INDIRECT, SPECIAL,  OR  PUNITIVE  DAMAGES  OF  ANY  KIND,  OR  FOR  LOSS  OF  REVENUE  OR  PROFITS,  LOSS  OF  BUSINESS,  LOSS  OF INFORMATION  OR  DATE,  OR  OTHER  FINANCIAL  LOSS  ARISING  OUT  OF  OR  IN  CONNECTION  WITH  THE  SALE,  INSTALLATION, MAINTENANCE,  USE,  PERFORMANCE,  FAILURE,  OR  INTERRUPTION  OF  THE  POSSIBILITY  OF  SUCH  DAMAGES,  AND  LIMITS  ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID,  AT TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.  Governing Law:  This Limited Warranty shall be governed by the laws of the state of California. Note: AC/DC Power Adapter, Cooling Fan, Cables and Power Supply carry 1-Year Warranty
20

Navigation menu