TRENDNET TEW715APO N150 Wireless Outdoor POE Access Point User Manual test 3

TRENDNET, Inc. N150 Wireless Outdoor POE Access Point test 3

UserManual.wiki >

TEW715APO User Manual

User Manual

TRENDnet User’s Guide Cover Page

© Copyright 2012 TRENDnet. All Rights Reserved. TRENDnet User’s Guide Table of Contents i Contents Product Overview ........................................................................... 3 Package Contents .......................................................................................................... 3 Features ......................................................................................................................... 3 Product Hardware Features ............................................................. 4 Application Diagram ...................................................................................................... 5 Creating a Network ........................................................................................................ 6 Wireless Performance Considerations .......................................................................... 6 Getting Started ............................................................................... 7 Connect wireless devices to your access point .............................................................. 8 Steps to improve wireless connectivity ......................................................................... 8 Configuration .................................................................................. 9 Access the management page ....................................................................................... 9 System Modes .............................................................................. 10 Bridge Mode ................................................................................. 10 AP Mode ...................................................................................................................... 11 Wireless Client Mode................................................................................................... 13 Bridge Mode ................................................................................................................ 16 AP Repeater Mode....................................................................................................... 18 Router Mode................................................................................. 20 AP Mode ...................................................................................................................... 21 Wireless Client Mode................................................................................................... 23 Bridge Mode ................................................................................................................ 26 AP Repeater Mode....................................................................................................... 28 Wireless Networking and Security ................................................. 30 How to choose the type of security for your wireless network .................................. 30 Secure your wireless network ..................................................................................... 31 Wireless access control ............................................................................................... 33 Advance Settings .......................................................................... 33 Change your IP address ............................................................................................... 33 Configure your Internet connection ............................................................................ 34 Setting time ................................................................................................................. 35 Advance wireless settings ............................................................................................ 35 Change your login password ....................................................................................... 36 Access Control .............................................................................. 37 Source IP Filtering ........................................................................................................ 37 Destination IP Filtering ................................................................................................ 37 Source Port Filtering .................................................................................................... 37 Destination Port Filtering ............................................................................................ 38 Port Fordwarding ......................................................................................................... 38 Open a device on your network to the Internet .......................................................... 39 DMZ ......................................................................................................................... 39 UDP Pass through ........................................................................................................ 39 Configure your log ....................................................................................................... 39 View your log ............................................................................................................... 39 Ping Watchdog ............................................................................................................ 40 Ping Watchdog ........................................................................................................ 40 WDS Data Rate Test ..................................................................................................... 40 Antenna Alignment ...................................................................................................... 41 Speed Test ................................................................................................................... 41 Remote Mangement ................................................................................................... 41 Coovachili .................................................................................................................... 43

© Copyright 2012 TRENDnet. All Rights Reserved. TRENDnet User’s Guide Table of Contents ii Upgrade Firmwre ......................................................................................................... 43 Backup and restore your router configuration settings .............................................. 44 Reset to factory defaults ............................................................................................. 45 Certificate configuration settings ................................................................................ 45 Device Information ...................................................................................................... 45 Associated Information ............................................................................................... 46 Statistics ....................................................................................................................... 47 ARP Table ..................................................................................................................... 47 Bridge Table ................................................................................................................. 47 DHCP Clients ................................................................................................................ 48 Network Activity .......................................................................................................... 48 Additional hardware installation ................................................... 48 Ground wire ................................................................................................................. 48 Using the optional external antenna ........................................................................... 49 Pole mounting ............................................................................................................. 49 Access Point Management Page Structure ..................................... 50 Technical Specifications................................................................. 51 Troubleshooting ............................................................................ 52 Appendix ...................................................................................... 53 Internet service types .................................................................................................. 55

© Copyright 2012 TRENDnet. All Rights Reserved. 3 TRENDnet User’s Guide TEW-715APO Product Overview Package Contents In addition to the access point, the package includes: • TEW-715APO • CD-ROM (User’s Guide) • Multi-Language Quick Installation Guide • Mounting hardware • Power Adapter (12V, 1A) • PoE Injector • Grounding Wire If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased. Features TRENDnet’s N150 Wireless Outdoor PoE Access Point, model TEW-715APO, provides high speed building-to-building networking with its built in dual polarization directional 8dBi antenna for distances up to 6 miles (10 km)*. Install an omni-directional antenna (with a N-Type connector), such as TRENDnet’s TEW-AO08O to provide blanket outdoor wireless coverage over a large area. A range of applications are facilitated with Access Point, Wireless Client, WDS, Bridge, CPE, and Repeater mode support. A durable IP-55 rated outdoor enclosure protects the device from inclement weather. Power for this unit is supplied by an included PoE injector, resulting in equipment and installation cost savings. Additional features include SNMP (v2c, v3), Spanning Tree, real time network activity tables, WPA/WPA2 encryption, MAC address filters, 16 virtual AP profiles, 802.1Q, 802.1X, mounting hardware, and GPS coordinate support. • 1 x 10/100Mbps Auto-MDIX LAN port • 1 x reset button • 1 x Reverse N-type connector for optional antenna configuration • LED indicators: Power, WLAN, LAN • Internal high powered 8Bi patch antenna directional antenna • Rugged IP55 rated weather proof housing • PoE compliant device • High speed data rates of up to 150Mbps based on IEEE 802.11n technology • Compliant with IEEE 802.11b/g standards • Supports Access Point (AP), Wireless Distribution System (WDS)/Bridge, Customer Premises Equipment (CPE), and AP + Repeater modes • Multiple SSID or Virtual Access Points with Layer 2 VLAN wireless client isolation • Access restriction with MAC filtering • Universal Plug and Play (UPnP) for auto discovery and support for device configuration of Internet applications • Complete wireless security with WPA/WPA2-RADIUS, WPA /WPA2-PSK, and WEP • Wi-Fi Multimedia (WMM) Quality of Service (QoS) data prioritization • Easy setup via Web browser using the latest versions of Internet Explorer, FireFox, and Safari • Supports SNMP (v2c and v3), Telnet, SSH, and HTTP/HTTPS management • Surface mounting hardware • Electrical ground cable • 3-year limited warranty

© Copyright 2012 TRENDnet. All Rights Reserved. 4 TRENDnet User’s Guide TEW-715APO *Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual data throughput and coverage will vary depending on interference, network traffic, building materials and other conditions. Product Hardware Features Access Point Side View • External Antenna (optional): N-Type connector for the option to connect an external antenna and not use the built in antenna. • Diagnostic LEDs: Provides device status. o Wireless Signal: Blinks green during wireless network activity.  Green (Good), Yellow (Moderate), Red (Poor) o LAN: Blinks green during network activity o Power: Solid green when the device has power • Ethernet port: 1x 10/100Mbps Auto-MDIX port. Connect the side marked “PoE” of PoE adapter to this port. Depending on the mode settings applied, the Ethernet port can function as the network WAN port or LAN port. Note:To access the Ethernet port, remove the bottom cap. • Reset button: Press and hold the reset button for 15seconds to reset the unit back the factory default settings. Note: To access the reset button, remove the bottom cap Access Point Front View with Bottom Cap Removed • Ethernet port: 1x 10/100Mbps Auto-MDIX port. Connect the side marked “PoE” of PoE adapter to this port. Depending on the mode settings applied, the Ethernet port can function as the network WAN port or LAN port • Reset button: Press and hold the reset button for 15seconds to reset the unit back the factory default settings. LAN Port Diagnostic LEDS Reset Button Ethernet Port Ethernet Port Reset Button

© Copyright 2012 TRENDnet. All Rights Reserved. 5 TRENDnet User’s Guide TEW-715APO PoE Adapter View • PoE: Provides power to the access point. Connect this side to the access point Ethernet port. • DC Power port: Powers up the PoE adapter. • LAN: Provides network connectivity to the access point and your network. Connect this side to your router or network. • Ground: Provides extra grounding connection to protect the access point. Application Diagram The access point is mounted a pole which is connected to the provided PoE adapter and then connected to your network switch or router. Wireless signals from the access point are broadcasted to each creating a Bridge/WDS connection, thereby providing network connection between both networks. PoE LAN DC Power Port Ground

© Copyright 2012 TRENDnet. All Rights Reserved. 6 TRENDnet User’s Guide TEW-715APO Creating a Network What is a network? A network is a group of computers or devices that can communicate with each other. A home network of more than one computer or device also typically includes Internet access, which requires a router. A typical home network may include multiple computers, a media player/server, a printer, a modem, and a router. A large home network may also have a switch, additional routers, access points, and many Internet-capable media devices such as TVs, game consoles, and Internet cameras. • Modem – Connects a computer or router to the Internet or ISP (Internet Service Provider). • Router – Connects multiple devices to the Internet. • Switch –Connect several wired network devices to your home network. Your router has a built-in network switch (the LAN port 1-4). If you have more wired network devices than available Ethernet ports on your router, you will need an additional switch to add more wired connections. How to set up a home network 1. For a network that includes Internet access, you’ll need: • Computers/devices with an Ethernet port (also called network port) or wireless networking capabilities. • A modem and Internet service to your home, provided by your ISP (modem typically supplied by your ISP). • A router to connect multiple devices to the Internet. 2. Make sure that your modem is working properly. Your modem is often provided by your Internet Service Provider (ISP) when you sign up for Internet service. If your modem is not working contact your ISP to verify functionality. 3. Set up your router. See “How to setup your router” below. 4. To connect additional wired computers or wired network devices to your network, see “Connect additional wired devices to your network” on page 11. 5. To set up wireless networking on your router, see “Wireless Networking and Security” on page 12. Wireless Performance Considerations There are a number of factors that can impact the range of wireless devices. 1. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose. 2. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them. 3. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal. 4. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapter’s site survey tool to determine the best antenna orientation for your wireless devices. 5. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position your wireless devices away from anything that generates RF noise, such as microwaves, radios and baby monitors. 6. Any device operating on the 2.4GHz frequency will cause interference. Devices such as 2.4GHz cordless phones or other wireless remotes operating on the 2.4GHz frequency can potentially drop the wireless signal. Although the phone may not be in use, the base can still transmit wireless signal. Move the phone’s base station as far away as possible from your wireless devices. If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional access points. The use of higher gain antennas may also provide the necessary coverage depending on the environment.

© Copyright 2012 TRENDnet. All Rights Reserved. 7 TRENDnet User’s Guide TEW-715APO Getting Started For a typical wireless setup at home or office when using the access point in AP mode, please do the following: Hardware Installation 1. Remove the bottom cap. 2. Plug a Network cable to the Ethernet port. 3. Slide the bottom cover back to the unit. 4. Plug an Ethernet cable to the access point and plug the other end of the cable to the side of the PoE adapter marked PoE. 5. Take another Ethernet cable and plug it on the side of the PoE adapter marked LAN, plug the other end of the cable to your network. 6. Verify that the following LED indicators on the access point: Power (Solid Green), LAN (Solid/Blinking Green) and WLAN (Blinking Green). 7. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and go to http://192.168.10.100. The access point will prompt you for a password. 8. Enter the default user name and password and then click Login. Default System Password: admin

© Copyright 2012 TRENDnet. All Rights Reserved. 8 TRENDnet User’s Guide TEW-715APO 9. Click the System button on the left side and then System Settings. 10. Select Bridge in the Mode drop down menu. 11. Click Apply button to save your setting. 12. Once the configuration is saved. Click the Wireless button on the left side and then Basic Settings. 13. Select AP in the Operation Mode pull down menu. 14. Enter your desired network name (SSID) of your wireless network in the Wireless Network Name and click Apply to save settings. Connect wireless devices to your access point A variety of wireless network devices can connect to your wireless network such as: • Wireless Laptop computers • Network media players • Wireless IP cameras • Smart Phones • Gaming Consoles • Internet enabled TVs Each device may have its own software utility for searching and connecting to available wireless networks, therefore, you must refer to the User’s Manual/Guide of your wireless client device to determine how to search and connect to this router’s wireless network. See the “Appendix” on page 53 for general information on connecting to a wireless network. Steps to improve wireless connectivity There are a number of factors that can impact the range of wireless devices. Follow these tips to help improve your wireless connectivity: 1. Keep the number of obstructions to a minimum. Each obstruction can reduce the range of a wireless device. Position the wireless devices in a manner that will minimize the amount of obstructions between them. a. For the widest coverage area, install your router near the center of your home, and near the ceiling, if possible. b. Avoid placing the router on or near metal objects (such as file cabinets and metal furniture), reflective surfaces (such as glass or mirrors), and masonry walls.

© Copyright 2012 TRENDnet. All Rights Reserved. 9 TRENDnet User’s Guide TEW-715APO c. Any obstruction can weaken the wireless signal (even non-metallic objects), so the fewer obstructions between the router and the wireless device, the better. d. Place the router in a location away from other electronics, motors, and fluorescent lighting. e. Many environmental variables can affect the router’s performance, so if your wireless signal is weak, place the router in several locations and test the signal strength to determine the ideal position. 2. Building materials can have a large impact on your wireless signal. In an indoor environment, try to position the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal. 3. Antenna orientation can also have a large impact on your wireless signal. Use the wireless adapter’s site survey tool to determine the best antenna orientation for your wireless devices. 4. Interference from devices that produce RF (radio frequency) noise can also impact your signal. Position your wireless devices away from anything that generates RF noise, such as microwaves, radios and baby monitors. If possible, upgrade wireless network interfaces (such as wireless cards in computers) from older wireless standards to 802.11n. If a wirelessly networked device uses an older standard, the performance of the entire wireless network may be slower. If you are still experiencing low or no signal consider repositioning the wireless devices or installing additional access points. Configuration Access the management page Note: The access point’s default management page http://192.168.10.100 is accessed through the use of your Internet web browser (e.g. Internet Explorer, Firefox, Chrome, Safari, Opera) and will be referenced frequently in this User’s Guide. 1. Open your web browser (e.g. Internet Explorer, Firefox, Safari, Chrome, or Opera) and go to http://192.168.10.100. The access point will prompt you for a password. 2. Enter the default user name and password and then click Login. Default System Password: admin

© Copyright 2012 TRENDnet. All Rights Reserved. 10 TRENDnet User’s Guide TEW-715APO System Modes The TEW-715APO access point supports two different types of system modes. Please verify carefully on which mode you would like the device to operate in to proper installation. • Bridge Mode: The devices operates as an access point with no WAN/Internet configuration. Below list the supported wireless modes when bridge is selected as the device system mode. o AP Mode: Creates a wireless network to your existing network. Device Ethernet port serves as a LAN (Local Area Network) port of the device o Wireless Client: Connects to any existing wireless network (similar to a wireless adapter). Device Ethernet port serves as a LAN (Local Area Network) port of the device o Bridge: Creates a wireless bridge connection with another access point. Ethernet port serves as a LAN (Local Area Network) port of the device o AP Repeater: Repeats the wireless signal of an existing wireless network. Device Ethernet port serves as a LAN (Local Area Network) port of the device • Router Mode: The device operates similar to a wireless router with WAN/Internet configuration. Below list the supported wireless modes when bridge is selected as the device system mode. o AP Mode: Creates a wireless network with your device (similar to w wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. o Wireless Client: Connects to any existing wireless network (similar to a wireless adapter) in which the wireless network the device is connecting to serves as your Internet connection. Ethernet port serves as a LAN (Local Area Network) port of the device and the wireless settings is based on your ISP (Internet Service Provider) connection. o Bridge: Creates a wireless network with your device (similar to a wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. o AP Repeater: Creates a wireless network with your device (similar to a wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. Bridge Mode Below describes the configuration settings when the TEW-715APO System Mode is set to Bridge. In this setting the Ethernet port of the TEW-715APO serves as a LAN (Local Area Network) connection. Configuration 1. Log into the management page (see “Access the management page” on page 9). 2. Your access point will prompt you for a user name and password. 3. Enter the default user name and password and then click Login. Default User Name: admin Default Password: admin 4. Click the System button on the left side and then System Settings. 5. Select Bridge in the Mode drop down menu. 6. Click Apply button to save your setting.

© Copyright 2012 TRENDnet. All Rights Reserved. 11 TRENDnet User’s Guide TEW-715APO 7. Click the Wireless button on the left side and then Basic Settings. 8. Select the mode you would like to apply Operation Mode pull down menu. • AP Mode: Creates a wireless network to your existing network. Device Ethernet port serves as a LAN (Local Area Network) port of the device • Wireless Client: Connects to any existing wireless network (similar to a wireless adapter). Device Ethernet port serves as a LAN (Local Area Network) port of the device • Bridge: Creates a wireless bridge connection with another access point. Ethernet port serves as a LAN (Local Area Network) port of the device • AP Repeater: Repeats the wireless signal of an existing wireless network. Device Ethernet port serves as a LAN (Local Area Network) port of the device AP Mode Wireless > Basic This section outlines available management options when the device System Setting is set to Bridge and the wireless Operation Mode is set to AP. Click Apply to save any changes.

© Copyright 2012 TRENDnet. All Rights Reserved. 12 TRENDnet User’s Guide TEW-715APO • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional information to operate the device as an access point. • Wireless Network Name (SSID): This acronym stands for Service Set Identifier and is the name of your wireless network. It differentiates your wireless network from others around you. By default, the access point broadcast TRENDnet715 as the wireless network name. If you choose to change the SSID, change it to a name that you can easily remember. You can click more to configure additional SSID. Please refer to pagexxxx • Broadcast SSID: o Enable: Access point will broadcast the your wireless network name (SSID), making it easier for wireless clients to find the wireless network. o Disable: Access point will not broadcast the wireless network name (SSID) and wireless clients will have to manually enter the wireless network to connect. • 802.11 Mode: If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate mode. If you have some devices that use a different transmission mode, choose the appropriate mode. o 802.11b/g mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will allow both wireless b and wireless g client to connect and access point, at 54Mbps for wireless g and share access at the same time. Although the wireless b/g operates in the 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. o 802.11b/g/n mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will only allow the use of wireless g client devices to connect and access point, 54Mbps for wireless g and up to 300Mbps* for wireless n and share access at the same time. Although the wireless b/g/n operates in the same 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless b/g/n) to connect and access at the same time. • HT protect: Enable HT (High Throughput) protect to ensure HT transmission with MAC mechanism. Under 802.11n mode, wireless client can be divided into HT STA and Non-HT STA, among which the one with HT protect enabled gets higher throughput. • Frequency (Channel): To manually set the channel on which the router will broadcast, uncheck Auto Channel, then click the drop-down list and select the desired Channel for wireless communication. The goal is to select the Channel that is least used by neighboring wireless networks. • Extension channel: When 20/40 channel bandwidth has been chosen, you should select extension channel to get higher throughput. • Channel Mode: Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more bandwidth, thus it might cause potential interference. • Antenna: By default, IEEE 802.11b/g/n Wireless CPE uses its built-in antenna for directional transmission; however, if you prefer to use an external antenna for your case-dependent applications, you can switch from “Internal (8 dBi)” to” External (N-Type)”. When External (N-Type) is selected, an Antenna Gain bar will appear to allow you specify the gain of the external antenna. The antenna gain calculates the TX power back off needed to remain in compliance with regulations. Please refer to External Antenna installation on page 49. o You are able to choose “External (N-Type)” only when you have well done installing the external antenna; otherwise, it might damage IEEE 802.11b/g/n Wireless CPE itself. o The maximum output power will vary depending on the country selected in order to comply with the local regulation. o The output power here is counted from the RF single chain only not including the 8dBi internal antenna. • Maximum Output power: Specify the signal transmission power. The higher the output power is, the wider the signal can cover, but the power consumption will be greater accordingly. • Data Rate: Usually “Auto” is preferred. Under this rate, the IEEE 802.11b/g/n Wireless CPE will automatically select the highest available rate to transmit. In some cases, however, like where there is no great demand for speed, you can have a relatively-low transmit rate for compromise of a long distance.

© Copyright 2012 TRENDnet. All Rights Reserved. 14 TRENDnet User’s Guide TEW-715APO • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional information to operate the device as an access point. • Site Survey: Click to scan and select available wireless networks. • Wireless Network Name (SSID): This acronym stands for Service Set Identifier and is the name of your wireless network. You can manually enter the wireless network you want to connect to or click “Site Survey” option to scan for available wireless networks around you. Please refer to pagexxx • Lock AP MAC: Enter the MAC address of the access point you are connected. • 802.11 Mode: If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate mode. If you have some devices that use a different transmission mode, choose the appropriate mode. o 802.11b/g mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will allow both wireless b and wireless g client to connect and access point, at 54Mbps for wireless g and share access at the same time. Although the wireless b/g operates in the 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. o 802.11b/g/n mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will only allow the use of wireless g client devices to connect and access point, 54Mbps for wireless g and up to 300Mbps* for wireless n and share access at the same time. Although the wireless b/g/n operates in the same 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless b/g/n) to connect and access at the same time. • Channel Mode: Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more bandwidth, thus it might cause potential interference. • Antenna: By default, IEEE 802.11b/g/n Wireless CPE uses its built-in antenna for directional transmission; however, if you prefer to use an external antenna for your case-dependent applications, you can switch from “Internal (8 dBi)” to” External (N-Type)”. When External (N-Type) is selected, an Antenna Gain bar will appear to allow you specify the gain of the external antenna. The antenna gain calculates the TX power back off needed to remain in compliance with regulations. Please refer to External Antenna installation on page 49. o You are able to choose “External (N-Type)” only when you have well done installing the external antenna; otherwise, it might damage IEEE 802.11b/g/n Wireless CPE itself. o The maximum output power will vary depending on the country selected in order to comply with the local regulation. o The output power here is counted from the RF single chain only not including the 8dBi internal antenna. • Maximum Output power: Specify the signal transmission power. The higher the output power is, the wider the signal can cover, but the power consumption will be greater accordingly. • Data Rate: Usually “Auto” is preferred. Under this rate, the IEEE 802.11b/g/n Wireless CPE will automatically select the highest available rate to transmit. In

© Copyright 2012 TRENDnet. All Rights Reserved. 16 TRENDnet User’s Guide TEW-715APO Bridge Mode Wireless > Basic Bridge or Wireless Distribution System (WDS) or Bridge uses the WDS protocol that is not defined as the standard thus compatibility issues between equipment from different vendors may arise. Moreover, Tree or Star shape network topology should be used in all WDS use-cases (i.e. if AP2 and AP3 are specified as the WDS peers of AP1, AP2 should not be specified as the WDS peer of AP3 and AP3 should not be specified as the WDS peer of AP2 in any case). Mesh and Ring network topologies are not supported by WDS and should be avoided in all the use cases. This section outlines available management options when the device System Setting is set to Bridge and the wireless Operation Mode is set to Bridge. Click Apply to save any changes. • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional information to operate the device as an access point. • 802.11 Mode: If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate mode. If you have some devices that use a different transmission mode, choose the appropriate mode. o 802.11b/g mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will allow both wireless b and wireless g client to connect and access point, at 54Mbps for wireless g and share access at the

© Copyright 2012 TRENDnet. All Rights Reserved. 17 TRENDnet User’s Guide TEW-715APO same time. Although the wireless b/g operates in the 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. o 802.11b/g/n mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will only allow the use of wireless g client devices to connect and access point, 54Mbps for wireless g and up to 300Mbps* for wireless n and share access at the same time. Although the wireless b/g/n operates in the same 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless b/g/n) to connect and access at the same time. • Frequency (Channel): To manually set the channel on which the router will broadcast, uncheck Auto Channel, then click the drop-down list and select the desired Channel for wireless communication. The goal is to select the Channel that is least used by neighboring wireless networks. • Extension channel: When 20/40 channel bandwidth has been chosen, you should select extension channel to get higher throughput. • Channel Mode: Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more bandwidth, thus it might cause potential interference. • Antenna: By default, IEEE 802.11b/g/n Wireless CPE uses its built-in antenna for directional transmission; however, if you prefer to use an external antenna for your case-dependent applications, you can switch from “Internal (8 dBi)” to” External (N-Type)”. When External (N-Type) is selected, an Antenna Gain bar will appear to allow you specify the gain of the external antenna. The antenna gain calculates the TX power back off needed to remain in compliance with regulations. Please refer to External Antenna installation on page 49. o You are able to choose “External (N-Type)” only when you have well done installing the external antenna; otherwise, it might damage IEEE 802.11b/g/n Wireless CPE itself. o The maximum output power will vary depending on the country selected in order to comply with the local regulation. o The output power here is counted from the RF single chain only not including the 8dBi internal antenna. • Maximum Output power: Specify the signal transmission power. The higher the output power is, the wider the signal can cover, but the power consumption will be greater accordingly. • Data Rate: Usually “Auto” is preferred. Under this rate, the IEEE 802.11b/g/n Wireless CPE will automatically select the highest available rate to transmit. In some cases, however, like where there is no great demand for speed, you can have a relatively-low transmit rate for compromise of a long distance. • Extension Channel Protection: This is to avoid conflict with other wireless network and boost the ability of your device to catch all 802.11g transmissions. However, it may decrease wireless network performance. Compared to CTS-Self; the transmission amount of CTS-RTS is much lower. Wireless >WDS Setting This section outlines the available management options under the WDS Settings of the Wireless button. WDS Settings is available only under Bridge and AP Repeater Mode. • WDS Separation: Enable separates all configured WDS AP to communicate with each other. • Remote AP: Enter the MAC address of the access point you want to WDS with. Note: You must enter the MAC address of every access point in the WDS network. Each wireless setting (SSID, channel, wireless encryption) must match on each access point in the WDS network.

© Copyright 2012 TRENDnet. All Rights Reserved. 18 TRENDnet User’s Guide TEW-715APO AP Repeater Mode Wireless > Basic. AP Repeater mode allows the access point to repeat a wireless signal of an existing wireless network. This section outlines available management options when the device System Setting is set to Bridge and the wireless Operation Mode is set to AP Repeater. Click Apply to save any changes. Note: The access point’s wireless settings must be configured with the exact wireless settings as the repeating signal (Network name, channel, wireless security, etc.) • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional information to operate the device as an access point. • Wireless Network Name (SSID): This acronym stands for Service Set Identifier and is the name of your wireless network. You can manually enter the wireless network you want to repeat. • Broadcast SSID: o Enable: Access point will broadcast the your wireless network name (SSID), making it easier for wireless clients to find the wireless network.

© Copyright 2012 TRENDnet. All Rights Reserved. 20 TRENDnet User’s Guide TEW-715APO Router Mode Below describes the configuration settings when the TEW-715APO System Mode is set to Router. In this configuration the Ethernet port of the TEW-715APO can serve as the WAN (Wide Area Network) or Internet port. Please verify your network configuration when using this mode. Please refer to Internet Service Types section in the Appendix to help determine your Internet settings. Configuration 1. Log into the management page (see “Access the management page” on page 9). 2. Your access point will prompt you for a user name and password. 3. Enter the default user name and password and then click Login. Default User Name: admin Default Password: admin 4. Click the System button on the left side and then System Settings. 5. Select Router in the System Mode drop down menu. 6. Click Apply button to save your setting. 7. Click the Wireless button on the left side and then Basic Settings. 8. Select the mode you would like to apply Operation Mode pull down menu. Click Apply to save changes. • AP Mode: Creates a wireless network with your device (similar to a wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. • Wireless Client: Connects to any existing wireless network (similar to a wireless adapter) in which the wireless network the device is connecting to serves as your Internet connection. Ethernet port serves as a LAN (Local Area Network) port of the device and the wireless settings is based on your ISP (Internet Service Provider) connection. • Bridge: Creates a wireless network with your device (similar to a wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. • AP Repeater: Creates a wireless network with your device (similar to a wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port.

© Copyright 2012 TRENDnet. All Rights Reserved. 21 TRENDnet User’s Guide TEW-715APO AP Mode Wireless > Basic When AP mode is selected a wireless network is created with your device (similar to w wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. This section outlines available management options when the device System Setting is set to Router and the wireless Operation Mode is set to AP. Click Apply to save any changes. • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional information to operate the device as an access point. • Wireless Network Name (SSID): This acronym stands for Service Set Identifier and is the name of your wireless network. It differentiates your wireless network from others around you. By default, the access point broadcast TRENDnet715 as

© Copyright 2012 TRENDnet. All Rights Reserved. 22 TRENDnet User’s Guide TEW-715APO the wireless network name. If you choose to change the SSID, change it to a name that you can easily remember. You can click more to configure additional SSID. Please refer to pagexxxx • Broadcast SSID: o Enable: Access point will broadcast the your wireless network name (SSID), making it easier for wireless clients to find the wireless network. o Disable: Access point will not broadcast the wireless network name (SSID) and wireless clients will have to manually enter the wireless network to connect. • 802.11 Mode: If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate mode. If you have some devices that use a different transmission mode, choose the appropriate mode. o 802.11b/g mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will allow both wireless b and wireless g client to connect and access point, at 54Mbps for wireless g and share access at the same time. Although the wireless b/g operates in the 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. o 802.11b/g/n mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will only allow the use of wireless g client devices to connect and access point, 54Mbps for wireless g and up to 300Mbps* for wireless n and share access at the same time. Although the wireless b/g/n operates in the same 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless b/g/n) to connect and access at the same time. • HT protect: Enable HT (High Throughput) protect to ensure HT transmission with MAC mechanism. Under 802.11n mode, wireless client can be divided into HT STA and Non-HT STA, among which the one with HT protect enabled gets higher throughput. • Frequency (Channel): To manually set the channel on which the router will broadcast, uncheck Auto Channel, then click the drop-down list and select the desired Channel for wireless communication. The goal is to select the Channel that is least used by neighboring wireless networks. • Extension channel: When 20/40 channel bandwidth has been chosen, you should select extension channel to get higher throughput. • Channel Mode: Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more bandwidth, thus it might cause potential interference. • Antenna: By default, IEEE 802.11b/g/n Wireless CPE uses its built-in antenna for directional transmission; however, if you prefer to use an external antenna for your case-dependent applications, you can switch from “Internal (8 dBi)” to” External (N-Type)”. When External (N-Type) is selected, an Antenna Gain bar will appear to allow you specify the gain of the external antenna. The antenna gain calculates the TX power back off needed to remain in compliance with regulations. Please refer to External Antenna installation on page 49. o You are able to choose “External (N-Type)” only when you have well done installing the external antenna; otherwise, it might damage IEEE 802.11b/g/n Wireless CPE itself. o The maximum output power will vary depending on the country selected in order to comply with the local regulation. o The output power here is counted from the RF single chain only not including the 8dBi internal antenna. • Maximum Output power: Specify the signal transmission power. The higher the output power is, the wider the signal can cover, but the power consumption will be greater accordingly. • Data Rate: Usually “Auto” is preferred. Under this rate, the IEEE 802.11b/g/n Wireless CPE will automatically select the highest available rate to transmit. In some cases, however, like where there is no great demand for speed, you can have a relatively-low transmit rate for compromise of a long distance. • Extension Channel Protection: This is to avoid conflict with other wireless network and boost the ability of your device to catch all 802.11g transmissions. However, it may decrease wireless network performance. Compared to CTS-Self; the transmission amount of CTS-RTS is much lower.

© Copyright 2012 TRENDnet. All Rights Reserved. 24 TRENDnet User’s Guide TEW-715APO • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional informationto operate the device as an access point. • Site Survey: Click to scan and select available wireless networks. • Wireless Network Name (SSID): This acronym stands for Service Set Identifier and is the name of your wireless network. You can manually enter the wireless network you want to connect to or click “Site Survey” option to scan for available wireless networks around you. Please refer to pagexxx • Lock AP MAC: Enter the MAC address of the access point you are connected. • 802.11 Mode: If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate mode. If you have some devices that use a different transmission mode, choose the appropriate mode. o 802.11b/g mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will allow both wireless b and wireless g client to connect and access point, at 54Mbps for wireless g and share access at the same time. Although the wireless b/g operates in the 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. o 802.11b/g/n mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will only allow the use of wireless g client devices to connect and access point, 54Mbps for wireless g and up to 300Mbps* for wireless n and share access at the same time. Although the wireless b/g/n operates in the same 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless b/g/n) to connect and access at the same time. • Channel Mode: Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more bandwidth, thus it might cause potential interference. • Antenna: By default, IEEE 802.11b/g/n Wireless CPE uses its built-in antenna for directional transmission; however, if you prefer to use an external antenna for your case-dependent applications, you can switch from “Internal (8 dBi)” to” External (N-Type)”. When External (N-Type) is selected, an Antenna Gain bar will appear to allow you specify the gain of the external antenna. The antenna gain calculates the TX power back off needed to remain in compliance with regulations. Please refer to External Antenna installation on page 49. o You are able to choose “External (N-Type)” only when you have well done installing the external antenna; otherwise, it might damage IEEE 802.11b/g/n Wireless CPE itself. o The maximum output power will vary depending on the country selected in order to comply with the local regulation. o The output power here is counted from the RF single chain only not including the 8dBi internal antenna. • Maximum Output power: Specify the signal transmission power. The higher the output power is, the wider the signal can cover, but the power consumption will be greater accordingly. • Data Rate: Usually “Auto” is preferred. Under this rate, the IEEE 802.11b/g/n Wireless CPE will automatically select the highest available rate to transmit. In

© Copyright 2012 TRENDnet. All Rights Reserved. 26 TRENDnet User’s Guide TEW-715APO Bridge Mode Wireless > Basic When Bridge is selected a wireless network is created with your device (similar to a wireless router). Device Ethernet port serves as a WAN (Wide Area Network) or Internet port. This section outlines available management options under the Basic Settings of the Wireless button when the Operation Mode is set to Bridge and will assist in setting up the access point. Click Apply to save any changes. • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional information to operate the device as an access point. • 802.11 Mode: If all of the wireless devices you want to connect with this Access Point can connect in the same transmission mode, you can improve performance slightly by choosing the appropriate mode. If you have some devices that use a different transmission mode, choose the appropriate mode. o 802.11b/g mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will allow both wireless b and wireless g client to

© Copyright 2012 TRENDnet. All Rights Reserved. 27 TRENDnet User’s Guide TEW-715APO connect and access point, at 54Mbps for wireless g and share access at the same time. Although the wireless b/g operates in the 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless n/g @ 54Mbps) to connect and access at the same time. o 802.11b/g/n mixed mode (2.4GHz) - This wireless mode works in the 2.4GHz frequency range and will only allow the use of wireless g client devices to connect and access point, 54Mbps for wireless g and up to 300Mbps* for wireless n and share access at the same time. Although the wireless b/g/n operates in the same 2.4GHz frequency, it will allow the use of other 2.4GHz client devices (Wireless b/g/n) to connect and access at the same time. • Frequency (Channel): To manually set the channel on which the router will broadcast, uncheck Auto Channel, then click the drop-down list and select the desired Channel for wireless communication. The goal is to select the Channel that is least used by neighboring wireless networks. • Extension channel: When 20/40 channel bandwidth has been chosen, you should select extension channel to get higher throughput. • Channel Mode: Four levels are available: 5MHz, 10MHz, 20MHz and 40MHz. The last one can enhance data throughput, but it takes more bandwidth, thus it might cause potential interference. • Antenna: By default, IEEE 802.11b/g/n Wireless CPE uses its built-in antenna for directional transmission; however, if you prefer to use an external antenna for your case-dependent applications, you can switch from “Internal (8 dBi)” to” External (N-Type)”. When External (N-Type) is selected, an Antenna Gain bar will appear to allow you specify the gain of the external antenna. The antenna gain calculates the TX power back off needed to remain in compliance with regulations. Please refer to External Antenna installation on page 49. o You are able to choose “External (N-Type)” only when you have well done installing the external antenna; otherwise, it might damage IEEE 802.11b/g/n Wireless CPE itself. o The maximum output power will vary depending on the country selected in order to comply with the local regulation. o The output power here is counted from the RF single chain only not including the 8dBi internal antenna. • Maximum Output power: Specify the signal transmission power. The higher the output power is, the wider the signal can cover, but the power consumption will be greater accordingly. • Data Rate: Usually “Auto” is preferred. Under this rate, the IEEE 802.11b/g/n Wireless CPE will automatically select the highest available rate to transmit. In some cases, however, like where there is no great demand for speed, you can have a relatively-low transmit rate for compromise of a long distance. • Extension Channel Protection: This is to avoid conflict with other wireless network and boost the ability of your device to catch all 802.11g transmissions. However, it may decrease wireless network performance. Compared to CTS-Self; the transmission amount of CTS-RTS is much lower. Wireless >WDS Setting This section outlines the available management options under the WDS Settings of the Wireless button. Note: WDS Settings is available only under Bridge and AP Repeater Mode. • WDS Separation: Enable separates all configured WDS AP to communicate with each other. • Remote AP: Enter the MAC address of the access point you want to WDS with. Note: You must enter the MAC address of every access point in the WDS network. Each wireless setting (SSID, channel, wireless encryption) must match on each access point in the WDS network.

© Copyright 2012 TRENDnet. All Rights Reserved. 28 TRENDnet User’s Guide TEW-715APO AP Repeater Mode Wireless > Basic When Router mode is applied as the system mode and the operation mode is set to AP Repeater, the access point serves as a wireless router. This section outlines available management options under the Basic Settings of the Wireless button when the Operation Mode is set to Bridge and will assist in setting up the access point. Click Apply to save any changes. • Disable Wireless LAN Interface: o Check/Off: turns off wireless networking on your router. o Unchecked/On: turns on the wireless networking on your router (by default it is enabled). Note: It is recommended to leave the wireless setting to On unless you do not plan on connecting any wireless computers or devices to your network. • Operation Mode: Select the mode you want the access point to operate in. o AP: refer to pagexxxx for additional information. o Wireless Client: refer to page xxx for additional information o Bridge: refer to page xxx for additional information o AP Repeater: refer to page xxx for additional information to operate the device as an access point. • Wireless Network Name (SSID): This acronym stands for Service Set Identifier and is the name of your wireless network. You can manually enter the wireless network you want to repeat. • Broadcast SSID: o Enable: Access point will broadcast the your wireless network name (SSID), making it easier for wireless clients to find the wireless network.

© Copyright 2012 TRENDnet. All Rights Reserved. 30 TRENDnet User’s Guide TEW-715APO Wireless Networking and Security How to choose the type of security for your wireless network Setting up wireless security is very important. Leaving your wireless network open and unsecure could expose your entire network and personal files to outsiders. TRENDnet recommends reading through this entire section and setting up wireless security on your new router. There are a few different wireless security types supported in wireless networking each having its own characteristics which may be more suitable for your wireless network taking into consideration compatibility, performance, as well as the security strength along with using older wireless networking hardware (also called legacy hardware). It is strongly recommended to enable wireless security to prevent unwanted users from accessing your network and network resources (personal documents, media, etc.). In general, it is recommended that you choose the security type with the highest strength and performance supported by the wireless computers and devices in your network. Please review the security types to determine which one you should use for your network. Wireless Encryption Types • WEP: Legacy encryption method supported by older 802.11b/g hardware. This is the oldest and least secure type of wireless encryption. It is generally not recommended to use this encryption standard, however if you have old 802.11 b or 802.11g wireless adapters or computers with old embedded wireless cards(wireless clients), you may have to set your router to WEP to allow the old adapters to connect to the router. Note: This encryption standard will limit connection speeds to 54Mbps. • WPA: This encryption is significantly more robust than the WEP technology. Much of the older 802.11g hardware was been upgraded (with firmware/driver upgrades) to support this encryption standard. Total wireless speeds under this encryption type however are limited to 54Mbps. • WPA-Auto: This setting provides the router with the ability to detect wireless devices using either WPA or WPA2 encryption. Your wireless network will automatically change the encryption setting based on the first wireless device connected. For example, if the first wireless client that connects to your wireless network uses WPA encryption your wireless network will use WPA encryption. Only when all wireless clients disconnect to the network and a wireless client with WPA2 encryption connects your wireless network will then change to WPA2 encryption. NOTE: WPA2 encryption supports 802.11n speeds and WPA encryption will limit your connection speeds to 54Mbps • WPA2: This is the most secure wireless encryption available today, similar to WPA encryption but more robust. This encryption standard also supports the highest connection speeds. TRENDnet recommends setting your router to this encryption standard. If you find that one of your wireless network devices does not support WPA2 encryption, then set your router to either WPA or WPA-Auto encryption. Note: Check the specifications of your wireless network adapters and wireless appliances to verify the highest level of encryption supported. Below is brief comparison chart of the wireless security types and the recommended configuration depending on which type you choose for your wireless network. Security Standard WEP WPA WPA2 Compatible Wireless Standards IEEE 802.11a/b/g (802.11n devices will operate at 802.11g to connect using this standard) IEEE 802.11a/b/g (802.11n devices will operate at 802.11g to connect using this standard) IEEE 802.11a/b/g/n Highest Performance Under This Setting Up to 54Mbps Up to 54Mbps Up to 450Mbps* Encryption Strength Low Medium High Additional Options Open System or Shared Key, HEX or ASCII, Different key sizes TKIP or AES, Preshared Key or RADIUS TKIP or AES, Preshared Key or RADIUS Recommended Configuration Open System ASCII 13 characters TKIP Preshared Key AES Preshared Key

© Copyright 2012 TRENDnet. All Rights Reserved. 32 TRENDnet User’s Guide TEW-715APO o This is where you enter the password or key needed for a computer to connect to the router wirelessly o You can define up to 4 passwords or 4 keys. Only one key can be active at a given time. Most users simply define one key. o Choose a key index 1, 2, 3, or 4 and enter the key. o When connecting to the router, the client must match both the password and the Key number. (e.g. if you have activated Key 2 with a password of 12345, then the client must select: Key 2 (entering Key 1, 3, or 4 will block the ability to connect) and enter password 12345) • WEP Passphrase: Enter a passphrase and click Generate key to have the access point generate your encryption key. Selecting WPA-PSK, WPA2-PSK, or WPA-PSK & WPA2-PSK (WPA2-PSK recommended): The following section outlines options when selecting PSK (Preshared Key Protocol). • Data Encryption: Select the cipher type to use. o TKIP: Recommended when using WPA-PSK security. o AES: Recommended when using WPA2-PSK or WPA-PSK & WPA2-PSK • WPA Passphrase – Enter the passphrase. o This is the password or key that is used to connect your computer to this router wirelessly Selecting WPA, WPA2, or WPA & WPA2 with Radius: The following section outlines options when selecting Radius. Note: Radius requires an external RADIUS server, PSK only requires you to create a passphrase. • Data Encryption: Select the cipher type to use. o TKIP: Recommended when using WPA-PSK security. o AES: Recommended when using WPA2-PSK or WPA-PSK & WPA2-PSK Once you have selected the data encryption type. Click Apply to save settings and go to the RADIUS Settings section under System button on the left side. The following section outlines options to configure the access point’s RADIUS settings. • Radius Server - Configure the RADIUS server settings. o IP – Enter the IP address of the RADIUS server. (e.g. 192.168.10.250) o Port – Enter the port your RADIUS server is configured to use for RADIUS authentication. Note: It is recommended to use port 1812. WEP Key Format HEX ASCII Character set 0-9 & A-F, a-f only Alphanumeric (a,b,C,?,*, /,1,2, etc.) 64-bit key length 10 characters 5 characters 128-bit key length 26 characters 13 characters

© Copyright 2012 TRENDnet. All Rights Reserved. 33 TRENDnet User’s Guide TEW-715APO o Shared Secret – Enter the shared secret used to authorize your router • Global-Key Update o Enable this option to set the cache period based on seconds Wireless access control Wireless > Access Control The MAC address filter section can be used to filter network access by machines based on the unique MAC addresses of their network adapter(s). It is most useful to prevent unauthorized wireless devices from connecting to your network. A MAC address is a unique ID assigned by the manufacturer of the network adapter. • Access Control Mode: o Disable: Access control is disabled o Allow Listed: Enter MAC address allowed to connect to the access point o Deny List: Enter MAC addresses to block connection to the access point. Advance Settings Change your IP address Basic Setting > Primary Setup In most cases, you do not need to change the access point’s IP address settings. Typically, the access point IP address settings only needs to be changed, if you plan to use another access point in your network with the same IP address settings, if you are connecting the access point to an existing network that is already using the IP address settings your access point is using. In addition, the access point can be used as a DHCP (Dynamic Host Configuration Protocol) server to automatically assign an IP address to each computer or device on your network. If you already have a DHCP server on your network, or if you do not want to use the access point as a DHCP server, you can disable this setting. This setting would be used when the access point’s System settings is set to Router mode. Note: If you are not encountering any issues or are not faced with one of the cases described above or similar, it is recommended to keep your router IP address settings as default. Note: For VPN (Virtual Private Network) configuration, it is required that each router should have a different router or LAN IP address/network on each end of the VPN tunnel. Default Router or LAN IP Address: 192.168.10.1 00 Default Router or LAN IP Network: 192.168.10.0 / 255.255.255.0 1. Log into the management page (see “Access the management page” on page 9). 2. Click on System, and click on Network Settings.

© Copyright 2012 TRENDnet. All Rights Reserved. 34 TRENDnet User’s Guide TEW-715APO • IP Address: Enter the new access point IP address. (e.g. 192.168.100.1) • Subnet Mask: Enter the new access point subnet mask.(e.g. 255.255.255.0) • DHCP Server: Enable or Disable the DHCP server on the access point. • DHCP IP Address Range: Enter the IP address of the DHCP server to assign. • Lease Time: Enter the lease time in seconds that DHCP client will hold their automatically assigned IP address before requesting a new IP address • Enable DHCP Relay: Enable to forward DHCP requests and replies between clients and servers when they are not on the same physical subnet • DHCP Server IP: Enter the DHCP IP address of the DHCP Relay Note: The DHCP address range will change automatically to your new access point’s IP address settings so you do not have to change the DHCP address range manually to match your new router IP address settings. 3. To save changes, click Apply at the bottom of the page. Note: If you changed the IP address of the access point you will need to access the management page using the new IP address (e.g Instead of using the default http://192.168.10.100 using your new router IP address will use the following format using your new router IP address http://(new.router.ipaddress.here) to access the management page. Configure your Internet connection System > Network Settings This section describes the features when setting the access points WAN settings. The access point supports DHCP, Static or PPPoE WAN types. Refer to Internet Service Type section in the Appendix for additional information on connection types. Before configuring this section, complete the settings in the Router Mode section to determine the type of networking you will be setting. Note: This feature is only available when Router mode is applied in System Settings. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on System, and click on Network Settings. 3. In the WAN Access Type drop-down list, select the type of Internet connection provided by your ISP (Internet Service Provider). 4. Complete the fields required by your ISP. 5. Complete the optional settings only if required by your ISP. 6. To save changes, click Save. Note: If you are unsure which Internet connection type you are using, please contact your ISP (Internet Service Provider).

© Copyright 2012 TRENDnet. All Rights Reserved. 35 TRENDnet User’s Guide TEW-715APO Setting time System > Time Settings 1. Log into the management page (see “Access the management page” on page 9). 2. Click on System, and click on Time Settings. Manual configure time settings 1. Manually enter the date and time settings. 2. Next to Time Zone Select, select your time zone from the drop down menu. Click Apply to save settings. Time setting using a NTP server 1. Click Enable NTP client update option to obtain date and time settings from a NTP server. 2. Select one of the below options. Click Apply to save settings. • NTP Server: Select a NTP server to use. • Manual IP: Manually enter your NTP server. 2. You can also click Enable NTP client update option to obtain date and time settings from a NTP server. Advance wireless settings Wireless > Advance Settings This section outlines available management options under the Advance Settings of the Wireless button. • A-MPDU/A-MSDU aggregation: The data rate of your AP except wireless client mode could be enhanced greatly with this option enabled; however, if your wireless clients don’t support A-MPDU/A-MSDU aggregation, it is not recommended to enable it. • Short GI: Under 802.11n mode, enable it to obtain better data rate if there is no negative compatibility issue. • RTS Threshold: The IEEE 802.11b/g/n Wireless CPE sends RTS (Request to Send) frames to certain receiving station and negotiates the sending of a data frame. After receiving an RTS, that STA responds with a CTS (Clear to Send) frame to acknowledge the right to start transmission. The setting range is 0 to 2346 in byte. Setting it too low may result in poor network performance. Leave it at its default of 2346 is recommended.

© Copyright 2012 TRENDnet. All Rights Reserved. 36 TRENDnet User’s Guide TEW-715APO • Fragment Threshold: Specify the maximum size in byte for a packet before data is fragmented into multiple packets. Setting it too low may result in poor network performance. Leave it at its default of 2346 is recommended. • Beacon Interval: Specify the frequency interval to broadcast packets. Enter a value between 20 and 1024. • DTIM Interval: DTIM, which stands for Delivery Traffic Indication Message, is contained in the data packets. It is for enhancing the wireless transmission efficiency. The default is set to 1. Enter a value between 1 and 255. • Preamble Type: It defines some details on the 802.11 physical layer. “Long” and “Auto” are available. • IGMP Snooping: Available in AP/Router mode, IGMP snooping is the process of listening to IGMP network traffic. By enabling IGMP snooping, the AP will listen to IGMP membership reports, queries and leave messages to identify the ports that are members of multicast groups. Multicast traffic will only be forwarded to ports identified as members of the specific multicast group or groups. • RIFS: RIFS (Reduced Interframe Spacing) is a means of reducing overhead and thereby increasing network efficiency. • Link Integration: Available under AP/Bridge/AP repeater mode, it monitors the connection on the Ethernet port by checking “Enabled”. It can inform the associating wireless clients as soon as the disconnection occurs. • TDM Coordination: Stands for “Time-Division Multiplexing Technique”, this resource reservation control mechanisms can avoid packet collisions and send the packets much more efficiently allowing for higher effective throughput rates. This function is only available in AP/CPE mode. It is highly recommended to enable TDM coordination when there are multiple CPEs needed to connect to the AP in your application. • Space in Meter: To decrease the chances of data retransmission at long distance, the IEEE 802.11b/g/n Wireless CPE can automatically adjust proper ACK timeout value by specifying distance of the two nodes. • Traffic Shaping: Allows the administrator to specify the incoming and outgoing traffic limit by checking “Enable Traffic Shaping”. This is only available in Router mode. You can set the multiple SSID to a specific VLAN. • Enable: Select this option to enable 802.1Q VLAN on the enabled multiple SSID. • Management VLAN: Enter the VLAN ID to set on your network. Change your login password Basic Setting > Change Password 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Password Settings. Click Apply to save changes. • Current Password: Enter the current password of the access point. • New Password: Enter the new password • Confirm Password: Re-enter the new password to confirm. Note: If you change the login password, you will need to access the management page using the new password instead of the default password “admin”.

© Copyright 2012 TRENDnet. All Rights Reserved. 37 TRENDnet User’s Guide TEW-715APO Access Control Source IP Filtering Firewall Setting > Src IP Filtering The Source IP Filtering gives users the ability to restrict certain types of data packets from your local network to the access point. Use of such filters can be helpful in securing or restricting your local network. Please note that this feature is only available when access point System Mode is set to Router. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Firewall Settings, and click on Src IP Filtering. Click Apply to save settings. • Enable Source IP Filtering: Check this option to enable source IP filtering • Local IP Address: Enter the IP address you would like to apply the IP filtering rule. • Comment: Enter any notes you would like to add to distinguish the rule. Destination IP Filtering Firewall Setting > Dst IP Filtering The destination IP filtering gives you the ability to restrict the computers in LAN from accessing certain websites in WAN according to specified IP addresses. Please note that this feature is only available when access point System Mode is set to Router. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Firewall Settings, and click on Dst IP Filtering. Click Apply to save settings. • Enable Destination IP Filtering: Check this option to enable source IP filtering • Destination IP Address: Enter the IP address you would like to apply the destinationIP filtering rule. • Comment: Enter any notes you would like to add to distinguish the rule. Source Port Filtering Firewall Setting > Src Port Filtering The source port filtering enable you to restrict certain ports of data packets from your local network to Internet through the access point. Use of such filters can be helpful in securing or restricting your local network. Please note that this feature is only available when access point System Mode is set to Router. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Firewall Settings, and click on Src Port Filtering. Click Apply to save settings. • Enable Destination IP Filtering: Check this option to enable source IP filtering • Port Range: Enter the range of ports you would like to apply the source port filtering. • Protocol: Select the protocol you would like to filter. From UDP, TCP or Both (UDP and TCP). • Comment: Enter any notes you would like to add to distinguish the rule.

© Copyright 2012 TRENDnet. All Rights Reserved. 38 TRENDnet User’s Guide TEW-715APO Destination Port Filtering Firewall Setting > Dst Port Filtering The destination port filtering enables you to restrict certain ports of data packets from your local network to Internet through the access point. Use of such filters can be helpful in securing or restricting your local network. Please note that this feature is only available when access point System Mode is set to Router. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Firewall Settings, and click on Dst Port Filtering. Click Apply to save settings. • Enable Destination IP Filtering: Check this option to enable source IP filtering • Port Range: Enter the range of ports you would like to apply the source port filtering. • Protocol: Select the protocol you would like to filter. From UDP, TCP or Both (UDP and TCP). • Comment: Enter any notes you would like to add to distinguish the rule. Port Fordwarding Firewall Setting > Port Forwarding The destination port filtering enables you to restrict certain ports of data packets from your local network to Internet through the access point. Use of such filters can be helpful in securing or restricting your local network. Please note that this feature is only available when access point System Mode is set to Router. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Firewall Settings, and click on Port Forwarding. Click Apply to save settings. • Enable Destination IP Filtering: Check this option to enable source IP filtering • IP Address: Enter the IP address of the device to forward the port. (e.g. 192.168.10.101). • Protocol: Select the protocol required for your device. TCP, UDP, or you can select Both to choose both TCP & UDP. • Port Range: Enter the port number used to access the device from the Internet. • Comment: Enter any notes you would like to add to distinguish the rule. Example: To forward TCP port 80 to your network/IP camera 1. Make sure to configure your network/IP camera to use a static IP address or you can use the DHCP reservation feature (see “Set up DHCP reservation” on page 55). Note: You may need to reference your camera documentation on configuring a static IP address. 2. Log into the management page (see “Access the management page” on page 9). 3. Click on Firewall Settings on the side, click on Port Forwarding. 4. Under IP Address, enter the IP address assigned to the camera. (e.g. 192.168.10.101) 5. To save changes, click Save at the bottom of the page.

© Copyright 2012 TRENDnet. All Rights Reserved. 39 TRENDnet User’s Guide TEW-715APO Open a device on your network to the Internet DMZ Firewall Settings > DMZ Setting You may want to expose a specific computer or device on your network to the Internet to allow anyone to access it. Your router includes the DMZ (demilitarized zone) feature that makes all the ports and services available on the WAN/Internet side of the router and forwards them to a single IP address (computer or network device) on your network. The DMZ feature is an easy way of allowing access from the Internet however, it is also very insecure method. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Firewall Settings, and click on DMZ Setting. Click Apply to save settings. • Enable DMZ: Check this option to enable DMZ • DMZ Host IP Address: Enter the IP address you would like to apply DMZ. UDP Pass through Firewall Settings > UDP Pass through You may want to expose a specific computer or device on your network to the Internet to allow anyone to access it. Your router includes the DMZ (demilitarized zone) feature that makes all the ports and services available on the WAN/Internet side of the router and forwards them to a single IP address (computer or network device) on your network. The DMZ feature is an easy way of allowing access from the Internet however, it is also very insecure method. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Firewall Settings, and click on UDP Pass through. Click Apply to save settings. • Enable UDP Pass through: Check this option to enable UDP Pass through Configure your log Tool Settings > System Log You may want send your router log to your e-mail address or to an external log server (also known as Syslog server) so you can check it periodically while away from home. You may also want to only see specific categories of logging. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Tools, and click on System Log. Click Apply to save settings. • Enable Remote Syslog Server: Check this option to enable DMZ • IP Address: enter the IP address (e.g. 192.168.10.250) of the external log server to send • Port: Enter the port used on your log server. View your log Tool Settings > System Log

© Copyright 2012 TRENDnet. All Rights Reserved. 40 TRENDnet User’s Guide TEW-715APO You may want send your router log to your e-mail address or to an external log server (also known as Syslog server) so you can check it periodically while away from home. You may also want to only see specific categories of logging. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Tools, and click on System Log. Click Apply to save settings. • Time: Displays the date and time of the log entry. If the time is inaccurate, make sure to set the router date and time correctly. (See “Setting time” on page 51) • Source: Source of the log entry • Message: Displays the log message. • Refresh: Click to refresh the displayed log entries • Clear: Click to clear all current log entries Ping Watchdog Ping Watchdog Tools > Ping Watchdog You may want to expose a specific computer or device on your network to the Internet to allow anyone to access it. Your router includes the DMZ (demilitarized zone) feature that makes all the ports and services available on the WAN/Internet side of the router and forwards them to a single IP address (computer or network device) on your network. The DMZ feature is an easy way of allowing access from the Internet however, it is also very insecure method. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Tools, and click on Ping Watchdog. Click Apply to save settings. • Enable Ping Watchdog: Check this option to enable option • IP Address to Ping: Enter the IP address of the remote unit to ping • Ping Interval: Enter the time interval in seconds to ping the remote unit • Startup Delay: Enter the startup delay time in seconds to prevent the reboot before the access point is initialized • Failure Count To Reboot: Enter the count value of when the access point will reboot automatically WDS Data Rate Test Tool > Date Rate Test For troubleshooting purposes, you may want to check your WDS connectivity using the data rate test tool on your router management page. Please note that this option is only available when Bridge Mode is selected. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Tools, and click on Data Rate Test.

© Copyright 2012 TRENDnet. All Rights Reserved. 41 TRENDnet User’s Guide TEW-715APO 3. Select the WDS Node you would like to test. 4. Click Start to begin test and Stop to end test. If you cannot find your remote device click Refresh. Antenna Alignment Tool > Antenna Alignment Under Bridge mode, when the bridges are not easily visible from the location where the dish will be installed, the antenna alignment tool can help you evaluate the position of the unit and adjust the angle of the antenna more precisely. Keep it in mind that additional factors should be taken into account when your unit is installed. These factors include various obstacles (buildings, trees), the landscape, the altitude, transponder orientation, polarization, etc. To use the tool, select the desired remote access point and click “Start”, the web page will display the measured signal strength, RSSI and transmit/receive packets. If the signal quality is not quite good, try to adjust the antenna and see if the quality improves or not. Please note that this option is only available when Bridge mode is enabled. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Tools, and click on Antenna Alignment. 3. Select the remote access point you are configuring. 4. Click Start to begin test. If you cannot find your remote device click Refresh. Speed Test Tool > Speed Test The speed test is to monitor the current data transmission (TX) and data reception (RX) rate with the remote access point. Enter the IP address of the remote access point, type in the user name/password and click “Test”. The result will display in the bottom STATUS. You may test single TX/RX or bi-direction. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Tools, and click on Speed Test. • Destination IP: Enter the IP address of the remote access point • Username: Enter the username of the remote access point • Password: Enter the password information for the remote access point • Direction: Select the direction you would like to test with the remote access point. Remote Mangement Management > Remote Management The access point provides a variety of remotes managements tools including Telnet, SNMP, FTP, SSH, HTTPS and exclusive WISE tool, making configuration more convenient and secure. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Remote Management.

© Copyright 2012 TRENDnet. All Rights Reserved. 43 TRENDnet User’s Guide TEW-715APO Coovachili Management > Coovachili Settings Coovachilli is a captive portal management which allows WLAN users to easily and securely access the Internet. Under Router mode, when Coovachilli is enabled, the IEEE 802.11b/g/n Wireless Access Point will force an HTTP client on a network to see a special web page (usually for authentication purposes) before using the Internet normally. At that time the browser is redirected to a web page which may require authentication. Captive portals are used at most Wi-Fi hotspots. Therefore, to use Coovachilli, you need to find Coovachilli service providers that have the additional services needed to make Coovahcilli work. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on CoovaChili Settings. 3. Select Coovachilli Enable to turn on feature. 4. Configure the settings below and click Apply to save settings. Radius Settings • Primary Radius Server: Enter the name or IP address of the primary radius server • Secondary Radius Server: Enter the name or IP address of the primary radius server if any. • Radius Auth Port: Enter the port number for authentication • Radius Acct Port: Enter the port number for billing • Radius Shared Secret: Enter the secret key of the radius server • Radius NAS ID: Enter the name of the radius server if any Radius Administrative-User • Radius Admin Username: Enter the username of the Radius Administrator • Radius Admin Password: Enter the password of the Radius Administrator Captive Portal • UAM Portal URL: Enter the address of the UAM portal server • UAM Secret: Enter the secret password between the redirect URL and the Hotspot. Upgrade Firmwre Management > Firmware Upload You may have added many customized settings to your router and in the case that you need to reset your router to default, all your customized settings would be lost and would require you to manually reconfigure all of your router settings instead of simply restoring from a backed up router configuration file. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Firmware Upload.

© Copyright 2012 TRENDnet. All Rights Reserved. 44 TRENDnet User’s Guide TEW-715APO 3. Click Browse and select the updated firmware file you want to load. Click Upload to load the firmware file. Note: Any interruption during the firmware upgrade can damage your device. Backup and restore your router configuration settings You may have added many customized settings to your router and in the case that you need to reset your router to default, all your customized settings would be lost and would require you to manually reconfigure all of your router settings instead of simply restoring from a backed up router configuration file. To back up your configuration: Management > Configuration File 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Configuration File. 3. Depending on your web browser settings, you may be prompted to save a file (specify the location) or the file may be downloaded automatically to the web browser settings default download folder. (Default Filename: config.bin) 4. Save the configuration file to location on your computer. To restore your router configuration and upgrade firmware Management > Configuration File 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Configuration File. 3. Under Load Settings from file, click on Browse select your saved configuration file and click Upload. Reboot your access point Management > Configuration File You may want to restart your router if you are encountering difficulties with your router and have attempted all other troubleshooting. There are two methods that can be used to restart your router. • Disconnect the power adapter – Located on the rear panel of your router, see “Product Hardware Features” on page 4 . Use this method if you are encountering difficulties with accessing your router management page. This is also known as a hard reboot or power cycle. Disconnect the power adapter from the power port of your router for 10 seconds, then, plug the power adapter back into the power of your router. Wait for your router Status light to begin flashing. OR • Router Management Page – This is also known as a soft reboot or restart. Toolbox > Reboot 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Configuration File. 3. Click Yes or OK if prompted to your reboot your device.

© Copyright 2012 TRENDnet. All Rights Reserved. 45 TRENDnet User’s Guide TEW-715APO Reset to factory defaults You may want to reset your router to factory defaults if you are encountering difficulties with your router and have attempted all other troubleshooting. Before you reset your router to defaults, if possible, you should backup your router configuration first, see “Backup and restore your router configuration settings” on page 70. There are two methods that can be used to reset your router to factory defaults. • Reset Button – Located on the bottom panel of the access point, cap must be removed to access reset button. Use this method if you are encountering difficulties with accessing your router management page. Push and hold this button for 15 seconds and release to reset your router to its factory defaults. Bottom cap remove OR • Router Management Page Management > Configuration Filet 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Configuration File. 3. You will be prompted to reset your router to factory defaults. Click Yes or OK. Certificate configuration settings Management > Certificate Settings Under Client mode, when EAP-TLS is used, the RADIUS server must know which user certificates to trust. The Server can trust all certificates issued by a given CA. To import a user certificate, from Import User Certificates, click “Browse” and specify the location where the user certificate is placed. Click “Import”. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Management, and click on Certificate Settings. • Delete User Certificate: Select from the pull down menu the certificate would like to delete and deactivate. Press Delete to proceed. • Import User Certificate: Click Browse and select the user certificate you want to load to the access point. Click Import to load the certificate. Device Information Status > Information Under Client mode, when EAP-TLS is used, the RADIUS server must know which user certificates to trust. The Server can trust all certificates issued by a given CA. To import a user certificate, from Import User Certificates, click “Browse” and specify the location where the user certificate is placed. Click “Import”. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Status, and click on Information.

© Copyright 2012 TRENDnet. All Rights Reserved. 46 TRENDnet User’s Guide TEW-715APO System Information • Device Name: Name of device • Country/Region: Applied country/region • Firmware Version: Current firmware version of the access point. WAN Settings Information is based on the mode settings applied to the access point and when System mode is to Router. • Connection Time: Display time duration of when the WAN has established connection • Access Type: Display the WAN connection type • IP Address: Current assigned WAN IP address • Subnet Mask: Assigned WAN Subnet Mask • Default Gateway: Assigned WAN default gateway • DNS1/2: Assigned WAN DNS IP address • MAC Address: Displays the MAC address of the access points WAN port LAN Settings Information is based on the Wireless mode setting applied to the access pointr. • IP Address: LAN IP address of your access point • Subnet Mask: Subnet Mask of your Local Area Network (LAN) • MAC Address: Displays the MAC address of your access points Local Area Network (LAN) • Connection Time: Display time duration of when the WAN has established connection • Access Type: Display the WAN connection type • IP Address: Current assigned WAN IP address • Subnet Mask: Assigned WAN Subnet Mask • Default Gateway: Assigned WAN default gateway • DNS1/2: Assigned WAN DNS IP address MAC Address: • elect from the pull down menu the certificate would like to delete and deactivate. Press Delete to proceed. Associated Information Status > Connections Open “Connections” in “Status” to check the information of associated wireless devices such as MAC address, signal strength, connection time, IP address, etc. All is read only. Click “Refresh” at the bottom to update the current association list. By clicking on the MAC address of the selected device on the web you may see more details including device name, connection time, signal strength, noise floor, ACK timeout, link quality, IP information, current data rate, current TX/RX packets.

© Copyright 2012 TRENDnet. All Rights Reserved. 47 TRENDnet User’s Guide TEW-715APO 1. Log into the management page (see “Access the management page” on page 27). 2. Click on Status, and click on Connections. • Refresh: Click to refresh to view the current information Statistics Status > Statistics You may want to check the statistical received and transmit packets of the wired and wireless connections of the access point. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Status, and click on Statistics. • Refresh: Click to refresh to view the current information • • Poll Interval: Specify the refresh time interval in the box beside “Poll Interval” and click “Set Interval” to save settings. “Stop” helps to stop the auto refresh of network flow statistics. ARP Table Status > ARP Table You may want to view the access point’s current ARP table. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Status, and click on ARP Table. • Refresh: Click to refresh to view the current information Bridge Table Status > Bridge Table This page allows you to view any active bridge connections to the access point. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Status, and click on Bridge Table. • Refresh: Click to refresh to view the current information

© Copyright 2012 TRENDnet. All Rights Reserved. 48 TRENDnet User’s Guide TEW-715APO DHCP Clients Status > DHCP Clients This page displays the access point’s current DHCP clients. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Status, and click on DHCP Clients. • Refresh: Click to refresh to view the current information Network Activity Status > Network Activity The network activities allows you to monitor the current Wireless and Ethernet TX/RX data traffic in graphical and numerical form on the Web of the Skyport. The chart scale and throughput dimension (Bps, Kbps, Mbps) changes dynamically according to the mean throughput value. 1. Log into the management page (see “Access the management page” on page 9). 2. Click on Status, and click on Network Activity. • Refresh: Click to refresh to view the current information Additional hardware installation Ground wire When placing your device out in an open area where lightning strikes can occur, it is advisable to ground it. This would protect your device from being damage and your network. 1. Loosen and remove the metal O-Ring connected below the optional external N-Type antenna connecter 2. Place the grounding wire into the connecter and tighten the O-Ring 3. Connect the end of the grounding wire to a grounding area. e.g Earth driven rod of grounded system.

© Copyright 2012 TRENDnet. All Rights Reserved. 49 TRENDnet User’s Guide TEW-715APO Using the optional external antenna The access point offers the use of an optional external antenna. This allows you to use an Omni-Type antenna instead of the built in directional antenna. Note: When using the optional external antenna, you must just the antenna settings on the access point to External N-Type. Please refer to the operation mode types you are using for additional information. 1. Remove the black rubber cap off the access point. 2. Connect and fasten tightly your N-Type antenna connector to the access point. Pole mounting The access point comes with a pole mounting clamp that allows you to mount the device to a pole. Note: The mounting clamp supports up to 63mm diameter. 1. Loosen the pole mounting clamp by turn the bolt in of the clamp counter clock wise 2. Insert one end of the clamp through the back (center section) of the access point. 3. Align the access point to the pole and tighten up the clamp till the access point is secured on the pole.

© Copyright 2012 TRENDnet. All Rights Reserved. TRENDnet User’s Guide TEW-715APO 51 Technical Specifications Hardware Standards Wired: IEEE 802.3u Wireless: IEEE 802.11b, IEEE 802.11g, Based on IEEE 802.11n technology LED Indicator Power, LAN, WLAN Antenna 8dBi directional antenna EXT (external antenna connector) N-Type Female connector (up to 15dBi) PoE 12V 1 x 10/100Mbps RJ-45 PoE port, Passive only (non-802.3af compliant) Dimension (L x W x H) 228 x 64 x 61 mm (9.0 x 2.5 x 2.4 in) Weight 500g (17.6 oz) Power Consumption 12 Watts (max.) Management Web browser (HTTP/HTTPS), SNMP (v2c and 3), Telnet, SSH Waterproof IP55 compliant Temperature Operating: -20° ~ 70°C (-4°F ~ 158°F) Storage: -30° ~ 80°C (-22°F ~ 176°F) Humidity Max. 95% (non-condensing) Power Passive PoE power injector DC Output: 12VDC, 1A Input: 100 –240V ~50/60Hz 1A Certifications CE, FCC Wireless Frequency FCC: 2.412 ~ 2.452 ETSI: 2.412 ~ 2.472 Modes Access Point, CPE, Wireless Client AP, AP + Repeater Virtual Access Points 16 Associated Clients (max) 32 (AP Mode), 32 (Repeater Mode) *Coverage 10km line-of-sight Modulation Technique OFDM, BPSK, QPSK, CCK, DQPSK, DBPSK Data Rate (auto-fallback) 802.11b: up to 11Mbps 802.11g: up to 54Mbps 802.11n: up to 135Mbps Security 64/128/152-bit WEP, WPA /WPA2-PSK, WPA/WPA2-RADIUS for AP/CPE mode, WEP/WPA2-PSK for WDS mode MAC filter (32 entries) Output Power 802.11b: 26dBm (typical) 802.11g: 24dBm (typical) 802.11n: 21dBm (typical) Receiving Sensitivity 802.11b: -88dBm (typical) @ 11Mpbs 802.11g: -73dBm (typical) @ 54Mbps 802.11n: -67dBm (typical) @ 150Mbps Channels FCC: 1~11 ETSI: 1~13 *Maximum wireless signal rates are referenced from IEEE 802.11 theoretical specifications. Actual data throughput and coverage will vary depending on interference, network traffic, building materials and other conditions.

© Copyright 2012 TRENDnet. All Rights Reserved. TRENDnet User’s Guide TEW-715APO 52 Troubleshooting Q: I typed http://192.168.10.100 in my Internet Browser Address Bar, but an error message says “The page cannot be displayed.” How can I access the access point management page? Answer: 1. Check your hardware settings again and that all cables are properly connected 2. Make sure the LAN and WLAN lights are lit. 3. Make sure your network adapter TCP/IP settings are set in the subnet class as the access point when accessing with a static IP address or Obtain an IP address automatically (see the steps below). 4. Press on the factory reset button for 15 seconds, the release. Windows 7 a. Go into the Control Panel, click Network and Sharing Center. b. Click Change Adapter Settings, right-click the Local Area Connection icon. c. Then click Properties and click Internet Protocol Version 4 (TCP/IPv4). d. Then click Obtain an IP address automatically and click OK. Windows Vista a. Go into the Control Panel, click Network and Internet. b. Click Manage Network Connections, right-click the Local Area Connection icon and click Properties. c. Click Internet Protocol Version (TCP/IPv4) and then click Properties. d. Then click Obtain an IP address automatically and click OK. Windows XP/2000 a. Go into the Control Panel, double-click the Network Connections icon b. Right-click the Local Area Connection icon and the click Properties. c. Click Internet Protocol (TCP/IP) and click Properties. d. Then click Obtain an IP address automatically and click OK. Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. Q: I am connected to the access point and able to pull DHCP from my network, but I cannot get onto the Internet. What should I do? Answer: 1. Verify that you can get onto the Internet with a direct connection into your router (meaning plug your computer directly to the router and verify that your single computer can access the Internet). 2. Power cycle your modem and router. Unplug the power to the modem and router. Wait 30 seconds, and then reconnect the power to the modem. Wait for the modem to fully boot up, and then reconnect the power to the router. 3. Contact your ISP and verify all the information that you have in regards to your Internet connection settings is correct. Q: I cannot connect wirelessly to the access point. What should I do? Answer: 1. Double check that the WLAN light on the router is lit. 2. Power cycle the access point. Unplug the power to the router. Wait 15 seconds, then plug the power back in to the router. 3. Contact the manufacturer of your wireless network adapter and make sure the wireless network adapter is configured with the proper SSID. The preset SSID is TRENDnet (model_number). 4. Please see “Wireless Performance Consideration” if you continue to have wireless connectivity problems.

© Copyright 2012 TRENDnet. All Rights Reserved. TRENDnet User’s Guide TEW-715APO 54 In MAC 10.4, from the Configure IPv4, drop-down list, select Using DHCP and click the Apply Now button. In MAC 10.5, from the Configure drop-down list, select Using DHCP and click the Apply button. In MAC 10.6, from the Configure drop-down list, select Using DHCP and click the Apply button. f. Restart your computer. Note: If you are experiencing difficulties, please contact your computer or operating system manufacturer for assistance. How to find your MAC address? In Windows 2000/XP/Vista/7, Your computer MAC addresses are also displayed in this window, however, you can type getmac –v to display the MAC addresses only. In MAC OS 10.4, 1. Apple Menu > System Preferences > Network 2. From the Show menu, select Built-in Ethernet. 3. On the Ethernet tab, the Ethernet ID is your MAC Address. In MAC OS 10.5/10.6, 1. Apple Menu > System Preferences > Network 2. Select Ethernet from the list on the left. 3. Click the Advanced button. 3. On the Ethernet tab, the Ethernet ID is your MAC Address. How to connect to a wireless network using the built-in Windows utility? Note: Please note that although the following procedures provided to follow for your operating system on configuring your network settings can be used as general guidelines, however, it is strongly recommended that you consult your computer or operating system manufacturer directly for assistance on the proper procedure for connecting to a wireless network using the built-in utility. Windows 7 1. Open Connect to a Network by clicking the network icon ( or ) in the notification area. 2. In the list of available wireless networks, click the wireless network you would like to connect to, then click Connect. 4. You may be prompted to enter a security key in order to connect to the network. 5. Enter in the security key corresponding to the wireless network, and click OK. Windows Vista 1. Open Connect to a Network by clicking the Start Button. and then click Connect To. 2. In the Show list, click Wireless. 3. In the list of available wireless networks, click the wireless network you would like to connect to, then click Connect. 4. You may be prompted to enter a security key in order to connect to the network. 5. Enter in the security key corresponding to the wireless network, and click OK. Windows XP 1. Right-click the network icon in the notification area, then click View Available Wireless Networks. 2. In Connect to a Network, under Available Networks, click the wireless network you would like to connect to. 3. You may be prompted to enter a security key in order to connect to the network. 4. Enter in the security key corresponding to the wireless network, and click Connect.

© Copyright 2012 TRENDnet. All Rights Reserved. TRENDnet User’s Guide TEW-715APO 55 Internet service types Many Internet Service Providers (ISPs) allow your router to connect to the Internet without verifying the information fields listed below. Skip this section for now and if your router cannot connect to the Internet using the standard installation process, come back to this page and contact your ISP to verify required ISP specification fields listed below. 1. Obtain IP Address Automatically (DHCP) Host Name (Optional) Clone Mac Address (Optional) 2. Fixed IP address WAN IP Address: _____. _____._____._____ (e.g. 215.24.24.129) WAN Subnet Mask: _____. _____._____._____ WAN Gateway IP Address: _____. _____._____._____ DNS Server Address 1: _____. _____._____._____ DNS Server Address 2: _____. _____._____._____ 3. PPPoE to obtain IP automatically User Name: _________ Password: ________________ Verify Password: ________________ 4. PPPoE with a fixed IP address User Name: _________ Password: ________________ Verify Password: ________________ IP Address: ____. _____._____._____ (e.g. 215.24.24.129)

© Copyright 2012 TRENDnet. All Rights Reserved. TRENDnet User’s Guide TEW-715APO 56 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. To avoid the possibility of exceeding radio frequency exposure limits, you shall beep a distance of at least 100cm between you and the antenna of the installed equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user. For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. FCC NOTICE: To comply with FCC part 15 rules in the United States, the system must be professionally installed to ensure compliance with the Part 15 certification. It is the responsibility of the operator and professional installer to ensure that only certified systems are deployed in the United States. The use of the system in any other combination (such as co-located antennas transmitting the same information) is expressly forbidden. Europe – EU Declaration of Conformity Copyright This publication, including all photographs, illustrations and software, is protected under international copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may be reproduced without written consent of the author. Copyright 2006 Trademark recognition All product names used in this manual are the properties of their respective owners and are acknowledged.

© Copyright 2012 TRENDnet. All Rights Reserved. 57 TRENDnet User’s Guide Limited Warranty Limited Warranty TRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of time from the date of purchase. TEW-715APO – 3 Years Warranty AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty. If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defective product or part and deliver an equivalent product or part to the customer. The repair/replacement unit’s warranty continues from the original date of purchase. All products that are replaced become the property of TRENDnet. Replacement products may be new or reconditioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies. TRENDnet shall not be responsible for any software, firmware, information, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty. There are no user serviceable parts inside the product. Do not remove or attempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modified or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to conditions more severe than those specified in the manual. Warranty service may be obtained by contacting TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentation a Return Material Authorization (RMA) number will be issued. An RMA number is required in order to initiate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees. WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDNET’S OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET’S PRODUCTS. TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD. LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE. Governing Law: This Limited Warranty shall be governed by the laws of the state of California. Some TRENDnet products include software code written by third party developers. These codes are subject to the GNU General Public License ("GPL") or GNU Lesser General Public License ("LGPL"). Go to http://www.trendnet.com/gpl or http://www.trendnet.com Download section and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to http://www.gnu.org/licenses/gpl.txt or http://www.gnu.org/licenses/lgpl.txt for specific terms of each license. PWP05202009v2 2012/10/30

Navigation menu