TRENDNET TEW723BRM N300 WiFi ADSL 2+ Modem Router User Manual EN lineart QIG TEW 723BRM V1 CD13 curved

Download:
Mirror Download [FCC.gov]
Document ID	3282721
Application ID	lEB9tOETBR4BT1JygNI/zQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	285.69kB (3571168 bits)
Date Submitted	2017-02-14 00:00:00
Date Available	2017-02-14 00:00:00
Creation Date	2016-12-22 17:39:01
Producing Software	Corel PDF Engine Version 14.0.0.701
Document Lastmod	2016-12-22 19:41:09
Document Title	EN_lineart QIG_TEW-723BRM(V1)(CD13-curved).cdr
Document Creator	CorelDRAW
Document Author:	Administrator

N300 WiFi ADSL 2+ Modem Router
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an uncontrolled environment and it also complies with Part 15 of the FCC RF Rules. This equipment must be installed and operated in
accordance with provided instructions and the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in
conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and consider removing the no-collocation statement.
Caution!
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC - PART 68
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the
format US: TI1DL01ATEW723BRM. If requested, this number must be provided to the telephone company.
This equipment uses the following USOC jacks: RJ-11, RJ-45
REN (RINGER EQUIVALENT NUMBERS) STATEMENT
Notice: The Ringer Equivalence Number (REN: 0.1A) assigned to each terminal device provides an indication of the maximum number of terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the Ringer Equivalence Numbers of all the devices does not exceed 5.
ATTACHMENT LIMITATIONS STATEMENT
Notice: This equipment meets telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment Technical Requirements document(s). This is
confirmed by marking the equipment with the Industry Canada certification number. The Department does not guarantee the equipment will operate to the user's satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications company. The equipment must also be installed using an acceptable
method of connection. The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user to disconnect the equipment.
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and internal metallic water pipe system, if present, are connected together.
This precaution may be particularly important in rural areas. Caution: Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority, or
electrician, as appropriate

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Author                          : Administrator
Create Date                     : 2016:12:22 17:39:01+08:00
Modify Date                     : 2016:12:22 19:41:09+08:00
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Format                          : application/pdf
Creator                         : Administrator
Title                           : EN_lineart QIG_TEW-723BRM(V1)(CD13-curved).cdr
Creator Tool                    : CorelDRAW
Metadata Date                   : 2016:12:22 19:41:09+08:00
GTS PDFX Conformance            : PDF/X-1a:2001
GTS PDFX Version                : PDF/X-1:2001
Version ID                      : 1
Document ID                     : uuid:fe9e8577-c7b6-4077-8ed4-f568a8c8f5aa
Instance ID                     : uuid:9a945756-8dab-49a0-9a4e-42d49e5d6b18
Producer                        : Corel PDF Engine Version 14.0.0.701
Trapped                         : False
Page Count                      : 3

EXIF Metadata provided by EXIF.tools