TRENDNET TEW735AP N300 High Power PoE Access Point User Manual

TRENDNET, Inc. N300 High Power PoE Access Point

UserManual.wiki >

TEW735AP User Manual >

User Manual.pdf

Contents

1. User Manual (Statements).pdf
2. User Manual.pdf

User Manual.pdf

TEW-735AP User’s Guide © Copyright 2013 TRENDnet. All rights reserved. a

TEW-735AP User’s Guide Table of Contents© Copyright 2013 TRENDnet. All rights reserved.Table of ContentsProduct Overview �� 1Package Contents �� 1Features �� 1Front Panel �� 2Mounng Holes �� 2Connectors �� 2Product Pre-set Informaon �� 3Mounng Accessories �� 3Hardware Installaon ��4Mount on Wall or Ceiling �� 4Mount on T-Bar �� 4Wireless Performance Consideraons �� 5Operaon Modes ��5Access Point �� 5WDS Bridge �� 5WDS AP �� 5Universal Repeater�� 5Applicaon Diagram ��6System conguraon ��7System Management and Default Sengs �� 7Log-in System Management for the First Time �� 7Setup Wizard �� 9Status �� 10System �� 13Wireless �� 16Management ��24Federal Communicaon Commission Interference Statement �� 32Europe – EU Declaraon of Conformity ��33RoHS �� 33Limited Warranty �� 35

TEW-735AP User’s Guide Product Overview© Copyright 2013 TRENDnet. All rights reserved. 1Product OverviewPackage ContentsTEW-735AP package includes:• TEW-735AP• Mul-Language Quick Installaon Guide• CD-ROM ( User’s Guide)• Network Cable (1.5 m / 5 .)• Power Adapter (12 V, 1 A)If any package contents are missing or damaged, please contact the retail store, online retailer, or reseller/distributor from which the product was purchased.TEW-735APFeaturesTRENDnet’s plenum rated business class N300 High Power PoE Access Point, model TEW-735AP, greatly increases wireless coverage as compared to standard access points. A variety of installaon scenarios are supported with Access Point, WDS AP, WDS Bridge, and Repeater modes. Save installaon me and costs with PoE. • High power radio greatly expands coverage. Wi-Fi compliant with IEEE 802.11n and IEEE 802.11b/g standards.• Power device by an Ethernet cable using standard IEEE802.3af Power over Ethernet (PoE) protocol• Support Wi-Fi Protected Setup (WPS) for easy conguraon• Proven 300 Mbps wireless n• Supports mulple SSID (up to 4 SSIDs) with 802.1q VLAN tagging (AP mode)• Features Access Point, WDS AP, WDS Bridge, and Repeater modes • Advance wireless security with 64/128-bit WEP, WPA/WPA2 Radius and WPA-PSK/WPA2-PSK• Remote network management and SNMP support (v1, v2c)• O-white housing blends into environment • Plenum rated• 3-year limited warranty *Maximum wireless signal rates are referenced from IEEE 802.11 theorecal specicaons. Actual data throughput and coverage will vary depending on interference, network trac, building materials and other condions.

TEW-735AP User’s Guide Product Overview© Copyright 2013 TRENDnet. All rights reserved. 2Front PanelWirelessNetworkPowerMounng HolesConnectorsDC Power 12V DC 1A(Oponal)10/100 PoE PortMounng holesKensington security slotResetBuonReset Buon • Push and hold for 2 seconds to reset TEW-735AP• Push and hold for more than 10 seconds to reset conguraon to factory default Power LED OFF Powered o or LED display has been disabledON Powered onNetwork LED OFF No network connected through Ethernet port (PoE) or LED display has been disabledON Network connected through Ethernet port (PoE)Flashing Network acvies are detected on Ethernet (PoE) portWireless LED OFF No wireless network connecon or LED display has been disabledFlashing Wireless network acvies are detected

TEW-735AP User’s Guide Product Overview© Copyright 2013 TRENDnet. All rights reserved. 3Product Pre-set InformaonThere are 2 product pre-set labels comes with the package. The rst label is located on top of plasc wrap of TEW-735AP. The second label is on the boom of TEW-735AP. You can nd default SSID, wireless key, administrator account, and administrator password. The default stac management IP has set to 192.168.10.100.Mounng AccessoriesThe mounng accessories are provided for easier hardware installaon, including two sets of T-Bar clipper, two sets of screws, and a set of spacer. P2�6 * 25 ScrewsSpacerP2�6 * 10 Screws15/16” T-Bar Clips 9/16” T-Bar Clips

TEW-735AP User’s Guide Installation© Copyright 2013 TRENDnet. All rights reserved. 4Hardware InstallaonMount on Wall or CeilingUse two P3.5 pan head screws to hold the TEW-735AP. The distance between mounng points is 2 3/4” (7cm)Mount on T-BarTwo addional bronze screw holes are provided for T-Bar mounng. Use two P2.6 screws to secure the TEW-735AP on T-Bar clip and then clip on the T-Bar.

TEW-735AP User’s Guide Installation© Copyright 2013 TRENDnet. All rights reserved. 5Wireless Performance ConsideraonsThere are a number of factors that can impact the range of wireless devices. Adjust your wireless devices so that the signal is traveling in a straight path, rather than at an angle. The more material the signal has to pass through the more signal you will lose. Keep the number of obstrucons to a minimum. Each obstrucon can reduce the range of a wireless device. Posion the wireless devices in a manner that will minimize the amount of obstrucons between them.Building materials can have a large impact on your wireless signal. In an indoor environment, try to posion the wireless devices so that the signal passes through less dense material such as dry wall. Dense materials like metal, solid wood, glass or even furniture may block or degrade the signal.Antenna orientaon can also have a large impact on your wireless signal. Use the wireless adapter’s site survey tool to determine the best antenna orientaon for your wireless devices.Interference from devices that produce RF (radio frequency) noise can also impact your signal. Posion your wireless devices away from anything that generates RF noise, such as microwaves, radios and baby monitors. Any device operang on the 2.4GHz frequency will cause interference. Devices such as 2.4GHz cordless phones or other wireless remotes operang on the 2.4GHz frequency can potenally drop the wireless signal. Although the phone may not be in use, the base can sll transmit wireless signal. Move the phone’s base staon as far away as possible from your wireless devices. Adjust the wireless power seng on your AP if you have more than one AP covering a large area. Covering only the neighbor hop APs in wireless range is a good design. Covering more than neighbor APs will experience wireless interference and slow down the communicaon.Operaon ModesThere are four operang modes provided by TEW-735AP, Access Point, WDS Bridge, WDS, AP and Universal Repeater. Congure the TEW-735AP to dierent operaon mode which service the best in your network. Access PointThis is the default operaon mode. TEW-735AP service wireless end points in this mode. You can setup local or remote wireless authencaon, setup up to 4 sets of SSID and separate SSID or STA trac.WDS BridgeWhen WDS mode is selected, the TEW735AP funcons as a wireless bridge and is able to wirelessly communicate to other WDS bridges to make a wireless backbone. A WDS link is bidireconal; both end points must support WDS and each access point must know the MAC Address of the other. Each access point will be congured with the remote access point’s MAC address and vice versa. Make sure all access points are congured with the same SSID, wireless channel and wireless encrypon sengs.WDS APThis is a hybrid mode. Your TEW735AP can be a WDS bridge and an access point at the same me.Universal RepeaterWhen Repeater Mode is selected, the TEW-735AP funcons as a wireless repeater and is able to repeat the wireless signal of an access point. This feature is used to expand your exisng wireless network on places your current access point is unable to reach. Make sure all the sengs of the TEW-735AP matches the wireless access points you want to repeat in same wireless sengs including SSID, channel and wireless encrypon sengs.

TEW-735AP User’s Guide Installation© Copyright 2013 TRENDnet. All rights reserved. 6Applicaon DiagramWDSWDS APRepeaterAccess PointMultiple SSIDSSID/STA isolation

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 83 Open a web browser and type hp://tew-735ap to access administraon page.If you setup with a stac IP on your PC, please open a web browser and type hp://192.168.10.100 The TEW-735AP login page will show up.Enter administrator login informaon (The default user name is admin and password is printed on device label)* Please reference troubleshoong secon if you cannot access administraon web page.4 Change your administraon login password away from factory default seng. Click Apply to connue.5 TEW-735AP will apply password change and then reboot. Login again with your new password.* Make sure you are sll connecng to TEW-735AP aer reboot if you wireless connects to TEW-735AP.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 9Setup WizardSetup wizard is provided as part of the web conguraon ulity. It sets up the basic administrator password and management IP address by clicking on the Wizard buon on the funcon menu. The following screen will appear. Enter your new administrator password and then click Next to connue.Enter the management IP address for this TEW-735AP. The default IP address is 192.168.10.100. Set it up in your network management subnet with unique IP address. You can leave it on default if you have only one TEW-735AP on network. Click Apply to save changes and reboot TEW-735AP.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 10StatusMain status page shows TEW-735AP basic informaon.SystemOperaon Mode : Shows which one of the 4 modes, Access Point, WDS AP, WDS Bridge, Universal Repeater, is running nowSystem Time : System me on TEW-735AP. This is important for schedule control and correct logging.System Up Time : The me counng from system start up.Hardware Version Hardware version of TEW-735APSerial Number : Serial number of TEW-735APFirmware version : Currently run rmware versionWLAN SengsChannel : Wireless channelSSID_1 - 4 : Service Set Idener. This SSID is human readable and performs as ESSID to setup wireless groups. You can set up to 4 SSID on a single TEW-735AP.Security : Shows what security encrypon is using for this wireless conneconBSSID : Basic SSID. This is strictly unique SSID to idenfy this wireless access point (WAP). It is also the MAC address of the wireless interface.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 11IPv6This page shows TEW-735AP IPv6 link local address. You can manage TEW-735AP using this IPv6 link local address if your computer is IPv6 enabled and in the same broadcast domain. Put a bracket around your IPv6 address to visit the management site. (i.e. hp://[IPv6 address])Wireless Client ListThis page shows all wireless clients connected to this TEW-735AP.Interface : Which SSID the wireless client associated withMAC Address : MAC address of wireless clientRx : Receiving data stascsTx : Transming data stascsSignal(%) : Signal strength of this wireless clientConnected Time : Connecon me since wireless associaonIdle Time : Accumulated non acve meRefresh : Click this buon to refresh the list

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 12System LogThis page allows users to view a running log of the access point system stascs, events and acvies. Save : Click this buon to save the log to your computerClear : Click this buon to clear up the logRefresh : Click this buon to refresh the logMulple LanguageYou can choose the language you preferred on login page. Or, you can change your language seng here.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 13SystemOperaon ModeYou can choose one of the mode to t your network plan: Access Point, WDS AP, WDS Bridge and Universal Repeater.Access PointThis is the default operaon mode. Wireless clients, known as wireless staons (STAs), can wireless associate with TEW-735AP and connect to Internet via Ethernet port.WDS APIn this operaon mode. TEW-735AP wireless connects to other WDS (Wireless Distribuon System) for backbone communicaon and provides wireless connecon to clients (STAs) at the same me.WDS BridgeIn this operaon mode. TEW-735AP connects ONLY to other WDS (Wireless Distribuon System) as a backbone bridge.Universal RepeaterTEW-735AP repeats wireless signal and packets in this mode for backbone communicaon as well as client access. This feature is used to expand your exisng wireless network on places your current access point is unable to reach. Make sure all the sengs of the TEW-735AP matches to your root or connecng wireless access points, same SSID, channel and wireless encrypon sengs.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 14IP SengsThe TEW-735AP has a stac IP 192.168.10.100 set in factory for management purpose. You can change this IP address to t your network plan or manage mulple TEW-735AP. You can also set TEW-735AP to DHCP client accepng IP dynamically.Bridge Type : Select Stac IP or Dynamic IP from the drop-down list. If you select Stac IP, you will be required to specify an IP address and subnet mask. If Dynamic IP is selected, then the IP address is received automacally from the external DHCP server.IP Address : Specify an IP addressIP Subnet Mask : Specify a subnet mask for the IP addressDefault Gateway : Default route for TEW-735APDNS Type : Stac or DynamicFirst DNS Address : Primary DNS server addressSecond DNS Address : Secondary DNS server addressDHCP ServerTEW-735AP equipped with DHCP server assigning IPv4 addresses dynamically. The assigning IP address range must be in the subnet which is setup in IP Sengs. By default, the DHCP server is disabled. If you want to enable it, select Enabled from the DHCP Server drop down list. Enter following informaon and click Apply to save the change and acve DHCP server.DHCP Server : Choose Enabled or Disabled from the drop down list.Lease Time : How long the assigning IP will be validStart IP : Starng IP address of DHCP poolEnd IP : Last IP address of DHCP poolFirst DNS Address : Primary DNS server address you want to assign with DHCP leaseSecond DNS Address : Secondary DNS server address you want to assign with DHCP lease

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 15Spanning TreeTEW-735AP is designed for terminal access as well as backbone connecon. To avoid network looping, you can enable 802.1d spanning tree protocol.Spanning Tree Status: Enable or disable 802.1d spanning tree protocol to avoid network loopingBridge Hello Time : The me between each bridge protocol data unit (BPDU). Default: 2 sec.Bridge Max Age : Maximum me a BPDU kept in bridge. Default: 20 sec.Bridge Forward Delay : The me spend in listen and learning state. Default: 15 sec.Bridge Priority : Priority number for root bridge selecon. (MAC number is listed on Status > Main page) Apply : Click this buon to save and acvateCancel : Click this buon to abandon the change

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 16WirelessBasicGeneral setups for your wireless connecon. You can setup up to four SSIDs for dierent group of users. Radio : Enable or disable overall wireless signalsMode : The operaon mode seng in System seconBand : Choose the Wi-Fi connecon protocols you want to run on APEnabled SSID# : Choose the number of SSIDs you want to enable (Range: 1 ~ 4)ESSID1 - 4 : SSID names for enabled groupsAuto Channel : Enable or disable auto channel seleconChannel : (for Fixed Channel) specify channel numberCheck Channel Time :(for Auto Channel) specify how frequently TEW-735AP is checking the channel statusApply : Click this buon to apply the changeCancel : Click this buon to abandon the change

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 17SecuritySet up wireless security sengs in this page. Select SSID you want to set up, change the value and then click on Apply to commit the changes. Enabling security prevents any unauthorized wireless clients to connect into your network.ESSID Selecon : Select the SSID you want to set up wireless securitySeparate : SSID: If you check this box, clients associated with this SSID cannot communicate with wireless clients associated with other SSID directly.STA: If you check this box, wireless clients (a.k.a. STA) associated with this SSID cannot communicate to each other directly. Even they are in the same wireless group.Broadcast ESSID : Select Enable or Disable from the drop-down list. This is the SSID broadcast feature. When this opon is set to Enable, your wireless network name is broadcast to anyone within wireless signal range. When this is disabled, you must enter the Wireless Network Name (SSID) on the client manually to connect to the network�WMM : Choose to Enable or Disable WMM. This is the Quality of Service (QoS) feature for priorizing voice and video applicaons.Encrypon : Choose between disable, WEP, WPA, WPA2 or 802.1x for your wireless security. Encrypon (Disabled) : Choosing disable allow wireless clients connects to TEW-735AP without passwordYou can relay the authencaon to remote RADIUS server by checking Enable 802.1x Authencaon and entering RADIUS server informaon.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 18Encrypon (WEP) : WEP, Wire Equivalent Protecon, provides a basic wireless securityAuthencaon Type : Select Open System, Shared Key, or auto.Open System allows any client to authencate as long as it conforms to any MAC address lter policies that may have been set. All authencaon packets are transmied without encrypon.Shared Key sends an unencrypted challenge text string to any device aempng to communicate with the AP. The device requesng authencaon encrypts the challenge text and sends it back to the access point. If the challenge text is encrypted correctly, the access point allows the requesng device to authencate. It is recommended to select Auto if you are not sure which authencaon type is used.Key Length : Select a 64-bit or 128-bit WEP key length from the drop-down listKey Type : Select a key type from the drop-down list. 128-bit encrypon requires a longer key than 64-bit encrypon. Keys are dened by entering in a string in HEX (hexadecimal - using characters 0-9, A-F) or ASCII (American Standard Code for Informaon Interchange - alphanumeric characters) format. ASCII format is provided so you can enter a string that is easier to rememberDefault Key : You may choose one of your 4 dierent WEP keys from belowEncrypon Key 1-4 : You may enter four dierent WEP keysEnable 802.1x Authencaon :Check on this box if you would like to use stac WEP plus 802.1x authencaon. This opon works with a RADIUS Server to authencate wireless clients. Wireless clients can either use Stac WEP or 802.1x authencaon in order to connect to the network. For 802.1x, clients should have necessary credenals to be authencated by the Server. Furthermore, it is necessary to specify the RADIUS Server’s IP address, service port number, and shared secret.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 19Encrypon (WPA pre-shared key) :Wi-Fi Protected Access (WPA) pre-shared keyWPA Type : Select TKIP, AES, or WPA2 Mixed. The encrypon algorithm used to secure the data communicaon. TKIP (Temporal Key Integrity Protocol) provides per-packet key generaon and is based on WEP. AES (Advanced Encrypon Standard) is a very secure block based encrypon. Note that, if the bridge uses the AES opon, the bridge can associate with the access point only if the access point is also set to use only AES.Pre-shared Key Type : The Key Type can be passphrase or Hex formatPre-shared Key : The key is entered as a pass-phrase of up to 63 alphanumeric characters in ASCII (American Standard Code for Informaon Interchange) format at both ends of the wireless connecon. It cannot be shorter than eight characters, although for proper security it needs to be of ample length and should not be a commonly known phrase. This phrase is used to generate session keys that are unique for each wireless clientEncrypon (WPA RADIUS) :Use RADIUS server manage your wireless authencaon keys for easier account managementWPA Type : Select TKIP, AES, or WPA2 Mixed. The encrypon algorithm used to secure the data communicaon. TKIP (Temporal Key Integrity Protocol) provides per-packet key generaon and is based on WEP. AES (Advanced Encrypon Standard) is a very secure block based encrypon. Note that, if the bridge uses the AES opon, the bridge can associate with the access point only if the access point is also set to use only AES.RADIUS Server IP Address :IP address of RADIUS serverRADIUS Server Port : RADIUS service port number. Default: 1812RADIUS ServerShared Secret:RADIUS service shared secret to authencate this credenal agent.Apply : Click this buon to apply the changeCancel : Click this buon to abandon the change

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 20AdvancedFine tuning your wireless sengs on this page. Fragment Threshold : Packets over the specied size will be fragmented in order to improve performance on noisy networks. Specify a value between 256 and 2346. The default value is 2346.RTS Threshold : Packets over the specied size will use the RTS/CTS mechanism to maintain performance in noisy networks and prevenng hidden nodes from degrading the performance. Specify a value between 0 and 2347. The default value is 2347Beacon Interval : Beacons are packets sent by a wireless Access Point to synchronize wireless devices. Specify a Beacon Interval value between 24 and 1024. The default value is set to 100 milliseconds.DTIM Period : A DTIM is a countdown informing clients of the next window for listening to broadcast and mulcast messages. When the wireless Access Point has buered broadcast or mulcast messages for associated clients, it sends the next DTIM with a DTIM Period value. Wireless clients detect the beacons and awaken to receive the broadcast and mulcast messages. The default value is 1. Valid sengs are between 1 and 10�Data rate : You can select a data rate from the drop-down list, however, it is recommended to select auto. In auto mode, TEW735AP will choose the maximum data rate to t the instant wireless channel quality automacally.N Data Rate : Select dierent 802.11N Modulaon and Coding Scheme (MCS) against parcular wireless noise. Or, select auto leng TEW-735AP select MCSs dynamically.Channel Bandwidth : Select channel bandwidth for1) Dynamic select 20 MHz and 40MHz bandwidth or 2) choose 20MHz channels only�Preamble Type : Select a short or long preamble. For opmum performance it is recommended to also congure the client device to the same preamble type.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 21CTS Protecon : Clear to Send, CTS, can be always enabled, auto, or disabled. By enabled CTS, the Access Point and clients will wait for a ‘channel cleared’ signal before transming. It is recommended seng to auto�Tx Power : Wireless signal transmission power. Set transmission power to appropriate value can make your mulple AP deployment easier. The default value is 26 dBm. Valid sengs are between 11 and 29.Apply : Click this buon to apply the changeCancel : Click this buon to abandon the changeMAC FilterSet up a list of clients and policy allow only clients on the list associate with this AP or reject clients on the list associate with this AP. Set up the list with MAC addresses. A MAC address is a unique ID assigned by the manufacture of the network adapter.Enable WirelessAccess Control :Check this box to enable feature (Click Apply to commit the change)Deny / Allow Policy : Choose “ Deny all clients with MAC address listed below to access the network” will allow clients not on the list to associate with TEW-735AP.Choose “ Allow all clients with MAC address listed below to access the network” will deny clients not on the list to associate with TEW-735AP.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 22Encrypon : MAC address: Enter the device’s MAC addressADD: Click to add MAC address into tableReset: Click to reset entry Delete Selected: Allows you to delete selected entryDelete All: Deletes all entries in the MAC address table Reset: Reset all entriesApply: Click to apply changes madeCancel: Click to cancel any new seng changes made. Descripon : Enter readable informaon about this clientMAC Address : Enter the device’s MAC addressAdd : Click this buon to add MAC address onto the listReset : Click this buon to abandon the changeDelete Selected :Click this buon to delete selected entryDelete All : Click this buon to clear up the listReset : Click this buon to abandon the changeApply : Click this buon to apply the changeCancel : Click this buon to abandon the change

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 23WPSWPS is the simplest way to connect a wireless client to TEW-735AP. You don’t have to select the encrypon mode and ll in a long encrypon passphrase every me when you try to setup a wireless connecon. You only need to press a buon on both wireless client and TEW-735AP, and the WPS will do the rest for you. The TEW-735AP supports two types of WPS: WPS via Push Buon and WPS via PIN code. If you want to use the Push Buon, you have to push a specic buon on the wireless client or in the ulity of the wireless client to start the WPS pairing, and click the Start to Process buon in this page under WPS via Push Buon to start WPS pairing. If you want to use the PIN code, you have to know the PIN code of the wireless client and switch it to WPS mode, then ll-in the PIN code of the wireless client through the web conguraon interface of the wireless router.WPS : Check this box to enable featureWPS Current Status : Displays the current status of the WPS conguraonSelf Pin Code : Displays PIN code of TEW-735APSSID : Displays the SSID for WPS pairing. Only the rst SSID (SSID_1) can proceed WPS pairing.Authencaon Mode :Displays the authencaon mode of SSID_1Passphrase Key : Current passphraseWPS Via Push Buon :Click on the Start to Process buon if you would like to enable WPS through the Push Buon instead of the PIN. Aer pressing this buon you will be required to press the WPS on the client device within two minutes. Click on the OK buon in the dialog boxWPS via PIN : Specify a PIN, which unique number that can be used to add the router to an exisng network or to create a new network. Then click on the Start to Process buon

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 24ManagementAdministraonChange the password required to log into the access point’s web-based management. Passwords can contain 0 to 12 alphanumeric characters, and are case sensive. Enter your password and system informaon and then click Apply to save the change.Old Password: Type in the current password to allow changing to a new password.New Password: Enter your new password here.Conrm Password: Type your new password again for vericaon purposesSystem Name: The system name can be idened on your local network. Changing this system name can change the way you access this AP. For example, if you change the system name to “lobbyfront”, you can access this AP by typing hp://lobbyfront/ in Windows and log on to the management page. Default system name is “tew-735ap”.Idle Timeout

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 25Management VLANThis feature is only available under Access Point or WDS AP mode and allows users to congure the 802.1q VLAN sengs to for all wireless clients. Enter VLAN ID you want to tag to clients associated with specic SSID. Dierent SSID should set to dierent VLAN ID. Enable Virtual LAN service and click Apply to save the changes.LAN VLAN MGMT is a special VLAN to manage TEW-735AP. Enabling management VLAN tagging will keep all services, for example DHCP server and client, in this VLAN.Virtual LAN : Choose to Enable or Disable the VLAN featuresSSID 1 - 4 Tag : Enter VLAN tag you want to add for associated clients. Check the leading check box to enable tagging. All SSIDs have to have dierent VLAN tag. Valid sengs are between 1 and 4094.LAN VLAN MGMT : Enable or disable TEW-735AP services on a specic VLAN. If management VLAN tagging is enabled. All service packets, including web management, DHCP server/ client, will be tagged with specied tag.MGMT Tag : VLAN number for TEW-735AP services. This number has to be dierent to all above VLAN numbers.Apply : Click this buon to apply the changeCancel : Click this buon to abandon the change

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 26SNMP SengSNMP Seng allows you to assign the contact details, locaon, community name and trap sengs for SNMP. This is a networking management protocol used to monitor network-aached devices. SNMP allows messages (called protocol data units) to be sent to various parts of a network. Upon receiving these messages, SNMP-compable devices (called agents) return data stored in their Management Informaon Bases.SNMP Acve : Choose to enable or disable the SNMP featureSNMP Version : Select SNMP version from the drop-down listSNMP Manager IP : Specify the the SNMP manager IP addressRead Community Name : Specify the password for access the SNMP community for read only accessSet Community Name : Specify the password for access to the SNMP community with read/write accessSystem Locaon : Specify the locaon of the TEW-735APSystem Contact : Specify the contact details of the TEW-735APTrap Acve : Choose to enable or disable the SNMP trapping featureTrap Manager IP : Specify the password for the SNMP trap communityTrap Community : Specify the name of SNMP trap communityApply : Click this buon to apply the changeCancel : Click this buon to abandon the change

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 27Backup / Restore SengsThis page allows you to save the current conguraons. Click Save to save your current conguraon. To load conguraons saved previously, click Browse �� to nd conguraon le and then click Upload� In case you want to reset TEW-735AP conguraon back to factory default, click Reset in this page. All conguraons will be set back to its original default sengs.Auto Reboot SengsClick on Apply, the TEW-735AP will going through all the reboot process automacally.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 28Firmware UpgradeTRENDnet may periodically release rmware upgrades that might add features or x problems associated with your TRENDnet model and version. To nd out if there is a rmware upgrade available for your device, please check your TRENDnet model and version using the link. hp://www.trendnet.com/downloads/1� If a rmware upgrade is available, download the rmware to your computer.2� Unzip the le to a folder on your computer.3� Log into the TEW-735AP4� Click on Management and then Firmware Upgrade5� Click Browse�� and navigate to the folder on your computer in which the unzipped rmware le (.bin) is.6� Located and select it the rmware le.7� Click Apply�Time SengThe Time Seng allows your access point to reference or base its me on the sengs congured here, which will aect funcons such as log entries and schedules. Time Setup : Choose a source of me to synchronize with. You can choose to synchronize the TEW-735AP with a NTP server or your PC.Time Zone : Select the me zone of the country you are currently in. The TEW-735AP will set its me based on your selecon.NTP Time Server : Specify a me server (NTP server) to synchronize with. (e.g. pool.ntp.org)Daylight Savings : Check this box if your me zone has daylight savings.DST Start / DST End : Specify the starng date and end date of daylight savings.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 29Apply : Click this buon to apply the changeCancel : Click this buon to abandon the changeScheduleService schedule can be set up daily or weekly for power saving and security reason. Click Add to add a schedule rule entry. Select an entry and click Edit or Delete Selected to change the entry. Click Delete All to remove all entries. Aer schedule eding, click Apply to save your schedule. Check Enabled Schedule Table to make AP services work with schedule.Add :Add scheduled serviceEdit :Edit selected scheduled serviceDelete Selected :Delete selected scheduled serviceDelete All :Click this buon to clear up the listApply : Click this buon to apply the changeCancel : Click this buon to abandon the change

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 30DiagnosisTo check your network connecon, you can use the PING tool from your TEW-735AP. Enter the IPv4 address you want to ping and click Start� The result will be showed in the terminal down below.LED ControlAll LED indicators are turned on by default. You can turn any one of them or all of them on or o. Click the LED you want to change the acon and then click Apply to save the changes.

TEW-735AP User’s Guide System Conguration© Copyright 2013 TRENDnet. All rights reserved. 31Logout Logout from the management page. The TEW-735AP allows only one management login at the same me. If you want to access the TEW-735AP from dierent computer, remember to logout the web management page rst.

TEW-735AP User’s Guide FCC Interference Statement© Copyright 2013 TRENDnet. All rights reserved. 32Federal Communicaon Commission Interference StatementThis equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the following measures:• Reorient or relocate the receiving antenna.• Increase the separaon between the equipment and receiver.• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.• Consult the dealer or an experienced radio/TV technician for help.FCC Cauon: Any changes or modicaons not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. IMPORTANT NOTE:FCC Radiaon Exposure Statement:This equipment complies with FCC radiaon exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.This transmier must not be co-located or operang in conjuncon with any other antenna or transmier.The availability of some specic channels and/or operaonal frequency bands are country dependent and are rmware programmed at the factory to match the intended desnaon. The rmware seng is not accessible by the end user�

TEW-735AP User’s Guide Declaration of Conformity© Copyright 2013 TRENDnet. All rights reserved. 33Europe – EU Declaraon of ConformityThis device complies with the essenal requirements of the R&TTE Direcve 1999/5/EC, 2006/95/EC and 2009/125/EC.. The following test methods have been applied in order to prove presumpon of conformity with the essenal requirements of the R&TTE Direcve 1999/5/EC, 2006/95/EC and 2009/125/EC:EN 60950-1:2006+A11:2009+A1:2010+A12:2011IEC 60950-1:2005 (2nd Edion) Am 1:2009Safety of Informaon Technology EquipmentEN50385 : 2002Generic standard to demonstrate the compliance of electronic and electrical apparatus with the basic restricons related to human exposure to electromagnec elds (0 Hz - 300 GHz)EN 300 328 V1.7.1Electromagnec compability and Radio spectrum Maers (ERM); Wideband transmission systems; Data transmission equipment operang in the 2,4 GHz ISM band and using wide band modulaon techniques; Harmonized EN covering essenal requirements under arcle 3.2 of the R&TTE DirecveEN 301 489-1 V1.9.2 Electromagnec compability and Radio Spectrum Maers (ERM); ElectroMagnec Compability (EMC) standard for radio equipment and services; Part 1: Common technical requirementsEN 301 489-17 V2.2.1Electromagnec compability and Radio spectrum Maers (ERM); ElectroMagnec Compability (EMC) standard for radio equipment and services; Part 17: Specic condions for 2,4 GHz wideband transmission systems and 5 GHz high performance RLAN equipmentThis device is a 2.4 GHz wideband transmission system (transceiver), intended for use in all EU member states and EFTA countries, except in France and Italy where restricve use applies.In Italy the end-user should apply for a license at the naonal spectrum authories in order to obtain authorizaon to use the device for seng up outdoor radio links and/or for supplying public access to telecommunicaons and/or network services.This device may not be used for seng up outdoor radio links in France and in some areas the RF output power may be limited to 10 mW EIRP in the frequency range of 2454 – 2483.5 MHz. For detailed informaon the end-user should contact the naonal spectrum authority in France.RoHSThis product is RoHS compliant.

TEW-735AP User’s Guide Declaration of Conformity© Copyright 2013 TRENDnet. All rights reserved. 34cs Česky [Czech]TRENDnet mto prohlašuje, že tento TEW-735AP je ve shodě se základními požadavky a dalšími příslušnými ustanoveními směrnice 1999/5/ES, 2006/95/ES, a 2009/125/ES.da Dansk [Danish]Undertegnede TRENDnet erklærer herved, at følgende udstyr TEW-735AP overholder de væsentlige krav og øvrige relevante krav i direkv 1999/5/EF, 2006/95/EF, og 2009/125/EF.de Deutsch [German]Hiermit erklärt TRENDnet, dass sich das Gerät TEW-735AP in Übereinsmmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Besmmungen der Richtlinie 1999/5/EG, 2006/95/EG und 2009/125/EG bendet.et Ees [Estonian]Käesolevaga kinnitab TRENDnet seadme TEW-735AP vastavust direkivi 1999/5/EÜ, 2006/95/EÜ ja 2009/125/EÜ põhinõuetele ja nimetatud direkivist tulenevatele teistele asjakohastele sätetele.en English Hereby, TRENDnet, declares that this TEW-735AP is in compliance with the essenal requirements and other relevant provisions of Direcve 1999/5/EC, 2006/95/EC, and 2009/125/EC.es Español [Spanish]Por medio de la presente TRENDnet declara que el TEW-735AP cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Direcva 1999/5/CE, 2006/95/CE, 2009/125/CE y.el Ελληνική [Greek]ΜΕ ΤΗΝ ΠΑΡΟΥΣΑ TRENDnet ΔΗΛΩΝΕΙ ΟΤΙ TEW-735AP ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ ΑΠΑΙΤΗΣΕΙΣ ΚΑΙ ΤΙΣ ΛΟΙΠΕΣ ΣΧΕΤΙΚΕΣ ΔΙΑΤΑΞΕΙΣ ΤΗΣ ΟΔΗΓΙΑΣ 1999/5/ΕΚ, 2006/95/ΕΚ, 2009/125/ΕΚ και.fr Français [French]Par la présente TRENDnet déclare que l’appareil TEW-735AP est conforme aux exigences essenelles et aux autres disposions pernentes de la direcve 1999/5/CE, 2006/95/CE, 2009/125/CE et�it Italiano [Italian]Con la presente TRENDnet dichiara che questo TEW-735AP è conforme ai requisi essenziali ed alle altre disposizioni pernen stabilite dalla direva 1999/5/CE, 2006/95/CE e 2009/125/CE.lv Latviski [Latvian]Ar šo TRENDnet deklarē, ka TEW-735AP atbilst Direkvas 1999/5/EK, 2006/95/EK, un 2009/125/EK būskajām prasībām un ciem ar to saistajiem noteikumiem.lt Lietuvių [Lithuanian] Šiuo TRENDnet deklaruoja, kad šis TEW-735AP anka esminius reikalavimus ir kitas 1999/5/EB, 2006/95/EB ir 2009/125/EB Direktyvos nuostatas.nlNederlands [Dutch]Hierbij verklaart TRENDnet dat het toestel TEW-735AP in overeenstemming is met de essenële eisen en de andere relevante bepalingen van richtlijn 1999/5/EG, 2006/95/EG, en 2009/125/EG.mt Mal [Maltese]Hawnhekk, TRENDnet, jiddikjara li dan TEW-735AP jikkonforma mal-ħġijiet essenzjali u ma provvedimen oħrajn relevan li hemm d-Dirreva 1999/5/KE, 2006/95/KE, u 2009/125/KE.hu Magyar [Hungarian]Alulíro, TRENDnet nyilatkozom, hogy a TEW-735AP megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EK irányelv, a 2006/95/EK és a 2009/125/EK irányelv egyéb elõírásainak�pl Polski [Polish]Niniejszym TRENDnet oświadcza, że TEW-735AP jest zgodny z zasadniczymi wymogami oraz pozostałymi stosownymi postanowieniami Dyrektywy 1999/5/WE, 2006/95/WE i 2009/125/WE.pt Português [Portuguese]TRENDnet declara que este TEW-735AP está conforme com os requisitos essenciais e outras disposições da Direcva 1999/5/CE, 2006/95/CE e 2009/125/CE.sl Slovensko [Slovenian]TRENDnet izjavlja, da je ta TEW-735AP v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direkve 1999/5/ES, 2006/95/ES, a 2009/125/ES.sk Slovensky [Slovak]TRENDnet týmto vyhlasuje, že TEW-735AP spĺňa základné požiadavky a všetky príslušné ustanovenia Smernice 1999/5/EF.Suomi [Finnish]TRENDnet vakuuaa täten eä TEW-735AP tyyppinen laite on direkivin 1999/5/EY, 2006/95/EY ja 2009/125/EY oleellisten vaamusten ja sitä koskevien direkivin muiden ehtojen mukainen.sv Svenska [Swedish]Härmed intygar TRENDnet a denna TEW-735AP står I överensstämmelse med de väsentliga egenskapskrav och övriga relevanta bestämmelser som framgår av direkv 1999/5/EG, 2006/95/EG och 2009/125/EG.

TEW-735AP User’s Guide Warranty© Copyright 2013 TRENDnet. All rights reserved. 35Limited WarrantyTRENDnet warrants its products against defects in material and workmanship, under normal use and service, for the following lengths of me from the date of purchase.• TEW-735AP – 3 Years Warranty• AC/DC Power Adapter, Cooling Fan, and Power Supply carry 1 year warranty.If a product does not operate as warranted during the applicable warranty period, TRENDnet shall reserve the right, at its expense, to repair or replace the defecve product or part and deliver an equivalent product or part to the customer. The repair/replacement unit’s warranty connues from the original date of purchase. All products that are replaced become the property of TRENDnet. Replacement products may be new or recondioned. TRENDnet does not issue refunds or credit. Please contact the point-of-purchase for their return policies.TRENDnet shall not be responsible for any soware, rmware, informaon, or memory data of customer contained in, stored on, or integrated with any products returned to TRENDnet pursuant to any warranty.There are no user serviceable parts inside the product. Do not remove or aempt to service the product by any unauthorized service center. This warranty is voided if (i) the product has been modied or repaired by any unauthorized service center, (ii) the product was subject to accident, abuse, or improper use (iii) the product was subject to condions more severe than those specied in the manual.Warranty service may be obtained by contacng TRENDnet within the applicable warranty period and providing a copy of the dated proof of the purchase. Upon proper submission of required documentaon a Return Material Authorizaon (RMA) number will be issued. An RMA number is required in order to iniate warranty service support for all TRENDnet products. Products that are sent to TRENDnet for RMA service must have the RMA number marked on the outside of return packages and sent to TRENDnet prepaid, insured and packaged appropriately for safe shipment. Customers shipping from outside of the USA and Canada are responsible for return shipping fees. Customers shipping from outside of the USA are responsible for custom charges, including but not limited to, duty, tax, and other fees.WARRANTIES EXCLUSIVE: IF THE TRENDNET PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, THE CUSTOMER’S SOLE REMEDY SHALL BE, AT TRENDNET’S OPTION, REPAIR OR REPLACE. THE FOREGOING WARRANTIES AND REMEDIES ARE EXCLUSIVE AND ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. TRENDNET NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION MAINTENANCE OR USE OF TRENDNET’S PRODUCTS.TRENDNET SHALL NOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THAT THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOMER’S OR ANY THIRD PERSON’S MISUSE, NEGLECT, IMPROPER INSTALLATION OR TESTING, UNAUTHORIZED ATTEMPTS TO REPAIR OR MODIFY, OR ANY OTHER CAUSE BEYOND THE RANGE OF THE INTENDED USE, OR BY ACCIDENT, FIRE, LIGHTNING, OR OTHER HAZARD.LIMITATION OF LIABILITY: TO THE FULL EXTENT ALLOWED BY LAW TRENDNET ALSO EXCLUDES FOR ITSELF AND ITS SUPPLIERS ANY LIABILITY, WHETHER BASED IN CONTRACT OR TORT (INCLUDING NEGLIGENCE), FOR INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY KIND, OR FOR LOSS OF REVENUE OR PROFITS, LOSS OF BUSINESS, LOSS OF INFORMATION OR DATE, OR OTHER FINANCIAL LOSS ARISING OUT OF OR IN CONNECTION WITH THE SALE, INSTALLATION, MAINTENANCE, USE, PERFORMANCE, FAILURE, OR INTERRUPTION OF THE POSSIBILITY OF SUCH DAMAGES, AND LIMITS ITS LIABILITY TO REPAIR, REPLACEMENT, OR REFUND OF THE PURCHASE PRICE PAID, AT TRENDNET’S OPTION. THIS DISCLAIMER OF LIABILITY FOR DAMAGES WILL NOT BE AFFECTED IF ANY REMEDY PROVIDED HEREIN SHALL FAIL OF ITS ESSENTIAL PURPOSE.Governing Law: This Limited Warranty shall be governed by the laws of the state of California.Some TRENDnet products include soware code wrien by third party developers. These codes are subject to the GNU General Public License (“GPL”) or GNU Lesser General Public License (“LGPL”). Go to hp://www.trendnet.com/gpl or hp://www.trendnet.com Download secon and look for the desired TRENDnet product to access to the GPL Code or LGPL Code. These codes are distributed WITHOUT WARRANTY and are subject to the copyrights of the developers. TRENDnet does not provide technical support for these codes. Please go to hp://www.gnu.org/licenses/gpl.txt or hp://www.gnu.org/licenses/lgpl.txt for specic terms of each license.DRAFTTEW-735AP User’s Guide V1.0

TEW-735AP User’s Guide Warranty© Copyright 2013 TRENDnet. All rights reserved. 36