TRENDNET TEW829DRU AC3000 Tri-Band Wireless Gigabit Dual-WAN VPN SMB Router User Manual Statement

Download:
Mirror Download [FCC.gov]
Document ID	3759618
Application ID	sNTh3utF6aGRBcMnpl1VMQ==
Document Description	User Manual Statement
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	11.83kB (147873 bits)
Date Submitted	2018-02-23 00:00:00
Date Available	2018-08-25 00:00:00
Creation Date	2018-02-22 17:40:58
Producing Software	Microsoft® Word 2016
Document Lastmod	2018-02-22 18:17:29
Document Title	User Manual Statement
Document Creator	Microsoft® Word 2016
Document Author:	David Heald

SAFETY, REGULATORY, AND WARRANTY GUIDE
This device has been designed to operate with cellular antennas having a
maximum gain of 3 dBi. Antennas having a higher gain are strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50
ohms.
TRENDNET MODEL: TEW-829DRU
This important Safety, Regulatory, and Warranty Guide contains safety,
handling, disposal, regulatory, trademark, copyright, and software licensing
information.
Read all safety information below and operating instructions before using the
device to avoid injury.
These devices have been designed to operate with WiFi antennas having a
maximum gain of 5 dBi. Antennas having a higher gain are strictly prohibited
per regulations of Industry Canada. The required antenna impedance is 50
ohms.
THIS DEVICE REQUIRES PROFESSIONAL INSTALLATION
FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one of the
following measures:
• Reorient or relocate the receiving antenna.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Increase the separation between the equipment and receiver.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
DÉCLARATION D’INDUSTRIE CANADA
Le présent appareil est conforme aux CNR d'ISED applicables aux appareils
radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.
Pour les produits disponibles aux États-Unis / Canada du marché, seul le canal
1 à 11 peuvent être exploités. Sélection d'autres canaux n'est pas possible.
les dispositifs fonctionnant dans la bande 5150-5250 MHz sont réservés
uniquement pour une utilisation à l’intérieur afin de réduire les risques de
brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes
canaux.
NOTE IMPORTANTE (POUR L’UTILISATION DE DISPOSITIFS MOBILES):
DÉCLARATION D’EXPOSITION AUX RADIATIONS
Cet équipement est conforme aux limites d'exposition aux rayonnements IC
établies pour un environnement non contrôlé. Cet équipement doit être
installé et utilisé avec un minimum de 20 cm de distance entre la source de
rayonnement et votre corps.
Cet appareil et son antenne (s) ne doit pas être co-localisés ou fonctionnement
en association avec une autre antenne ou transmetteur.
Operation of the 5 GHz WiFi radios is restricted to indoor use only.
Le présent émetteur radio (IC: 6921A-S7A741A, 5131A-LM940) a été approuvé
par Industrie Canada pour fonctionner avec les types d'antenne énumérés cidessous et ayant un gain admissible maximal et l'impédance requise pour
chaque type d'antenne. Les types d'antenne non inclus dans cette liste, ou dont
le gain est supérieur au gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance of 21 cm between the radiator and your body.
Ce dispositive a ete concu pour fonctionner ave une antenna cellulaire ayant un
gain maximal de 3 dBi. Une antenne a gain plus eleve est strictement interdite
par les reglemnets d’Industrie Canada. L’impedance d’antenne requise est de
50 ohms.
FCC STATEMENT
For product available in the USA/Canada market, only channel 1-11 can be
operated. Selection of other channels is not possible.
This device and its antennas(s) must not be co-located or operating in
conjunction with any other antenna or transmitter except in accordance with
FCC multi-transmitter product procedures.
Ce dispositive a ete concu pour fonctionner ave une antenna WiFi ayant un gain
maximal de 5 dBi. Une antenne a gain plus eleve est strictement interdite par
les reglemnets d’Industrie Canada. L’impedance d’antenne requise est de 50
ohms.
To comply with FCC regulations limiting both maximum RF output power and
human exposure to RF radiation, the maximum cellular antenna gain must not
exceed 3.3 dBi, except when operation in Band 30 is not disabled.
To comply with FCC regulations limiting both maximum RF output power and
human exposure to RF radiation, the maximum WiFi antenna gain must not
exceed 5 dBi.
INFORMATION FOR EUROPE, DECLARATION OF COMPLIANCE
TRENDnet, Inc.
20675 Manhattan Place
Torrance, CA 90501 USA
Tel.: (310) 961-5500
INDUSTRY CANADA STATEMENT
This device complies with ISED’s license-exempt RSS standards. Operation is
subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Hereby, TRENDnet Inc. declares that this equipment is in compliance with the
Radio Equipment Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following
internet address: TRENDnet.com/product-certifications
RESTRICTIONS ON USE IN THE EU
BE BG CZ DK DE EE IE
EL ES FR HR IT CY LV
LT LU HU MT NL AT PL
PT RO SI SK FI SE UK
5 GHz 802.11 a/n/ac WiFi radios are restricted to indoor use only. The 5GHz
WiFi radio in this device must be powered OFF if the device is installed
outdoors, or if the device is installed in a vehicle.
For product available in the USA/Canada market, only channel 1-11 can be
operated. Selection of other channels is not possible.
The device for the band 5150-5250 MHz is only for indoor usage to reduce
potential for harmful interference to co-channel mobile satellite systems.
INDUSTRY CANADA RADIATION EXPOSURE STATEMENT
This equipment complies with IC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance of 20 cm between the radiator and your body.
This device and its antennas(s) must not be co-located or operating in
conjunction with any other antenna or transmitter except in accordance with
IC multi-transmitter product procedures.
This radio transmitter (IC: 6921A-S7A741A, 5131A-LM940) has been approved by
Industry Canada to operate with the antenna types listed below with the
maximum permissible gain and required antenna impedance for each antenna
type indicated. Antenna types not included in this list, having a gain greater
than the maximum gain indicated for that type, are strictly prohibited for use
with this device.
Revision 2.1
RF Exposure Statement: To comply with RF Exposure requirements, this
equipment should be installed and operated with minimum distance of 45 cm
between the radiating device and your body.
ACCESSORIES IMPACTING COMPLIANCE
To maintain compliance with EMC, Radio, and RF Exposure requirements, use
only TRENDnet accessories intended for use with this product. All TRENDnet
accessories intended for use with this product will maintain EMC, Radio, and RF
20 December 2017
Document Part: 170738-001
Exposure compliance when installed according to instructions. Cellular
antennas must have a gain <3 dBi. 802.11 antennas must have a gain <5 dBi.
RECYCLING AND ENVIRONMENTAL INFORMATION
To find information on TRENDnet’s commitment to our environment and how to
responsibly recycle or recover TRENDnet products at the end of their useful
life, please visit TRENDnet.com/international.
SAFETY AND HAZARDS
This equipment is designed to operate in ambient temperatures up to 60 °C
(140 °F). When operating in elevated ambient temperatures, the surface of the
equipment may exceed 60 °C and become too hot to safely touch. Under this
condition, this product must be installed in a secured location that is not
accessible to accidental touch, and access to the device must be restricted to
service persons or users who possess the proper tool or key to access the device
and have been informed about the potential high surface temperatures and
instructed on how to safely handle and/or service the device.
AND/OR ITS AFFILIATES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES, AND EVEN IF SUCH DAMAGES ARE FORESEEABLE; OR (B) CLAIMS
BY ANY THIRD PARTY. NOTWITHSTANDING THE FOREGOING, IN NO EVENT
SHALL THE AGGREGATE LIABILITY OF TRENDNET AND/OR ITS AFFILIATES
ARISING UNDER OR IN CONNECTION WITH THE PRODUCT, REGARDLESS OF
THE NUMBER OF EVENTS, OCCURRENCES, OR CLAIMS GIVING RISE TO
LIABILITY, EXCEED THE PRICE PAID BY THE ORIGINAL PURCHASER OF THE
PRODUCT. THE LIMITATIONS OF LIABILITY SET FORTH HEREIN SHALL REMAIN IN
FULL FORCE AND EFFECT REGARDLESS OF WHETHER THE REMEDIES HEREUNDER
ARE DETERMINED TO HAVE FAILED OF THEIR ESSENTIAL PURPOSE.
PRIVACY
TRENDnet may collect general data pertaining to the use of TRENDnet products
via your Internet connection (wired and/or wireless) such as device ID/serial
number, network status, IP address, MAC address, operating system, browser
type and version number, etc., in order to provide you with better services,
enhance user experience, and improve performance.
OTHER BINDING DOCUMENTS; TRADEMARKS; COPYRIGHT
By activating or using your TEW-829DRU device, you agree to be bound by
TRENDnet’s Terms of Use, User License and other applicable Legal Policies.
© 2018 TRENDnet, Inc. All rights reserved. TRENDnet is not responsible for
omissions or errors in typography or photography. TRENDnet, TEW-829DRU, and
the TRENDnet logo are trademarks of TRENDnet, Inc. in the US and other
countries. Other trademarks are property of their respective owners.
Under no circumstances should the device be used in any areas
(a) where blasting is in progress,
(b) where explosive atmospheres may be present, or
(c) that are near (i) medical or life support equipment, or (ii) any equipment
which may be susceptible to any form of radio interference.
In such areas, the device MUST BE POWERED OFF AT ALL TIMES (since the
device otherwise could transmit signals that might interfere with such
equipment).
In addition, under no circumstances should the device be used in any aircraft,
regardless of whether the aircraft is on the ground or in flight. In any aircraft,
the device MUST BE POWERED OFF AT ALL TIMES since the device otherwise
could transmit signals that might interfere with various onboard systems on
such aircraft. Furthermore, under no circumstances should the device be used
by the driver or operator of any vehicle. Such use of the device will detract
from the driver’s or operator’s control of that vehicle. In some jurisdictions,
use of the device while driving or operating a vehicle constitutes a civil and/or
criminal offense.
Due to the nature of wireless communications, transmission and reception of
data by the device can never be guaranteed, and it is possible that data
communicated or transmitted wirelessly may be delayed, corrupted (i.e.,
contain errors), or totally lost. The device is not intended for, and TRENDnet
recommends the device not be used in any critical applications where failure to
transmit or receive data could result in property damage or loss or personal
injury of any kind (including death) to the user or to any other party.
TRENDnet expressly disclaims liability for damages of any kind resulting from:
(a) delays, errors, or losses of any data transmitted or received using the
device; or
(b) any failure of the device to transmit or receive such data.
For proper and safe vehicle installations, the GPIO accessory cable must be
connected to a fused circuit in the vehicle. This fused circuit requires a 3A
fuse. If the supply connection is made directly to the battery, the fuse should
be installed in the positive lead. For North America, a UL Listed fuse is to be
used.
Warning: This product is only to be installed by qualified personnel.
Purchaser agrees to indemnify TRENDnet against any liability or damages
caused to third parties as a result of Purchaser’s misuse or misapplication of
the TRENDnet product.
OPEN SOURCE SOFTWARE
This product contains software distributed under one or more of the following
open source licenses: GNU General Public License Version 2, BSD License, NetSNMP License, and PSF License Agreement for Python 3.3. For more information
on this software, including licensing terms and your rights to access source
code, contact TRENDnet at TRENDnet.com/opensource.
WARRANTY INFORMATION
TRENDnet, Inc. warrants this hardware product against defects in materials and
workmanship to the original purchaser for a period of three (3) years from the
date of shipment. This warranty is limited to a repair or replacement of the
hardware product, at TRENDnet’s discretion, as purchaser’s sole and exclusive
remedy. If this hardware product was procured as a component of a NetCloud
Solution Package, additional warranty may be available. Please see
TRENDnet’s website for details. TRENDnet does not warrant that the operation
of the product will meet your requirements or be error free. TRENDNET MAKES
NO OTHER WARRANTY, EITHER EXPRESSED OR IMPLIED, WITH RESPECT TO
THIS HARDWARE PRODUCT. TRENDNET SPECIFICALLY DISCLAIMS THE IMPLIED
WARRANTIES OR CONDITIONS OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, TITLE OR NON-INFRINGEMENT.
LIMITATION OF TRENDNET LIABILITY
The information contained in this Safety, Regulatory, and Warranty Guide is
subject to change without notice and does not represent any commitment
on the part of TRENDnet or its affiliates. TRENDNET AND ITS AFFILIATES
HEREBY SPECIFICALLY DISCLAIM LIABILITY FOR ANY AND ALL: (A) DIRECT,
INDIRECT, SPECIAL, GENERAL, INCIDENTAL, CONSEQUENTIAL, PUNITIVE OR
EXEMPLARY DAMAGES, INCLUDING WITHOUT LIMITATION FOR LOSS OF
PROFITS OR REVENUE OR OF ANTICIPATED PROFITS OR REVENUE ARISING
OUT OF THE USE OR INABILITY TO USE THE PRODUCT, EVEN IF TRENDNET
Revision 2.1
20 December 2017
Document Part: 170738-001

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.7
Linearized                      : No
Author                          : David Heald
Create Date                     : 2018:02:22 17:40:58+08:00
Modify Date                     : 2018:02:22 18:17:29+08:00
Language                        : zh-TW
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30
Producer                        : Microsoft® Word 2016
Format                          : application/pdf
Creator                         : David Heald
Creator Tool                    : Microsoft® Word 2016
Metadata Date                   : 2018:02:22 18:17:29+08:00
Document ID                     : uuid:B338C408-091D-4D12-973C-6B55D00D45B1
Instance ID                     : uuid:d0cb20ea-01aa-4af1-be8b-38025a6d28b9
Page Count                      : 2

EXIF Metadata provided by EXIF.tools