TSC Auto ID Technology RFBHS BT module User Manual 1 Introduction

Download:
Mirror Download [FCC.gov]
Document ID	2523054
Application ID	kJ1Ctw6iBCzjMKQqbJQbjA==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.07kB (163356 bits)
Date Submitted	2015-02-04 00:00:00
Date Available	2015-02-05 00:00:00
Creation Date	2017-10-19 01:01:12
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-19 01:01:12
Document Title	1. Introduction
Document Creator	Acrobat PDFMaker 11 Word 版
Document Author:	camille

RF-BHS
Bluetooth(BT) 3.0/4.0+EDR module
USER’S
MANUAL
Copyright Information
©2014 TSC Auto ID Technology Co., Ltd,
The copyright in this manual, the software and firmware in the printer described therein are
owned by TSC Auto ID Technology Co., Ltd, All rights reserved.
Information in this document is subject to change without notice and does not represent
a commitment on the part of TSC Auto ID Technology Co. No part of this manual may be
reproduced or transmitted in any form or by any means, for any purpose other than the
purchaser’s personal use, without the expressed written permission of TSC Auto ID
Technology Co.
Agency Compliance and Approvals
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may cause
undesired operation.
IMPORTANT NOTE:
FCC Radiation Exposure Statement:
The product comply with the US portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this manual. The
further RF exposure reduction can be achieved if the product can be kept as far as possible
from the user body or set the device to lower output power if such function is available.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna,
As long as 1 condition above is met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed
IMPORTANT NOTE
In the event that these conditions can not be met (for example certain laptop configurations
or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains FCC ID:
VTV-RFBHS”.
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Industry Canada statement:
This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the
following two conditions:
(1) This device may not cause interference; and (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
Cet appareil est conforme aux CNR exemptes de licence d'Industrie Canada. Son
fonctionnement est soumis aux deux conditions suivantes:
(1) Ce dispositif ne peut causer d'interférences; et(2) Ce dispositif doit accepter toute
interférence, y compris les interférences qui peuvent causer un mauvais fonctionnement de
l'appareil.
Radiation Exposure Statement:
The product comply with the Canada portable RF exposure limit set forth for an
uncontrolled environment and are safe for intended operation as described in this manual. The
further RF exposure reduction can be achieved if the product can be kept as far as possible
from the user body or set the device to lower output power if such function is available.
Déclaration d'exposition aux radiations:
Le produit est conforme aux limites d'exposition pour les appareils portables RF pour les
Etats-Unis et le Canada établies pour un environnement non contrôlé. Le produit est sûr pour
un fonctionnement tel que décrit dans ce manuel. La réduction aux expositions RF peut être
augmentée si l'appareil peut être conservé aussi loin que possible du corps de l'utilisateur ou
que le dispositif est réglé sur la puissance de sortie la plus faible si une telle fonction est
disponible.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna.
As long as 1 condition above are met, further transmitter test will not be required. However, the
OEM integrator is still responsible for testing their end-product for any additional compliance
requirements required with this module installed.
Cet appareil est conçu uniquement pour les intégrateurs OEM dans les conditions suivantes:
1) Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.
Tant que les 1 condition ci-dessus sont remplies, des essais supplémentaires sur l'émetteur ne
seront pas nécessaires. Toutefois, l'intégrateur OEM est toujours responsable des essais sur
son produit final pour toutes exigences de conformité supplémentaires requis pour ce module
installé.
IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations
or co-location with another transmitter), then the Canada authorization is no
longer considered valid and the IC ID can not be used on the final product. In
these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization.
NOTE IMPORTANTE:
Dans le cas où ces conditions ne peuvent être satisfaites (par exemple
pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un
autre émetteur), l'autorisation du Canada n'est plus considéré comme valide et l'ID IC ne peut
pas être utilisé sur le produit final. Dans ces circonstances, l'intégrateur OEM sera chargé de
réévaluer le produit final (y compris l'émetteur) et l'obtention d'une autorisation distincte au
Canada.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains
IC:10524A-RFBHS”.
Plaque signalétique du produit final
Le produit final doit être étiqueté dans un endroit visible avec l'inscription suivante: "Contient
des IC: 10524A-RFBHS".
Manual Information to the End User
The OEM integrator has to be aware not to provide information to the end user regarding how
to install or remove this RF module in the user’s manual of the end product which integrates
this module.
The end user manual shall include all required regulatory information/warning as show in this
manual.
Manuel d'information à l'utilisateur final
L'intégrateur OEM doit être conscient de ne pas fournir des informations à l'utilisateur final
quant à la façon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du
produit final qui intègre ce module.
Le manuel de l'utilisateur final doit inclure toutes les informations réglementaires requises et
avertissements comme indiqué dans ce manuel.
This radio transmitter (IC: 10524A-RFBHS) has been approved by Industry Canada to operate
with the antenna types listed below with the maximum permissible gain indicated. Antenna
types not included in this list, having a gain greater than the maximum gain indicated for that
type, are strictly prohibited for use with this device
Cet émetteur radio (IC: 10524A-RFBHS) a été approuvé par Industrie Canada pour
fonctionner avec les types d'antenne énumérés ci-dessous avec le gain maximal admissible
indiqué. Types d'antennes ne figurent pas dans cette liste, ayant un gain supérieur au gain
maximum indiqué pour ce type, sont strictement interdits pour une utilisation avec cet appareil
Type
Connector
Gain
UFL
1 dBi
Chip
1. Introduction
Part Name: RF-BHS < ISSC BM77SPP03MC2 Bluetooth module>
Part Number: BM77SPP03MC2-xxxxxx
The ISSC BM77SPP03MC2 Bluetooth module is design for Bluetooth standard SPP/ BLE electronic accessories
via Bluetooth connectivity. It is available in the 2.4GHz ISM band Class 2 Radio, compatible with Bluetooth Core
Specification Version 3.0/ 4.0 + EDR.
ISSC IS1677NM single chip solution combines transceiver and baseband function to decrease the
external components. It narrows down the module size and minimizes its cost.
The optimized power design minimize power consumption to keep low battery
1.1. Major Components
- ISSC IS1677NM (40 pin QFN, single-chip Bluetooth transceiver and baseband processor)
- Serial EEPROM 8K (1024*8) TSSOP 8P
1.2. Features
- Bluetooth 3.0/ 4.0+ EDR compliant
- Low power 1.8V RF operation
- RF transmitter output power Class 2
- RF receiver GFSK typical -90dBm, π/4 PSK typical -90dBm, 8DPSK typical -83dBm, BLE typical -92dBm
- Internal ROM and 4Mibts of flash
- I2C for external EEPROM
- 1 LED driver
1.3. Application
- GPS
- Printers
- Electric Scale
- Blood Pressure Monitors
- Bar code Scanner
- Industrial Applications (CNC, PLC, RFID)
2. Product Image
3. Connector Schematic
Revise History
Date
Content
Editor
TSC Auto ID Technology Co., Ltd.
Corporate Headquarters
9F., No.95, Minquan Rd., Xindian Dist.,
New Taipei City 23141, Taiwan (R.O.C.)
TEL: +886-2-2218-6789
FAX: +886-2-2218-5678
Web site: www.tscprinters.com
Li Ze Plant
No.35, Sec. 2, Ligong 1st Rd., Wujie Township,
Yilan County 26841, Taiwan (R.O.C.)
TEL: +886-3-990-6677
FAX: +886-3-990-5577

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract
Author                          : camille
Create Date                     : 2015:02:03 10:11:16+08:00
Modify Date                     : 2015:02:03 10:11:46+08:00
Subject                         : 1.1 Product Introduction
Tag LCID                        : 1028
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 5.4-c005 78.147326, 2012/08/23-13:03:03
Metadata Date                   : 2015:02:03 10:11:46+08:00
Creator Tool                    : Acrobat PDFMaker 11 Word 版
Document ID                     : uuid:88b149ed-987c-491c-800c-f65c8699b926
Instance ID                     : uuid:945d7cbb-f220-4305-a33e-2fce03deee2b
Format                          : application/pdf
Title                           : 1..Introduction
Description                     : 1.1 Product Introduction
Creator                         : camille
Producer                        : Adobe PDF Library 11.0
Source Modified                 : D:20150203021109
Company                         : quietek
Lcid                            : 1028
Tag Version                     : 0809
Headline                        : 1.1 Product Introduction
Page Layout                     : OneColumn
Page Count                      : 11

EXIF Metadata provided by EXIF.tools