TSC Auto ID Technology T083RFBHS Barcode Printer User Manual
TSC Auto ID Technology Co., Ltd. Barcode Printer
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 4166876 |
| Application ID | ufWa8XH+qc6GO10LFglgLQ== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 210.62kB (2632700 bits) |
| Date Submitted | 2019-02-14 00:00:00 |
| Date Available | 2019-02-14 00:00:00 |
| Creation Date | 2019-01-22 09:24:52 |
| Producing Software | Microsoft® Word 2013 |
| Document Lastmod | 2019-01-25 09:11:18 |
| Document Title | User Manual |
| Document Creator | Microsoft® Word 2013 |
TDM-30 Series Direct Thermal Portable Printer USER’S MANUAL Copyright Information © 2019 TSC Auto ID Technology Co., Ltd, The copyright in this manual, the software and firmware in the printer described therein are owned by TSC Auto ID Technology Co., Ltd, All rights reserved. CG Triumvirate is a trademark of Agfa Corporation. CG Triumvirate Bold Condensed font is under license from the Monotype Corporation. Windows is a registered trademark of Microsoft Corporation. All other trademarks are the property of their respective owners. Information in this document is subject to change without notice and does not represent a commitment on the part of TSC Auto ID Technology Co. No part of this manual may be reproduced or transmitted in any form or by any means, for any purpose other than the purchaser’s personal use, without the expressed written permission of TSC Auto ID Technology Co., Ltd, ii Agency Compliance and Approvals 2014/30/EU(EMC), 2014/35/EU(LVD), EN 55032 Class B EN 55024 EN61000-3-2:2014 EN61000-3-3:2013 EN 60950-1 2011/65/EU(RoHS 2.0) FCC part 15B, Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/ TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This Class B digital apparatus complies with Canadian ICES-003 Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. AS/NZS CISPR 22 Class B AS/NZS CISPR 32 Class B NOM-019-SCFI-1998 10 C.F.R. Section 430.23(aa) (Appendix Y to Subpart B of part 430) TP TC 004/2011 TP TC 020/2011 LP0002 iii GB 4943.1 GB/T9254 GB 17625.1 IS 13252(Part 1)/ IEC 60950-1 CNS 13438 CNS 14336-1 CNS 15663 KN 32 / KN 35 Important safety instructions: 1. Read all of these instructions and keep them for later use. 2. Follow all warnings and instructions on the product. 3. Disconnect the power plug from the AC outlet before cleaning or if fault happened. Do not use liquid or aerosol cleaners. Using a damp cloth is suitable for cleaning. 4. The mains socket shall be installed near the equipment and easily accessible. 5. The unit must be protected against moisture. 6. Ensure the stability when installing the device, Tipping or dropping could cause damage. 7. Make sure to follow the correct power rating and power type indicated on marking label provided by manufacture. 8. Please refer to user manual for maximum operation ambient temperature. 重要安全說明： 1. 閱讀所有這些說明，並保留以備未來使用。 2. 按照產品上的所有警告和說明進行操作。 3. 在清潔前或發生故障時，拔除電源插頭與交流電源插座的連接。 不要使用液體或噴霧清潔劑。建議使用濕布清潔。 4. 電源插座應安裝在設備附近及方便使用處。 5. 本機器必須防止潮濕。 6. 確保安裝設備時的穩定性，翻倒或跌落可能會導致設備損壞。 7. 確保按照製造商提供的標籤上標明之正確的額定功率和電源類型進行設定。 8. 請參考使用手冊以確認環境溫度的最大值。 WARNING: Hazardous moving parts, keep fingers and other body parts away. iv CAUTION: (For equipment with RTC (CR2032) battery or rechargeable battery pack) Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the Instructions as below. 1. DO NOT throw the battery in fire. 2. DO NOT short circuit the contacts. 3. DO NOT disassemble the battery. 4. DO NOT throw the battery in municipal waste. 5. The symbol of the crossed out wheeled bin indicates that the battery should not be placed in municipal waste. 警告： （對於帶有 RTC（CR2032）電池或可充電電池組的設備） 如果更換不正確的電池類型，會有爆炸的危險。 請按照以下說明處理廢電池： 1. 請勿將電池投入火中。 2. 請勿使觸點短路。 3. 請勿拆卸電池。 4. 請勿將電池丟入都市廢棄物。 5. 垃圾桶畫叉圖案表示電池不應放置在都市廢棄物中。 Caution: The printhead may be hot and could cause severe burns. Allow the printhead to cool. CAUTION: Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. CE Statement: This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator & your body. RF exposure warning (For Bluetooth) (FCC ID:VTV-T083RFBHS) The equipment complies with FCC RF exposure limits set forth for an uncontrolled environment. The equipment must not be co-located or operating in conjunction with any other antenna or transmitter. Canada, Industry Canada (IC) Notices This Class B digital apparatus complies with Canadian ICES-003 and RSS-210. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Radio Frequency (RF) Exposure Information The radiated output power of the Wireless Device is below the Industry Canada (IC) radio frequency exposure limits. The Wireless Device should be used in such a manner such that the potential for human contact during normal operation is minimized. This device has also been evaluated and shown compliant with the IC RF Exposure limits under portable exposure conditions. (Antennas are less than 20 cm of a person's body). (For Bluetooth) Canada, avis de l'Industry Canada (IC) (IC:10524A-T083RFBHS) Cet appareil numérique de classe B est conforme aux normes canadiennes ICES-003 et RSS-210. Son fonctionnement est soumis aux deux conditions suivantes : (1) cet appareil ne doit pas causer d'interférence et (2) cet appareil doit accepter toute interférence, notamment les interférences qui peuvent affecter son fonctionnement. Informations concernant l'exposition aux fréquences radio (RF) La puissance de sortie émise par l’appareil sans fil est inférieure à la limite d'exposition aux fréquences radio de l'Industry Canada (IC). Utilisez l’appareil sans fil de façon à minimiser les contacts humains lors du fonctionnement normal. Ce périphérique a également été évalué et démontré conforme aux limites d'exposition radio-fréquence par l'IC pour des utilisations par des opérateurs mobiles (les antennes sont à moins de 20 cm du corps d'une personne). (Pour le Bluetooth) FCC 15.21 Information to user. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. vi NCC 警語: 經型式認證合格之低功率射頻電機，非經許可，公司、商號或使用者均不得擅自變更頻 率、加大功率或變更原設計之特性及功能。(即低功率電波輻射性電機管理辦法第十二 條) 低功率射頻電機之使用不得影響飛航安全及干擾合法通信；經發現有干擾現象時，應立 即停用，並改善至無干擾時方得繼續使用。 前項合法通信，指依電信法規定作業之無線電通信。低功率射頻電機須忍受合法通信或 工業、科學及醫療用電波輻射性電機設備之干擾。(即低功率電波輻射性電機管理辦法 第十四條) 警告： 本電池如果更換不正確會有爆炸的危險，請依製造商說明書處理用過之電池。 vii 限用物質及其化學符號 Restricted substances and its chemical symbols 六價鉻 單元Unit 鉛Lead 汞Mercury 鎘Cadmium (Pb) (Hg) (Cd) 內外鐵件 滾輪 銘版 電路板 晶片電阻 積層陶瓷表面 黏著電容 集成電路-IC 電源供應器 印字頭 馬達 液晶顯示器 插座 多溴二苯醚 Hexavalent Polybrominate Polybrominate chromium d biphenyls d diphenyl (Cr ) (PBB) ethers (PBDE) +6 內外塑膠件 多溴聯苯 ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ 線材 備考 1.〝超出 0.1 wt %〞及〝超出 0.01 wt %〞係指限用物質之百分比含量超出百分比含量基準值。 Note 1：“Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicate that the percentage content of the restricted substance exceeds the reference percentage value of presence condition. 備考 2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。 Note 2：“○” indicates that the percentage content of the restricted substance does not exceed the percentage of reference value of presence. 備考 3.〝－〞係指該項限用物質為排除項目。 Note 3：The “−” indicates that the restricted substance corresponds to the exemption. viii Contents 1. Introduction....................................................................................................... 1 1.1 Product Introduction........................................................................................ 1 1.2 Product Features ............................................................................................. 2 1.2.1 Printer Standard Features ................................................................. 2 1.2.2 Printer Optional Features .................................................................. 3 1.3 General Specifications .................................................................................... 4 1.4 Print Specifications ......................................................................................... 5 1.5 Media Specifications ....................................................................................... 5 2. Operations Overview ........................................................................................ 7 2.1 Unpacking and Inspection ............................................................................... 7 2.2 Printer Overview .............................................................................................. 8 2.2.1 Front View .......................................................................................... 8 2.2.2 Interior View ..................................................................................... 10 2.2.3 Rear View ......................................................................................... 11 2.3 Operator control ............................................................................................ 12 2.3.1 LED Indication, LCD screen, and Keys ........................................... 12 3. Setup ............................................................................................................... 15 3.1 Install the Battery ........................................................................................... 15 3.2 Charge the Battery ......................................................................................... 16 3.2.1 Charge the Battery ........................................................................... 16 3.2.2 Charge by Charger Station (Optional) ............................................. 18 3.3 Communicate ................................................................................................. 20 3.3.1 Connecting with the Communication Cable ................................... 20 3.3.2 Connecting with Bluetooth (Optional) .......................................... 20 3.4 Loading the Media ......................................................................................... 21 4. Accessories ..................................................................................................... 22 4.1 Install the Belt Clip......................................................................................... 22 4.2 Install the IP54-rated environmental case with shoulder strap (Optional) ... 23 5. Power-on Utilities............................................................................................ 25 5.1 Media Sensor Calibration .............................................................................. 25 5.2 Self-test and Dump Mode .............................................................................. 26 5.3 Printer Initialization ....................................................................................... 29 6. Diagnostic Tool ............................................................................................... 30 6.1 Start the Diagnostic Tool .............................................................................. 30 6.2 Printer Function ............................................................................................ 31 ix 6.3 Calibrating Media Sensor by Diagnostic Tool .............................................. 32 6.3.1 Auto Calibration ............................................................................... 32 6.4 Setting Bluetooth by Diagnostic Tool (Optional) ......................................... 33 7. Troubleshooting ............................................................................................. 34 7.1 Common Problems ........................................................................................ 34 8. Maintenance .................................................................................................... 36 Revise History ..................................................................................................... 37 1. Introduction 1.1 Product Introduction Thank you very much for purchasing TSC bar code printer. Enjoy TSC’s reputation for cost-efficient, high durability printers with the TDM-30 mobile barcode printer. The TDM-30 is a comfortable, light-weight printer capable of working with any mobile printing application where you need quick, simple receipts/labels on demand. Our TDM-30 is designed for a rough life, inside the IP54-rated environmental case to resist dust and water and with its durable design prepared to take up to 2.1 meters fall and keep printing. These small and light printers can be worn comfortably for a full shift, without interfering with the user’s tasks. Use USB, optional Bluetooth to connect to a mobile computer or even a smartphone and produce clear easy-to-read receipts hour after hour. This document provides an easy reference for operating the TDM-30. The online version of the Programmer's manual, or more information can be downloaded from our official website. To print label formats, please refer to the instructions provided with your labeling software; if you need to write the custom programs, please refer to the TSPL/TSPL2 programming manual that can be found on the accessories or at TSC official website. − Applications Direct store deliveries (DSD) Proof of Delivery and Pickup Field Sales/Repairs Mobile Point-of-Sale Parking Citations Mobile Ticketing Onboard Transportation Ticketing Utility Billing/Meter Reading Fleet Management 1.2 Product Features 1.2.1 Printer Standard Features The printer offers the following standard features. Product standard feature Direct thermal printing Black mark reflective sensor Gap reflective sensor Head open sensor 3 operation buttons (On/off, feed/pause, and cover-open buttons) LED version: 5 LEDs: 1 for printer states; 3 for Battery capacity; 1 for RF status LCD version: LCD color display: showing battery status, media type, firmware version, and error messages 1 LED for Printer Status 1 LED for RF connection (3 colors) Audible alert Programmable buzzer Rechargeable Li-ion battery Micro USB 2.0 (High speed mode) interface 32 MB DRAM 16 MB NOR Flash memory 32-bit RISC high performance processor Eltron® EPL, Epson® ESC-POS, and Zebra® ZPL emulation languages support Fonts and bar codes can be printed in any one of the four directions (0, 90,180, 270 degree) 8 alpha-numeric bitmap fonts One Monotype Imaging® CG Triumvirate Bold Condensed scalable font Built-in Monotype True Type Font engine Downloadable fonts from PC to printer memory Downloadable firmware upgrades Support TPH Care function Text, bar code, graphics/image printing (Please refer to the TSPL/TSPL2 programming manual for supporting code page) Supported bar code 1D bar code Code128 subsets A.B.C,Code128UCC, EAN128, Interleave 2 of 5,Code 39,Code 93, EAN-13, EAN-8, Supported image 2D bar code CODABLOCK mode, DataMatrix, Maxicode, PDF-417, Aztec, MicroPDF417, QR code, RSS Barcode (GS1 Databar) BITMAP, BMP, PCX (Max. 256 colors graphics) Codabar, POSTNET, UPC-A, UPC-E, EAN and UPC 2(5) digits add-on, MSI, PLESSEY, China Post, ITF14, EAN14, Code 11, TELPEN, PLANET, Code 49, Deutsche Post Identcode, Deutsche Post Leitcode, LOGMARS 1.2.2 Printer Optional Features The printer offers the following optional features. Product option feature User Factory options options Micro USB 2.0 (high-speed mode) + MFi Bluetooth V4.2 ○ NFC tag ○ TSPL-EZD and TSPL-EZ with CPCL or ESC-POS emulation ○ 1-bay printer wireless charging station ○ 4-bay printer wireless charging station ○ 1-bay printer charger station ○ 4-bay printer charger station ○ 1-bay battery charger station ○ 4-bay battery charger station ○ 12-60V DC automobile cigarette lighter plug ○ Vehicle Charger ○ Vehicle Charger Converter IP54-rated protective case with shoulder strap ○ Micro USB 2.0 cable (1.5M) ○ 10.8-60 VDC power source with dummy battery ○ Rechargeable Li-ion battery ○ Smart battery pack ○ External charging pin (for wireless charging cover ○ and cradle only) 3” paper core adapter ○ ○ Linerless mode ○ CD 1.3 General Specifications General Specifications Physical dimensions 105 mm (W) x 49.5 mm (H) x 116 mm (D) Enclosure Plastic Weight (w/ battery) 385g Electrical Internal charging capability (battery-in) Input: AC 100-240V, 2.5A, 50-60Hz Output: DC 12V/ 1A 12-24V DC automobile cigarette lighter plug Auto-switching AC adapter External charging capability (battery-out) Single printer charger station Input: 12V/ 2A Output: 12V/ 2A 4-bay printers charger station Input: 12V/ 5A Output:12V/ 5A 1 bay battery charger station - Input: 12V/ 2A - Output: 8.4V/ 1.5A 4 bay batteries charger station - Input: 24V/ 2.5A DC - Output: 8.4V/ 1.5A*4 DC Note: The printer will automatically turn off when stopping operation after 30 minutes. Environmental Operation Temperature: -15 ~ 50˚C (5 ~ 122˚F) condition Charging Temperature: 0 ~ 40˚C (32 ~ 104˚F) Storage Temperature: -30 ~ 70 ˚C (-22 ~ 158˚F) Relative Humidity: - Operation: 10% to 90% non-condensing - Storage: 10% to 90% non-condensing IP54 w/ protective case Drop 1.8m (5.9ft) w/o IP54-rated environmental case Drop 2.1m (6.9ft) w/ IP54-rated environmental case 1.4 Print Specifications Print Specifications TDM-30 Print head resolution 203 dots/inch (8 dots/mm) Printing method Direct thermal Dot size 0.125 x 0.125 mm(1 mm = 8 dots) (width x length) Print speed (inches per second) Max. 4 ips (102 mm/sec) Max. print width 72 mm (2.83") Continuous receipt paper: 2,794 mm (110”) Max. print length (associate with DRAM) Vertical: 1 mm max. Printout bias Horizontal: 1 mm max. 1.5 Media Specifications Media Specifications TDM-30 Media roll capacity Media type Max. O.D.: 40 mm Continuous, die-cut, receipt, liner free label, and black mark Media wound type Media length Media width Outside wound 10 mm (0.39”) ~ 2,794 mm (110”) Tear mode: 50 mm (1.97”) ~ max. print length Max. 80 mm (includes liner) Black mark label: min.8 mm (w) x 2 mm (h) Gap label: min.8 mm (w) x 2 mm (h) Media thickness 0.06mm ~ 0.16 mm In lowest print speed: 0.06mm ~0.18 mm Note: Please locate the black mark on the printing side when using black mark continuous label. 2. Operations Overview 2.1 Unpacking and Inspection This printer has been specially packaged to withstand damage during shipping. Please carefully inspect the packaging and printer upon receiving the bar code printer. Please retain the packaging materials in case you need to reship the printer. Unpacking the printer, the following items are included in the carton. One printer unit One Li-ion battery One quick installation guide One Auto-switching AC adapter One belt clip If any parts are missing, please contact the Customer Service Department of your purchased reseller or distributor. 2.2 Printer Overview 2.2.1 Front View For LED version 1. Power on/off button 2. Feed/stop button 3. LED indicators 4. Media cover 5. Media cover window 6. Media cover release button For LCD version 1. Power on/off button 2. Feed/stop button 3. LED indicators & LCD screen 4. Media cover 5. Media cover window 6. Media cover release button 2.2.2 Interior View 1. Tear edge 2. Print head 3. Platen roller 4. Black mark sensor 10 2.2.3 Rear View 1. Li-ion Battery 2. Battery open clasp 3. Interface cover 4. Power jack 5. USB interface 11 2.3 Operator control 2.3.1 LED Indication, LCD screen, and Keys For LED version 1. Power on/off button 2. Feed/Pause button 3. Printer status LED indicator 4. Battery charge level LED indicators 5. Wireless status LED indicator 12 For LCD version 1. Power on/off button 2. Feed/Pause button 3. Printer status/Wireless status LED indicator 4. LCD screen (indicates battery status/media type/firmware version/error messages) Keys Function 1. Press and hold for 2-3 seconds to turn on the printer. 2. Press and hold for 2-3 seconds to turn off the printer. 1. Ready status: Feed one label 2. Printing status: Pause the print job 13 LED Status Indication Off Printer is ready Green (blinking) Printer is paused Sleep mode/ entered the sleep mode after stop Printer status LED indicator working over 2 minutes Green (blinking every two seconds) (The interval can be changed by revising the command, refer to TSPL/TSPL2 programming manual on TSC website). Red (solid) Media cover is open Red (blinking) Printer error Green (blinking) Recharge the battery Amber (solid) Battery is charging Battery status LED Fully charged indicator Green 2/3 charged level (solid) 1/3 charged level Wireless/Bluetooth Blue (solid) status LED indicator Bluetooth device is ready Bluetooth Blue (blinking) 14 Bluetooth device is communicating 3. Setup 3.1 Install the Battery 1. Insert battery to the left side of battery slot on the rear of the printer. PUSH 2. Push the right side of the battery down. 3. Pull the battery clasp to lock the battery. Battery safety warning: DO NOT throw the battery in fire. DO NOT short circuit the contacts. DO NOT disassemble the battery. DO NOT throw the battery in municipal waste. The symbol of the crossed out wheeled bin ( be placed in municipal waste. 15 ) indicates that the battery should not 3.2 Charge the Battery It takes 1.5 to 2 hours to fully charge the battery before the first time usage. The lifetime of the battery is 300 times for charge/discharge cycles. 3.2.1 Charge the Battery 1. Open the interface cover and plug the power cord in to the power jack. Note: Please switch OFF printer power prior to plug in the power cord to printer power jack. When the battery is charging, please do not remove the battery from the printer, otherwise, please re-plug the power cord into a power outlet. 2. Plug the power cord into a properly power outlet. 3. When the battery installed on printer and start charging, the printer will automatically open and color of battery status LED indicator is solid amber. The amber LED indicator will turned off after the battery is fully charged. Battery charging Battery fully charged Auto power off Note: 1. When printer start charging, the printer will automatically open and could not turn-off the power. 2. When checking the battery status, please connect the adapter to printer, the LED indicator will turn to green then extinguished when the battery is fully charged. 16 Charging Temperature The battery normal working condition is from 0°C to 40°C (32 °F to 104 °F). The device or battery charger always perform battery charging in a safe and optimum manner. At higher temperatures (e.g. approximately +40 °C (+104 °F) or charging when turning on the printers), the printer or battery charger may stop charging for a period of time to keep the battery at acceptable temperatures. 17 3.2.2 Charge by Charger Station (Optional) 1. Plug the power cord to the power jack on the charger station. 2. Insert the battery along the slot to the right side of charger station as pictured. (Refer to section 3.1 for battery installation procedure.) 3. Push the battery clasp and properly install the battery, it will start charging. Note: The battery is completely charged and the amber of LED indicator will be off and turns to green. 18 Note: The four bay batteries charger station is also available for your reference. LED Color Green / Solid Green / Blinking Red / Blinking Off Description Battery is completely charged Battery is charging Battery charging error No battery Battery is completely charged over 1.5 ~ 2 hrs. 19 3.3 Communicate 3.3.1 Connecting with the Communication Cable USB to USB Cable (Optional) 1. Open the interface cover and connect the printer to the computer with USB cable. USB interface USB connector (Printer) USB connector (PC) 3.3.2 Connecting with Bluetooth (Optional) Turn on the printer and make sure the Bluetooth of device is opened. Default Name RF-BHS PIN 0000 Note: Please refer to section 6.5 to change the name of default and PIN. 20 3.4 Loading the Media 1. Open the printer media cover by pressing the media cover release button. 2. Place the media roll at the correct side, and pull out enough paper over the tear edge. 3. Press the media cover on both sides to close it and make sure the media cover have closed correctly. 21 4. Accessories 4.1 Install the Belt Clip 1. Turn the battery to rear side, remove the battery on the rear of the printer and lock the belt clip on the hole above the battery. 2. Press the ball on the belt clip to the hole as pictured. 3. After reinstalled the battery, the printer can be hung on the belt. 22 4.2 Install the IP54-rated environmental case with shoulder strap (Optional) 1. Open the zip along the arrow direction indicated on case cover. Zip of case cover 2. Place the printer in the case. Note: The printing side must face the outside cover as indicated. 23 3. Zip up the case cover. The outside cover should be opened and fixed while printing. Outside cover 24 Outside cover fixed 5. Power-on Utilities There are three power-on utilities to set up and test printer hardware. These utilities are activated by pressing FEED button ( ) then turning on the printer power simultaneously and release the button at different positions of LED indicator. Please follow the steps below for different power-on utilities. 1. Turn off the printer power switch. 2. Hold on the FEED button ( ) then turn on the power switch ( ). 3. Release the button ( ) when LED indicates with different positions for different functions. The positions of LED light will be changed as following pattern: Power on utilities LED Functions (solid) 1. Media sensor calibration (5 blinks) (5 blinks) (5 blinks) (Solid green) Release 2. Self-test and enter dump Release mode 3. Printer initialization Release 5.1 Media Sensor Calibration Please follow the steps below to calibrate the media sensor. 1. Turn off the power switch. 2. Hold on the FEED button ( ) then turn on the power switch. 3. Release the FEED button ( ) when the indicator becomes and blinking. (Any green will do during the 5 blinks) It will calibrate the black mark sensor sensitivity. The LEDs will be changed as following order: (amber) (5 blinks) (5 blinks) (solid green) 25 (5 blinks) 5.2 Self-test and Dump Mode Please follow the steps below. 1. Turn off the power switch. 2. Hold on the FEED button ( ) then turn on the power switch. 3. Release the FEED button ( ) when the indicator becomes and blinking. (Any green will do during the 5 blinks) The LEDs will be changed as following order: (amber) (5 blinks) (5 blinks) (solid green) (5 blinks) 4. It calibrates the sensor and measures the media length and prints internal settings then enter the dump mode. 5. Turn off / on the power to resume printer for normal printing. 26 Self-test Printer will print the printer configuration after media sensor calibration. Self-test printout can be used to check if there is any dot damage on the heater element, printer configurations and available memory space. Self-test printout Model name F/W version Firmware checksum Printer S/N TSC configuration file System date System time Printed mileage (meter) Cutting counter Print speed (inch/sec) Print darkness Label size (inch) Gap distance (inch) Gap/black mark sensor intension Code page Country code ZPL setting information Print darkness Print speed (inch/sec) Label size Control prefix Format prefix Delimiter prefix Printer power up motion Printer head close motion Note: ZPL is emulating for Zebra® language. RS232 serial port configuration 27 Numbers of download files Total & available memory space Print head check pattern Dump mode Printer will enter dump mode after printing printer configuration. In the dump mode, all characters will be printed in 2 columns as following. The left side characters are received from your system and right side data are the corresponding hexadecimal value of the characters. It allows users or engineers to verify and debug the program. Hex decimal data related to left ASCII Data column of ASCII data Note: 1. Dump mode requires 2” wide paper width. 2. Turn off / on the power to resume printer for normal printing. 28 5.3 Printer Initialization Printer initialization is used to clear DRAM and restore printer settings to defaults. Printer initialization is activated by the following procedures. 1. Turn off the power switch. 2. Hold on the FEED button then turn on the power switch. 3. Release the FEED button when the indicator becomes and blinking. (Any green will do during the 5 blinks). The LEDs will be changed as following order: (amber) (5 blinks) (5 blinks) (solid green) (5 blinks) Printer configuration will be restored to defaults as below after initialization. Parameter Default setting Speed 50.8 mm/sec (2 ips) Density Media Width 2.83” (72 mm) Media Height 4” (101.5 mm) Sensor Type Black mark sensor (As paper end sensor) Black Mark Setting As paper end sensor Print Direction Reference Point 0,0 (upper left corner) Offset Serial Port Settings 9600 bps, none parity, 8 data bits, 1 stop bit Code Page 850 Country Code 001 Clear Flash Memory No IP Address DHCP 29 6. Diagnostic Tool TSC’s Diagnostic Utility is an integrated tool incorporating features that enable you to explore a printer’s settings/status; change a printer’s settings; download graphics, fonts and firmware; create a printer bitmap font; and send additional commands to a printer. With the aid of this powerful tool, you can review printer status and settings in an instant, which makes it much easier to troubleshoot problems and other issues. 6.1 Start the Diagnostic Tool 1. Double click on the Diagnostic tool icon to start the software. 2. There are four features (Printer Configuration, File Manager, Bitmap Font Manager, Command Tool) included in the Diagnostic utility. Features tab Interface Printer functions Printer setup Printer Status 30 6.2 Printer Function 1. Select the PC interface connected with bar code printer. The default interface setting is USB interface. If USB interface is connected with printer, no other settings need to be changed in the interface field. 2. Click the “Printer Function” button to setup. 3. The detail functions in the Printer Function Group are listed as below. Function Description Calibrate the sensor specified in the Printer Setup group media sensor field Setup the IP address, subnet mask, gateway for the on board Ethernet Calibrate Sensor Ethernet Setup RTC Setup Synchronize printer Real Time Clock with PC Factory Default Initialize the printer and restore the settings to factory default. (Please refer section 5.3) Reset Printer Reboot printer Print Test Page Print a test page Configuration Page Print printer configuration (Please refer section 5.2) Dump Text To activate the printer dump mode. Ignore AUTO.BAS Ignore the downloaded AUTO.BAS program Exit Line Mode Exit line mode. Password Setup Set the password to protect the settings For more information about Diagnostic Tool, please refer to the diagnostic utility quick start guide on TSC website at Downloads \ Manuals \ Utilities \ Diagnostic utility quick start guide. Note: The three different print modes below are available, you can download the command on TSPL/TSPL2 programming manual at TSC official website: Print modes DRAFT High print speed with lower density. OPTIMUM According to the label content such as barcode, text, and graphic to lower the print speed for getting higher print quality. STANDARD (default) Standard print speed and quality. 31 6.3 Calibrating Media Sensor by Diagnostic Tool 6.3.1 Auto Calibration 1. Make sure the media is already installed and media cover is closed. (Please refer to section 3.4) 2. Turn on the printer power switch. 3. Open Diagnostic tool and set interface. (The default setting is USB) The default interface setting is USB interface. If USB interface is connected with printer, no other settings need to be changed in the interface field. 4. Click the “Calibrate Sensor” button. 5. Select the media type and click the “Calibrate” button. Note: The TDM-30 can only support continuous, die-cut, receipt, and black mark media type. 32 6.4 Setting Bluetooth by Diagnostic Tool (Optional) 1. Make sure the media is already installed and media cover is closed. (Please refer to section 3.4) 2. Turn on the printer power switch. 3. Open Diagnostic tool and set interface. (The default setting is USB) The default interface setting is USB interface. If USB interface is connected with printer, no other settings need to be changed in the interface field. 4. Select “Wireless” tab and “Built-in wireless module” item. 5. Enter the new BT Local Name or BT PIN Code in the editor. 6. Press “Set” button to set the new BT name or BT PIN code of the printer. 7. Press “Get” button to get back the settings. Make sure the Bluetooth module settings are set properly. Note: * The printer connects with the computer via USB cable, which is option. 33 7. Troubleshooting 7.1 Common Problems The following guide lists the most common problems that may be encountered when operating this bar code printer. If the printer still does not function after all suggested solutions have been invoked, please contact the Customer Service Department of your purchased reseller or distributor for assistance. Problem Power indicator does not illuminate - The printer status from DiagTool shows “Head Open”. - The printer status from DiagTool shows “Out of Paper”. Possible Cause * The battery is not properly installed. * The battery is dead. Recovery Procedure * Reinstall the battery. * Switch the printer on. * Charge the battery. * The printer carriage is open. * Please close the print carriage. * Running out of media roll. * The media is installed incorrectly. * Black mark sensor is not calibrated. * Supply a new media roll. * Please refer to the steps on section 3.4 to reinstall the media roll. * Calibrate the black mark sensor. * Black mark sensor is not set properly. * Calibrate the black mark sensor. - The printer status from * Make sure media size is set * Set media size correctly. DiagTool shows “Paper Jam”. properly. * Clean the printer mechanism. * Media may be stuck inside the printer mechanism. * Delete unused files in the FLASH/DRAM. * Run printer self-test and check the Memory full ( FLASH / DRAM ) * The space of FLASH/DRAM available memory space for DRAM or is full. FLASH. * Check the available memory space for DRAM or FLASH via DiagTool. Poor Print Quality * Media is loaded incorrectly * Dust or adhesive accumulation on the print head. * Print density is not set properly. * Print head element is damaged. 34 * Reload the supply. * Clean the print head. * Clean the platen roller. * Adjust the print density and print speed. * Run printer self-test and check the print head test pattern if there is dot missing in the pattern. * Change proper media roll. Missing printing on the left or right side of label Gray line on the blank label Irregular printing * Wrong label size setup. * Set the correct label size. * The print head is dirty. * The platen roller is dirty. * Clean the print head. * Clean the platen roller. * The printer is in Hex Dump mode. * Turn off and on the printer to skip the dump mode. 35 8. Maintenance This session presents the clean tools and methods to maintain your printer. 1. Please use one of following material to clean the printer. Cotton swab Lint-free cloth Vacuum / Blower brush 100% Ethanol or Isopropyl Alcohol 2. The cleaning process is described as following, Printer Part Method 1. Always turn off the printer before cleaning the print head. 2. Allow the print head to cool for a minimum of one minute. 3. Use a cotton swab and 100% Ethanol or Isopropyl Alcohol to clean the print head surface. Interval Clean the print head when changing a new label roll Print Head Platen Roller Tear Bar/Peel Bar 1. Turn the power off. Clean the platen roller when 2. Rotate the platen roller and wipe it changing a new label roll thoroughly with water. Use the lint-free cloth with 100% As needed ethanol to wipe it. Sensor Compressed air or vacuum Monthly Exterior Wipe it with water-dampened cloth As needed Interior Brush or vacuum As needed Note: Do not touch printer head by hand. If you touch it careless, please use ethanol to clean it. Please use 100% Ethanol or Isopropyl Alcohol. DO NOT use medical alcohol, which may damage the printer head. Regularly clean the print head and supply sensors once change a new ribbon to keep printer performance and extend printer life. 36 Revise History Date Content 37 Editor TSC Auto ID Technology Co., Ltd. Corporate Headquarters 9F., No.95, Minquan Rd., Xindian Dist., New Taipei City 23141, Taiwan (R.O.C.) TEL: +886-2-2218-6789 FAX: +886-2-2218-5678 Web site: www.tscprinters.com E-mail: printer_sales@tscprinters.com tech_support@tscprinters.com Li Ze Plant No.35, Sec. 2, Ligong 1st Rd., Wujie Township, Yilan County 26841, Taiwan (R.O.C.) TEL: +886-3-990-6677 FAX: +886-3-990-5577
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No Create Date : 2019:01:22 09:24:52+08:00 Creator : Microsoft® Word 2013 Modify Date : 2019:01:25 09:11:18+08:00 Has XFA : No Language : zh-HK XMP Toolkit : XMP Core 5.5.0 Creator Tool : Microsoft® Word 2013 Producer : Microsoft® Word 2013 Format : application/pdf Document ID : uuid:0acf4aac-6016-4435-a0c1-e01554920b21 Instance ID : uuid:f183d4ae-9de1-48d9-8a93-5775a3371878 Page Count : 48EXIF Metadata provided by EXIF.tools