TTE Technology 32D100 LCD TV User Manual

TTE Technology, Inc. LCD TV 70 32MS55 QSG9A

a href="https://usermanual.wiki/TTE-Technology" itemprop="url"> TTE Technology >

User Manual

Ready. Set. Go!D-Series / D100
Model No. Serial No.Purchase Date Dealer/Address/PhoneCaution: To reduce the risk of electric shock, do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualied service personnel. This symbol indicates “dangerous voltage” inside the product that presents a risk of electric shock or personal injury. This symbol indicates important instructions accompanying the product.This symbol indicates that this product incorporates double insulation between hazardous main voltage and user accessible parts. When servicing, use only identical replacement parts. CAUTIONRISK OF ELECTRIC SHOCK.DO NOT OPEN.WARNINGTo reduce the risk of re or electric shock, donot expose this product to rain or moisture. dripping or splashing. Noobjects lled withThis product should not be exposed to liquids, such as vases, should be placed on the apparatus.WARNINGThe TV is unstable if it is not properly attachedto the base or mounted to the wall. Please follow the base or wall mounting instructionsprovided in the User’s Guide to ensure your safety.Warning: The batteries shall not be exposed to excessive heat such as sunshine, re or the like.Important InformationRefer to the identication/rating label located on the back panel of your product for its proper operating voltage.Cable TV Installer: This reminder is provided to call your attention to Article 820-40 of the National Electrical Code (Section 54 of the Canadian Electrical Code, Part 1) which provides guidelines for proper grounding and, in particular, species that the cable ground should be connected to the grounding system of the building as close to the point of cable entry as practical.Important: This television is a table model and is designed to sit on a rm, at surface. Don’t place the TV on soft carpeting or similar surface because the ventilation slots on the bottom of the unit will be blocked, resulting in reduced lifetime from overheating. To assure adequate ventilation for this product, maintain a spacing of 4 inches from the top and side of the TV receiver and 2 inches from the rear of the TV receiver and other surfaces. Also, make sure the stand or base you use is of adequate size and strength to prevent the TV from being accidentally tipped over, pushed o, or pulled o. This could cause personal injury and/or damage to the TV. Refer to the Important Safety Instructions on the next page.The Power button (followed by the power symbol) on this TV and your remote control puts the TV into a very low-power standby mode but will not completely turn the power o. In order to completely shut the power o, you will need to disconnect the power cord from the outlet. The mains plug/appliance coupler is used to completely turn o the device. If you prefer to completely turn o the device, you should install the TV in a manner that allows you to disconnect the power Product Registration Please register your TCL TV purchase on-line at www.tclusa.com. It will make it easier to contact you should it ever be necessary. Registration is not required for warranty coverage.Product Information Keep your sales receipt to obtain warranty parts and service and for proof of purchase. Attach it here and record the serial and model numbers in case you need them. These numbers are located on the product.Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Keep the apparatus at least 20cm far sway trom the human body.To bring you better visual experience, please remove the energy guide label, it available, trom TV tront panel and screen betore use.Antenna/Cable 480i, 480p, 720p, l080i (NTSC, ATSC, and QAM formatalComposite Video 480i, 576iHDMI 480i, 480p, 720p/60Hz, 1080i/60Hz, 1080p/60Hz, 576i/p, 1080i/p/50HzInput Signat Compatibility1
Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5. Do not use this apparatus near water.6. Clean only with dry cloth.7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other . A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.11.Only use attachments/accessories specied by the manufacturer.12.Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13.Unplug this apparatus during lightning storms or when unused for long periods of time.14.Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. ANSI/NFPA15.If safety relevant, the following information should be included as far as applicable:- minimum distances around the apparatus for sucient ventilation;- the ventilation should not be inpeded by covering the ventilation openings with items, such as newspapers, table-cloths, curtains, etc.;- no naked ame sources, such as lighted candles, should be placed on the apparatus;- attention should be drawn to the environmental aspects of battery disposal;- the use of apparatus in tropical and/or moderate climates.16.If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-2011 (Section 54 of Canadian Electrical Code, Part 1) provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead in wire to an antenna-discharge unit, size of ground-ing conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See following example: ANTENNA LEAD IN WIREGROUND CLAMPANTENNA DISCHARGE UNIT (NEC SECTION 810-20)GROUND CLAMPSGROUNDING CONDUCTORS (NEC SECTION 810-21)ELECTRIC SERVICEEQUIPMENT POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PARTH)2
Download:
Mirror Download [FCC.gov]
Document ID3058377
Application IDayiYTa8xRTq4u1k0788uzA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize181.15kB (2264368 bits)
Date Submitted2016-07-11 00:00:00
Date Available2016-07-11 00:00:00
Creation Date2016-07-05 16:40:39
Producing SoftwareAdobe PDF library 11.00
Document Lastmod2016-07-06 10:12:37
Document Title70-32MS55-QSG9A
Document CreatorAdobe Illustrator CC 2014 (Windows)
FCC ID Filing: W8U32D100

Navigation menu