TTI Tech GMRS7001 FRS/ GMRS Combination User Manual users manual
TTI Tech Co., Ltd. FRS/ GMRS Combination users manual
TTI Tech >
users manual
128-XXXX
1 of
General Mobile Radio Service (GMRS)
Model : GMRS7001
Draft :
Owner's Manual
1-800-290-6650
DRAFT
Feb.04,2003(by TTI).
128-XXXX
2 of
NEVER ATTEMPT TO CHARGE ALKALINE OR DRY CELL BATTER-
IES, AS BATTERIES MAY BURST CAUSING PERSONAL INJURY
AND DAMAGE TO THE PRODUCT. WHEN RECHARGING NICKEL
METAL HYDRIDE (Ni-MH) BATTERIES WITH THE AUDIOVOX
CHARGER, USE ONLY AUDIOVOX APPROVED RECHARGE-
ABLE BATTERIES. USE OF THE AUDIOVOX CHARGER WITH
OTHER BRANDS OF BATTERIES IS NOT RECOMMENDED, AS
BATTERY CHARGING TIMES WILL VARY WITH
DIFFERENT BRANDS. REFER TO THE MANUFACTURER’S
INSTRUCTIONS FOR CHARGING OTHER BRANDS OF BATTERIES.
AVOID PLACING THE GMRS7001-2 RADIO TRANSCEIVER
FOR PROLONGED PERIODS OF TIME IN DIRECT SUNLIGHT
OR TEMPERATURES BELOW -4° F (-20° C) OR ABOVE 140 ° F
(60° C).
KEEP THE ANTENNA AT 1 INCH (2.5 cm) AWAY FROM YOUR
HEAD AND BODY. DO NOT USE YOUR GMRS7001-2 RADIO
TRANSCEIVER WITH A DAMAGED ANTENNA.
PLACE THE RUBBER COVER ON JACKS WHEN NOT IN USE.
GMRS LICENSE:
USE OF THIS RADIO WITHIN THE UNITED STATES REQUIRES AN
FCC GMRS LICENSE. AN INDIVIDUAL18 YEARS OF AGE OR
OLDER, WHO IS NOT A REPRESENTATAIVE OF A FOREIGN
GOVERNMENT, IS ELIGIBLE TO APPLY FOR A GMRS SYSTEM
LICENSE. YOU WILL NEED TWO FORMS FROM THE FCC; FCC
FORM 159 AND FCC FORM 605 MAIN FORM AND SCHEDULE F.
YOU CAN FIND THE FORMS ONLINE AT: HTTP://WWW.FCC.GOV/
FORMPAGE.HTML, OR CALL 1-800-418-3676.
CAUTIONS
2
128-XXXX
3 of
DRAFT
3
1. Battery Cover
2. Monitor/Function Confirmation
Button
3. Detachable Carry Clip
4. Push-To-Talk (PTT) and Func-
tion Confirmation Button
5. Antenna
6. External Speaker(SP.)/Micro-
phone (MIC) Jacks
7. Built-in Speaker
8. Liquid Crystal Display (LCD)
9. Built-in Microphone
Model GMRS7001-2 (FCC License Required)
10. Up Channel/Volume Button
11. Down Channel/Volume
Button
12. MODE / WX Button
13. Power On/Off &
Key lock button
SCAN / VOX Button
14. Battery Charging Contacts
15
3
5
4
1
2
913
11
8
10
12
7
3
(REF)
1
(REF)
6
15.
14
128-xxxxx
4 of
4
Model GMRS7001-2 DISPLAY
1. Beep Tone Indicator: Icon appears when beep button confirmation
tone is selected; icon disappears when tone is off.
2. Key Lock Indicator: Icon appears when the keypad is locked. This
function disables keys such as channel up/down and MODE.
3. Monitor Indicator: Icon appears when the Monitor (M) button is
pressed and the channel monitor function is activated.
4 . Signal Strength Indicator: Icon appears when a signal is being received.
The icon consists of five bars to indicate the received signal level. The
icon also represents transmit signal power during transmission.
6. Large Segment Display: Indicates the channel number in use.
7. Scan Indicator: This function allows the user to scan a channel and/or a
tone code every .5 second to search for a valid signal.
9. Battery Level Indicator: Icon indicates the battery charge level.
5. Hi/LO Indicators: Appropriate icon appears when the transmit power
is set to desired output power.
1
2
3
4
10
5
6
7
8
9
11
13
14
12
8. RogerBeep Tone On/Off Indicator: This icon appears when the
Roger Beep tone is on, and disappears when tone is not in use.
10.Signal Receiving Indicator: Icon appears when a signal is being
received.
128-xxxx
5 of
5
11.Weather Mode Indicator: Icon will be on steady when in the weather
band mode. The icon will blink when in the GMRS mode with the alert
active.
12.Small Segment Display: Displays the CTCSS tone option in the
channel from (00-38).
13.Dual Watch Mode Indicator: Icon appears when dual watch mode is
active.
14.Voice Activated Transmission (VOX) Indicator: This function allows
hands free conversation. The icon appears when the VOX mode is
activated.
Powering the transceiver:
Equipment and Accessories Supplied
1. Radio (2) GMRS7001-2
2. Owner’s Manual (1) 128-xxxx
Your GMRS7001-2 radio transceiver operates on five AAA batteries.
Alkaline batteries will provide slightly better performance than rechargeable
batteries. Only the supplied Audiovox-approved rechargeable batteries
can be recharged in the radio transceiver using the suppiled desk-top
charger and associated wall adapter. This will ensure optimum
performance for the GMRS7001-2. Battery charging time is typically
13-15 hours. Use of the Audiovox charger with other brands of batteries is
not recommended as battery charging times will vary. Refer to the
manufacturer’s instructions for charging other brands of batteries.
Batteries
There are three methods of powering the GMRS7001-2:
1. Alkaline Batteries.
WARNING: Do not attempt to recharge Alkaline batteries.
2. Audiovox Rechargeable Ni-MH Batteries - (Rechargeable Ni-MH
batteries, Wall Adapter and Charging Stand are NOT included).
128-xxxx
6 of
DRAFT
6
2. Slide the cover
down and then lift
cover at bottom to
open.Remove
cover.
3. Insert five AAA batteries
(positive (+) end toward
the right begining at top
side and alternating
positive terminals as
shown).
1. Using thumb,
press down on
battery cover at
arrow and slide
cover down to
open.
Use only Audiovox-approved rechargeable batteries and charger
when charging batteries internal to the unit.
NOTE: To extend battery life, avoid overcharging the batteries.
3. Various Brands of Rechargeable Batteries - Use of the
Audiovox charger with other brands of rechargeable batteries is not
recommended, as battery charging times will vary with different
brands of batteries. Refer to the manufacturer’s instructions for
charging other brands of batteries.
Installing the batteries:
Battery installation is made more convenient when the carry clip is removed.
To do this, release the spring clip securing the belt clip to radio and slide
the belt clip upward and away from the radio body. Next, press down with
the thumb at the embossed arrow, slide the battery cover down and lift off
the battery cover. Insert five AAA batteries (alternate positive ends (+) toward
the top of the transceiver, starting up-to-down.
RELEASE
BUTTON
BATTERY
COVER
BELT
COVER
ARROW
POSITIVE
TERMINALS
CLIP
+
+
+
+
+
128-xxxx
7 of
DRAFT
7
The following guidelines will improve performance and provide longer
operating times for the GMRS7001-2:
1. Do not mix old and new batteries.
2. The use of alkaline-type batteries is recommended to provide the
longest operating time.
3. Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
4. If the unit is not to be used for an extended period of time, remove the
batteries. Old or leaking batteries can cause damage to the unit and
will void the warranty.
128-xxxxx
8 of
7
NOTE:
To switch between GMRS/FRS and Weather Band modes, press and hold
the Mode button for 2 seconds. Refer to the appropriate section of this
manual for detailed operating instruction for each mode.
GMRS7001-2 OPERATIONAL MODES
CHANNEL
SELECT
BUTTON
BEEP
WEATHER BAND
ALERT
CALL
SELECT
GMRS / FRS BAND
WEATHER BAND
BUTTON
BEEP
ROGER
BEEP
DUAL
WATCH
POWER
SELECT
CTCSS
SELECT
CHANNEL
SELECT
128-xxxxx
9 of
9
Controls:
Power On/Off (13) Button
Press and hold the power on/off button ( ) for at least 2 seconds. You will
hear a confirming melody to indicate the unit is on. To turn the unit off, press
and hold the button for at least 2 seconds.
Adjusting the Volume
With the unit powered on, press the Up Channel/Volume button ( ) to
increase volume and the Down Channel/Volume button ( ) to decrease
volume. The display will indicate the current volume level by the small
number in the icon ( UL 0 - 7 ).
Monitor/Display Backlight Button (2)
This button is used to to check activity on the current frequency before
transmitting. Check activity by pressing the Monitor (M) Button longer
than 2 seconds; the icon will apppear on the display and you will
hear static if frequency is clear.
Do not transmit if you hear conversation.
Hold down the Monitor Button again longer than 2 seconds and the
icon will disapppear from the display.
The monitor function will temporarily bypass the squelch setting and play
all signals on a given channel. This feature is useful when communicating
with other parties at extreme range.
By pressing the monitor button momentarily, the LCD backlight is turned
on; the LCD backlight will turn off automatically in about 5 seconds, or
when the monitor button is pressed momentarily once again.
Push To Talk (PTT) Button (4)
Pressing and holding this button will allow you to speak to any transceiver
that is set to the same channel and privacy code setting as yours. Hold the
transceiver approximately 1 to 2 inches from your face as you speak into
the built in microphone (9). After you have finished speaking, release the
PTT Button to allow reception of incoming signals. It is not possible to
128-xxxx
10 of
10
transmit and receive at the same time.
While the PTT Button is pressed,
the signal indicator will display the relative strength of the transmitted
signal. Releasing the button allows the unit to revert to standby mode.
When receiving an incoming signal, the BUSY icon will display in the
LCD and the received signal strength indicator ( ) will display
the relative strenth of the signal. The PTT Button can also be used as a
two-way call ringer. Pressing the button twice quickly will call another par-
ty on the same channel.
Up Channel/Volume Button (10)
In the standby mode, pressing this button will increment the listening
volume. When in function edit mode this button will be used to adjust the
unit's settings.
Down Channel/Volume Button (11)
In the standby mode, pressing this button will decrement the listening
volume. When in function edit mode this button will be used to adjust the
unit's settings.
Mode Button (12)
This button is used to select various feature settings in the GMRS / FRS or
weather band mode. Holding the MODE button longer than 2 seconds
will toggle between the GMRS/FRS and weather band modes.
128-xxxxx
11 of
11
External Speaker (SPK)/Microphone (MIC) Jacks (6)
This set of jacks accepts an Audiovox headset/microphone connector.
Scan / VOX Button (14)
Press this Button momentarily to enable or disable the scan mode. Press
and hold Button for more than 2 second to enable or disable the VOX.
When in the VOX mode,the VOX icon will display in the bottom left corner.
Operating Modes and Features
GRMS Operation
- From GMRS/FRS standby mode, press and hold the ( ) button
for 2 seconds to turn on power.
- Press the MODE button so the Channel number flashes.
- Select the desired channel with the Up (10) and Down (11) Buttons.
When receiving a call, the signal strength meter appears to indicate
incoming received signal strength.
- Press and hold the PTT button (4) to transmit, then speak into the
microphone clearly and slowly. the signal indicator will display the
- Release PTT Button (4) to receive.
- Communication can only be accomplished when the channel and
CTCSS tone frequency of at least two parties are the same.
- The small segment will be displayed on the LCD panel if the CTCSS
tone frequency function is enabled.
relative strength of the transmitted signal.
128-xxxxx
12 of
12
Channel Selection
To change the channel,
- From GMRS standby mode, press the MODE button (12) until the
channel number flashes.
- Press the Up Button (10) briefly to move to the next higher main
channel number.
- Press the Down Button (11) briefly to move to the next lower main
channel number.
CTCSS Mode (Sub-Channel) Selection
Coded Tone Controlled Squelch System (CTCSS) with 38 Sub-Frequencies.
This feature allows you to utilize the coded squelch tones (00–38) within a
main channel. This enables you to communicate with another party on the
same main channel using the same subcode. (This filters out unwanted
transmissions without the same coded squelch tone). There are 38 CTCSS
Sub-channels for each main channel. A different subcode may be
selected for each of the 15 channels.
To change the CTCSS Sub-channel,
In order to communicate with other GMRS units, both transmitting and
receiving party must be on the same frequency.
The GMRS7001-2 has 22 channels (frequencies) indicated by the large
digits on the LCD display panel. Channels 1 through 7 are the shared
GMRS/FRS channels. Channels 8-14 are FRS only channels, while
channels 15-22 are assigned GMRS only channels. When this device is
channel (8-14) has been selected, the HI or LO indicator will not be
displayed on the LCD panel; otherwise, for channels 1-7 (GMRS/FRS)
and 15-22 (GMRS only), the HI or LO indicator will be displayed. Com-
munication with Audiovox FRS and compatible units is possible on these
seven channels. Before transmitting on the selected channel, press the
Monitor (M) Button (2) to check the activity on that channel. If there is activity
on the selected channel, change to another channel that is clear.
being used on the FRS channels, (channels 8-14), the radio will auto-
matically switch to the low power setting, which is 0.3 watts. If an FRS only
128-xxxxx
13 of
13
- Then press the Up or Down button to select the desired sub-channel
for use.
- Press the Power On/Off button momentarily to confirm selection.
The CTCSS mode can be turned off by selecting the oF icon as the setting.
NOTE: To communicate with other GMRS units, they must be switched to
the same channel and CTCSS subcode. To communicate with
other GMRS units that do not have subcodes, switch your unit to
the same channel with the subcode set to oF.
The CTCSS subcodes do not prevent others from hearing your
transmission. This will only allow you to ignore all traffic on a
given channel not using the same subcode.
VOX Selection Mode
This option enables you to have hands-free conversation. Your voice or
nearby sound is detected and the radio transmits without the need to
press the PTT button.
To set radio for VOX operation,
- From GMRS/FRS standby mode, press and hold the SCAN button until
the VOX icon appears on the display.
- Press the Up or Down button to select VOX sensitivity from 1 to 5.
- Momentarily press the PTT button to confirm the VOX selection.
VOX can be turned off by pressing the SCAN button for 2 seconds.
- From GMRS standby mode, press the Mode Button twice; a flashing
oF or sub-channel number is displayed. If oF is displayed, press the
Up or Down button to enable the CTCSS mode; the CTC icon will
appear steady on the display with the flashing sub-channel number.
128-xxxxx
14 of 28
14
Channel Scan Operation
This feature allows you to monitor all channels automatically for valid
signals. While scanning, you can transmit and receive. When a signal is
received, the scan is interrupted and will return to scan mode 5 seconds
after reception is terminated.
NOTE:
While the scan function is active, the MODE button will be inoperative. The
scan mode will reduce the overall battery life due to the battery save
function is overridden.
To enable the channel scan mode,
- From GMRS/FRS standby mode, momentarily press the SCAN
Button ; SCAN icon will appear on the LCD display.
- The radio will display each channel (1-22) in order as the scan mode
operates to find an active main channel.
- When unit doesn't find any signals and you want to transmit, press
the PTT switch to return to home channel operation. The transceiver
will automatically resume scanning approximately 5 seconds after
the communication is completed.
- If there is no activity and you want to leave the scan mode, press the
SCAN button momentarily and the unit will return to normal operation;
(SCAN) icon will disappear from the LCD display.
128-xxxxx
15 of
15
Dual Watch Mode
This feature allows you to monitor two channels at the same time. While in
dual watch mode, the unit will continuously monitor both the primary and
dual watch channel. Received signals will be played for 5 seconds, then
the unit will resume scanning the two channels. Pressing the PTT button
during a received transmission will set the unit to transmit on the same
channel. Pressing the PTT button when no signal is received will set the
unit to transmit on the primary channel.
To set the Dual Watch Mode:
- From GMRS/FRS standby mode, press the MODE button until the DW
icon flashes on the display. If the dual watch mode is off, the oF icon
will also appear flashing.
- To enable the dual watch mode, press the Up or Down button; the dual
watch channel number will flash and start to increment up or down as
the Up or Down button is pressed.
- Press the MODE button again to select the CTCSS function and select
the CTCSS code if desired for the dual watch channel just selected.
- Press the PTT button to confirm selection of the dual watch channel.
The display will now alternate between the primary channel and the
dual watch channel just selected.
Momentarily press the SCAN button to exit the dual watch mode.
128-xxxxx
16 of
16
Key Tone
This feature allows the transceiver to sound a confirmation tone whenever
the following keys are pressed: Monitor (M) Button, Up/Down Buttons, MODE
Button, SCAN Button, or the EMG Button.
To turn the key tones on or off,
- From GMRS/FRS standby mode, press the MODE Button until bp ,
the Bell ( ) icon, and On or oF flash on the LCD display.
- Press the Up or Down Button to toggle the key tone feature On or Off.
- Press the PTT button momentarily to confirm selection.
When the key tone feature is on, the Bell icon appears steady on the
display, and the beep tones sound in response to button activation.
Transmit Power Selection Mode
This feature permits selection of the transmitting power level to high
(3.0 watts)or low (0.5 watt). Using low power the unit will have a lower
transmit range but battery life will be increased.
To access the transmitter power selection function:
- From GMRS/FRS standby mode, press the MODE Button until the Po
icon appears with a flashing HI or LO indication on the display.
- Press the Up or Down button to toggle between the High and Low se-
lections.
- Press the PTT button momentarily to confirm selection.
The display will indicate the current setting in standby mode.
Roger Beep Tone
The Roger Beep is a tone which is automatically transmitted whenever the
PTT button is released. This tone alerts the receiving party that the trans-
mission has been terminated intentionally.
128-xxxxx
17 of
17
To enable and disable the Roger Beep tone:
- From GMRS / FRS standby mode, press the MODE Button until rb
appears on the display with the flashing Roger Beep icon ( ) and
On or oF.
- Press the Up or Down Button to select the tone on or off as desired.
- When enabled, the tone icon ( ) appears steady on the display.
- Press the Power On/Off button momentarily to confirm selection.
Call Ringer Selection Mode
The transceiver provides 5 user-selectable call ringer melodies to alert
you to an incoming call.
To select your favorite call ringer melody:
- From GMRS / FRS standby mode, press the MODE button until
CA will appear on the display, together with a flashing number be
tween 1 and 5, and an appropriate call ring.
- Press the Up or Down Button to preview and hear the 5 available call
melodies.
- Press the PTT button momentarily to confirm selection.
Refer to the PTT button (4) to transmit ring signal.
Auto Key Lock Selection Mode
This feature prevents accidental channel change to the preferred settings
of the unit. The Auto Key Lock function temporarily disables the Up, Down
and Mode Buttons.
To access the Auto Key Lock selection menu:,
- From GMRS / FRS standby mode, momentally press the Power
Button to Lock the Auto Key function;
the ( ) icon appears on the display.
- The PTT and Monitor Buttons are not effected.
- To unlock the Auto Key function, press the power button momentally
and the icon ( ) disappears from the display.
128-xxxxx
18 of
18
Weather Band Operation
Channel Selection
This feature provides access to 10 channels within the weather band (7
NOAA channels and 3 Canadian marine channels. To select a weather
channel, the unit must be in the weather channel mode. Press and hold
the MODE button for at least 2 seconds; the weather alert icon ( ) will
appear, together with a channel number in the band. Press the MODE
button (12) until the channel number flashes.
To change the channel,
- Press the Up Button (10) briefly to move to the next higher
main channel number.
- Press the Down Button (11) briefly to move to the next lower main
channel number.
Weather Alert Mode
The weather alert mode notifies the user of unusual weather situations.
To access the weather alert function:
- From Weather Band standby mode, press the MODE button once to
access the weather channels and use the Up or Down Button to
select the desired channel.
- Press the MODE button again to access the weather alert function;
weather icon ( ) and AL On or oF appear flashing on the display.
- Use the Up or Down buttons to enable (On)/disable (oF) the alert
function. The weather icon will stop blinking on the display when the
alert is disabled.
- Press the PTT Button to confirm your selection.
- Press and hold the MODE button for at least 2 seconds to exit the
weather function.
Whether the unit is in GMRS or weather band mode, if a weather alert
signal is received, the unit will generate a warning tone. To silence the
warning tone, press any key except the PTT button. The unit will then revert
to a previously selected weather channel and the weather alert will be
heard.
128-xxxxx
19 of
Key Tone
This feature allows the transceiver to sound a tone whenever the following
keys are pressed: Monitor (M) Button, Up/Down Buttons, MODE Button,
SCAN Button.
To turn the key tones on or off,
- From GMRS / FRS standby mode, press the MODE button
until bp,the Bell ( ) icon, and On or oF flash on the LCD display.
- Press the Up or Down Button to toggle the key tone feature On or Off.
- Press the PTT button momentarily to confirm selection.
When the key tone feature is on, the Bell icon appears steady on the display
and the beep tones sound in response to button activation.
19
Battery Alert
When the battery icon ( ) blinks on the LCD panel, recharge unit or
install fresh batteries. If the batteries are not replaced the ( ) icon will
appear and an audio tone will sound to warn the user that the batteries
must be replaced.
128-xxxx
20 of
20
NOTES FOR GOOD COMMUNICATION
1 . The GMRS7001-2 22 channels are shared on a ‘take turns’ basis.
This means other groups may be talking on any of the channels.
A common code of ethics/courtesy is to switch to another vacant
channel and not to attempt to talk over someone who is already using
the channel you first selected.
2. The GMRS7001-2 has been designed to maximize performance
and improve transmission range in the field. To avoid interference,
it is recommended that you do not use the units closer than 5 feet
apart.
3. For best transmission results, always keep your mouth about 2-3
inches from the microphone (9) and speak slowly in a normal voice.
4. To increase battery life, avoid features such as Scan and Dual
Watch. These features will reduce operating time considerably.
Warning
•Do not operate the transceiver unless you are licensed to do so.
•Remove the battery from the transceiver if it is not expected to be used
for long periods. This will eliminate the possibility of chemicals leaking
from the battery and corroding the transceiver.
•Avoid exposing the transceiver to water or extremes of temperature.
•Do not use this device in or near a mining facility, which uses remotely
triggered explosives or in areas labeled “Blasting Area”. Premature or
accidental detonation may result.
•Do not attempt to modify or in any way increase the output of this
transceiver. Its output is designed to meet the legal limits set by the FCC.
•Do not use this device or change the battery in potentially explosive
atmospheres as sparks in such areas could result in an explosion.
•Turn your transceiver off wherever posted notices restrict the use of radios
or cellular telephones. Facilities such as hospitals may use equipment
that is sensitive to RF energy.
128-xxxx
21 of
21
Troubleshooting
•Turn your transceiver off on board aircraft when requested to do so.
•Do not place your radio in front of a vehicle’s air-bag. If the air-bag deploys,
it could propel the transceiver like a projectile causing bodily injury.
Weak or no Weak battery pack Charge or replace battery
signal received Channel and privacy Adjust the transceiver’s
code not set the same settings to match those
as target transceiver settings of the target
transceiver
Volume level too low Increase volume level
PTT Button inadvertently Release PTT Button
depressed
Excessive radio interference Change to a different
on a particular channel channel
Obstruction of radio signal Avoid operating in or near
large buildings or
obstructions
Unit beeps, but Battery pack extremely Charge or replace battery
will not function discharged pack
when turned on
Reception of CTCSS privacy mode Turn on the CTCSS privacy
unwanted signals not on mode and set code number to
match the setting of the
target transceiver.
Interference from Turn the devices off or move
electronic devices such farther away from them.
as computers or TVs
Problem Possible cause Correction
No transmission Weak battery pack Charge or replace battery
while pressing pack
the PTT Button
128-xxxxx
22 of
DRAFT
General
Frequency Range:
Channels 1 through 7 are
shared with FRS radios. Refer to frequency chart on next page.
Channels 8 through 14 are
FRS only. Refer to frequency chart on next page.
Channels 15 through 22 are
GMRS only. Refer to frequency chart on next page.
Channel Spacing 12.5kHz
Privacy Codes 38 for each main channel
Dimensions (W x H x D) 2.17 W x 4.02 H x 1.14 D
(Without Antenna) (55 mm x 102 mm x 29 mm)
Power Supply
Power Source Alkaline Batteries, AAA (5), 7.5 VDC
Ni-MH rechargeable, AAA (5),
6.0 VDC, 650 mAh
Operating Time hours Low Power
(Transmit: Receive: Standby) hours High Power
(5: 5: 90 ratio) (Based on alkaline batteries)
Receiver
Useable Sensitivity >-119 dBm
Maximum Audio Output Power > 0.3 Watt maximum (8 Ohm )
Modulation Distortion < 5% (1 kHz 70%)
Transmitter
RF Output Power 3.0 Watts maximum (high power)
0.5 Watt maximum (low power)
Maximum Deviation +/- 2.5 kHz
Modulation Distortion < 5% (1 kHz 70%)
22
Technical Specifications ;
Weather Band (7 Channels) 162.4000 - 162.5500 MHz
Canadian Maritime (3 Channels) 161.6500, 161.7750, 163.2750 MHz
128-xxxxx
23 of
DRAFT
23
CHANNEL/TYPE FREQ(MHz)/PWR CHANNEL/TYPE FREQ(MHz)/PWR
1 GMRS/FRS 462.5625 12 FRS 467.6625
2 GMRS/FRS 462.5875 13 FRS 467.6875
3 GMRS/FRS 462.6125 14 FRS 467.7125
4 GMRS/FRS 462.6375
5 GMRS/FRS 462.6625
6 GMRS/FRS 462.6875
7 GMRS/FRS 462.7125
8 FRS 467.5625
9 FRS 467.5875
10 FRS 467.6125
11 FRS
467.6375
15 GMRS 462.5500
16 GMRS 462.5750
17 GMRS 462.6000
18 GMRS 462.6250
19 GMRS 462.6500
20 GMRS 462.6750
21 GMRS 462.7000
22 GMRS 462.7250
This transceiver complies with FCC regulations for use in the United
States of America. Use in other countries may be prohibited or restricted
by local regulation.Please check with the local regulating agency before
using this device outside the United States of America.
Main Channel Frequencies :
NOTE : Channels 1 through 7 are shared with FRS radios.
Channels 8 through 14 are FRS only.
Channels 15 throuhg 22 are GMRS only.
128-xxxx
24 of
24
1 162.550 6 662.500
2 162.400 7 162.525
3 162.475 8*161.650
4 162.425 9*161.775
5 162.450 10*163.275
*Canadian Marine
Channel Freq. MHz Channel Freq. MHz
Weather Channel Frequencies:
128-xxxxx
25 of
DRAFT
Continuous Tone Coded Squelch System Tone
Frequencies (in Hz)
CTCSS Freq. Hz CTCSS Freq. Hz
1 67.0 20 131.8
2 71.9 21 136.5
3 74.4 22 141.3
4 77.0 23 146.2
5 79.7 24 151.4
6 82.5 25 156.7
7 85.4 26 162.2
8 88.5 27 167.9
9 91.5 28 173.8
10 94.8 29 179.9
11 97.4 30 186.2
12 100.0 31 192.8
13 103.5 32 203.5
14 107.2 33 210.7
15 110.9 34 218.1
16 114.8 35 225.7
17 118.8 36 233.6
18 123.0 37 241.8
19 127.3 38 250.3
* oF = No Tone
25
128-xxxxx
26 of
DRAFT
90 DAY LIMITED WARRANTY
AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788
1-800-290-6650
128-5385A
Applies to Audiovox Family Radio and General Mobile Service Products.
AUDIOVOX CORPORATION (the Company) warrants to the original retail purchaser of this
product that should this product or any part thereof, under normal use and conditions, be proven
defective in material or workmanship within 90 days from the date of original purchase, such
defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option)
without charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is to be delivered
with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s),
transportation prepaid, to the warranty center at the address shown below.
The Company disclaims liability for communications range of this product.
This Warranty does not apply to any product or part thereof which, in the opinion of the
Company, has suffered or been damaged through alteration, improper installation, mishan-
dling, misuse, neglect, accident, or by removal or defacement of the factory serial number/
bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY
IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT,
SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY
PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE
LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH
OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MER-
CHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF
ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is
authorized to assume for the Company any liability other than expressed herein in connection with
the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion
or limitation of incidental or consequential damage so the above limitations or exclusions may
not apply to you. This Warranty gives you specific legal rights and you may also have other
rights which vary from state to state.
26