TYT ELECTRONICS TYT-A5 Scanning Receiver User Manual
TYT ELECTRONICS CO., LTD Scanning Receiver
user manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3467254 |
| Application ID | Jr7zdxc7WnUFKiTWyWbB8g== |
| Document Description | user manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 242.61kB (3032644 bits) |
| Date Submitted | 2017-07-17 00:00:00 |
| Date Available | 2017-07-17 00:00:00 |
| Creation Date | 2017-01-12 15:20:38 |
| Producing Software | Adobe PDF library 10.01 |
| Document Lastmod | 2017-01-13 11:16:31 |
| Document Title | æ‰“å° |
| Document Creator | Adobe Illustrator CC 2014 (Windows) |
Getting Familiar MIC / SP is USER'S MANUAL Scanning Receiver Basic operation 1 Scan Function When the radio is allowed to be scanned, which can be set by the software. you can press the PTT key to turn on or turn off the scan. When the scan begins.indicators lights green. the radio will can scan automatically from channel 1 to 16 which is defined as scan added. When there is signal in the scanning channel, it will stop in the channel for talk. Note: When there is signal in the scanning channel, it will stop in the channel for a talk and after several seconds. Please note that scan is only available when there are two or more than two memory channels and two or more scan added channels 2. Battery Save Function This function can be set by the software. Turn on this function can make the standby time more longer. 使用说明书 3. Scrambler USER'S MANUAL When the radio is allowed the scrambler function. and press the key. TX voice will be sent out with scrambler. other radio only received the signal when its scrambler also turns on. 4 Busy Channel Lock You can turn on/off this function via software. A: if the current channel does not have CTCSS/DCS, When there is signal. TX prohibited when you press PTT. B: If the current channel does not have CTCSS/DCS. when there is signal which does not have CTCSS/DCS. TX prohibited vvhen you press PTT. C: If the current channels does not have CTCSS/DCS. vvhen there is signal which have CTCSS/DCS. the radio will transmit when you press PTT. 5. Wide/Narrow Bandwidth Setting 1 ) The voice prompt can be selected "Chinese/English/Tone/OFF" through the menu "Voice/Beep Tone" of the "Optional Features" in the software for. When choosing "OFF", voice prompt turns off. 2) Channel annunciation: You will get to know the working conditions of current channel which is being operated. 3) Low battery alert: The radio will alert you when the battery capacity reaches the minimum operating voltage. The default is wide band. You can select the wide band (25KHz) or narrow band(12.5KHz) through the menu "Channel Spacing" of the "Channel Edit" in the software. Low battery prompt 6 .VOX The default setting is Chinese voice prompt. When transmitting or standby. if the battery capacity reaches the pre-determined low level. the indicator light blinks red. and a low battery alert tone will be heard. The indicating tone can be "Please change the battery". When the low battery alert occurs. it can not transmit. please change or charge the battery. Speak to the microphone in normal voice to transmit, no need to press PTT switch, turn VOX on//off though the software. A: when VOX is on in your working channel. Speak to the microphone directly, it will transmit automatically. The radio stops transmitting when there is no voice, and waits for receiving. B: when a headset with a microphone is used. When VOX is on, you should VOX again for the radio to identify voice volume. If the microphone is too sensitive. the noise around radio will start transmitting. If the microphone is not sensitive. the radio can not collect your voice. Please Adjust VOX level well to guarantee smooth communications. English/Chinese Voice Prompt Voice prompt The default setting is Chinese voice prompt. and you will know the working condition of the radio with voice prompt. The purpose of TOT is to prevent any radio from talking in one channel for a long time. and to prevent the transceiver from being damaged because of continuous transmission If the transmitting time exceeds the TOT pre-set time. the radio will sound "Du". Power protection function When the radio is in normal use or maintenance, the transmission will be prohibited if the working voltage is beyond the normal supplying voltage. Lower than 3V or higher than 5V, the transmission will be prohibition. The radio cannot power on when it is higher than 5V. Squelch function The squelch level will determine the signal strength to open the speaker of the radio. If the squelch level is lower. the background noise of opening the radios speaker will be higher. and the corresponding communication range will be further. but the anti-interference capacity will be weaker. The default setting of squelch level is 5. you can adjust it through the menu -Squelch Level" of the -Optional Features- in the software for. Level 0 to 9 can be selected. 0 is the lowest level. Time out timer (TOT) TX: 420-450MHz RX: 400-480MHz CTCSS/DCS CTCSS and DCS is the sub-audio signaling, to prevent the radio from receiving unwanted signal in the same channel. When the CTCSS/DCS is set, then within the communication range, you can only receive signals from the same channel with the same CTCSS/DCS setting. When the CTCSS/DCS is not set, you will get all the signal from the same channel within the communication range. 2.5 NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. WARNING:MODIFICATION OF THIS DEVICE TO RECEIVE CELLULAR RADIOTELEPHONE SERVICE SIGNALS IS PROHIBIITED UNDER FCC RULES AND FEDERRAL LAW.
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.5 Linearized : No XMP Toolkit : Adobe XMP Core 5.6-c011 79.156289, 2014/03/31-23:39:12 Format : application/pdf Title : 打印 Metadata Date : 2017:01:13 11:16:31+08:00 Modify Date : 2017:01:13 11:16:31+08:00 Create Date : 2017:01:12 15:20:38+08:00 Creator Tool : Adobe Illustrator CC 2014 (Windows) Thumbnail Width : 256 Thumbnail Height : 92 Thumbnail Format : JPEG Thumbnail Image : (Binary data 11522 bytes, use -b option to extract) Instance ID : uuid:c2f35a38-f01e-42f5-bdd5-06b1ec288731 Document ID : xmp.did:2001bf68-78fe-f442-9579-0ca45b4131b1 Original Document ID : uuid:5D20892493BFDB11914A8590D31508C8 Rendition Class : proof:pdf Derived From Instance ID : uuid:9f381827-0645-43eb-bab7-fb356cfc6fb2 Derived From Document ID : xmp.did:c13a1cc8-13fd-2d4b-92c5-75f2b11c6235 Derived From Original Document ID: uuid:5D20892493BFDB11914A8590D31508C8 Derived From Rendition Class : default History Action : saved, saved History Instance ID : xmp.iid:4f8bf90c-a3c0-4347-b9c3-49450ed33e80, xmp.iid:2001bf68-78fe-f442-9579-0ca45b4131b1 History When : 2017:01:11 11:34:39+08:00, 2017:01:12 15:20:38+08:00 History Software Agent : Adobe Illustrator CC 2014 (Windows), Adobe Illustrator CC 2014 (Windows) History Changed : /, / Startup Profile : Print Has Visible Overprint : False Has Visible Transparency : False N Pages : 1 Max Page Size W : 304.924309 Max Page Size H : 225.525971 Max Page Size Unit : Millimeters Font Name : ArialMT, Arial-Black, Arial-BoldMT, FZDHTJW--GB1-0 Font Family : Arial, Arial, Arial MT, 方正大黑简体 Font Face : Regular, Black, Bold, Regular Font Type : Open Type, Open Type, Open Type, TrueType Font Version : Version 5.10, Version 5.06, 001.001, 1.00 Font Composite : False, False, False, False Font File Name : arial.ttf, ariblk.ttf, ARIAL-BOLD.OTF, FZDHTJW.TTF Plate Names : Cyan, Magenta, Yellow, Black Swatch Groups Colorants Tint : 100.000000 Swatch Groups Group Name : 明亮 Swatch Groups Group Type : 1 Swatch Groups Colorants Swatch Name: C=60 M=90 Y=0 K=0 Swatch Groups Colorants Mode : CMYK Swatch Groups Colorants Type : PROCESS Swatch Groups Colorants Cyan : 60.000000 Swatch Groups Colorants Magenta : 90.000000 Swatch Groups Colorants Yellow : 0.003100 Swatch Groups Colorants Black : 0.003100 Producer : Adobe PDF library 10.01 Page Count : 3 Creator : Adobe Illustrator(R) 17.0 For : Administrator, Bounding Box : -365 -610 1340 -10 Container Version : 11 Creator Version : 18EXIF Metadata provided by EXIF.tools