Tamura TMRF RFID Reader/Writer User Manual

Tamura Corporation RFID Reader/Writer

User Manual

2D-53-00001000 TAMURA CORPORATION -1/ 16 - TMRF-1-U001-KM User’s Manual TAMURA CORPORATION
2D-53-00001000 TAMURA CORPORATION -2/ 16 - 1.Scope This document is the user’s manual of Radio Frequency Identification [RFID] Reader /Writer with Universal Serial Bus [USB] for Konica Minolta Business Technologies, Inc. 2.Product Name TMRF-1-U001-KM （Product reference code in TAMURA corporation：N-22200066-00） 3.Outlines of product ・This product is a compact RFID reader / writer with USB interface. ・This product can read and write data for RFID tag by 13.56MHz radio frequency with RFID wireless interface. ・The USB interface is capable of communicating by low speed [1.5Mbps].
2D-53-00001000 TAMURA CORPORATION -3/ 16 - 4.Safety Information Read the following safety information and handling information before using TMRF-1-U001 -KM to avoid injury. 4-1．Important safety information Failure to follow these safety instructions could result in fire, electric shock, or other injury or damage. ○DO NOT use this product in hospitals and health care facilities, especially near of sensitive equipments such as heart pacer to external radio frequency emissions. ○This product assumes the activity to a general electronic instrument.(AV equipments, OA equipments, amusement equipments, etc.) A very advanced reliability is required and the activity to the equipment and units (medical equipment, an aerospace plane machine, a nuclear equipment, various safety devices, etc.) with which a trouble and malfunction of a product are directly concerned with a human life cannot be performed. Failure to follow these handling instructions could result in damage to TMRF-1-U001-KM or other property. ○Since this product consists of precision electronic parts, please do not give a strong impact. If an impact is given to a product or it is made to fall, it will become a cause of a crash or a trouble. ○DO NOT put into a micro wave oven or a high-pressure container. It becomes a cause of a trouble. ○DO NOT use TMRF-1-U001-KM in rain or any wet location. ○Please do not install in an unstable location. If it is installed in a shaky stand top, a leaning place, etc., it will fall and will become a cause of a crash or an injury. ○Please do not pull a moving part and an attachment (especially connector) strongly, or do not bend them. They become a cause of a crash or a trouble. ○Keep this product out of the direct rays of the sun. It becomes a cause of a trouble. ○DO NOT use window cleaners, aerosol sprays, solvents, alcohol or abrasion to clean. ○This product is CMOS product. Please do not keep it in the place easily charged with electricity. It becomes a cause of a trouble. ○When you discard this product, please process as an industrial waste. Warning Caution
2D-53-00001000 TAMURA CORPORATION -4/ 16 - 4-2 .Operating condition TAMURA Corporation will grant a nonexclusive license of this product to user on condition of the following. ○DO NOT perform program analysis, reverse engineering, copy, change, re-distribution, etc. ○This product is a product approved by Wireless Telegraph Law of each country. You will be punished by violation of Wireless Telegraph Law if a transmitting output is raised by use of an external antenna, or reconstruction. ○The specification of this product and the contents of related data may be changed without a preliminary. ○This product is based on regulation of the following countries. Japan , the United States of America , Canada, Australia and New Zealand When it is in used except the countries which indicated, TAMURA Corporation cannot take responsibility. ○This equipment complies with FCC/IC radiation exposure limits set forth for uncontrolled equipment and meets the FCC radio frequency (RF) Exposure Guidelines in Supplement C to OET65 and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that it deemed to comply without maximum permissive exposure evaluation (MPE). But it is desirable that it should be installed and operated with at least 20cm and more between the radiator and person’s body (excluding extremities :hands, wrists, feet and ankles). ○Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment ○This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help. ○This device complies with Part 15 of FCC Rules and RSS-Gen of IC Rules. Operation is subject to the following two conditions : (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of this device.
2D-53-00001000 TAMURA CORPORATION -5/ 16 - 4-3. Notes of use ○DO NOT move adjustment parts of this product. ○When a metal thing is near this product or this product is covered by a metal thing, the characteristic may deteriorate remarkably. ○DO NOT insert a USB connector by force (even if it does not put in strong power, it can insert smoothly). It is NOT connectable unless it inserts at the right direction and the right angle. When you cannot insert, please check direction of a connector once again, without inserting by force. ○DO NOT use it in the environment where this product dews. 5.Product structure RFID R/W with USB [TMRF-1-U001-KM] ①USB connector ②RF CAP （The jack for external antennas） ※Prohibition of use ③The hole for a strap ④USB CAP ④ ① ② ③
2D-53-00001000 TAMURA CORPORATION -6/ 16 - 6.USB Control commands 6-1．USB communications protocol (host -> RFID R/W -> tag) Calling device request bmRequestType = 0x43,0xC3 bRequest =100+No. (The following table) wValue = not used wIndex = not used wLength = byte count data = parameter data 1~3 4 ~ n n+1 n+3 command parameter CRC16 EOT The following table The following table 2bytes 0x04 CRC16 calculation value parameter＝From command to EOT considers it as 1 text. No command function parameter1 parameter2 parameter3 00 “U00” ROM Version Read XX,XX YMD Nothing ○01 “U01” Inventory Nothing ○02 “U02” Stay Quiet UID(8) ○03 “U03” N Block Read(All data) (Max=9Blocks) UID(8) SBlock#(1) Block count(1) ○04 “U04” N Block Write(All data) ×05 “U05” Read Single Block UID(8)*1 Block#(1) ○06 “U06” Write Single Block UID(8)*1 Block#(1) data(4) ○07 “U07” Lock Block UID(8)*1 Block#(1) ○08 “U08” Read Multi Blocks (Max=9Blocks) UID(8)*1 SBlock#(1) Block count(1) ○09 “U09” Write Multi Blocks ×10 “U10” Select Tag UID(8) ○11 “U11” Reset to Ready UID(8)*1 ○12 “U12” Write AFI UID(8)*1 AFI(1) ○13 “U13” Lock AFI UID(8)*1 ○14 “U14” Write DSFID UID(8)*1 DSFID(1) ○15 “U15” Lock DSFID UID(8)*1 ○16 “U16” Get System Information UID(8)*1 ○17 “U17” Get Multi Block Security Status UID(8)*1 Sdata(1), data count(1) ○18 “U18” Write 2 Blocks UID(8)*1 Block#(1), 2(1) data1(4), data2(4) ○19 “U19” Lock 2 Blocks UID(8)*1 Block#1(1) ○20 “U20” ×21 “U21” Special process1（Buzzer etc） command data ○22 “U22” × notes：S=start、Block#=01∼64 Block count：Serial line max = 9 /USB max=9 “U03” is the same as “U08” Special process1(command)：0x80= Buzzer function(ON),0x40= Buzzer function(OFF),0x01= Buzzer(ON） "U18 [Write 2 Blocks]" and "U19 [Lock 2 Blocks]" are Tag-it. It is original command. Configuration of UID : There are 2 ways that all 8 bytes are assigned and an implementation-supplier code is assigned. (*1) E0 MM XX XX XX XX XX XX -> 00 MM XX XX XX XX XX XX [MM : an implementation-supplier code assigned = 04(Philips),05(My-D),07(TI)]
2D-53-00001000 TAMURA CORPORATION -7/ 16 - No command function parameter1 parameter2 parameter3 23 “U23” 24 “U24” 25 “U25” 26 “U26” 27 “U27” 28 “U28” 29 “U29” 30 31 “U31”* Inventory Nothing ○32 “U32”* Stay Quiet UID(8) ○33 “U33”* N Block Read(All data) (Max=9Blocks) UID(8)*1 SBlock#(1), Block count(1) ○34 35 “U35”* Read Single Block UID(8)*1 Block#(1) ○36 “U36”* Write Single Block UID(8)*1 Block#(1) data(4) ○37 “U37”* Lock Block UID(8)*1 Block#(1) ○38 “U38”* Read Multi Blocks UID(8)*1 SBlock#(1) Block count(1) ○39 40 “U40”* Select Tag UID(8) ○41 “U41”* Reset to Ready UID(8)*1 ○42 “U42”* Write AFI UID(8)*1 AFI(1) ×43 “U43”* Lock AFI UID(8)*1 ×44 “U44”* Write DSFID UID(8)*1 DSFID(1) ×45 “U45”* Lock DSFID UID(8)*1 ×46 “U46”* Get System Information UID(8)*1 ×47 “U47”* Get Multi Block Security Status UID(8)*1 Sdata(1), data count(1) ×48 “U48”* 49 “U49”* 50 51 52 ●* is command of a My-D card. ●My-D assumes 124Page (248Block) with the architecture of 4 bytes/Block now. ●Since the write-in result of My-D has returned transmission data as it is, read is required for it again.
2D-53-00001000 TAMURA CORPORATION -8/ 16 - 6-2. USB communications protocol (tag -> RFID R/W -> host) 1 2~4 5~n n+1 n+3 ENQ command parameter CRC16 EOT 0x05 The following table The following table 2bytes 0x04 CRC16 calculation Value From ENQ to EOT considers it as 1 text CRC16 : JIS X 6323-3(Part III: Refer to Collision Prevention and Transmission Protocol) ISO/IEC 13239 No command function parameter1 parameter2 parameter3 00 “R00” ROM Version XX,XX YMD Version(2) YY(1),MM(1) DD(1) ○01 “R01” Inventory DSFID(1) UID(8) ○02 “R02” Stay Quiet UID(8) ○03 “R03” N Block Read(All data) (Max=9Blocks) UID(8)*1 SBlock#(1), Block count(1) The part of the number of9Blocks(45) ○04 “R04” N Block Write(All data) ×05 “R05” Read Single Block UID(8)*1 Block#(1) Security(1), data(4) ○06 “R06” Write Single Block UID(8)*1 Block#(1) Dummy(1), data(4) ○07 “R07” Lock Block UID(8)*1 Block#(1) Security(1), data(4) ○08 “R08” Read Multi Blocks (Max=9Blocks) UID(8)*1 SBlock#(1), Block count(1) The part of the number of9Block(45) ○09 “R09” Write Multi Blocks ×10 “R10” Select Tag UID(8) ○11 “R11” Reset to Ready UID(8)*1 ○12 “R12” Write AFI Flag(1), UID(8)*1 DSFID(1), AFI(1) VICC(2), IC(1) ○13 “R13” Lock AFI UID(8)*1 ○14 “R14” Write DSFID Flag(1), UID(8)*1 DSFID(1), AFI(1) VICC(2), IC(1) ○15 “R15” Lock DSFID UID(8)*1 ○16 “R16” Get System Information Flag(1), UID(8)*1 DSFID(1), AFI(1) VICC(2), IC(1) ○17 “R17” Get Multi Block Security Status UID(8)*1 Sdata(1), data count(1) The part of the number of32Block(32) ○18 “R18” Write 2 Blocks UID(8)*1 Block#(1), 2(1) ○19 “R19” Lock 2 Blocks UID(8)*1 Block#1(1) ○20 “R99” Error return Error flag(1) Error code(1) ○ notes：S=start、Block#=01∼64 (byte count)：The number in a parenthesis It is related with an error return and is a reference of error handling. “R03” is the same as “R08” The segment which is less than the Block number of "R03", "R08", and "R17" is filled up with 0. YY＝A.D.（2000+YY） "R18 [Write 2 Blocks]" and "R19 [Lock 2 Blocks]" are Tag-it. It is original command.
2D-53-00001000 TAMURA CORPORATION -9/ 16 - No command function parameter1 parameter2 parameter3 21 22 23 “R23” 24 “R24” 25 “R25” 26 “R26” 27 “R27” 28 “R28” 29 “R29” 30 31 “R31”* Inventory DSFID(1) UID(8) ○32 “R32”* Stay Quiet UID(8) ○33 “R33”* N Block Read(All data) (Max=9Blocks) UID(8)*1 SBlock#(1), Block count(1) The part of the number of9Blocks(45) ○34 35 “R35”* Read Single Block UID(8)*1 Block#(1) Security(1) data(4) ○36 “R36”* Write Single Block UID(8)*1 Block#(1) Dummy(1), data(4) ○37 “R37”* Lock Block UID(8)*1 Block#(1) Security(1), data(4) ○38 “R38”* Read Multi Blocks (Max=9Blocks) UID(8)*1 SBlock#(1), Block count(1) The part of the number of9Blocks(45) ○39 40 “R40”* Select Tag UID(8) ○41 “R41”* Reset to Ready UID(8)*1 ○42 “R42”* Write AFI Flag(1), UID(8)*1 DSFID(1), AFI(1) VICC(2), IC(1) ×43 “R43”* Lock AFI UID(8)*1 ×44 “R44”* Write DSFID Flag(1), UID(8)*1 DSFID(1) AFI(1) VICC(2), IC(1) ×45 “R45”* Lock DSFID UID(8)*1 ×46 “R46”* Get System Information Flag(1), UID(8)*1 DSFID(1), AFI(1) VICC(2), IC(1) ×47 “R47”* 48 “R48”* 49 “R49”* 50 ●* is command of a My-D card. ●My-D assumes 124Page (248Block) with the architecture of 4 bytes/Block now. ●Since the write-in result of My-D has returned transmission data as it is, read is required for it again.
2D-53-00001000 TAMURA CORPORATION -10/ 16 - 6-3．Error handling It consists of 2bytes of the error flag/error code. The 1st byte : =0 → It is an error flag on a processing. The 2nd byte is an error code. The 1st byte : ≠0 → It is an error flag on a standards. The 2nd byte is an error code. receive data 1 2 3 4 5 6 7 8 9 ENQ R 9 9 Error flag Error code CRC16(L) CRC16(H) EOT flag=0 → code = 1 : The error under processing of Tag-it → code = 2 : A processing of Tag-it times out. flag≠0 → : JIS X 6323-3 Refer to (ISO/IEC 15693-3) : Tag-it HF-I Transponder Inlay Extended Commands and Options
2D-53-00001000 TAMURA CORPORATION -11/ 16 - 7. Attention (1) After a command transmission, please put "WAIT" and read a response. (2) Since an error may return depend on PC (personal computer) used, please add a retry processing. (3) This product assumes 1 block to be 4 bytes. my-d corresponds as follows, although 1 block has 8-byte composition. The 1-4 blocks of my-d cannot be read and written. (4)The error flag and error code at the time of setting the parameter which exceeded the block span by [N Block Read] [Read Multi Block] [Get Multi Block Security Status] are variable depend on the category of tag and parameter. (5) When a command is sent to tag in "Select status", the first byte "E0" in the UID parameter should be changed to "10"
2D-53-00001000 TAMURA CORPORATION -12/ 16 - (6) Any error code is not returned if it performs the [Write AFI] processing to the I-CODE2 tag AFI locked. (7) Any error code is not returned if it performs the [Lock AFI] processing to the I-CODE2 tag AFI locked. (8) Any error code is not returned if it performs the [Write DSFID ] processing to the I-CODE2 tag DSFID locked. (9) Any error code is not returned if it performs the [Lock DSFID ] processing to the I-CODE2 tag DSFID locked. (10) When you perform "Read" and "Write", without setting up UID in particular, please perform a single byte set of an implementation-supplier code. (11) An error occurs when 29 or more blocks are set to I-CODE2 with single byte setting as an implementation-supplier code. (12) This product performs with to the following tag or the tag in which IC was used. TAG-IT HFI [TEXAS INSTRUMENTS] I-CODE2 SL2 ICS20 [PHILIPS] my-d SRF 55V10P [Infineon Technologies]
2D-53-00001000 TAMURA CORPORATION -13/ 16 - 8. Product specification 8-1．Interface specification (1)USB interface (1-1)Connector (1-2) Standard USB1.1 Low Speed (2)External antenna interface The miniaturized antenna is built in this product. It is prohibition to connect an external antenna. 8-2．Mechanical specification Weight : 20g or less Pin No. function Signal 1 Vbus +5V 2 D- Serial data(-) 3 D+ Serial data(+) 4 GND GND ①④
2D-53-00001000 TAMURA CORPORATION -14/ 16 - 8-3.General specification Radio Frequency : 13.56MHz Correspondence standard : ISO15693 Voltage of operation : +4.75V ~ +5.25V Consumption current : 100mA or less LED(green) : Power-up lighting LED(red) : Blink at the time of a datacomm with a tag. Operating temperature : 0°C~+40°C (+32°F~+104°F) Operating humidity : 20~80%RH (non-condensation) Storage temperature : -20°C~60°C (-4°F~+140°F) Storage humidity : 10~90%RH (non-condensation)
2D-53-00001000 TAMURA CORPORATION -15/ 16 - 9．Guarantee 【About guarantee】 This guarantee promises a gratis repair, when the product I was allowed to supply should be broken down by the normal activity according to this product specification. 【Term of a guarantee】 Three months after the delivery. 【Inapplicable guarantee】 Even if it is within the term of a guarantee, when it corresponds to the following list item, it becomes inapplicable gratis repair . (1) The damage or the trouble by the handling from which it deviated by the written content of the " attention ." (2) Damage by the natural disaster of a thunderbolt, a Fire, storm and flood damages, an earthquake, and others and pollution, damage from salt water, a static electricity, etc. (3) The trouble resulting from other connected units and other external factors. (4) Externally caused injury of the main frame after a Delivery. (5) When an event is NOT reproduced at TAMURA Corporation. 【Other attention】 (1) When the damage which is contrary to the "attention" written content of this product, and originates in a user's intentionally and negligence occurs, TAMURA Corporation DOES NOT take the responsibility. (2) When the damage concerning direct and the indirect target resulting from an activity of this product occurs, the responsibility is NOT taken except for the case where there is negligence in which TAMURA Corporation is serious. (3) Guarantee is effective only in an application country.
2D-53-00001000 TAMURA CORPORATION -16/ 16 - 10．Model specification 10-1．Specification number (Japan) The model specification of TMRF-1-U001-KM is as follows. 10-2. Wireless Telegraph Law Since the following acts serve as a fault of Wireless Telegraph Law, please do not perform them by any means. (1) Use an external antenna. (2) Convert this product. 11. Reference Tamura Corporation Broadcom B.U. 1-19-43, Higashi-Oizumi, Nerima-ku, Tokyo, 178-8511 Japan URL:http://www.tamura-ss.co.jp Model name Attestation numberTM-RFRW-U001 AC-04097

Navigation menu