Taylor Refrigerator C713 Users Manual

C713 to the manual c366bf7b-dd05-4737-8313-02f5310faef7

2015-02-02

: Taylor Taylor-Taylor-Refrigerator-C713-Users-Manual-449453 taylor-taylor-refrigerator-c713-users-manual-449453 taylor pdf

Open the PDF directly: View PDF .
Page Count: 50

Download
Open PDF In Browser	View PDF

OPERATOR'S
MANUAL

Model C713
Soft Serve Freezer

Original Operating Instructions
062180-M
2/11/05 (Original Publication)
(Updated 8/26/14)

Complete this page for quick reference when service is required:
Taylor Distributor:
Address:
Phone:
Service:
Parts:
Date of Installation:

Information found on the data label:
Model Number:
Serial Number:
Electrical Specs:

Voltage

Cycle

Phase
Maximum Fuse Size:

Minimum Wire Ampacity:

E 2005 Carrier Commercial Refrigeration, Inc.
062180- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work
may be a violation of Copyright Law of the United States of America and other countries, could result in the
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further
civil and criminal penalties. All rights reserved.

Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072

Table of Contents
Section 1

To the Installer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Installer Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Site Preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Air Cooled Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Water Connections (Water Cooled Units Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Electrical Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Beater Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Refrigerant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 2

To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 3

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 4

Operator Parts Identification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model C713 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model C713 Door and Beater Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brushes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 5

Important: To the Operator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Symbol Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operating Screen Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manager's Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 6

Operating Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Freezing Cylinder Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Manual Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Draining Product From The Freezing Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Model C713

Table of Contents

Table of Contents - Page 2
Rinsing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Hopper Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Disassembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Brush Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 7

Important: Operator Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

During Cleaning and Sanitizing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Troubleshooting Bacterial Count . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Regular Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Winter Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 8

Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 9

Parts Replacement Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 10

Limited Warranty on Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Section 11

Limited Warranty on Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Wiring Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Note: Continuing research results in steady improvements; therefore, information
in this manual is subject to change without notice.
Note: Only instructions originating from the factory or its authorized translation
representative(s) are considered to be the original set of instructions.
E 2005 Carrier Commercial Refrigeration, Inc. (Original Publication)
(Updated August, 2014)
062180- M
Any unauthorized reproduction, disclosure, or distribution of copies by any person of any portion of this work
may be a violation of Copyright Law of the United States of America and other countries, could result in the
awarding of Statutory Damages of up to $250,000 (17 USC 504) for infringement, and may result in further
civil and criminal penalties. All rights reserved.

Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072

Table of Contents

Model C713

Section 1

To the Installer

The following information has been included in the
manual as safety and regulatory guidelines. For
complete installation instructions, please see the
Installation Checklist.

This unit has many sharp edges that can
cause severe injuries.

Site Preparation
Installer Safety

Review the area the unit is to be installed in before
uncrating the unit making sure that all possible
hazards the user or equipment may come into have
been addressed.

In all areas of the world, equipment should
be installed in accordance with existing local codes.
Please contact your local authorities if you have any
questions.

Air Cooled Units
The Model C713 air cooled unit requires a minimum
of 3” (76 mm) of clearance on all sides. Install the
deflector provided to prevent recirculation of warm
air. This will allow for adequate air flow across the
condenser. Failure to allow adequate clearance can
reduce the refrigeration capacity of the freezer and
possibly cause permanent damage to the
compressor.

Care should be taken to ensure that all basic safety
practices are followed during the installation and
servicing activities related to the installation and
service of Taylor equipment.

Only authorized Taylor service personnel
should perform installation and repairs on
the equipment.
Authorized service personnel should consult
OSHA Standard 29CFRI910.147 or the
applicable code of the local area for the
industry standards on lockout/tagout
procedures before beginning any installation
or repairs.
Authorized service personnel must ensure
that the proper PPE is available and worn
when required during installation and
service.
Authorized service personnel must remove
all metal jewelry, rings, and watches before
working on electrical equipment.

This unit must NOT be installed in an area
where a water jet or hose can be used. NEVER use
a water jet or hose to rinse or clean the unit. Failure
to follow this instruction may result in electrocution.

This unit must be installed on a level surface
to avoid the hazard of tipping. Extreme care should
be taken in moving this equipment for any reason.
Two or more persons are required to safely move
this unit. Failure to comply may result in personal
injury or equipment damage.

The main power supply(s) to the freezer
must be disconnected prior to performing any
repairs. Failure to follow this instruction may result in
personal injury or death from electrical shock or
hazardous moving parts as well as poor
performance or damage to the equipment.

Uncrate the unit and inspect it for damage. Report
any damage to your Taylor Distributor.
This piece of equipment is made in the USA and has
USA sizes of hardware. All metric conversions are
approximate and vary in size.

Note: All repairs must be performed by an
authorized Taylor Service Technician.

131121

Model C713

To the Installer

Water Connections
(Water Cooled Units Only)
CAUTION: THIS EQUIPMENT MUST BE
PROPERLY GROUNDED! FAILURE TO DO SO
CAN RESULT IN SEVERE PERSONAL INJURY
FROM ELECTRICAL SHOCK!

An adequate cold water supply must be provided
with a hand shut-off valve. On the underside of the
base pan or on the right side, two 3/8” I.P.S. water
connections for inlet and outlet are provided for easy
hook-up. 1/2” inside diameter water lines should be
connected to the machine. (Flexible lines are
recommended, if local codes permit.) Depending on
local water conditions, it may be advisable to install
a water strainer to prevent foreign substances from
clogging the automatic water valve. There will be
only one water “in” and one water “out” connection.
DO NOT install a hand shut-off valve on the water
“out” line! Water should always flow in this order:
first, through the automatic water valve; second,
through the condenser; and third, through the outlet
fitting to an open trap drain.

DO NOT operate this freezer with larger
fuses than specified on the unit data label. Failure to
follow this instruction may result in electrocution or
damage to the machine.

This unit is provided with an equipotential
grounding lug that is to be properly attached to the
rear of the frame by the authorized installer. The
installation location is marked by the equipotential
bonding symbol (5021 of IEC 60417-1) on both the
removable panel and the equipments frame.

A back flow prevention device is
required on the incoming water connection side.
Please refer to the applicable National, State, and
local codes for determining the proper configuration.

Stationary appliances which are not
equipped with a power cord and a plug or another
device to disconnect the appliance from the power
source must have an all-pole disconnecting device
with a contact gap of at least 3mm installed in the
external installation.

Electrical Connections
In the United States, this equipment is intended to
be installed in accordance with the National
Electrical Code (NEC), ANSI/NFPA 70-1987. The
purpose of the NEC code is the practical
safeguarding of persons and property from hazards
arising from the use of electricity. This code contains
provisions considered necessary for safety. In all
other areas of the world, equipment should be
installed in accordance with the existing local codes.
Please contact your local authorities.

Appliances that are permanently connected
to fixed wiring and for which leakage currents may
exceed 10 mA, particularly when disconnected or
not used for long periods, or during initial installation,
shall have protective devices such as a GFI, to
protect against the leakage of current, installed by
the authorized personnel to the local codes.

Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not lighter than
ordinary polychloroprene or other equivalent
synthetic elastomer-sheathed cord (Code
designation 60245 IEC 57) installed with the proper
cord anchorage to relieve conductors from strain,
including twisting, at the terminals and protect the
insulation of the conductors from abrasion.

FOLLOW YOUR LOCAL ELECTRICAL CODES!

Each unit requires one power supply for each data
label on the unit. Check the data label(s) on the
freezer for branch circuit overcurrent protection or
fuse, circuit ampacity, and other electrical
specifications. Refer to the wiring diagram provided
inside of the electrical box for proper power
connections.

If the supply cord is damaged, it must be replaced
by the manufacturer, its service agent, or similarly
qualified person, in order to avoid a hazard.

130318

To the Installer

Model C713

Beater Rotation
Use only R404A refrigerant that conforms
to the AHRI standard 700 specification. The use of
any other refrigerant may expose users and
operators to unexpected safety hazards.

Beater rotation must be clockwise as viewed
looking into the freezing cylinder.
Note: The following procedures should be performed
by a trained service technician.
To correct the rotation on a three-phase unit,
interchange any two incoming power supply lines at
freezer main terminal block only.

Refrigerant liquid sprayed onto the skin may
cause serious damage to tissue. Keep eyes and skin
protected. If refrigerant burns should occur, flush
immediately with cold water. If burns are severe,
apply ice packs and contact a physician
immediately.

To correct rotation on a single-phase unit, change
the leads inside the beater motor. (Follow the
diagram printed on the motor.)
Electrical connections are made directly to the
terminal block provided in the splice box.

Taylor reminds technicians to be cautious of
government laws regarding refrigerant recovery,
recycling, and reclaiming systems. If you have any
questions regarding these laws, please contact the
factory Service Department.

Refrigerant

In consideration of our environment, Taylor
proudly uses only earth friendly HFC refrigerants.
The HFC refrigerant used in this unit is R404A. This
refrigerant is generally considered non-toxic and
non-flammable, with an Ozone Depleting Potential
(ODP) of zero (0).

WARNING: R404A refrigerant used in
conjunction with polyolester oils is extremely
moisture absorbent. When opening a refrigeration
system, the maximum time the system is open must
not exceed 15 minutes. Cap all open tubing to
prevent humid air or water from being absorbed by
the oil.

However, any gas under pressure is potentially
hazardous and must be handled with caution.
NEVER fill any refrigerant cylinder completely with
liquid. Filling the cylinder to approximately 80% will
allow for normal expansion.

130930

Model C713

To the Installer

Section 2

To the Operator

Your freezer has been carefully engineered and
manufactured to give you dependable operation.

similar legislation in effect after August 13, 2005.
Therefore, it must be collected separately after its
use is completed, and cannot be disposed as
unsorted municipal waste.

This unit, when properly operated and cared for, will
produce a consistent quality product. Like all
mechanical products, it will require cleaning and
maintenance. A minimum amount of care and
attention is necessary if the operating procedures
outlined in this manual are followed closely.

The user is responsible for returning the product to
the appropriate collection facility, as specified by
your local code.
For additional information regarding applicable local
laws, please contact the municipal facility and/or
local distributor.

This Operator's Manual should be read before
operating or performing any maintenance on your
equipment.

Compressor Warranty Disclaimer

Your Taylor freezer will NOT eventually compensate
for and correct any errors during the set-up or filling
operations. Thus, the initial assembly and priming
procedures are of extreme importance. It is strongly
recommended that personnel responsible for the
equipment's operation, both assembly and
disassembly, go through these procedures together
in order to be properly trained and to make sure that
no confusion exists.

The refrigeration compressor(s) on this unit are
warranted for the term stated in the Limited
Warranty section in this manual. However, due to
the Montreal Protocol and the U.S. Clean Air Act
Amendments of 1990, many new refrigerants are
being tested and developed, thus seeking their way
into the service industry. Some of these new
refrigerants are being advertised as drop-in
replacements for numerous applications. It should
be noted that in the event of ordinary service to this
unit's refrigeration system, only the refrigerant
specified on the affixed data label should be
used. The unauthorized use of alternate refrigerants
will void your Taylor compressor warranty. It is the
unit owner's responsibility to make this fact known to
any technician he employs.

In the event you should require technical assistance,
please contact your local authorized Taylor
Distributor.
Note: Your Taylor warranty is valid only if the parts
are authorized Taylor parts, purchased from the
local authorized Taylor Distributor, and only if all
required service work is provided by an authorized
Taylor service technician. Taylor reserves the right
to deny warranty claims on units or parts if
non-Taylor approved parts or incorrect refrigerant
were installed in the unit, system modifications were
performed beyond factory recommendations, or it is
determined that the failure was caused by abuse,
misuse, neglect, or failure to follow all operating
instructions. For full details of your Taylor Warranty,
please see the Limited Warranty section in this
manual.

It should also be noted that Taylor does not warrant
the refrigerant used in its equipment. For example, if
the refrigerant is lost during the course of ordinary
service to this machine, Taylor has no obligation to
either supply or provide its replacement either at
billable or unbillable terms. Taylor does have the
obligation to recommend a suitable replacement if
the original refrigerant is banned, obsoleted, or no
longer available during the five year warranty of the
compressor.
Taylor will continue to monitor the industry and test
new alternates as they are being developed. Should
a new alternate prove, through our testing, that it
would be accepted as a drop-in replacement, then
the above disclaimer would become null and void.
To find out the current status of an alternate
refrigerant as it relates to your compressor warranty,
call the local Taylor Distributor or the Taylor Factory.
Be prepared to provide the Model/Serial Number of
the unit in question.

Note: Constant research results in steady
improvements; therefore, information in this
manual is subject to change without notice.

If the crossed out wheeled bin symbol is
affixed to this product, it signifies that this product is
compliant with the EU Directive as well as other
131121

To the Operator

Model C713

Section 3

Safety

We, at Taylor Company, are concerned about the
safety of the operator when he or she comes in
contact with the freezer and its parts. Taylor has
gone to extreme efforts to design and manufacture
built-in safety features to protect both you and the
service technician. As an example, warning labels
have been attached to the freezer to further point
out safety precautions to the operator.

S
S
S
S

To Operate Safely:
S
IMPORTANT - Failure to adhere to the
following safety precautions may result in
severe personal injury or death. Failure to
comply with these warnings may damage the
machine and its components. Component
damage will result in part replacement expense
and service repair expense.

S
DO NOT operate the freezer without
reading this Operator Manual. Failure to follow this
instruction may result in equipment damage, poor
freezer performance, health hazards, or personal
injury.

This appliance is to be used only by trained
personnel. It is not intended for use by children or
people with reduced physical, sensory, or mental
capabilities, or lack of experience and knowledge,
unless given supervision or instruction concerning
the use of the appliance by a person responsible for
their safety. Children should be supervised to ensure
that they do not play with the appliance.

DO NOT operate the freezer unless it is
properly grounded.
DO NOT operate freezer with larger fuses
than specified on the data label.
All repairs must be performed by an
authorized Taylor service technician.
The main power supplies to the machine
must be disconnected prior to performing
any repairs.
For Cord Connected Units: Only Taylor
authorized service technicians or licensed
electricians may install a plug or
replacement cord on these units.
Stationary appliances which are not
equipped with a power cord and a plug or
another device to disconnect the appliance
from the power source must have an all-pole
disconnecting device with a contact gap of
at least 3 mm installed in the external
installation.
Appliances that are permanently connected
to fixed wiring and for which leakage
currents may exceed 10 mA, particularly
when disconnected or not used for long
periods, or during initial installation, shall
have protective devices such as a GFI, to
protect against the leakage of current,
installed by the authorized personnel to the
local codes.
Supply cords used with this unit shall be
oil-resistant, sheathed flexible cable not
lighter than ordinary polychloroprene or
other equivalent synthetic
elastomer-sheathed cord (Code designation
60245 IEC 57) installed with the proper cord
anchorage to relieve conductors from strain,
including twisting, at the terminals and
protect the insulation of the conductors from
abrasion.
If the supply cord is damaged, it must be
replaced by the manufacturer, its service
agent, or similarly qualified person, in order
to avoid a hazard.

Failure to follow these instructions may result in
electrocution. Contact your local authorized Taylor
Distributor for service.

130213

Model C713

Safety

DO NOT use a water jet to clean or rinse
the freezer. Failure to follow these instructions may
result in serious electrical shock.

S
S
S

This freezer must be placed on a level
surface. Failure to comply may result in personal
injury or equipment damage.

Cleaning and sanitizing schedules are
governed by your state or local regulatory agencies
and must be followed accordingly. Please refer to
the cleaning section of this manual for the proper
procedure to clean this unit.

DO NOT allow untrained personnel to
operate this machine.
DO NOT operate the freezer unless all
service panels and access doors are
restrained with screws.
DO NOT remove any internal operating
parts (examples: freezer door, beater,
scraper blades, etc.) unless all control
switches are in the OFF position.

This machine is designed to maintain
product temperature under 41°F (5°C). Any product
being added to this machine must be below 41°F
(5°C). Failure to follow this instruction may result in
health hazards and poor freezer performance.

Failure to follow these instructions may result in
severe personal injury to fingers or hands from
hazardous moving parts.

DO NOT obstruct air intake and discharge openings:

This unit has many sharp edges that can
cause severe injuries.

S
S

A minimum of 3” (76 mm) air space is required on all
sides. Install the deflector provided to prevent
recirculation of warm air. Failure to follow this
instruction may cause poor freezer performance and
damage to the machine.

DO NOT put objects or fingers in the door
spout. This may contaminate the product
and cause severe personal injury from blade
contact.
USE EXTREME CAUTION when removing
the beater asssembly. The scraper blades
are very sharp.
CAUTION-SHARP EDGES: Two people are
required to handle the cup/cone dispenser.
Protective gloves must be worn and the
mounting holes must NOT be used to lift or
hold the dispenser. Failure to follow this
instruction can result in personal injury to
fingers or equipment damage.

For Indoor Use Only: This unit is designed to
operate indoors, under normal ambient
temperatures of 70_ - 75_F (21_ - 24_C). The
freezer has successfully performed in high ambient
temperatures of 104_(40_C) at reduced capacities.
DO NOT run the machine without product. Failure to
follow this instruction can result in damage to the
machine.

Access to the service area of the unit is
restricted to persons having knowledge and practical
experience with the appliance, in particular as far as
safety and hygiene are concerned.

NOISE LEVEL: Airborne noise emission does not
exceed 78 dB(A) when measured at a distance of
1.0 meter from the surface of the machine and at a
height of 1.6 meters from the floor.

130318

Safety

Model C713

Notes:

Model C713

Safety

Section 4

Operator Parts Identification

Model C713

Figure 1
121005

Operator Parts Identification

Model C713

C713 Exploded View Parts Identification

ITEM

DESCRIPTION

PART NO.

ITEM

DESCRIPTION

PART NO.

COVER-HOPPER

053809-1

SCREW-1/4-20 X 3/8 RHM-SS

011694

ORIFICE

022465-100

063087

O-RING-3/8 OD X ..070 W

016137

PANEL-CORNER-FRONT
RIGHT

TUBE A.-FEED-SS 5/32 HOLE

X29429-2

CASTER-4” SWV 3/4-10 STEM
W/BRAKE

046437

O-RING-.643 OD X .077 W

018572

DEFLECTOR-BLOWER

047912

PANEL-REAR

059917

SHIELD-SPLASH-WIRE-19-3/4 L 033813

PANEL-SIDE*RIGHT

059907

PANEL A.-FRONT LOWER

X59854-SER

PAN-DRIP 12.5

059736

TRAY-DRIP-19-5/8 L X 4-7/8

033812

PANEL A.-FRONT

X63879

PAN-DRIP 19-1/2 LONG

035034

PANEL A.-FRONT

X59836

PANEL-CORNER-FRONT LEFT

063088

STUD-NOSE CONE

055987

PANEL-SIDE LEFT

059906

FILTER-AIR-POLY-FLO

052779-11

FASTENER-DOOR LATCH

030787

PANEL A.-FILTER-LOUVERED

X59928

FASTENER-DOOR STRIKE

030788

CASTER-4” SWV 3/4-10 STEM

044106

121005

Model C713

Operator Parts Identification

Model C713 Door and Beater Assembly

Figure 2
ITEM

DESCRIPTION

PART NO.

ITEM

DESCRIPTION

PART NO.

HANDLE A.-DRAW-WELDED

X56421-1

CAP-DESIGN 1.010" ID - 6 PT

014218

O-RING-1/4 OD X .070W 50

015872

SEAL-DRAW VALVE

034698

SCREW-ADJUSTMENT-5/16-24

056332

O-RING-7/8 OD X .103 W

014402

PLUG-PRIME TWIN

059936

PIN-HANDLE-TWIN

059894

O-RING-1/2 OD X 0.70 W

024278

GASKET-DOOR HT 4"-DOUBLE

048926

NUT-STUD-BLACK 3.250 LONG

058765

BEARING-FRONT

050216

NUT-STUD-BLACK 2.563 LONG

058764

BLADE-SCRAPER-PLASTIC 17L

035174

DOOR A.-3SPT*LG BAF*W/PRG

X59922

BEATER A.-3.4QT-HELICORE

X31761

VALVE A.-DRAW

X59843

SHAFT-BEATER

032564

VALVE A.-DRAW CENTER

X62218

SEAL-DRIVE SHAFT

032560

081008

Operator Parts Identification

Model C713

Accessories

Figure 3
ITEM

DESCRIPTION

PART NO.

ITEM

DESCRIPTION

PART NO.

LUBRICANT-TAYLOR

047518

SANITIZER-STERA SHEEN

SEE NOTE

TOOL-O-RING REMOVAL

048260-WHT

KIT A.-TUNE-UP

X49463-80

PAIL-10 QT

013163

* Not Shown
Note: A sample container of sanitizer is sent with the
unit. For reorders, order Stera Sheen part no. 055492
(100 2 oz. packs) or Kay-5 part no. 041082 (200 packs).

140721

Model C713

Operator Parts Identification

Brushes

Figure 4
ITEM

DESCRIPTION

PART NO.

ITEM

DESCRIPTION

PART NO.

BLACK BRISTLE BRUSH

013071

BRUSH-END-DOOR SPOUT SS

039719

DOUBLE END BRUSH

013072

BRUSH-SET LVB

050103

WHITE BRISTLE BRUSH
(1” x 2”)

013073

BRUSH-PUMP SPOUT

054068

WHITE BRISTLE BRUSH
(3” x 7”)

023316

Operator Parts Identification

Model C713

Section 5

Important: To the Operator

Figure 5
ITEM

DESCRIPTION

ITEM

DESCRIPTION

POWER SWITCH

SELECT KEY

LIQUID CRYSTAL DISPLAY

SERVICE MENU KEY

KEYPADS

BRUSH CLEAN COUNTER

MIX OUT INDICATOR

ARROW KEYS

STANDBY KEY

TOPPING HEATER KEYS

MIX LOW INDICATOR

130213

Model C713

Important: To the Operator

Symbol Definitions

= TOPPING HEATER-LEFT

To better communicate in the International arena,
symbols have replaced words on many of our
operator switches, function, and fault indicators.
Your Taylor equipment is designed with these
International symbols.

= TOPPING HEATER-RIGHT

Power Switch

The following chart identifies the symbol definitions.

When placed in the ON position, the power switch
allows control panel operation.
= SELECT

Fluorescent Display
The fluorescent display is located on the front
control panel. During normal operation the display is
blank. The display is used to show menu options
and notifies the operator if a fault is detected. On
International models, the display will indicate the
temperature of the mix in the hopper.

= ON

= OFF

Indicator Lights
= UP ARROW

MIX LOW - When the MIX LOW symbol
is
illuminated, the mix hopper has a low supply of mix
and should be refilled as soon as possible.

= DOWN ARROW

symbol is
MIX OUT - When the MIX OUT
illuminated, the mix hopper has been almost
completely exhausted and has an insufficient supply
of mix to operate the freezer. At this time, the AUTO
mode is locked out and the freezer will be placed in
the STANDBY mode. To initiate the refrigeration
system, add mix to the mix hopper and touch the

= AUTO

AUTO symbol . The freezer will automatically
begin operation.

= WASH

Standby Symbol
= MIX LOW

During long “No Sale” periods, the unit can be
placed into the Standby mode. This maintains
product temperatures below 40°F (4.4°C) in both the
hopper and the freezing cylinder, and helps prevent
overbeating and product breakdown.

= MIX OUT

Using clean, sanitized hands, remove the air orifice.
Lubricate the o-rings located on the end of the feed
tube without the hole. Place that end of the tube into
the mix inlet hole. When STANDBY is selected, the

= MENU DISPLAY

illuminates, indicating the
STANDBY symbol
Standby feature has been activated.

= STANDBY

IMPORTANT: Make sure the level of mix in the
hopper is below the mix inlet hole in the feed

130626

Important: To the Operator

Model C713

tube. Failure to follow this instruction may result in
lower product quality when normal operation is
resumed.

Feed Tube
The feed tube serves two purposes. One end of the
tube has a hole and the other end does not. The air
orifice maintains overrun and allows enough mix to
enter the freezing cylinder after a draw.

To resume normal operation, press the AUTO
symbol . When the unit cycles off, the product in
the freezing cylinder will be at serving viscosity. At
this time, turn the feed over. Place the end of the
tube with the hole into the mix inlet hole. Install the
air orifice.

Wash Symbol
The WASH symbol
will illuminate when it is
touched. This indicates beater motor operation. The
STANDBY or AUTO modes must be cancelled first
to activate the WASH mode.

Auto Symbol

Figure 6
1.

The AUTO symbol
will illuminate when it is
touched. This indicates that the refrigeration system
has been activated. In the AUTO mode, the WASH
or STANDBY functions are automatically cancelled.

During normal operation, the end of the feed
tube with the hole is placed into the mix inlet
hole. Every time the draw handle is raised, new
mix and air from the hopper flow into the
freezing cylinder. This keeps the freezing
cylinder properly loaded and maintains overrun.

Note: An indicating light and an audible tone will
sound whenever a mode of operation has been
selected. To cancel any function, touch the key
again. The light and the mode of operation will shut
off.

The reset buttons are located in the back panel of
the machine. It protects the beater motor from an
overload condition. Should an overload occur, the
reset mechanism will trip. To properly reset the
freezer place the power switch in the OFF position.
Press the reset button firmly. Turn the power switch
and

IMPORTANT: Make sure the level of mix in
the hopper is below the mix inlet hole in the
feed tube. Failure to follow this instruction may
result in lower product quality when normal
operation is resumed.

WARNING: Do not use metal objects
to press the reset button. Failure to comply may
result in severe personal injury or death.

To resume normal operation, press the AUTO
symbol . When the unit cycles off, the
product in the freezing cylinder will be at
serving viscosity. At this time, turn the feed
over. Place the end of the tube with the hole
into the mix inlet hole. Install the air orifice. The
air orifice is used to meter a certain amount of
air into the freezing cylinder.

If the beater motor is turning properly, touch the
WASH symbol

Long “No Sale” Periods
During long “No Sale” periods, the unit can be
placed into the Standby mode. This maintains
product temperatures below 40°F (4.4°C) in
both the hopper and the freezing cylinder, and
helps prevent overbeating and product
breakdown. To activate STANDBY, enter the
access code for the Manager Menu (see
page 17.) Remove the air orifice. Lubricate the
o-rings located on the end of the feed tube
without the hole. Place that end of the tube into
the mix inlet hole.

Reset Mechanism

to the ON position. Touch the WASH symbol
observe the freezer's performance.

Normal Operation

to cancel the cycle. Touch the

AUTO symbol
to resume normal operation. If the
freezer shuts down again, contact your authorized
service technician.

130626

Model C713

Important: To the Operator

Adjustable Draw Handle
NVRAM FAULT
RESET TO DEFAULTS
PRESS SEL KEY

This unit features an adjustable draw handle to
provide the best portion control, giving a better,
consistent quality to your product and controlling
costs. The draw handle should be adjusted to
provide a flow rate of 5 to 7-1/2 oz. (142 to 213 g.)
of product by weight per 10 seconds. To INCREASE
the flow rate, tighten the screw. To DECREASE the
flow rate, loosen the screw. (See Figure 7.)

Figure 8
See “NVRAM FAULT” for instructions if the above
message appears on the screen.
Once the system has initialized, the number of days
remaining before the next required brush cleaning is
indicated on the control panel and the SAFETY
TIMEOUT screen is displayed with the alarm turned
on. (See Figure 9.)

SAFETY TIMEOUT
ANY KEY ABORTS

Figure 9
The SAFETY TIMEOUT screen will be displayed
with the alarm on, for 60 seconds or until any control
symbol is selected.

Figure 7

After the safety timeout has been completed and the
power switch is OFF, the following screen is
displayed. (See Figure 10.)

Operating Screen Descriptions

POWER SWITCH OFF
-=-=-=-=-=UNIT CLEANED

The fluorescent display located in the center of the
control panel is normally blank during the daily
operation of the machine. The display is activated
when the SEL symbol or the Manager's Menu is
selected. The display screen will also alert the
operator of specific faults detected by the control.

Figure 10

Power Up

Power Switch ON

When the machine is powered the control system
will initialize to perform a system check. The screen
will display “INITIALIZING”. There will be four types
of data the system will check: LANGUAGE,
SYSTEM DATA, CONFIG DATA, and LOCKOUT
DATA.

When the power switch is placed in the ON position,
the control panel touch keys become operative. The
fluorescent display will be either blank or indicate
that the unit has been cleaned. (See Figure 11.)

During the INITIALIZING... LANGUAGE screen, the
alarm will be on. If the system detects corrupt data
during INITIALIZING, the following display will alert
the operator that the control settings may have been
changed (See Figure 8.)

Important: To the Operator

UNIT CLEANED

Figure 11

Model C713

Brush Clean Counter

Entering Access Code

The Brush Clean Counter (item 9 on page 13) will
display the number of hours since the freezer was
last brush cleaned. After hour 99, it will change to a
letter and a number (example: A0, A1. . B0, B1, etc.)

With the ACCESS CODE screen on the display use
the SEL symbol to set the first code number in the
cursor position. When the correct number is
selected, touch the SEL symbol to move the cursor
to the next number position. (See Figure 13.)

Manager's Menu
The Manager's Menu is used to enter the operator
function displays. To access the Menu, touch the

ENTER ACCESS CODE
8
__

on the control panel.
center of the CONE symbol
The arrow symbols, the SEL symbol and the CONE

will be lit when the ACCESS CODE
symbol
screen is displayed. (See Figure 12.)
Figure 13
Continue to enter the proper access code numbers
(8309) until all four numbers are displayed, then
touch the SEL symbol. The Manager's menu list will
display on the screen provided the correct access
code is entered.
If an incorrect number is entered for the access
code, the display will exit the Menu program when
the SEL symbol is selected. (See Figure 14.)
Figure 12
In the Menu program, the arrow symbols and the
SEL symbol will function as menu keys.
UP ARROW - increases the value above the cursor
and is used to scroll upward in text displays.
DOWN ARROW - decreases the value above the
cursor and is used to scroll downward in text
displays.
SEL - advances the cursor position to the right and
is used to select menu options.
Note: The machine will continue operation in the
mode it was in when the menu was selected.
However, the control keys will not be lit and are
non-functional when the Manager's Menu is
displayed.

Model C713

Figure 14

Important: To the Operator

Reset the SERVING COUNTER by selecting the
SEL symbol to advance to the next screen. Select
the UP arrow symbol to move the arrow (>) to YES
and select the SEL symbol. The servings counter
will reset to zero and exit back to the Manager's
Menu. (See Figure 16.)

Menu Options
Touch the ARROW symbols to move up or down
through the Menu. Select a Menu option by touching
the SEL symbol. Exit the Menu program by selecting
EXIT FROM MENU or touch the CONE symbol

.
RESET DRAW COUNTER

The following menu options are listed in the
Manager's Menu.
>

EXIT FROM MENU
RESET DRAW COUNTER
SET CLOCK
AUTO START TIME
STANDBY MODE
MIX LEVEL AUDIBLE
LOCKOUT HISTORY
SYSTEM INFORMATION

Figure 16
The SET CLOCK option allows the Manager to
adjust the control clock date and time. The date and
time may only be changed after the freezer has
been manually cleaned but before it has been
placed in the AUTO or STANDBY mode. The
following message will be displayed if the SET
CLOCK option is selected when the machine is not
in a brush clean state. (See Figure 17.)
SET CLOCK
12:01

7/15/2004
NO CHANGES ALLOWED
Press Any Key

Selecting “EXIT FROM MENU” will exit the
Manager's Menu and the return the control panel
symbols to normal operation.
The SERVING COUNTER screen is used to check
or reset the number of servings dispensed from the
machine. The SERVING COUNTER will
automatically reset to zero when the machine is
brush cleaned. (See Figure 15.)

Figure 17
To change the date or time, select the SET CLOCK
option in the menu. Touch the UP arrow symbol to
advance the arrow from Exit to Change, then touch
the SEL symbol to select the Change option.
(See Figure 18.)

SERVINGS COUNTER
0

YES
NO

SET CLOCK
12:01
Change
> Exit

> Next

Figure 15

7/15/2004

Figure 18

050722

Important: To the Operator

Model C713

Enable the AUTO START TIME by selecting the UP
arrow symbol to move the arrow up to Enable.
Touch the SEL symbol to advance to the next
screen. (See Figure 22.)

Change the time by touching the UP arrow with the
cursor under the hour position. Move the cursor to
the minutes by touching the SEL symbol. Once the
correct minutes are entered, touch the SEL symbol
to advance the cursor to the month. (See Figure 19.)

SET CLOCK
12:01

7/15/2004

AUTO START TIME
00:00
Change
Exit

> Exit

Figure 22
Figure 19

Program the AUTO START TIME by selecting the
UP arrow symbol to move the arrow to Change.
Touch the SEL symbol to advance to the next
screen. (See Figure 23.)

Enter the correct month, day, and year. Then touch
the SEL symbol to advance to the DAYLIGHT
SAVING TIME screen. (See Figure 20.)

AUTO START TIME
00:00

DAYLIGHT SAVING TIME
ENABLED
Enable
Disable

Figure 23
Figure 20

Use the arrow symbols to program the AUTO
START TIME by increasing or decreasing the hour
setting above the cursor. Touch the SEL symbol to
advance the cursor and program the minutes
setting. Select the SEL symbol to return to the
previous screen with the new time setting displayed.
Select the SEL symbol to exit the screen and return
to the Menu.

The Daylight Saving feature when enabled, will
automatically adjust the control clock for daylight
saving time. To Disable the Daylight Saving Time
feature, select the UP arrow to move the arrow to
Disable. Then touch the SEL symbol to save the
new setting.

The STANDBY option is used to manually place
either side of the machine in the Standby mode
during long, no draw periods. Select the STANDBY
screen from the Menu. Touch the SEL symbol to
activate Standby.

The AUTO START TIME option allows the Manager
to set the time of day at which the machine
automatically enters the AUTO mode from the
STANDBY mode. The machine must be in the
STANDBY mode in order to AUTO start at the
programmable time. The AUTO START TIME can
also be disabled and require starting the AUTO
mode manually. (See Figure 21.)

Discontinue Standby operation by exiting the
Manager's Menu and select the AUTO mode.
(See Figure 24.)

AUTO START TIME
DISABLED
Enable
Disable

STANDBY MODE

Figure 21

Model C713

EXIT

Figure 24

Important: To the Operator

The MIX LEVEL AUDIBLE option, when enabled,
will alert the operator with an audible tone when
there is mix low or mix out condition. The following
screen is displayed upon selecting this option.
(See Figure 25.)

Faults Occurring While in AUTO Mode
HPR>41F (5C) AFTER 4 HR - The mix temperature
in the hopper was above 41_F (5_C) more than four
hours.

MIX LEVEL AUDIBLE
>

BRL>41F (5C) AFTER 4 HR - The mix temperature
in the freezing cylinder was above 41_F (5_C) more
than four hours.

Enable
Disable

HPR>41F (5C) AFTER PF - The mix temperature in
the hopper was above 41_F (5_C) more than four
hours following a power failure.

Figure 25
Disable the audible tone feature by selecting the UP
arrow symbol to move the arrow to Disable. Select
the SEL symbol to save the new setting and return
to the Menu. The control panel icons for Mix Low
and Mix Out will light as the mix level drops in the
hopper but the audible tone will be disabled.

BRL>41F (5C) AFTER PF - The mix temperature in
the freezing cylinder was above 41_F (5_C) more
than four hours following a power failure.
HPR>45F (7C) AFTER 1 HR - The mix temperature
in the hopper was above 45_F (7_C) more than one
hour.

The LOCKOUT HISTORY screen displays a history
of the faults. (See Figure 26.)
LOCKOUT HISTORY
07/27/04
<
HPR THERM FAIL
>
EXIT

BRL>45F (7C) AFTER 1 HR - The mix temperature
in the freezing cylinder was above 45_F (7_C) more
than one hour.

12:58

HPR>59F (15C) - The mix temperature in the
hopper exceeded 59_F (15_C).
BRL>59F (15C) - The mix temperature in the
freezing cylinder exceeded 59_F (15_C).

Figure 26
Use the arrow symbols to advance forward or
backward to view each screen. The following list
indicates the variable messages that may appear.

Important: To the Operator

Note: Refer to your local health codes regarding
temperature recommendations for procedures to
follow if these fault screens appear.

Model C713

The SYSTEM INFORMATION is displayed on three
separate screens. The first screen contains the
control and software version installed in the
machine. (See Figure 27.)

Touch the SEL symbol to advance to the third
system information screen containing the model bill
of material and machine serial number. Touching the
SEL symbol again will return to the Menu list.
(See Figure 29.)

SOFTWARE VERSION
C713 CONTROL UVC3
VERSION 1.04
> Next

B.O.M. C71333C000
S/N
K0000000
> Next

Figure 27
Touch the SEL symbol to advance to the next
system information screen containing the software
language version. (See Figure 28.)

Figure 29

Language
V1.11 r 00 English 515
> Next

Figure 28

Model C713

Important: To the Operator

Section 6

Operating Procedures

The C713 machine stores mix in the hoppers. It has
two 3.4 quart (3.2 liter) capacity freezing cylinders
with a three spout door. Mix flows by gravity through
a feed tube down into the freezing cylinders.

Step 3
Heavily lubricate the inside portion of the boot seal
and also lubricate the flat end of the boot seal that
comes in contact with the rear shell bearing.

We begin our instructions at the point where we
enter the store in the morning and find the parts
disassembled and laid out to air dry from the
previous night's cleaning.

Step 4
Apply an even coat of lubricant to the shaft. DO
NOT lubricate the hex end.

These opening procedures will show you how to
assemble these parts into the freezer, sanitize them,
and prime the freezer with fresh mix in preparation
to serve your first portion.
If you are disassembling the machine for the first
time or need information to get to this starting point
in our instructions, turn to page 30, “Disassembly”,
and start there.

Figure 30

Freezing Cylinder Assembly

Note: To ensure the mix does not leak out of the
back of the freezing cylinder, the middle section of
the boot seal should be convex or extend out from
the seal. If the middle section of the boot seal is
concave or extending into the middle of the seal,
turn the seal inside out.

Note: When lubricating parts, use an approved food
grade lubricant (example: Taylor Lube).

MAKE SURE THE POWER SWITCH IS IN
THE “OFF” POSITION! Failure to follow this
instruction may result in severe personal injury from
hazardous moving parts.
Step 1
Before installing the beater drive shaft, lubricate the
groove on the beater drive shaft.
Step 2
Slide the beater drive shaft boot seal over the small
end of the beater drive shaft and engage into the
groove on the shaft.

Figure 31

110107

Operating Procedures

Model C713

Step 5
Insert the beater drive shaft through the rear shell
bearing in the freezing cylinder and engage the hex
end firmly into the drive coupling.

Step 7
Holding the beater securely, slide the beater into the
freezing cylinder about one-third of the way in.
Looking into the freezing cylinder, align the hole at
the rear of the beater with the flats on the end of the
drive shaft.

Figure 32

USE EXTREME CAUTION when handling
the beater assembly. The scraper blades are very
sharp and may cause injury.

Figure 34

Step 6
Before installing the beater assembly, check the
scraper blades. If they are in good condition, take
one of the scraper blades and slip it under the hook
at the front of the beater. Wrap the blade around the
beater, following the helix and pushing the blade
down onto the helix as you wrap. At the back end of
the beater, slip the blade under the hook.

Step 8
Slide the beater the remainder of the way into the
freezing cylinder and over the end of the drive shaft.
The beater should fit snugly but not so tightly that
the beater cannot be turned slightly to engage the
drive shaft.
Make sure the beater assembly is in position over
the drive shaft. Turn the beater slightly to be certain
that the beater is properly seated. When in position,
the beater will not protrude beyond the front of the
freezing cylinder.
Step 9
Repeat these steps for the other side of the
machine.
Step 10
To assemble the freezer door, place the door
gaskets into the grooves on the back of the freezer
door. Slide the front bearings over the baffle rods.
The flanged edges should be against the door. DO
NOT lubricate the gaskets or bearings.

Figure 33
Repeat this step for the second scraper blade.

Model C713

Operating Procedures

Step 11
Slide the two o-rings into the grooves on each prime
plug. Apply an even coat of Taylor Lube to the
o-rings and shafts.

Step 13
To install the freezer door, insert the baffle rods
through the beaters in the freezing cylinders.

Figure 37
Figure 35

With the door seated on the freezer studs, install the
handscrews. Use the long handscrews on the top
and the short handscrews on the bottom. Tighten
them equally in a criss-cross pattern to insure the
door is snug.

Step 12
Insert the prime plugs into the holes in the top of the
freezer door and push down.

Figure 36

Operating Procedures

Figure 38

Model C713

Step 14
Slide the three o-rings into the grooves of each
standard draw valve. Slide the H-ring and o-ring into
the grooves of the center draw valve. Lubricate the
H-ring and o-rings.

Step 16
Insert the draw valves from the bottom until the slot
in the draw valves come into view.

Figure 41
Step 17
Slide the fork of the draw handles in the slot of the
draw valves, starting from the right.

Figure 39
Step 15
Lubricate the inside of the freezer door spouts, top
and bottom.

Figure 42
Step 18
Slide the pivot pin through each draw handle as they
are inserted into the draw valves.

Figure 40

Figure 43

Model C713

Operating Procedures

Step 21
Install the front drip tray and splash shield under the
door spouts.

Note: This freezer features three adjustable draw
handles to provide portion control, giving a better
consistent quality to your product and controlling
costs. The draw handle should be adjusted to
provide a flow rate of 5 to 7-1/2 oz. (142 g. to
213 g.) of product by weight per 10 seconds.
To INCREASE the flow rate, turn the adjustment
screw CLOCKWISE. Turn the adjustment screw
COUNTER-CLOCKWISE to DECREASE the flow
rate.
Step 19
Snap the design caps over the bottom of the door
spouts.

Figure 46
Step 22
Slide two o-rings on one end of the feed tube. Slide
two o-rings on the other end of the feed tube.

Figure 44
Step 20
Slide the two drip pans into the holes in the side
panels.

Figure 47
Step 23
Slide the small o-ring into the groove of the air
orifice. Do not lubricate the o-ring.

Figure 45

Operating Procedures

Figure 48

Model C713

Note: Make sure the hole in the air orifice is clean
and is not clogged. If the hole in the air orifice should
become clogged, use soap and hot water to clear
the hole. Do not enlarge the hole in the air
orifice.
Step 24
Install the air orifice into the hole in the top of the
feed tube (end without the small hole on the side).

Figure 50
Note: You have just sanitized the mix hopper and
parts; therefore, be sure your hands are clean and
sanitized before going on in these instructions.
Step 3
While the solution is flowing into the freezing
cylinder, take particular care to brush-clean the mix
level sensing probe on the bottom of the hopper, the
mix hopper, the mix inlet hole, and the mix feed
tube.

Figure 49
Step 25
Lay the feed tube (with the air orifice installed) in the
bottom of the mix hopper for sanitizing.
Step 26
Repeat steps 22 through 25 for the other side of
the machine.

Sanitizing
Step 1
Prepare an approved 100 PPM sanitizing solution
(examples: 2-1/2 gal. [9.5 liters] of Kay-5R or 2
gal. [7.6 liters] of Stera-SheenR). USE WARM
WATER AND FOLLOW THE MANUFACTURER'S
SPECIFICATIONS.

Figure 51
Step 4
Prepare another pail of approved 100 PPM sanitizing solution (examples: 2-1/2 gal. [9.5 liters] of
Kay-5R or 2 gal. [7.6 liters] of Stera-SheenR).
USE WARM WATER AND FOLLOW THE MANUFACTURER'S SPECIFICATIONS.

Step 2
Pour the sanitizing solution over all the parts in the
bottom of the mix hopper and allow it to flow into the
freezing cylinder.

Model C713

Operating Procedures

Step 5
Pour the sanitizing solution into the mix hopper.

Priming

Step 6
Brush the exposed sides of the hopper.

Note: Use only FRESH MIX when priming the
freezer.

Step 7
Place the power switch in the ON position.

Step 1
Place an empty pail beneath the door spouts. With
the prime plug in the UP position, pour 2-1/2 gallons
(9.5 liters) of FRESH mix into the mix hopper and
allow it to flow into the freezing cylinder.

Step 8
Touch the WASH symbol . This will cause the
sanitizing solution in the freezing cylinder to be
agitated. Wait at least 5 minutes before proceeding
with these instructions.

Step 2
Open the draw valve to remove all sanitizing
solution. When only fresh mix is flowing, close the
draw valve.

Step 9
With an empty pail beneath the door spouts, raise
the prime plug.
Step 10
When a steady stream of sanitizing solution is
flowing from the prime plug opening in the bottom of
the freezer door, open the draw valve. Momentarily
open the center draw valve to sanitize the center
door spout. Draw off the remaining sanitizing
solution.

Step 3
Once a steady stream of mix starts to flow from the
prime plug opening in the bottom of the freezer door,
push the prime plug down.
Step 4
When mix stops bubbling down into the freezing
cylinder, install the end of the feed tube with the
hole in it into the mix inlet hole in the mix hopper.
Make sure the air orifice is installed in the feed tube.

Step 11
Once the sanitizer stops flowing from the door
spout, touch the WASH symbol
draw valve.

and close the

Step 5

Note: Be sure your hands are clean and
sanitized before going on in these instructions.

Select the AUTO symbol

Step 12
Lubricate the feed tube o-rings on the end with the
small hole on the side. Stand the feed tube in the
corner of the hopper.

Step 6
Fill the hopper with fresh mix and place the mix
hopper cover in position.

Step 13
Repeat these steps for the other side of the
machine.

Step 7
Repeat these steps for the other side of the
machine.

140721

Operating Procedures

Model C713

Manual Brush Cleaning

Rinsing

Step 1
Pour two gallons (7.6 liters) of cool, clean water into
the mix hopper. With the white hopper brush, scrub
the mix hopper and the mix level sensing probe.
Using the double ended brush, brush clean the mix
inlet hole.

ALWAYS FOLLOW LOCAL HEALTH CODES.

To disassemble the Model C713, the following items
will be needed:

S
S
S
S

Two cleaning and sanitizing pails
Sanitizer/Cleaner
Necessary brushes (provided with freezer)
Single service towels

Draining Product From The
Freezing Cylinder
Step 1
Remove the hopper cover and the feed tube. Take
them to the sink for cleaning.
Step 2
With a pail beneath the door spouts, touch the
WASH symbol

Figure 52

and open the draw valve.
Note: Do not brush clean the mix inlet hole while
the machine is in the WASH mode.

Step 3
If local health codes permit the use of rerun,
place a sanitized, NSF approved stainless steel
rerun container beneath the door spout. Press the
WASH key and open the draw valve. Drain the
remaining product from the freezing cylinder and mix
hopper. When the flow of product stops, press the
WASH key and close the draw valve. Place the
sanitized lid on the rerun container and place it in
the walk-in cooler.

Step 2
With a pail beneath the door spout, raise the prime
plug and touch the WASH symbol

Step 3
When a steady stream of rinse water is flowing from
the prime plug opening in the bottom of the freezer
door, open the draw valve. Drain all the rinse water
from the door spout. Close the draw valve, and

Note: If local health codes DO NOT permit the
use of rerun, the product must be discarded.
Follow the instructions in the previous step, except
drain the product into a pail and properly discard the
mix.

touch the WASH symbol,
mode.

cancelling the Wash

Step 4
Repeat this procedure using clean, warm water until
the water being discharged is clear.

ALWAYS FOLLOW LOCAL HEALTH CODES.

Repeat these steps for the other side of the
machine.

140721

Model C713

Operating Procedures

Hopper Cleaning

Disassembly
Step 1
Place the power switch in the OFF position.

Note: Failure to follow these steps will result in
milk-stone build-up.

Step 2
Remove the handscrews, freezer door, beater and
scraper blades, and drive shaft with drive shaft seal
from the freezing cylinder.

Step 1
Prepare an approved 100 PPM cleaning solution
(examples: 2-1/2 gal. [9.5 liters] of Kay-5R or 2
gal. [7.6 liters] of Stera-SheenR). USE WARM
WATER AND FOLLOW THE MANUFACTURER'S
SPECIFICATIONS.

Step 3
Remove the scraper blades from the beater
assembly.
Step 4
Remove the drive shaft seal from the drive shaft.

Step 2
Push the prime plug down. Pour the cleaning
solution into the hopper and allow it to flow into the
freezing cylinder.

Step 5
Remove the freezer door gasket, front bearing, pivot
pin, draw handle, draw valve, prime plugs and
design caps. Remove the three o-rings from the
draw valve.

Step 3
Using the white hopper brush, clean the mix hopper
and the mix level sensing probes. Using the double
ended brush, clean the mix inlet hole.

Repeat these steps on the other side of the
machine.

Note: Do not brush clean the mix inlet hole while
the machine is in the WASH mode.

Step 6
Remove the front drip tray and splash shield.

Step 4

Step 7
Remove all drip pans. Take them to the sink for
cleaning.

Touch the WASH symbol . This will cause the
cleaning solution in the freezing cylinder to come in
contact with all areas of the freezing cylinder.
Step 5
Place an empty pail beneath the door spouts and
raise the prime plug.
Step 6
When a steady stream of cleaning solution is flowing
from the prime plug opening in the bottom of the
freezer door, open the draw valve. Draw off all the
solution.
Step 7
Once the cleaning solution stops flowing from the
door spout, close the draw valve and touch the
WASH symbol

Figure 53

, cancelling the Wash mode.

Note: If the drip pans are filled with an excessive
amount of mix, it is an indication that the drive shaft
seal(s), or o-ring(s) should be replaced or properly
lubricated.

Repeat these steps on the other side of the
machine.

Operating Procedures

Model C713

Brush Cleaning
Step 1
Prepare an approved 100 PPM cleaning solution
(examples: 2-1/2 gal. [9.5 liters] of Kay-5R or 2
gal. [7.6 liters] of Stera-SheenR). USE WARM
WATER AND FOLLOW THE MANUFACTURER'S
SPECIFICATIONS. Make sure all brushes provided
with the freezer are available for brush cleaning.
Step 2
Thoroughly brush clean all disassembled parts in the
cleaning solution, making sure all lubricant and mix
film is removed. Be sure to brush all surfaces and
holes, especially the holes in the freezer door.
Figure 54

Step 3
Rinse all parts with clean, warm water. Place the
parts on a clean, dry surface to air dry overnight.

Repeat these steps on the other side of the
machine.

Step 4
Return to the freezer with a small amount of
cleaning solution. Using the black brush, clean the
rear shell bearing at the back of the freezing
cylinder.

Model C713

Step 5
Wipe all exterior surfaces of the freezer with a clean,
sanitized towel.

Operating Procedures

Section 7

Important: Operator Checklist
j 5. IF LOCAL HEALTH CODES PERMIT THE
USE OF RERUN, make sure the mix rerun is
stored in a sanitized, covered, NSF approved
stainless steel rerun container and used the
following day. DO NOT prime the machine
with rerun. When using rerun, skim off the
foam and discard; then mix the rerun with
fresh mix in a ratio of 50/50 during the day's
operation.

During Cleaning and Sanitizing

ALWAYS FOLLOW LOCAL HEALTH CODES.

Cleaning and sanitizing schedules are governed
by federal, state, or local regulatory agencies,
and must be followed accordingly. If the unit
has a “Standby mode”, it must not be used in
lieu of proper cleaning and sanitizing
procedures and frequencies set forth by the
ruling health authority. The following check
points should be stressed during the cleaning
and sanitizing operations.

j 6. On a designated day of the week, run the mix
as low as feasible and discard it after closing.
This will break the rerun cycle and reduce the
possibility of high bacteria and coliform
counts.
j 7. Properly prepare the cleaning and sanitizing
solutions. Read and follow the label directions
carefully. Too strong of a solution may
damage the parts and too weak of a solution
will not do an adequate job of cleaning or
sanitizing.

Troubleshooting Bacterial Count

j 8. The temperature of the mix in the mix hopper
and walk-in cooler should be below 40_F
(4.4_C).

j 1. Thoroughly clean and sanitize the machine
regularly, including complete disassembly and
brush cleaning.

Regular Maintenance Checks

j 2. Use all brushes supplied for thorough
cleaning. The brushes are specially designed
to reach all mix passageways.

j 1. Replace scraper blades that are nicked or
damaged. Before installing the beater
assembly, be certain that scraper blades are
properly attached to the helix.

j 3. Use the white bristle brush to clean the mix
inlet hole which extends from the mix hopper
down to the rear of the freezing cylinder.

j 2. Check the rear shell bearing for signs of wear
(excessive mix leakage in rear drip pan) and
be certain it is properly cleaned.

j 4. Use the black bristle brush to thoroughly
clean the rear shell bearing located at the rear
of the freezing cylinder. Be sure there is a
generous amount of cleaning solution on the
brush.

j 3. Using a screwdriver and cloth towel, keep the
rear shell bearing and the female hex drive
socket clean and free of lubricant and mix
deposits.

120210

Important: Operator Checklist

Model C713

j 4. Dispose of o-rings and seals if they are worn,
torn, or fit too loosely, and replace with new
ones.

Winter Storage
If the place of business is to be closed during the
winter months, it is important to protect the freezer
by following certain precautions, particularly if the
building is subject to freezing conditions.

j 5. Follow all lubricating procedures as outlined in
“Assembly”.
j 6. If your machine is air cooled, check the
condensers for accumulation of dirt and lint.
Dirty condensers will reduce the efficiency
and capacity of the machine. Condensers
should be cleaned monthly with a soft brush.
Never use screwdrivers or other metal probes
to clean between the fins.
Note: For machines equipped with an air
filter, it will be necessary to vacuum clean the
filters on a monthly schedule.

Disconnect the freezer from the main power source
to prevent possible electrical damage.
On water cooled freezers, disconnect the water
supply. Relieve pressure on the spring in the water
valve. Use air pressure on the outlet side to blow out
any water remaining in the condenser. This is
extremely important. Failure to follow this
procedure may cause severe and costly damage to
the refrigeration system.
Your local Taylor Distributor can perform this winter
storage service for you.

Caution: Always disconnect
electrical power prior to cleaning the
condenser. Failure to follow this instruction
may result in electrocution.

Wrap detachable parts of the freezer such as
beater, blades, drive shaft, and freezer door, and
place them in a protected dry place. Rubber trim
parts and gaskets can be protected by wrapping
them with moisture-proof paper. All parts should be
thoroughly cleaned of dried mix or lubrication which
attract mice and other vermin.

j 7. If your machine is water cooled, check the
water lines for kinks or leaks. Kinks can occur
when the machine is moved back and forth for
cleaning or maintenance purposes.
Deteriorated or cracked water lines should be
replaced only by an authorized Taylor
distributor.

Model C713

It is recommended that an authorized service
technician perform winter storage draining, to insure
all water has been removed. This will guard against
freezing and rupturing of the components.

Important: Operator Checklist

Section 8
PROBLEM

Troubleshooting Guide
REMEDY

PAGE
REF.

a. Low on mix. The MIX
OUT light is on.

a. Add mix to the mix
hopper. Return to AUTO
mode.

b. The power switch is in the
OFF position.

b. Place the power switch to
ON and select AUTO.

c. Machine not in AUTO
mode.

c. Select AUTO and allow
machine to cycle off
before drawing product.

d. Beater motor is out on
reset. The BEATER
OVERLOAD message
displayed.

d. Turn the machine off.
Press the reset button.
Restart the machine in
AUTO.

---

e. Freeze-up in mix inlet
hole.

e. Call an authorized service
technician.

---

f. Feed tube is not properly
installed.

f. Make sure feed tube is
properly installed.

2. The product is too soft.

a. Draw rate is set too fast.

a. Adjust draw rate of 5 to 7
1/2 oz. (142 g. to 213 g.)
of product by weight in 10
seconds.

3. The product is too thick.

a. Freezing cylinder not
primed correctly.

a. Drain the freezing cylinder
and reprime the machine.

b. The viscosity control is set
too cold.

b. Call an authorized service
technician.

---

c. Freeze-up in mix inlet
hole.

c. Call an authorized service
technician.

---

1. No product is being
dispensed.

Important: Operator Checklist

PROBABLE CAUSE

Model C713

PROBLEM

REMEDY

PAGE
REF.

a. Hopper cover is not in
position.

a. Clean and sanitize hopper
cover and place in
position.

b. The hopper temperature is
out of adjustment.

b. Call an authorized service
technician.

---

5. The mix in the hopper is
too cold.

a. The hopper temperature is
out of adjustment.

a. Call an authorized service
technician.

---

6. Mix Low and Mix Out
probes are not
functioning.

a. Milkstone build-up in the
hopper.

a. Clean hoppers thoroughly.

7. Product is collecting on
top of the freezer door.

a. The top o-ring on draw
valve is improperly
lubricated or worn.

a. Lubricate properly or
replace the o-ring.

8. Excessive mix leakage
from the bottom of door
spout.

a. Bottom o-ring on draw
valve is improperly
lubricated or worn.

a. Lubricate properly or
replace the o-ring.

9. Excessive mix leakage
into the long drip pan.

a. The seal on drive shaft is
improperly lubricated or
worn.

a. Lubricate properly or
replace the seal.

b. The seal is installed
inside-out on the drive
shaft.

b. Install correctly.

c. Inadequate lubrication of
the drive shaft.

c. Lubricate properly.

d. The drive shaft and beater
assembly work forward.

d. Call an authorized service
technician.

---

e. Worn rear shell bearing.

e. Call an authorized service
technician.

---

f. Gear box out of alignment.

f. Call an authorized service
technician.

---

a. Mix and lubricant collected
in drive coupling.

a. Brush clean the rear shell
bearing area regularly.

b. Rounded corners of drive
shaft, drive coupling, or
both.

b. Call an authorized service
technician.

---

c. Gear box is out of
alignment.

c. Call an authorized service
technician.

---

4. The mix in the hopper is
too warm.

10. The drive shaft is stuck in
the drive coupling.

Model C713

PROBABLE CAUSE

Important: Operator Checklist

PROBLEM
11. The freezing cylinder
walls are scored.

12. The product makes a
popping sound when
drawn.

13. No control panel functions
with power switch ON.

Important: Operator Checklist

PROBABLE CAUSE

REMEDY

PAGE
REF.

a. Missing or worn front
bearing.

a. Install or replace the front
bearing.

b. Broken freezer door baffle
rod.

b. Replace freezer door.

c. Beater assembly is bent.

c. Replace beater assembly.

d. Gear box is out of
alignment.

d. Call an authorized service
technician.

---

a. Draw rate is set too fast.

a. Adjust draw rate of 5 to 7
1/2 oz. (142 g. to 213 g.)
of product by weight in 10
seconds.

b. Freezing cylinder not
primed correctly.

b. Drain the freezing cylinder
and reprime the machine.

a. Machine is unplugged.

a. Plug into wall receptacle.

---

b. Circuit breaker OFF or
blown fuse.

b. Turn the breaker ON or
replace the fuse.

---

Model C713

Section 9
PART DESCRIPTION

Parts Replacement Schedule
EVERY 3 MONTHS

EVERY 6 MONTHS

ANNUALLY

White Bristle Brush, 3” x 7”

Inspect & Replace
if Necessary

Minimum

White Bristle Brush, 1” x 2”

Inspect & Replace
if Necessary

Minimum

Black Bristle Brush, 1” x 2”

Inspect & Replace
if Necessary

Minimum

Double-Ended Brush

Inspect & Replace
if Necessary

Minimum

Scraper Blade

Drive Shaft Seal

Freezer Door Gasket

Front Bearing

Draw Valve O-Ring

Draw Valve Seal

Prime Plug O-Ring

Mix Feed Tube O-Ring

Design Cap

Model C713

Parts Replacement Schedule

Section 10 Limited Warranty on Equipment
TAYLOR COMPANY LIMITED WARRANTY ON FREEZERS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor-branded freezer equipment available from Taylor to the market generally (the “Product”)
to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Product against failure due to defect in materials or workmanship under normal use and
service as follows. All warranty periods begin on the date of original Product installation. If a part fails due to
defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service agency,
will provide a new or re-manufactured part, at Taylor’s option, to replace the failed defective part at no charge for
the part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited warranty
for a Product failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions listed
below and on the reverse (if any) of this document.
Product
Soft Serve
Frozen Yogurt
Shakes
Smoothies
Frozen Beverage
Batch Desserts

Part

Limited Warranty Period

Insulated shell assembly

Five (5) years

Refrigeration compressor
(except service valve)

Five (5) years

Beater motors

Two (2) years

Beater drive gear

Two (2) years

Printed circuit boards and
Softech controls beginning
with serial number H8024200

Two (2) years

Parts not otherwise listed in
this table or excluded below

One (1) year

LIMITED WARRANTY CONDITIONS
1.

If the date of original installation of the Product cannot be verified, then the limited warranty period begins
ninety (90) days from the date of Product manufacture (as indicated by the Product serial number). Proof of
purchase may be required at time of service.

This limited warranty is valid only if the Product is installed and all required service work on the Product is
performed by an authorized Taylor distributor or service agency, and only if genuine, new Taylor parts are
used.

Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.

Defective parts must be returned to the authorized Taylor distributor or service agency for credit.

The use of any refrigerant other than that specified on the Product’s data label will void this limited warranty.
LIMITED WARRANTY EXCEPTIONS

This limited warranty does not cover:
1.

Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective parts, replacement parts, or new Products.

Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers.

131121

Limited Warranty on Equipment

Model C713

Replacement of wear items designated as Class “000” parts in the Taylor Operator’s Manual.

External hoses, electrical power supplies, and machine grounding.

Parts not supplied or designated by Taylor, or damages resulting from their use.

Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.

Failure, damage or repairs due to faulty installation, misapplication, abuse, no or improper servicing,
unauthorized alteration or improper operation or use as indicated in the Taylor Operator’s Manual, including
but not limited to the failure to use proper assembly and cleaning techniques, tools, or approved cleaning
supplies.

Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the electrical or
water supply specification of the Product; or components repaired or altered in any way so as, in the
judgment of the Manufacturer, to adversely affect performance, or normal wear or deterioration.

Any Product purchased over the Internet.

10.

Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.

11.

Electricity or fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

12.

Damages resulting from the use of any refrigerant other than that specified on the Product’s data label will
void this limited warranty.

13.

Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

14.

ANY SPECIAL, INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL DAMAGE OF ANY
NATURE WHATSOEVER. Some jurisdictions do not allow the exclusion of incidental or consequential
damages, so this limitation may not apply to you.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.
LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
COMPONENTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL
OR INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Product, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Product under warranty, mailed at least thirty (30) days before pursuing any legal rights or
remedies.

Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.

Model C713

Limited Warranty on Equipment

Section 11

Limited Warranty on Parts

TAYLOR COMPANY LIMITED WARRANTY ON TAYLOR GENUINE PARTS
Taylor Company, a division of Carrier Commercial Refrigeration, Inc. (“Taylor”) is pleased to provide this limited
warranty on new Taylor genuine replacement components and parts available from Taylor to the market generally
(the “Parts”) to the original purchaser only.
LIMITED WARRANTY
Taylor warrants the Parts against failure due to defect in materials or workmanship under normal use and service
as follows. All warranty periods begin on the date of original installation of the Part in the Taylor unit. If a Part fails
due to defect during the applicable warranty period, Taylor, through an authorized Taylor distributor or service
agency, will provide a new or re-manufactured Part, at Taylor’s option, to replace the failed defective Part at no
charge for the Part. Except as otherwise stated herein, these are Taylor’s exclusive obligations under this limited
warranty for a Part failure. This limited warranty is subject to all provisions, conditions, limitations and exclusions
listed below and on the reverse (if any) of this document.
Limited Warranty Period

Part's Warranty Class Code or Part
Class 103 Parts¹

Three (3) months

Class 212 Parts²

Twelve (12) months

Class 512 Parts

Twelve (12) months

Class 000 Parts

No warranty

Taylor Part #072454 (Motor-24VDC *C832/C842*)

Four (4) years

LIMITED WARRANTY CONDITIONS
1.

If the date of original installation of the Part cannot be otherwise verified, proof of purchase may be required
at time of service.

This limited warranty is valid only if the Part is installed and all required service work in connection with the
Part is performed by an authorized Taylor distributor or service agency.

The limited warranty applies only to Parts remaining in use by their original owner at their original installation
location in the unit of original installation.

Installation, use, care, and maintenance must be normal and in accordance with all instructions contained in
the Taylor Operator’s Manual.

Defective Parts must be returned to the authorized Taylor distributor or service agency for credit.

This warranty is not intended to shorten the length of any warranty coverage provided pursuant to a separate
Taylor Limited Warranty on freezer or grill equipment.

The use of any refrigerant other than that specified for the unit in which the Part is installed will void this
limited warranty.

1, 2

Except that Taylor Part #032129SER2 (Compressor-Air-230V SERV) and Taylor Part #075506SER1
(Compressor-Air-115V 60HZ) shall have a limited warranty period of twelve (12) months when used in Taylor
freezer equipment and a limited warranty period of two (2) years when used in Taylor grill equipment.
131121

Limited Warranty on Parts

Model C713

LIMITED WARRANTY EXCEPTIONS
This limited warranty does not cover:
1.

Labor or other costs incurred for diagnosing, repairing, removing, installing, shipping, servicing or handling of
defective Parts, replacement Parts, or new Parts.

Normal maintenance, cleaning and lubrication as outlined in the Taylor Operator’s Manual, including cleaning
of condensers or carbon and grease buildup.

Required service, whether cleaning or general repairs, to return the cooking surface assemblies, including
the upper platen and lower plate, to an operational condition to achieve proper cooking or allow proper
assembly of release sheets and clips as a result of grease build-up on the cooking surfaces, including but
not limited to the platen and plate, sides of the shroud or top of the shroud.

Replacement of cooking surfaces, including the upper platen and lower plate, due to pitting or corrosion (or
in the case of the upper platen, due to loss of plating) as a result of damage due to the impact of spatulas or
other small wares used during the cooking process or as a result of the use of cleaners, cleaning materials
or cleaning processes not approved for use by Taylor.

Replacement of wear items designated as Class “000” Parts in the Taylor Operator’s Manual, as well as any
release sheets and clips for the Product’s upper platen assembly.

External hoses, electrical power supplies, and machine grounding.

Parts not supplied or designated by Taylor, or damages resulting from their use.

Return trips or waiting time required because a service technician is prevented from beginning warranty
service work promptly upon arrival.

10.

Failure, damage or repairs due to theft, vandalism, wind, rain, flood, high water, water, lightning, earthquake
or any other natural disaster, fire, corrosive environments, insect or rodent infestation, or other casualty,
accident or condition beyond the reasonable control of Taylor; operation above or below the gas, electrical or
water supply specification of the unit in which a part is installed; or Parts or the units in which they are
installed repaired or altered in any way so as, in the judgment of Taylor, to adversely affect performance, or
normal wear or deterioration.

11.

Any Part purchased over the Internet.

12.

Failure to start due to voltage conditions, blown fuses, open circuit breakers, or damages due to the
inadequacy or interruption of electrical service.

13.

Electricity, gas or other fuel costs, or increases in electricity or fuel costs from any reason whatsoever.

14.

Damages resulting from the use of any refrigerant other than that specified for the unit in which the Part is
installed will void this limited warranty.

15.

Any cost to replace, refill or dispose of refrigerant, including the cost of refrigerant.

16.

This limited warranty gives you specific legal rights, and you may also have other rights which vary from
jurisdiction to jurisdiction.

Model C713

Limited Warranty on Parts

LIMITATION OF WARRANTY
THIS LIMITED WARRANTY IS EXCLUSIVE AND IS IN LIEU OF ALL OTHER WARRANTIES, CONDITIONS
AND/OR REMEDIES UNDER THE LAW, INCLUDING ANY IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE ORIGINAL OWNER'S SOLE
REMEDY WITH RESPECT TO ANY PRODUCTS SHALL BE REPAIR OR REPLACEMENT OF DEFECTIVE
PARTS UNDER THE TERMS OF THIS LIMITED WARRANTY. ALL RIGHTS TO CONSEQUENTIAL OR
INCIDENTAL DAMAGES (INCLUDING CLAIMS FOR LOST SALES, LOST PROFITS, PRODUCT LOSS,
PROPERTY DAMAGES OR SERVICE EXPENSES) ARE EXPRESSLY EXCLUDED. THE EXPRESS
WARRANTIES MADE IN THIS LIMITED WARRANTY MAY NOT BE ALTERED, ENLARGED, OR CHANGED
BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON, WHATSOEVER.
LEGAL REMEDIES
The owner must notify Taylor in writing, by certified or registered letter to the following address, of any defect or
complaint with the Part, stating the defect or complaint and a specific request for repair, replacement, or other
correction of the Part under warranty, mailed at least thirty (30) days before pursuing any legal rights or remedies.

Taylor Company
a division of Carrier Commercial Refrigeration, Inc.
750 N. Blackhawk Blvd.
Rockton, IL 61072, U.S.A.

Limited Warranty on Parts

Model C713

START RELAY
(047702-27)

LINE
13
14

WHITE
LINE

RUN
CAP.

RELAY

INTERNAL OVERLOAD
WHITE(120 VOLTS)
BLACK(230 VOLTS)

COMPRESSOR
TERMINAL
COVER

C S

START CAPACITOR
(047703)
11

RELAY

EQUIPMENT
GROUND

START CAP.

START CAPACITOR

FIG. 2

BROWN
S
BROWN
BLACK R
RUN CAPACITOR
BLEED RESISTOR
052396-1

BLUE
ABOVE ELECTRICAL DIAGRAM SHOWS WIRING NECESSARY
TO HOOK UP A COMPRESSOR USING A STAR T AND RUN
CAPACITOR (CSR) WITH A RELAY.

A.O. SMITH BEATER MOTOR WIRING
STEPS:
1) REMOVE BROWN JUMPER FROM BETWEEN TERMINAL #1 TO TERMINAL #5
2) MOVE BLUE INTERNAL (FROM MOTOR MAIN WINDING)
FROM TERMINAL #5 TO TERMINAL #1.
NOTE: FOR CCWLE - BLUE INTERNAL ON #1, YELLOW INTERNAL ON #6
BLUE INTERNAL
BEATER MOTOR
CONTACTOR
1
ORANGE INTERNAL
BLACK
T1
L1
2
BLUE
3
4
RED INTERNAL
BLUE
CP
CP

BLACK

T3
L3
USE T3 AND L3 WHEN
CP CONTACTS ARE NOT AVAILABLE
BLACK
T2
L2

SCHEMATIC WIRING DIAGRAM - CSR

YELLOW INTERNAL

START WINDING

MAIN WINDING

BLACK INTERNAL

WINDING PROTECTOR
(INTERNAL)

FIG. 1

COMPRESSOR WIRING
(MODEL TL3G W/HST)

LEESON BEATER MOTOR WIRING
STEPS:
1) DISCONNECT WIRE T7 FROM TERMINAL 3
2) SPLICE BLUE WIRE AS SHOWN

EXTERNAL
GROUND
L1 L2
TERMINAL BLOCK

BLK/BLU

BLK (GRD)

(+5
CLR
GRN

)

(GRD

GRN/YEL

J13

BLK

OPTIONAL COVER MOUNTED HOPPER AGITATOR

GRN
WHT
RED
BLK

1 23

L3
T3
USE T3 AND L3 WHEN
CP CONTACTS ARE NOT AVAILABLE
BLACK T2
L2

GRD

USE T3 AND L3 WHEN CP
CONTACTS ARE NOT AVAILABLE
BLACK
T2
L2

T4 OR YELLOW INTERNAL

208

1 234

BLK
WHT
BLK

OPTIONAL

BLK

WHT
BLK

BRN

BLK

BLK/WHT

WHT/ORN

BEATER
INTERLOCK
RELAY

WHT/ORN

1
9

BLK
BEATER
MOTOR
OVERLOAD
SWITCH

BRN

RED

C0M

BRN

WHT

O.T.
WHT

WHT

14
SYRUP HEATER

BLACK

WHT

BARREL LIQUID
SOLENOID

FIG .4

BEATER
MOTOR
INTERLOCK
N.O. SWITCH

BLK
BLK

THERMOSTA
190 F OPEN
140 F CLOSE

5
4

12
13

BEATER
MOTOR
STARTER
COIL

BLK

WHT

96 95

WHT/ORN

WHITE

GRY/WHT

WHT

BLK

SEE FIG. 3
SOFT SERVE

GRN/YEL
BEATER MOTOR
CABLE

M BLK T2

COMPRESSOR
SEE FIG. 2 CONTACTOR

AIR COOLED
CONDENSER
BLOWER MOTOR
BLK
WHT
M

BLK
BRN

BEATER MOTOR
STARTER

WHT

BLK

BLK
WATER COOLED
CONDENSER
FAN
BLK
BLK
M

MIX REF. SYSTEM
(DANFOSS TL3G COMPR.)
SEE FIG. 1

WHT

BLK

BEATER MOTOR
SOFT SERVE
STARTER
COMPRESSOR
BLK
T2
L2
M

BLK

C
L

BLK

RED
COMPRESSOR
CONTACTOR
COIL

BLK

BLU

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH

BLU

BLK

BLU

BLK

ORN

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

PANEL
JACK

LEFT SYRUP HEATER
SEE FIG. 4

BLK

BLU

BLK

J18

WHT

BLK
FUSE
15A

1 23456 7

BLK

OFF

FIG. 3

BLU

BLK

J5 J19

5 3 1 1 234567

BLUE

BLU/WHT

BLK

2
1 WHT
L1

(OPTIONAL)
BARRELHOPPER
--THERMISTOR PROBES--

BLK/WHT

BLU/WHT

BA
J14

J13
J1
B

J11
J12

CABLE

BLK
BLK

SV CABLE
WHT/RED

BLK

2
1 WHT/RED

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A.

BLK

OFF

ON BLK/WHT

GRN
CLR
CABLE

SELF-SERVICE
ENABLE
DISABLE ENABLE

8 7 6 5 4 3 21J10 10 9 8 7 6 5 4 3 21

BLK

MIX
LOW
PROBE

YEL

SV CABLE

PRP

MIX
OUT
PROBE

DRAW
SWITCH

YEL
BLK

NC
HOPPER
GROUND

RED/BLK
PRP

BLU
24 VAC

GND
+5V
J20

NO
YEL

COM

GRN/YEL

J9 OR BLACK INTERNAL

WHT

COM
BLU/WHT

RED
BLU

GRN/YEL

BLU/WHT

OUT

2 4 6 8 10
1 3 5 7 9

CABLE

BLUE

SV CABLE

ORN/WHT

BLUE
4

GRN/YEL
SV CABLE

DRAW
SWITCH

2 4 6 8 10
1 3 5 7 9

+5V

RIBBON CABLE
RED
BLU

RED
BLU

OPTIONAL REAR
MIX LEVEL LIGHTS

RIBBON
CABLE

J11
RIBBON CABLE

OFF

BLK

J10

GRN/YEL

RED

T1 OR BLUE INTERNAL
T8 OR RED INTERNAL
BLK/BLU

CLR

BLACK
5

WHT

RED
BLU

BEATER MOTOR
CONTACTOR

J12 OR PURPLE INTERNAL

COM

208

WHT

BLU
RED

J17

BLK

GE/RBC/MARATHON BEATER MOTOR WIRING
NOTE: FOR CCWLE - BLUE INTERNAL ON #1,YELLOW INTERNAL ON #2

24VAC

J15

BLK

RED

RIBBON CABLE

RED

WHT

CABLE

J16

BLK/BLU

BLU

WHT

UNIVERSAL CONTROL PCB A.

BLK
POWER
SWITCH
DPDT

BLUE

WHT

J12

BLUE
2

RIBBON CABLE

SV CABLE

ORN

BLK

240V

NOT
CONNECTED

INTERFACE BOARD
POWER TRANSFORMER
16V

BLACK

GRN/YEL

WHT

L1 LINE L2
EMI FILTER
L1 LOAD L2

4 56

BLK

GRN/YEL

BLK/BLU

- 8 LEDS
USER
- LCD SCREEN
J1
INTERFACE
- 9 KEYS
J2
BOARD
J3
- BEEPER

RED (+5v)

SV CABLE

BEATER MOTOR
CONTACTOR

BLK

BRN
WHT
M
FAN

BRN

BRN
START RELAY

10 14
11 13

COMP

LEFT SIDE
CONTROL

START CAP

BLU

RIGHT SIDE
CONTROL
L1 L2
TERMINAL BLOCK

BLU/WHT

BLK

SV CABLE

RED
BLU

RIBBON
CABLE

RED
BLU

GRN/YEL

BLK
BLK

J5 J19

CABLE

1 234

BLK

CLR

J6
1 23456 7

BLK

J18

BLK
BLK

5 3 1 1 234567

0
1
WHT
BLK

WHT
FUSE
15A

BLK

BLU/WHT

WHT/ORN

RIGHT SYRUP HEATER
SEE FIG. 4

1
9

BLK

WHT

WHT
BLK
BLK

BLK
WHT

BARREL LIQUID
SOLENOID

GRY/WHT

WHT

SEE FIG. 2

SOFT SERVE
GRN/YEL
BEATER MOTOR
M BLKT2

BEATER MOTOR
STARTER

BLK

BEATER MOTOR
SOFT SERVE
STARTER
COMPRESSOR
BLK
L2
T2
M

BLK

SEE FIG. 3

BLK
BLK

COMPRESSOR
CONTACTOR

PINS 3 AND 4

PINS 1 AND 2
DOMESTIC CONFIGURATION - JUMPER
INSTALLED. HOPPER TEMPERATURE NOT
DISPLAYED ON SCREEN/HEAT SYMBOL KEYS
ONLY ACTIVE WHEN A LOCKOUT CONDITION
HAS OCCURRED/STANDBY KEYS DISABLED.

INTERNATIONAL CONFIGURATION - NO JUMPER
INSTALLED. HOPPER TEMPERATURES
DISPLAYED ON SCREEN/MANUAL HEAT CYCLE
START BY SELECTING HEAT SYMBOL/STANDBY
KEYS FUNCTIONAL.

FUNCTION

RESERVED (DO NOT USE)

UVC4 BOARD

RESERVED (DO NOT USE)

JUMPER INSTALLED - BARREL AND HOPPER
TEMPERATURES ARE CHECKED DURING
AUTO/STANDBY. UNIT IS LOCKED OUT IF
EITHER BARREL OR HOPPER IS TOO WARM FOR
A PERIOD OF TIME. LOCKOUT OCCURS WHEN
BARREL OR HOPPER IS ABOVE 45F(7C) FOR
MORE THAN ONE HOUR OR ABOVE 41F(5C) FOR
MORE THAN FOUR HOURS.

RESERVED (DO NOT USE)

PINS 1 AND 2

JP3

JP1

JP4

NO JUMPER INSTALLED - NO LOCKOUT DURING
AUTO/STANDBY IF BARREL OR HOPPER IS TOO
WARM FOR A PERIOD OF TIME.

JP5

RESERVED (DO NOT USE)

FUNCTION

RESERVED (DO NOT USE)

JUMPER INSTALLED - FORCE BRUSH CLEAN
STATUS.
JUMPER INSTALLED - ACTIVATES SYRUP
HEATERS

RESERVED (DO NOT USE)

JP6

RESERVED (DO NOT USE)

JUMPER INSTALLED DISABLES RESET.

JP2

JP7

LEFT
INTERFACE
BOARD

RTCK

DBGEN

RESERVED (DO NOT USE)

PINS 7 & 8

FUNCTION

J10

RESERVED (DO NOT USE)

JUMPER INSTALLED - REDUCED MIX LOW
SENSITIVITY.
JUMPER INSTALLED - REDUCED MIX OUT
SENSITIVITY.
JUMPER INSTALLED W/SWITCH - SELF SERVE
APPLICATION ONLY. LOCKS OUT TOUCH
PANEL. NEW SWITCH ACTS AS THE ON/OFF
ABILITY TO ACTIVATE THE TOUCH PANEL.

JUMPER INSTALLED - ENABLES 59F HOPPER
TEMPERATURE CHECK.

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

RESERVED (DO NOT USE)

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

RESERVED (DO NOT USE)

RIGHT
INTERFACE
BOARD

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

JUMPER INSTALLED - REDUCED MIX LOW
SENSITIVITY.
JUMPER INSTALLED - REDUCED MIX OUT
SENSITIVITY.

2. RED WIRE ON RIBBON CABLES MUST BE
CONNECTED TO PIN 1 AT EACH END.

WHT

NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY
TOUCHING GROUNDED UNIT BEFORE
HANDLING SOLID STATE COMPONENTS.

RED

BEATER
MOTOR
STARTER
COIL

5
4

BLK

BEATER
MOTOR
OVERLOAD
SWITCH

BLK

RED
COMPRESSOR
CONTACTOR
COIL
WHT

BLK

C
L

96 95

WHT/ORN

ORN

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH

C0M

DRAW
SWITCH

BEATER
INTERLOCK
RELAY

WHT/ORN

BLK

* IF THE UNIT HAS THE INTEGRAL SYRUP OPTION-405, THEN THIS
JUMPER SHOULD BE INSTALLED.

GROUND FRAME SECURELY

WHT
BLK

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

PANEL
JACK

WHT

OPTIONAL

BLK

BLU/WHT

BLK

J14

J13
J1
A

BLK

2
1 RED/BLK

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A.
L2

BARREL HOPPER
--THERMISTOR PROBES--

J20

J11
J12

8 7 6 5 4 3 21J10 109 8 7 6 5 4 3 21

GND
+5V

YEL

MIX
LOW
PROBE

BLK

YEL
BLK

MIX
OUT
PROBE

DRAW
SWITCH

PRP/WHT

GRA/BLK
PRP/WHT

BLK

RED
BLU

RED/BLK
COM

BLU

GEN/YEL

BLU/WHT

JUMPER
INSTALLED
INITIALLY

YES

JUMPER
INSTALLED
INITIALLY

NO*

YES

JUMPER
INSTALLED
INITIALLY

YES

C713
059899-27
12/9/13

THERMOSTA
190 F OPEN
140 F CLOSE

EXTERNAL
GROUND
L1 L2

WHT

RED (+5v)
BLK (GRD)

(+5v)
CLR
)
(GRD
GRN

GRN/YEL
WHT

WHT
RIBBON CABLE

RIBBON CABLE

J13

OPTIONAL COVER MOUNTED HOPPER AGITATOR

GRN
WHT
RED
BLK

1 23

4 56

SV CABLE

24VAC

J15

GRD

START RELAY
(047702-27)
BLU

START CAPACITOR
(047703)

BLU

BLK

J19

1 234

BLUE

WHT/RED

L1
10

BLK

J18
2
1

WHT

BLK

1 23456 7

FUSE
15A

BLK
BLK

WHT

OPTIONAL
WHT

BLK

BRN

BLK/WHT

LEFT SYRUP HEATER
SEE FIG. 2
WHT/ORN

WHT/ORN

START WINDING

MAIN WINDING

BEATER
INTERLOCK
RELAY

WINDING PROTECTOR
(INTERNAL)

RED
COMPRESSOR
CONTACTOR
COIL

BRN

WHT

BEATER
MOTOR
OVERLOAD
SWITCH

C0M

BEATER
MOTOR
INTERLOCK
N.O. SWITCH

WHT

BARREL LIQUID
SOLENOID

8
14

BLACK

BLK
BLK

4
12
13

BLU

WHT/ORN

BEATER
MOTOR
STARTER
COIL

BLK

SOFT SERVE
GRN/YEL
BEATER MOTOR

M BLK T2

BEATER MOTOR
SOFT SERVE
STARTER
COMPRESSOR
BLK
L2
T2
M
T3

AIR COOLED
CONDENSER
BLOWER MOTOR
BLK
WHT
M

COMPRESSOR
CONTACTOR

BLK

CABLE

BLK
BLK

BEATER MOTOR
STARTER

BLK
WHT

BLK

WHT

BLK

GRY/WHT

BRN

WHT

BRN

BLK

WHT

BLK

WATER COOLED
CONDENSER FAN

BLK

96 95

WHITE

C
L

PANEL
JACK

COMPRESSOR WIRING
(MODEL TL3G W/HST)

BLU

BLK

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH
BLK

BLK

BLK
ORN

BLK

BLU/WHT

BLK

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A.

5 3 1 1 234567

BLK

RED

BLU/WHT

BA
J14

J13
J1
A

J11
J12

8 7 6 5 4 3 21J10 10 9 8 7 6 5 4 3 21

CABLE

BLK
BLK

YEL

BLK

YEL
BLK

PRP

SV CABLE

2
1

BLK

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

GRN/YEL

BLU

GRN
CLR
CABLE

BLK
BLK

BLK/WHT

BLU/WHT

GND
+5V
J20

BARRELHOPPER (OPTIONAL)
--THERMISTOR PROBES--

OFF

DRAW
SWITCH

SELF-SERVICE
ENABLE

BLU
24 VAC

DISABLE ENABLE

ON BLK/WHT

MIX
LOW
PROBE

1
SV CABLE

OFF

MIX
OUT
PROBE

WHT/RED

2 4 6 8 10
1 3 5 7 9

ORN/WHT
RED/BLK
PRP

YEL

DRAW
SWITCH

OFF

BLK

FIGURE 1
208

BLU/WHT

RED

COM

NO
NC

POWER
SWITCH
3PDT

WHT
COM

SV CABLE

ORN/WHT

RED

OUT

GRN/YEL
SV CABLE

GRN/YEL

CABLE

RIBBON CABLE
RED
BLU

2 4 6 8 10
1 3 5 7 9

+5V

RIBBON CABLE
RED
BLU

RED
BLU

OPTIONAL REAR
MIX LEVEL LIGHTS

RIBBON
CABLE

J11

BLK/BLU

J1
J10

GRN/YEL

HOPPER
GROUND

BLK

WHT

BLU
RED

J17

BLK
CLR

WHT

COM

208

UNIVERSAL CONTROL PCB A.

BLK

RED

WHT

BLK

ORN
RED

J16

BLK/BLU

BLU

WHT

J12

FIG .2

CABLE

240V
NOT
CONNECTED

16V

WHT

GRN/YEL

L1 LINE L2
EMI FILTER
L1 LOAD L2

INTERFACE BOARD
POWER TRANSFORMER

O.T.
WHT

WHT

SYRUP HEATER

BLK
BLK

BLK

BLK/BLU

SV CABLE

- 8 LEDS
USER
- LCD SCREEN
J1
INTERFACE
- 9 KEYS
J2
BOARD
J3
- BEEPER

BLK

GRN/YEL

TERMINAL BLOCK

BRN
WHT
M
FAN
BRN
10 14
11 13 COMP
START RELAY

BRN

LEFT SIDE
CONTROL

START CAP
MIX REF. SYSTEM
(DANFOSS TL3G COMPR.)
(ALSO SEE FIG.2)

BLU

RIGHT SIDE
CONTROL
L1 L2 L3

BLU/WHT

BLK

TERMINAL BLOCK

SV CABLE

RED
BLU

RIBBON
CABLE

RED
BLU

GRN/YEL

BLK

CABLE
BLK

BLK

CLR

BLK

J18

5 3 1 1 234567

1 23456 7

WHT

BLK
FUSE
15A

BLK
WHT

BLK

BLU/WHT

BLK

RIGHT SYRUP HEATER
SEE FIG. 2

WHT/ORN

BEATER
INTERLOCK
RELAY

WHT/ORN

1
9

BLK

WHT

BLK

WHT

C0M

BLK

BEATER
MOTOR
STARTER
COIL

BEATER
MOTOR
OVERLOAD
SWITCH

5
4

12
13

BLK

WHT/ORN

BLK

RED
COMPRESSOR
CONTACTOR
COIL
WHT

BLK

C
L

96 95

BLK

WHT
BLK
BLK

BLK
WHT

BARREL LIQUID
SOLENOID
GRY/WHT

BEATER MOTOR
SOFT SERVE
STARTER
COMPRESSOR
BLK
T2
L2
M
T3

BLK

SOFT SERVE
GRN/YEL
BEATER MOTOR
M BLK T2

BLK
BLK

BEATER MOTOR
STARTER

BLK

COMPRESSOR
CONTACTOR

PINS 1 AND 2
DOMESTIC CONFIGURATION - JUMPER
INSTALLED. HOPPER TEMPERATURE NOT
DISPLAYED ON SCREEN/HEAT SYMBOL KEYS
ONLY ACTIVE WHEN A LOCKOUT CONDITION
HAS OCCURRED/STANDBY KEYS DISABLED.

INTERNATIONAL CONFIGURATION - NO JUMPER
INSTALLED. HOPPER TEMPERATURES
DISPLAYED ON SCREEN/MANUAL HEAT CYCLE
START BY SELECTING HEAT SYMBOL/STANDBY
KEYS FUNCTIONAL.

FUNCTION

RESERVED (DO NOT USE)

UVC4 BOARD

RESERVED (DO NOT USE)

PINS 1 AND 2

JP3

RESERVED (DO NOT USE)

JP1

JP4

JUMPER INSTALLED DISABLES RESET.

NO JUMPER INSTALLED - NO LOCKOUT DURING
AUTO/STANDBY IF BARREL OR HOPPER IS TOO
WARM FOR A PERIOD OF TIME.

JP5

RESERVED (DO NOT USE)

FUNCTION

RESERVED (DO NOT USE)

JUMPER INSTALLED - FORCE BRUSH CLEAN
STATUS.
JUMPER INSTALLED - ACTIVATES SYRUP
HEATERS

RESERVED (DO NOT USE)

JP6

RESERVED (DO NOT USE)

PINS 3 AND 4

JP7

JP2

RTCK

LEFT
INTERFACE
BOARD

DBGEN

RESERVED (DO NOT USE)

FUNCTION

PINS 7 & 8

RESERVED (DO NOT USE)

J10

JUMPER INSTALLED - ENABLES 59F HOPPER
TEMPERATURE CHECK.

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

RESERVED (DO NOT USE)

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

RESERVED (DO NOT USE)

RIGHT
INTERFACE
BOARD

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

JUMPER INSTALLED - REDUCED MIX LOW
SENSITIVITY.
JUMPER INSTALLED - REDUCED MIX OUT
SENSITIVITY.

2. RED WIRE ON RIBBON CABLES MUST BE
CONNECTED TO PIN 1 AT EACH END.

BLK

NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY
TOUCHING GROUNDED UNIT BEFORE
HANDLING SOLID STATE COMPONENTS.

BLK

WHT

BLK

* IF THE UNIT HAS THE INTEGRAL SYRUP OPTION-405, THEN THIS
JUMPER SHOULD BE INSTALLED.

GROUND FRAME SECURELY

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH

BLK

ORN

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

RED

WHT

OPTIONAL

BLK

PANEL
JACK

BLK

J5 J19

1 234

J14

J13
J1
A

BLK

RED/BLK
BLK
BLK

BARREL HOPPER
--THERMISTOR PROBES--

DRAW
SWITCH

2
1

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A. 0
1
J8

BLU/WHT

GND
+5V
J20

YEL

BLK

MIX
LOW
PROBE

YEL
BLK

MIX
OUT
PROBE

PRP/WHT

GRA/BLK
PRP/WHT

BLK

DRAW
SWITCH

J11
J12

8 7 6 5 4 3 21J10 10 9 8 7 6 5 4 3 21

RED

RED/BLK
COM

BLU

GEN/YEL

BLU/WHT

JUMPER
INSTALLED
INITIALLY

YES

JUMPER
INSTALLED
INITIALLY

NO*

YES

JUMPER
INSTALLED
INITIALLY

YES

C713
059899-33
12/9/13

START RELAY
(047702-27)

RELAY

EQUIPMENT
GROUND

START CAP.

BROWN
S
BROWN
BLACK R
RUN CAPACITOR
BLEED RESISTOR
052396-1

BLUE
ABOVE ELECTRICAL DIAGRAM SHOWS WIRING NECESSARY
TO HOOK UP A COMPRESSOR USING A STAR T AND RUN
CAPACITOR (CSR) WITH A RELAY.

BLACK

WHITE
LINE

RUN
CAP.

RELAY

10
LINE

INTERNAL OVERLOAD
WHITE(120 VOLTS)
BLACK(230 VOLTS)

COMPRESSOR
TERMINAL
COVER

C S

START CAPACITOR
(047703)
11

START CAPACITOR

FIG. 2

BLACK INTERNAL

WINDING PROTECTOR
(INTERNAL)

FIG. 1

EXTERNAL EQUIPOTENTIAL
GROUND
GROUND

COMPRESSOR WIRING
(MODEL TL3G W/HST)

LEESON BEATER MOTOR WIRING
STEPS:
1) DISCONNECT WIRE T7 FROM TERMINAL 3
2) SPLICE BLUE WIRE AS SHOWN

L1 N

(+5v)
CLR
)
(GRD
GRN

BRN

BLU

GRN
WHT
RED
BLK

BLK
J5 J19

1 234
4

J13
J1
A

J11
J12

USE T3 AND L3 WHEN CP
CONTACTS ARE NOT AVAILABLE
BLACK
T2
L2

BLU

FIG. 3

BLK

J18
L1

GRN/YEL

BLK

CABLE

WHT

BLK

WHT
BLK

FUSE
15A

WHT
BLK

OPTIONAL
WHT

BLK

GRN/YEL

LEFT SYRUP HEATER
SEE FIG. 4

BEATER
INTERLOCK
RELAY

WHT/ORN

1
9

ORN

WHT

BRN

O.T.
WHT

WHT

FIG .4

WHT
GRN/YEL

BLK

GRN/YEL
BEATER MOTOR
STARTER
L
E
/Y
G

GRN/YEL

RED

BLK T2

GRN/YEL

RED
WHT
M
CONDENSER
BLOWER MOTOR
AIR COOLED

BLK

WHT

WATER COOLED
CONDENSER FAN

BRN

CABLE

BEATER MOTOR
SOFT SERVE
STARTER
COMPRESSOR
BLK
L2
T2
M
COMPRESSOR
CONTACTOR
GRN/YEL

SEE FIG. 2

BLK

SEE FIG. 3
SOFT SERVE
BEATER MOTOR

WHT

BLK

GRY/WHT

WHT

SYRUP HEATER

BLU

BLK
BLK
BARREL LIQUID
SOLENOID

THERMOSTA
190 F OPEN
140 F CLOSE
WHT

BLACK

BLK

RED

C0M

8
14

BEATER
MOTOR
INTERLOCK
N.O. SWITCH

GRN/YEL

WHT
BRN

C
L

BEATER
MOTOR
STARTER
COIL

BLK

BEATER
MOTOR
OVERLOAD
SWITCH

5
4

12
13

BLK

BLK
BLK

WHT/ORN

WHITE

96 95

BLK

RED
COMPRESSOR
CONTACTOR
COIL

BLK

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

BLU

BLK

BLK
OFF

PANEL
JACK

T4 OR YELLOW INTERNAL

BLU/WHT

BA
J14

8 7 6 5 4 3 21J10 10 9 8 7 6 5 4 3 21

2
1

1 23 456 7

5 3 1 1 23 4567

BLK

J9 OR BLACK INTERNAL

240

BLU/WHT

BLK

BLK
BLK

BLK/WHT

OFF

BLUE

WHT/RED

BLK
BLK

BLK/WHT

GRN/YEL

GRN
CLR
CABLE
2
1

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A.
J7

YEL

BLK

SELF-SERVICE
ENABLE

(OPTIONAL)
BARRELHOPPER
--THERMISTOR PROBES--

WHT/RED
ON BLK/WHT

CABLE

RIBBON
CABLE

YEL
BLK

MIX
LOW
PROBE

GND
+5V
J20

DISABLE ENABLE
SV CABLE

BLUE
4

24 VAC

BRN

BLU
RED

SV CABLE

PRP

MIX
OUT
PROBE

BLACK

T1 OR BLUE INTERNAL
T8 OR RED INTERNAL

BLK/RED

ORN/WHT
RED/BLK
PRP

YEL

1
OFF

DRAW
SWITCH

WHT

RIBBON CABLE
RED
BLU

RED
BLU

DRAW
SWITCH

GE/RBC/MARATHON BEATER MOTOR WIRING
NOTE: FOR CCWLE - BLUE INTERNAL ON #1,YELLOW INTERNAL ON #2

BEATER MOTOR
CONTACTOR

COM

ORN/WHT

BLU/WHT

T3
L3
USE T3 AND L3 WHEN
CP CONTACTS ARE NOT AVAILABLE
BLACK T2
L2

SV CABLE

BLU

J12 OR PURPLE INTERNAL

GRN/YEL

COM

RED

+5V

RIBBON CABLE
RED
BLU

GRN/YEL

J11

SV CABLE

HOPPER
GROUND

J10

CLR

OUT

BLK

RED
BLU

POWER
SWITCH
3PDT

OPTIONAL REAR
MIX LEVEL LIGHTS

GRD

J17

2 4 6 8 10
1 3 5 7 9

J12

1 23

J13

2 4 6 8 10
1 3 5 7 9

SV CABLE

WHT

RED

BLK

ORN
RED

J15

GRN/YEL

BLK

RIBBON CABLE

J16

UNIVERSAL CONTROL PCB A.

WHT

4 56

BLK

BLU

16V

ELECTRICAL
ENCLOSURE

WHT

BLK/RED

INTERFACE BOARD
POWER TRANSFORMER

BLUE

RIBBON CABLE

NOT
CONNECTED

CABLE

240V

BLUE

BLU

WHT

L1 LINE L2
EMI FILTER
L1 LOAD L2

BLACK

GRN/YEL

GRN/YEL
BLK

BEATER MOTOR
CONTACTOR

BLK

BLK/RED

- 8 LEDS
USER
J1
- LCD SCREEN
INTERFACE
- 9 KEYS
J2
BOARD
J3
- BEEPER

RED (+5v)
BLK (GRD)

BLK/RED

SV CABLE

BRN

GRN/YEL

TERMINAL BLOCK
BLK

BLK

YELLOW INTERNAL

START WINDING

MAIN WINDING

T3
L3
USE T3 AND L3 WHEN
CP CONTACTS ARE NOT AVAILABLE
BLACK
T2
L2

SCHEMATIC WIRING DIAGRAM - CSR

BRN
WHT
M
FAN
BRN
10 14
START RELAY 11
13 COMP

BRN

LEFT SIDE
CONTROL
RIGHT SIDE
CONTROL

GRN/YEL

BLU

START CAP
MIX REF. SYSTEM
(DANFOSS TL3G COMPR.)
SEE FIG. 1

ELECTRICAL
ENCLOSURE

BLU

GRN/YEL

BLU

BRN

GRN/YEL

L1 N
TERMINAL BLOCK
BLK

BLK

BLU
BLK

BLU/WHT

BRN

SV CABLE

J3
RED/BLK

1 23456 7

BLK

J18

5 3 1 1 234567

0
1 WHT

WHT

BLK

BLK
FUSE
15A

WHT
OPTIONAL

BLK

BLU/WHT

BLK

BLU/WHT

WHT
GRN/YEL

RIGHT SYRUP HEATER
SEE FIG. 4

WHT/ORN

BEATER
INTERLOCK
RELAY

WHT/ORN

WHT

BLK

WHT

BLK
BLK

BLK

C0M

WHT

GRY/WHT
SOFT SERVE
COMPRESSOR
L1

SEE FIG. 2

BEATER MOTOR
STARTER
BLK

SEE FIG. 3
SOFT SERVE
BEATER MOTOR
BLK T2
M

BEATER MOTOR
STARTER

COMPRESSOR
CONTACTOR

GRN/YEL

BLK

GRN/YEL

BLK

GRN/YEL
GRN/YEL

PINS 1 AND 2

UVC4 BOARD

DOMESTIC CONFIGURATION - JUMPER
INSTALLED. HOPPER TEMPERATURE NOT
DISPLAYED ON SCREEN/HEAT SYMBOL KEYS
ONLY ACTIVE WHEN A LOCKOUT CONDITION
HAS OCCURRED/STANDBY KEYS DISABLED.

INTERNATIONAL CONFIGURATION - NO JUMPER
INSTALLED. HOPPER TEMPERATURES
DISPLAYED ON SCREEN/MANUAL HEAT CYCLE
START BY SELECTING HEAT SYMBOL/STANDBY
KEYS FUNCTIONAL.

FUNCTION

RESERVED (DO NOT USE)

PINS 1 AND 2

RESERVED (DO NOT USE)

JP1

JP3

RESERVED (DO NOT USE)

NO JUMPER INSTALLED - NO LOCKOUT DURING
AUTO/STANDBY IF BARREL OR HOPPER IS TOO
WARM FOR A PERIOD OF TIME.

JP4

FUNCTION

RESERVED (DO NOT USE)

JUMPER INSTALLED - FORCE BRUSH CLEAN
STATUS.
JUMPER INSTALLED - ACTIVATES SYRUP
HEATERS

RESERVED (DO NOT USE)

JP5

PINS 3 AND 4

JP6

RESERVED (DO NOT USE)

JUMPER INSTALLED DISABLES RESET.

JP2

JP7

LEFT
INTERFACE
BOARD

RTCK

DBGEN

RESERVED (DO NOT USE)

PINS 7 & 8

JUMPER
INSTALLED
INITIALLY

YES

JUMPER
INSTALLED
INITIALLY

NO*

J10

YES

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

JUMPER
INSTALLED
INITIALLY

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

FUNCTION

RESERVED (DO NOT USE)

YES

RIGHT
INTERFACE
BOARD

RESERVED (DO NOT USE)

JUMPER INSTALLED - ENABLES 59F HOPPER
TEMPERATURE CHECK.

RESERVED (DO NOT USE)

YES

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

JUMPER INSTALLED - REDUCED MIX LOW
SENSITIVITY.
JUMPER INSTALLED - REDUCED MIX OUT
SENSITIVITY.

2. RED WIRE ON RIBBON CABLES MUST BE
CONNECTED TO PIN 1 AT EACH END.

DRAW
SWITCH

BARREL LIQUID
SOLENOID

NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY
TOUCHING GROUNDED UNIT BEFORE
HANDLING SOLID STATE COMPONENTS.

RED

BLK

WHT

C
L

BEATER
MOTOR
STARTER
COIL

8
14

BLK

BEATER
MOTOR
OVERLOAD
SWITCH

5
4

12
13

BLK

WHT/ORN

ORN

BLK

96 95

BLK

RED
COMPRESSOR
CONTACTOR
COIL
WHT

BLU

BLK

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

* IF THE UNIT HAS THE INTEGRAL SYRUP OPTION-405, THEN THIS
JUMPER SHOULD BE INSTALLED.

GROUND FRAME SECURELY

BLK

PANEL
JACK

BLK

1 234

J13
J1
A

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A.

BLK
CABLE

CLR

J19

J14

BLK

2
1

BLK
BLK

BARRELHOPPER
--THERMISTOR PROBES--

GND
+5V
J20

YEL

BLK

MIX
LOW
PROBE

YEL
BLK

GRA/BLK
PRP/WHT
MIX
OUT
PROBE

PRP/WHT

BLK

J11
J12

8 7 6 5 4 3 21J10 10 9 8 7 6 5 4 3 21

BLU

DRAW
SWITCH

RED

GRN/YEL
RED/BLK
COM

BLK

RED
BLU

GRN/YEL

RIBBON
CABLE

RED
BLU

RED
BLU
GRN/YEL

BLK

GEN/YEL

BLU/WHT

C713
059899-40
12/9/13

(+5v)
CLR
)
(GRD
GRN

WHT

GRN
WHT
RED
BLK

OUT

J10

J11
+5V

RIBBON CABLE

RIBBON CABLE
RED
BLU

RED
BLU

BLK

BLU

BLU/WHT

BLU

BLK

GRN/YEL

BLK

BLK
J5 J19

1 234
4

BLK

J18

WHT

BA
J14

J13
J1
B

BLK

BLK/WHT

WINDING PROTECTOR
(INTERNAL)
COMPRESSOR WIRING
(MODEL TL3G W/HST)

BLK

GRN/YEL
M BLKT2

WHT

BLK
BLK

GRN/YEL

COMPRESSOR
CONTACTOR
GRN/YEL

CONDENSER
BLOWER MOTOR
WHT
RED
M
AIR COOLED

L
E

WHT

GRN/YEL

BLK

WHT

WATER COOLED
CONDENSER FAN

BRN

RED

BLK

GRN/YEL

WHT

BLK

SOFT SERVE
COMPRESSOR
T2
L2
M

BLU

BLK

BEATER MOTOR
STARTER

GRY/WHT

BLK

BEATER MOTOR
STARTER
BARREL LIQUID
SOLENOID

BLK

BRN

BLACK

GRN/YEL

WHT

BLK

SOFT SERVE
BEATER MOTOR

8
14

BEATER
MOTOR
INTERLOCK
N.O. SWITCH
BLK

WHT

BRN

BLK
BLK

5
4

12
13

BLU

BLK

BEATER
MOTOR
STARTER
COIL

BLK

RED
COMPRESSOR
CONTACTOR
COIL

BLK

BLK
BLK

WHT/ORN

ORN

BLK

START WINDING

MAIN WINDING
BEATER
INTERLOCK
RELAY

WHT/ORN

BEATER
MOTOR
OVERLOAD
SWITCH

RED

WHT
GRN/YEL

WHITE

96 95

GRN/YEL

BLK
WHT

OPTIONAL

LEFT SYRUP HEATER
SEE FIG. 2

BLK

C
L

BLU

FUSE
15A

WHT/ORN

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH

C0M

PANEL
JACK

13
14

WHT

BLK

BLK
BLU/WHT

1 23456 7

WHT

BLK

OFF

DRAW
SWITCH

2
1

BLK

BLK
BLK

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

BLK
BLK

5 3 1 1 234567

START CAPACITOR
(047703)
11

WHT/RED

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A.

BARREL HOPPER (OPTIONAL)
--THERMISTOR PROBES--

BLK/WHT

OFF

CABLE

BLUE

BLU/WHT

BLK

SV CABLE
WHT/RED

ON BLK/WHT

START RELAY
(047702-27)

BLU
24 VAC

BLK

2
1

SELF-SERVICE
ENABLE
DISABLE ENABLE

RED

OFF

GRN
CLR
CABLE

YEL

BLK

MIX
LOW
PROBE

YEL
BLK

PRP

SV CABLE

MIX
OUT
PROBE

RED/BLK
PRP

YEL

J11
J12

8 7 6 5 4 3 21J10 10 9 8 7 6 5 4 3 21

DRAW
SWITCH

COM

GND
+5V
J20

BRN

GRN/YEL

BLK

FIGURE 1
240

BLU/WHT

RED

ORN/WHT

POWER
SWITCH
3PDT

BLK
BLU

SV CABLE

BLK/RED
WHT
COM

GRN/YEL

HOPPER
GROUND

CABLE

J1
21

CLR

RIBBON
CABLE

BLU
RED

J17

BLK

WHT

GRD

UNIVERSAL CONTROL PCB A.

BEATER MOTOR LINE MUST
PASS TWICE THRU THE
SENSOR CORE.

OPTIONAL REAR
MIX LEVEL LIGHTS

1 23

4 56

J13

J15

SV CABLE

WHT

RED

ORN
RED

J16

J12

BLK

WHT

2 4 6 8 10
1 3 5 7 9

BLU

RIBBON CABLE

2 4 6 8 10
1 3 5 7 9

16V

FIG .2

ELECTRICAL
ENCLOSURE

RIBBON CABLE

BLK/RED

INTERFACE BOARD
POWER TRANSFORMER

WHT

CABLE

240V
NOT
CONNECTED

O.T.
WHT

WHT

SYRUP HEATER

WHT

L1 LINE L2
EMI FILTER
L1 LOAD L2

BLK

THERMOSTA
190 F OPEN
140 F CLOSE
WHT

GRN/YEL

GRN/YEL
BLK

EQUIPOTENTIAL
GROUND

EXTERNAL
GROUND

WHT

BLK/RED

BLK (GRD)

BLK/RED

- 8 LEDS
USER
J1
INTERFACE - LCD SCREEN
- 9 KEYS
J2
J3 BOARD
- BEEPER

RED (+5v)

SV CABLE

BRN

GRN/YEL

TERMINAL BLOCK
L1 L2 L3 N
BLK

BRN
WHT
M
FAN

BRN

BRN
START RELAY

10 14
11 13

CABLE
GRN/YEL

COMP

LEFT SIDE
CONTROL

START CAP
MIX REF. SYSTEM
(DANFOSS TL3G COMPR.)
(ALSO SEE FIG.2)

RIGHT SIDE
CONTROL

BLU

TERMINAL BLOCK

1 23456 7

BLK
WHT

FUSE
15A

BLK

BLU/WHT

GRN/YEL

WHT

WHT
GRN/YEL

RIGHT SYRUP HEATER
SEE FIG. 2

BEATER
INTERLOCK
RELAY

WHT/ORN

ORN

WHT

BLK

WHT
WHT

BLK

BEATER
MOTOR
STARTER
COIL

BLK

BLK
BLK

BEATER
MOTOR
OVERLOAD
SWITCH

5
4

BLK

WHT/ORN

BLK

96 95

RED
COMPRESSOR
CONTACTOR
COIL
WHT

BLU

BLK

PANEL
JACK

RED

BLK

BLK
OPTIONAL

COMPRESSOR
HIGH PRESSURE
LIMIT SWITCH

BLK

C0M

GRN/YEL

WHT

BLK

C
L

WHT

BLK
BLK

BLK

GRY/WHT

BARREL LIQUID
SOLENOID

WHT

BLK
BLK

BEATER MOTOR
STARTER
BLK

SOFT SERVE
COMPRESSOR
GRN/YEL
L1

BLK
BLK

COMPRESSOR
CONTACTOR

GRN/YEL

PINS 1 AND 2
DOMESTIC CONFIGURATION - JUMPER
INSTALLED. HOPPER TEMPERATURE NOT
DISPLAYED ON SCREEN/HEAT SYMBOL KEYS
ONLY ACTIVE WHEN A LOCKOUT CONDITION
HAS OCCURRED/STANDBY KEYS DISABLED.

INTERNATIONAL CONFIGURATION - NO JUMPER
INSTALLED. HOPPER TEMPERATURES
DISPLAYED ON SCREEN/MANUAL HEAT CYCLE
START BY SELECTING HEAT SYMBOL/STANDBY
KEYS FUNCTIONAL.

FUNCTION

RESERVED (DO NOT USE)

UVC4 BOARD

RESERVED (DO NOT USE)

PINS 1 AND 2

JP3

RESERVED (DO NOT USE)

JP1

JP4

JUMPER INSTALLED DISABLES RESET.

NO JUMPER INSTALLED - NO LOCKOUT DURING
AUTO/STANDBY IF BARREL OR HOPPER IS TOO
WARM FOR A PERIOD OF TIME.

JP5

RESERVED (DO NOT USE)

FUNCTION

RESERVED (DO NOT USE)

JUMPER INSTALLED - FORCE BRUSH CLEAN
STATUS.
JUMPER INSTALLED - ACTIVATES SYRUP
HEATERS

RESERVED (DO NOT USE)

JP6

RESERVED (DO NOT USE)

PINS 3 AND 4

JP7

JP2

RTCK

LEFT
INTERFACE
BOARD

DBGEN

RESERVED (DO NOT USE)

FUNCTION

PINS 7 & 8

RESERVED (DO NOT USE)

J10

JUMPER INSTALLED - ENABLES 59F HOPPER
TEMPERATURE CHECK.

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

RESERVED (DO NOT USE)

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

RESERVED (DO NOT USE)

RIGHT
INTERFACE
BOARD

SOFT SERVE
0-6 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

JUMPER INSTALLED - REDUCED MIX LOW
SENSITIVITY.
JUMPER INSTALLED - REDUCED MIX OUT
SENSITIVITY.

SOFT SERVE
0-12 AMP BEATER MOTOR AMPERAGE RANGE
PERSONALITY BOARD

* IF THE UNIT HAS THE INTEGRAL SYRUP OPTION-405, THEN THIS
JUMPER SHOULD BE INSTALLED.

NOTE:
1. STATIC ELECTRICITY MAY CAUSE
DAMAGE TO SOLID STATE COMPONENTS.
ELIMINATE STATIC ELECTRICITY BY
TOUCHING GROUNDED UNIT BEFORE
HANDLING SOLID STATE COMPONENTS.

BLK

M BLKT2

BEATER MOTOR
STARTER

GRN/YEL

BLK

GRN/YEL

BLK

WHT

SOFT SERVE
BEATER MOTOR

2. RED WIRE ON RIBBON CABLES MUST BE
CONNECTED TO PIN 1 AT EACH END.

GROUND FRAME SECURELY

ADDITIONAL DRAW SWITCH
FOR FLAVORBURST

GRN/YEL

CABLE

J18

INTFC PCB A.
WITH SOFT SERVE
PERSONALITY PCB A. 0
1
5 3 1 1 234567

BLK

J5 J19

1 234

J14

J13
J1
A

BLK

CLR

RED/BLK

BLK

BLU/WHT

DRAW
SWITCH

BLK

2
1

BLK
BLK

2
4
BARRELHOPPER
--THERMISTOR PROBES--

GND
+5V
J20

YEL

MIX
LOW
PROBE

BLK

YEL
BLK

MIX
OUT
PROBE

PRP/WHT

GRA/BLK
PRP/WHT

BLK

DRAW
SWITCH

J11
J12

8 7 6 5 4 3 21J10 10 9 8 7 6 5 4 3 21

BLK
WHT

RED

RED/BLK
COM

BLK

WHT
BLK

BLK

GRN/YEL

RIBBON
CABLE

GEN/YEL

BLU/WHT

RED
BLU

WHT

SV CABLE

BLU/WHT

GRN/YEL

ELECTRICAL
ENCLOSURE

BEATER MOTOR LINE MUST
PASS TWICE THRU THE
SENSOR CORE.

BLU/WHT

WHT

BLU

BRN

BLK

L1 L2 L3 N

JUMPER
INSTALLED
INITIALLY

YES

JUMPER
INSTALLED
INITIALLY

NO*

YES

JUMPER
INSTALLED
INITIALLY

YES

C713
059899-58
12/9/13

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : No
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Copy, Annotate, Fill forms, Extract, Print high-res
Author                          : t165411
Create Date                     : 2013:11:21 13:31:45-06:00
Modify Date                     : 2014:08:26 11:45:53-05:00
Title                           : 
Has XFA                         : No
XMP Toolkit                     : Adobe XMP Core 5.2-c001 63.139439, 2010/09/27-13:37:26
Metadata Date                   : 2014:08:26 11:45:53-05:00
Creator Tool                    : PScript5.dll Version 5.2.2
Format                          : application/pdf
Creator                         : t165411
Document ID                     : uuid:085fcb16-5290-4ec5-9131-c058f65e62a3
Instance ID                     : uuid:52efe7fa-ddad-4748-a482-1350f1b3e6a3
Producer                        : Acrobat Distiller 10.1.1 (Windows)
Page Count                      : 50

EXIF Metadata provided by EXIF.tools

Taylor Refrigerator C713 Users Manual

C713 to the manual c366bf7b-dd05-4737-8313-02f5310faef7

Navigation menu

Versions of this User Manual:

Views

Navigation