Technical Solutions ZRC01 ZIGBEE REMOTE CONTROL User Manual Visio User Guide2 vsd
Technical Solutions Inc ZIGBEE REMOTE CONTROL Visio User Guide2 vsd
Users Manual
1) The zCO01 Coordinator unit is installed first. Locate a 120vac output in the
approximate physical center of the zRY01 units to be installed in the attic. It is
important that the Coordinator unit be able to communicate with at least one of the
Relay unit(s) located in the attic. Plug the Coordinator into the 120VAC outlet on
one of the floors, not in the attic.
2) Setting up the zRC01 Remote Control.
a) Insert the batteries
b) Leds “1 - 6” will flash quickly
c) after a few seconds, Leds “1 - 6” stop flashing.
This confirms the Remote Control has linked to the Coordinator.
3) The zRY01 Relay units are installed next.
Plug the first zRY01 into the 120VAC outlet closest to the Coordinator. Plug the
Fan into the outlet on the zRY01. Allow approx 15 seconds for the zRY01 unit to
connect to the Coordinator.
Test the link with the Remote Control:
a) Press and hold the All button for 2 seconds, then release
b) Leds “1 - 6” will flash quickly
c) after a few seconds, the “1” led and the “1:00” led should light,
this means the zRY01 unit will be controlled with button “1”
d) Press the On button, the zRY01 unit should switch on
e) Press the “1” button, the led will go off
f) Press the Clear button, the zRY01 unit should switch off
The zRY01 unit is working with button “1”.
4) Plug each of the zRY01 units in one at a time, and follow the same procedure for
each as in step 3) above, testing each zRY01 unit, before installing the next. As
each zRY01 is added to the network, the next Fan select button is used.
This product provides convenient control of the QuietCool fans, from inside the
home. The Wireless Fan Control system consists of 3 units:
1) The zRC01 Remote Control is used to set fans on and off, or to set a fan or
group of fans on for a timed duration.
2) The zCO01 Coordinator runs the wireless network. **Only one zCO01 allowed
per network**
3) The zRY01 Relay units switch the Fan power on and off. One zRY01 is used
per Fan, a maximum of 6 zRY01 per network are allowed.
**more than one Coordinator in a network will cause the network to fail
Copyright 2008 Technical Solutions Inc, 7787 Progress Way, Delta, BC
1-888-TECHSOL - 604-946-8324 - www.Techsol.com
6
5
4
3
2
1
All
On
:10
:30
1:00
3:00
5:00
Clear
The zRC01 Remote Control is used to set a fan, or a group of Fans, on or off.
It can also set the Fans on for a predetermined amount of time.
1) The Remote Control goes into sleep mode when the switches are not pressed for
a period of time. To wake up the Remote Control, press the All switch.
The “1-6” Leds will light to indicate which zRY01 units are ready to use.
2) Select the Fan(s) to be controlled, using the “1-6” switches. An LED lights on to
indicate the selected Fan(s). Any combination of Fans can be selected, by pressing
the “1-6” switches, each switch press toggles the Fan select on and off.
The All switch can be used to select all available Fans.
3) To set the selected Fans on, press any of the timer switches (:10 to 5:00), to set
the selected Fan(s) on, for that timed period. Or press the On switch to set all
selected Fans on, with no timer.
4) To set the selected Fans off, press the Clear switch.
zPoint Products Wireless Fan Control system
Installation instructions
Remote Control operationDescription
On, Off &
Timed On
switches
Sets all
Timer and
On LEDS
to off and
sets all
selected
Fan units
off
Fan Select
switches
zCO01 power requirement: 100-130VAC, 60 Hertz, 5 watts
zRY01 power requirement: 100-130VAC, 60 Hertz, 5 watts
Switch capacity: Max 1/3HP or 7 Amps at 120VAC
zRC01 power requirement: 2 x AA Batteries
Specifications
These devices comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) these devices may not cause harmful interference, and
(2) these devices must accept any interference received, including interference that may cause undesired
operation.
ETL Certification …..
The zPoint zCO01 and zRY01 products have been thoroughly tested by Intertek, a
nationally recognized independent third-party testing laboratory. Products bearing
the ETL Listed mark signify that the product has been tested to and has met the
requirements of a consensus of US product safety standards, that the manufacturing
site has been audited, and that the manufacturer has agreed to a program of
quarterly factory follow-up inspections to verify continued conformance.
FCC Certification …..
ETL Certification
FCC Certification
Copyright 2008 Technical Solutions Inc, 7787 Progress Way, Delta, BC
1-888-TECHSOL - 604-946-8324 - www.Techsol.com
NOTE:
1. This device complies with Part 15 of the FCC rules. Operations subject to the following two conditions:
(i)This device may not cause harmful interference, and
(ii) This device must accept any interference received, including interference that may cause undesired operation.
2. The Manufacturer is not responsible for any Radio or TV interference caused by unauthorized modifications to this equipment. Such modification could void the
user's authority to operate the equipment.