Technicolor Delivery Technologies Belgium TG590 Broadband Home Router User Manual Safety MASTER

Download:
Mirror Download [FCC.gov]
Document ID	1388211
Application ID	LZM34EJEH3/TAn0HvRxEug==
Document Description	User Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	15.7kB (196195 bits)
Date Submitted	2010-12-09 00:00:00
Date Available	2010-12-09 00:00:00
Creation Date	2010-10-13 15:27:44
Producing Software	Acrobat Distiller 9.4.0 (Windows)
Document Lastmod	2010-12-08 09:07:48
Document Title	Safety_MASTER.book
Document Creator	FrameMaker 8.0
Document Author:	ClauwaertJ

Safety Instructions and Regulatory Notices
Wall Mount Instructions
Read this document prior to installation!
PAP
Copyright 2010 Technicolor. All rights reserved.
All tradenames referenced are service marks, trademarks, or registered trademarks of their respective companies. Specifications subject to change without notice.
E-DOC-SAF-20100819-0001 v0.4. Printed in China.
*DSL123456789*
DSL123456789
inch
Use this template to drill holes in the wall for wall mounting the device.
1/2
1/4 inch
+- 1/3 inch
SAFETY INSTRUCTIONS AND REGULATORY NOTICES
BEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ THESE INSTRUCTIONS
When using this product, always follow the basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the
following:
 Always install the product as described in the documentation that is included with your product.
 Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.
 Do not use this product to report a gas leak in the vicinity of the leak.
Wireless
In case this product is equipped with a wireless transceiver, it uses Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division
Modulation (OFDM) radio technology. As such it is designed to be inter-operable with any other wireless DSSS/OFDM type product that:
 Complies with the IEEE802.11b/IEEE802.11g/IEEE802.11n Standard on Wireless LANs, as defined and approved by the Institute of Electrical and
Electronics Engineers.
 Is Wi-Fi® CERTIFIED™ as defined by the Wi-Fi® Alliance.
Directive
Unless express and prior approval by Technicolor in writing, you may not:
 Disassemble, de-compile, reverse engineer, trace or otherwise analyse the equipment, its content, operation, or functionality,
or otherwise attempt to derive source code (or the underlying ideas, algorithms, structure or organization) from the equipment,
or from any other information provided by Technicolor, except to the extent that this restriction is expressly prohibited by local law;
 Copy, rent, loan, re-sell, sub-license, or otherwise transfer or distribute the equipment to others;
 Modify, adapt or create a derivative work of the equipment;
 Remove from any copies of the equipment any product identification, copyright or other notices;
 Disseminate performance information or analysis (including, without limitation, benchmarks) from any source relating to the equipment.
Such acts not expressly approved by Technicolor will result in the loss of product warranty and may invalidate the user's authority to operate this
equipment in accordance with FCC Rules.
Technicolor disclaims all responsibility in the event of use that does not comply with the present instructions.
Safety Instructions
Climatic conditions
This product:
 Is intended for in-house stationary desktop use; the maximum ambient temperature may not exceed 40°C (104°F).
 Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.
 Must not be exposed to heat trap conditions and must not be subjected to water or condensation.
 Must be installed in a Pollution Degree 2 environment (Environment where there is no pollution or only dry, nonconductive pollution).
Cleaning
Unplug this product from the wall socket and computer before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Water and moisture
Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool.
Transition of the product from a cold environment to a hot one, may cause condensation on some of its internal parts. Allow it to dry by itself before restarting the product.
Interface classifications
The external interfaces on the rear panel of the product are classified as follows:
 All interface ports (e.g. Coax, Ethernet, 10/100Base-T/MDI(-X), USB, etc.), including the low voltage power input from the AC mains power
supply: SELV circuits.
WARNING
It is not allowed to connect the Coax port to a cable distribution or cable television network by any means, e.g. with a coaxial cable.
Electrical powering
The powering of the product must adhere to the power specifications indicated on the marking labels.
The power supply must be Class II and a Limited Power Source in accordance with the requirements of IEC60950-1/ EN60950-1, Clause 2.5 and rated
as indicated on the label on your product. It must be tested and approved to national or local standards.
For US and Canada: This product is intended to be supplied by a Listed Direct Plug-in, or Desktop Power Unit marked "Class 2" and rated as indicated
on the label on your product.
The use of other types of supplies is prohibited. If you are not sure of the type of power supply needed, consult the product's user documentation or
contact your local product dealer.
USB
The device is to be connected to an identified USB port complying with the requirements of a Limited Power Source.
Accessibility
The Direct Plug-in power supply, or the plug on the power supply cord serves as disconnect device. Be sure that the power socket outlet you plug the
power supply into is easily accessible and located as close to the equipment as possible.
1 Place the template from the previous page on the wall in the position the gateway will be
mounted.
Note: It is recommended that the connectors on the gateway’s backpanel are facing down.
2 Mark the mounting holes. The distance between the drilled holes must be exactly 190mm (7.5
inches) as indicated on the template.
3 Drill the marked holes with a 6mm (0.24 inches) diameter drill bit.
4 Insert the wall plugs in the drilled holes.
5 Insert the screws in the wall plugs and leave the screw extented about 5mm (0.2 inches) from
the wall.
6 Hang the gateway on the screws.
Wall Mount instructions
Overloading
Do not overload mains supply socket outlets and extension cords as this increases the risk of fire or electric shock.
Servicing
To reduce the risk of electric shock, do not disassemble this product. None of its internal parts are user-replaceable; therefore, there is no reason to
access the interior. Opening or removing covers may expose you to dangerous voltages. Incorrect reassembly could cause electric shock if the
appliance is subsequently used.
If service or repair work is required, take it to a qualified service dealer.
Damage requiring service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:
 When the power supply or its plug are damaged.
 When the attached cords are damaged or frayed.
 If liquid has been spilled into the product.
 If the product has been exposed to rain or water.
 If the product does not operate normally.
 If the product has been dropped or damaged in any way.
 There are noticeable signs of overheating.
 If the product exhibits a distinct change in performance.
Immediately disconnect the product if you notice it giving off a smell of burning or smoke. Under no circumstances must you open the equipment
yourself; you run the risk of electrocution.
North-America - Canada
Notification of Canadian Radio Frequency Interference Statement
This Class B digital apparatus complies with Canadian ICES-003.
NOTICE: This product meets the applicable Industry Canada technical specifications.
Canada - Industry Canada (IC)
In case this product is equipped with an IEEE802.11b/IEEE802.11g/IEEE802.11n wireless transceiver, complying with RSS 210 and/or RSS 213 of
Industry Canada, operation is subject to the following two conditions:
1 This device may not cause harmful interference.
2 This device must accept any interference received, including interference that may cause undesired operation of the device.
IMPORTANT NOTE: Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and
operated with minimum distance 20cm between the radiator and your body.
Restricted Frequency Band
In case this product is equipped with an IEEE802.11b/IEEE802.11g/IEEE802.11n wireless transceiver, it only uses channels 1 to 11 (2412 to 2462 MHz) on
Canada territory.
Regulatory Information
You must install and use this device in strict accordance with the manufacturer's instructions as described in the user documentation that is included
with your product.
Before you start installation or use of this product, carefully read the contents of this document for device specific constraints or rules that may apply in
the country where you want to use this product.
In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the
organization.
If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (e.g. airports), you are
encouraged to ask for authorization to use this device prior to turning on the equipment.
Technicolor is not responsible for any radio or television interference caused by unauthorized modification of the device, or the substitution or
attachment of connecting cables and equipment other than specified by Technicolor. The correction of interference caused by such unauthorized
modification, substitution or attachment will be the responsibility of the user.
Technicolor and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from failing to
comply with these guidelines.
North-America - United States of America
Federal Communications Commission (FCC) Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following measures:
 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
 Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1 This device may not cause harmful interference, and
2 This device must accept any interference received, including interference that may cause undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate
this equipment.
Responsible Party: Technicolor Inc., 10330 North Meridian Street, Indianapolis, IN 46290 USA, (580) 634-0151.
RF-Exposure Statement
When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation
distance of at least 20cm between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must
have a distance of at least 20cm from the product and must not lean on the product in case it is wall-mounted.
With a separation distance of 20cm or more, the M(aximum) P(ermissible) E(xposure) limits are well above the potential this module is capable to
produce.
The transmitter shall not be collocated with other transmitters or antennas.
Restricted Frequency Band
In case this product is equipped with an IEEE802.11b/IEEE802.11g/IEEE802.11n wireless transceiver, it may only use channels 1 to 11 (2412 to 2462
MHz) on U.S.A. territory.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Extract, Print high-res
XMP Toolkit                     : 3.1-701
Modify Date                     : 2010:12:08 09:07:48+08:00
Create Date                     : 2010:10:13 15:27:44+02:00
Metadata Date                   : 2010:12:08 09:07:48+08:00
Creator Tool                    : FrameMaker 8.0
Format                          : application/pdf
Title                           : Safety_MASTER.book
Creator                         : ClauwaertJ
Document ID                     : uuid:582ede18-b647-436f-a725-ee1727dd7c0a
Instance ID                     : uuid:72de8e7a-2d27-4761-8a2e-3871d524c957
Producer                        : Acrobat Distiller 9.4.0 (Windows)
Has XFA                         : No
Page Count                      : 4
Author                          : ClauwaertJ

EXIF Metadata provided by EXIF.tools