Technisonic TSC-4400 VHF/AM SINGLE CHANNEL TRANSCEIVER User Manual users manual

Technisonic Industries Limited VHF/AM SINGLE CHANNEL TRANSCEIVER users manual

users manual

VHF/AM SINGLE CHANNEL50 WATT TRANSCEIVERMODEL TSC-4400P/N 011211-1Installation and Operating InstructionsTiL Document No.04RE331Rev. n/cNovember 2004Technisonic Industries Limited240 Traders Blvd., Mississauga, Ontario L4Z 1W7 Tel:(905)890-2113 Fax:(905)890-5338web site: www.til.ca
WARNINGDo not make physical contact with antenna when transmitter is on. This unit can produce over 50 watts of power when transmitting.CAUTIONThis unit contains static sensitive devices. Wear a grounded wrist strap and/or conductive gloves whenhandling printed circuit boards.WARRANTY INFORMATIONThe rack mounted Single Channel Transceiver, Model TSC-4400 is under warranty for one year fromdate of purchase. Failed units caused by defective parts, or workmanship should be returned to:Technisonic Industries Limited240 Traders BlvdMississauga, Ontario L4Z 1W7 CANADATel: (905) 890-2113Fax: (905) 890-5338A Page
REVISIONSREV PAGE DESCRIPTION DATE APPROVED N/C Original Issue 11/04 RRHD
TABLE OF CONTENTSParagraph Title PageSECTION 1 GENERAL DESCRIPTION1.1 Introduction ............................................. 1-11.2 Description ............................................. 1-11.2.1 Transceiver Module ........................................ 1-21.2.2 Power Supply Module - P/N 043603-1 .......................... 1-21.2.3 RF Amplifier Modules - P/N 043604-1 (Model PA-50) ................ 1-21.2.4 Mother Board - P/N 033588-1 ................................ 1-21.2.5 Remote Control Boards ..................................... 1-21.2.6 Crystal Filter (Option 1) ..................................... 1-31.3 Modes of Operation ....................................... 1-31.3.1 Local/Remote Operation ..................................... 1-31.3.1.1 Conference Audio ......................................... 1-41.3.2 AC and DC Operation ...................................... 1-41.4 Technical Summary ........................................ 1-4SECTION 2 PREPARATION FOR USE AND STORAGE2.1 Introduction ............................................. 2-12.2 Disassembly/Assembly ..................................... 2-12.2.1 Remove/Replace Cover Assembly .............................. 2-12.2.2 Remove/Replace Transceiver Module ............................ 2-12.2.3 Remove/Replace Memory Set Board Module A5A1 .................. 2-32.2.4 Remove/Replace Control Board ................................ 2-32.2.5 Remove/Replace Crystal Filter Board, P/N 923069 .................. 2-52.3 Channel Frequency Programming .............................. 2-52.3.1 Introduction ............................................. 2-52.3.2 Frequency Range ......................................... 2-52.3.3 Frequency Programming Requirements .......................... 2-52.3.4 Programming a Frequency ................................... 2-72.4 Remote Operation Set Up ................................... 2-82.4.1 Remote Control Board P/N 923051-1 ........................... 2-92.4.2 Remote Control Board P/N 943180-1 .......................... 2-102.5 Optional Loudspeaker, Headphone Installation .................... 2-132.5.1 External Loudspeaker ..................................... 2-132.5.2 Headset ............................................... 2-132.6 Transceiver Adjustments and Settings ......................... 2-132.7 Operational Check ........................................ 2-132.8 Storage ............................................... 2-13i
TABLE OF CONTENTS (Continued)Paragraph Title PageSECTION 3 OPERATING INSTRUCTIONS3.1 Introduction ............................................. 3-13.2 Installation .............................................. 3-13.3 Operator's Switches, Controls and Indicators ...................... 3-13.4 Operating Instructions ...................................... 3-53.4.1 Transmitter Operation (Local Mode) ............................. 3-53.4.2 Receiver Operation (Local Mode) ............................... 3-63.4.3 Switching OFF ........................................... 3-63.4.4 External DC Operation ...................................... 3-7LIST OF TABLES Table No. Title Page1-1 TSC-4400 Configurations .....................................1-11-2 TSC-4400 Leading Particulars ..................................1-52-1 ICAO Frequency Pairing Plan ...................................2-62-2 Remote Control Connector Functions ..............................2-82-3 Remote Control Board P/N 923051-1 Settings .......................2-92-4 Remote Control Board P/N 943180-1 Settings ...................... 2-103-1 Operator's Switches, Controls and Indicators ........................3-3LIST OF ILLUSTRATIONSFigure No. Title Page2-1 Single Channel Transceiver - Internal View ..........................2-22-2 Programming Adapter / Crystal Filter Board .........................2-42-3 Remote Control Board P/N 923051-1 ............................ 2-112-4 Remote Control Board P/N 943180-1 ............................ 2-122-5 Transceiver Adjustments and Settings ............................ 2-143-1 Single Channel Transceiver Controls and Indicators ....................3-2ii
1-1SECTION 1GENERAL DESCRIPTION1.1 INTRODUCTIONThis publication provides general information on the VHF/AM Single Channel Transceivers,Model TSC-4400, Part No. 011211-1, manufactured by Technisonic Industries Limited. Thisdocument covers the configuration of this equipment that utilizes either of the following remotecontrol cards; p/n’s 923051-1 (standard) or 943180-1 (supplied upon request). These cardsallow the transceiver to be remotely controlled over 600 ohm dedicated lines using a varietyof keying methods. The Model TSC-4400 Transceiver is a simplex, single channel, fixed frequency transceiveroperating over the frequency range of 118.000 MHz to 138.000 MHz. These units areintended for base station operation in an air traffic environment. These systems can operatefrom AC power or external DC power in local and remote operating modes.1.2 DESCRIPTIONThe TSC-4400 is a fully pre-programmable 50 Watt transceiver. It can be configured for 2 Wireand 4 Wire remote operation with a variety of remote keying methods (with 923051-1standard card). The transceiver consists of a Power Supply Module, Mother Board, a RemoteControl Board and a 50 Watt RF Amplifier Module.To improve the rejection of interfering signals, dual conversion receiver technology has beenincorporated on the Transmitter/Receiver (Module A1) board used in the TSC-4400. Thesecond IF is 455kHz using a ceramic filter, which is immune to high energy ringing. The dualconversion module also has a second local oscillator, second mixer and ceramic filter. The firstlocal oscillator is the original VCO.TABLE 1-1 TSC-4400 CONFIGURATIONSystem Motherboard w/25 pin connector AC Powersupply module RF Amplifier RemoteControl CardsTSC-4400 033588-1 043603-1 Model PA-50 043604-1 P/N 923051-1 orP/N 943180-1 (upon request)
1-21.2.1 Transceiver ModuleThe Single Channel Transceiver is based on Transceiver Model 90-6R/8.33. The transceivermodule is a low power VHF/AM transceiver which can transmit or receive on independent, pre-programmable synthesized frequencies, with 25kHz or 8.33kHz channel spacing in thefrequency range 118.000 MHz to 138.000 MHz. The operating frequency can be easilyprogrammed using a PC via the front panel mounted serial DB-9 connector.1.2.2 Power Supply Module - P/N 043603-1The Power Supply Modules provide the DC supply voltage to the transceiver and linearamplifier, and houses a battery charger which can provide charging and trickle charging toexternal rechargeable batteries. The external DC supply must consist of both 48Vdc and12Vdc external batteries. The power supply will accept an input supply voltage between 110-240VAC and will autorange.1.2.3 RF Amplifier Modules - P/N 043604-1The RF Amplifier (Model PA-50) modules provide 50 Watts of power output. The RF Amplifieris fed by the 7 Watt RF output from the transceiver module. An internally mounted RF Relaybypasses the RF Amplifier when in receive mode. The output of the amplifier can vary from25-50 watts by adjusting the transceiver module RF output between 2-7 watts.1.2.4 Mother Board, P/N 033588-1 Mother Board, p/n 033588-1 is supplied with the two available remote control cards andsupports both a 25 pin “D” and 9 pin Positronics remote connectors on the back of thetransceiver chassis. A RJ11 style connector is also provided which supports only 2-wire audiosignals. The Mother Board provides all interconnection between the three external remotecontrol connectors, RF Amplifier Module, Power Supply, Remote Control Board, andTransceiver. The Remote Control Boards, RF Isolator and all internal fuses are mounted on theMother Board.1.2.5 Remote Control Boards1. Line Interface Board P/N 923051-1Provides remote control transceiver operation on 2 wire or 4 wire 600 ohm lines. This boardcan be configured to key the transmitter using a 2175 Hz* continuous tone (see below),plus/minus DC Voltages, ground keying and internal or external DC (15 mA) current loopkeying. Transmit and Receive audio is user selectable for two wires or four wires. *Crystalsfor tone frequencies other than 2175 Hz may be obtained by special order (ie/2380 Hz).
1-32. Line Interface Board P/N 943180-1 Provides remote control transceiver operation on 2 wire dedicated 600 ohm lines utilizing theEIA multi-tone keying format found in the Land Mobile Industry. A high level 2175 tonefollowed by a 1950 Hz guard tone and then a low level 2175 Hz continuous tone is utilizedto key the transceiver. The 943180-1 board can also be jumper strapped for standardaeronautical 2175 Hz continuous tone operation. DC (15mA) current loop and ground keyingis also supported. However this board does not support 4wire operation.NOTE P/N 923051-1 is the default board supplied in all units. The EIA multi-tone board P/N 943180-1 must be special ordered. To determine which remote card your 92-SChas installed the Configuration label on the side of the rack mount chassis should beconsulted.1.2.6 Crystal Filter Board Assembly P/N 923069-1Additional selectivity during receive operation may be obtained using an optional 25 kHz crystalbandpass filter. An 8.33 kHz bandpass filter is not available. Crystal filters are cut to therequired operating frequency and require 6-8 weeks lead time. This item is interchangeablein the field. Refer to Paragraph 2.2.5 for replacement instructions. If no crystal filter optionis ordered, jumper board assembly P/N 923074-1 is installed.1.3 MODES OF OPERATION1.3.1 Local/Remote OperationNOTELocal operation is not disabled when operating in Remote mode and Remote operation is notdisabled when operating in Local mode. The two operating modes operate in parallel.1. LOCAL OPERATION - In local operation, voice audio, and keying (PTT) functions arerouted from the microphone (not supplied) to the transceiver. Receive audio is routedto the internal loudspeaker and phone jack located on the front panel.2. REMOTE OPERATION - In Remote operation, transmit audio, keying (PTT), and receiveaudio functions are routed over land lines to the 600 ohm remote inputs. Internaljumpers can be set for ±DC, ground, or tone transmitter keying, and to provide a DCsquelch signal and RF Output Power signal depending on the remote control board installed. Receive audio is routed to the internal loudspeaker and is adjustable by thevolume control. Transmit audio is also routed to the internal loudspeaker at aninternally adjustable preset level (see conference audio).
1-41.3.1.1 Conference Audio (Optional)NOTE: This feature is only provided upon special order. The component (R7) discussed below is left unpopulated on standard configuration radios.Conference Audio provides the operator with Tx voice on the transceiver speaker whenthe transmitter is remotely keyed from another location. The audio level of thetransmit audio is internally adjustable from 0.0W to 0.5W of audio output. Theadjustment is performed via rotation of the potentiometer R7 (see Figure 2-5 forlocation), which is accessible from the top of the transceiver after removing the topdust cover of the unit.NOTE: The transmit audio level can be increased by rotating potentiometer R7clockwise and decreased by counterclockwise rotation. If further adjustment ofconference audio is required, the top cover of the transceiver module must be removedto gain access to potentiometer R63, located on the Audio Interface Module, A3 (seeFigure 2-5 for location).1.3.2 AC and DC OperationThe unit can be operated by external 120/240 VAC or external 48 VDC & 12 VDC. The ACpower supply will automatically set for operation on 120 VAC or 240 VAC as required.1. AC OPERATION - During AC operation, the unit can charge and trickle charge externalbatteries via the external connectors mounted on the rear panel of the unit. Refer tosection 3 for remote connector pin details regarding DC operation.2. DC OPERATION - The unit can be operated from an external DC supply which provides48VDC(nominal) and 12VDC(nominal).1.4 TECHNICAL SUMMARYA summary of electrical, operational, mechanical and physical characteristics of the SingleChannel Transceiver are provided in Table 1-2.
1-5TABLE 1-2 TSC-4400 LEADING PARTICULARSPOWER REQUIREMENTS: AC Input Voltage/Current ..................100 to 260 VAC @ 3.5 AmpDC Input Voltage/Current ..................48 VDC Nominal @ 5.0 Amp .................12 VDC Nominal @ 5.0 AmpPOWER OUTPUT:Adjustable ............................................ 25-50 WattsOutput Impedance ..........................................50 OhmsMicrophone Compression Range ........................................ 35 dBBattery Charger Current (48V and 12V, Each) ....................... 2.0 Amps MAXREMOTE CONTROL BOARD, P/N 923051-1 specifications:Remote Audio Input .................... 2 or 4 wire (selectable), balanced 600 S linesRemote Tx Timeout .......................................30 to 300 secondsTone Keying:Impedance ................................ 600 S floating with respect to groundTx Control Tone .......................................... 2175 Hz, standardTx Tone Input Level ...........................................0 to -40 dBmTx Tone Control Response Time ................................<12 millisecondsDC Keying .................................................... ±48 VdcLoop Resistance .............................................. 10 KS MAXGround Keying ........................................... Closure to GroundLoop Resistance ............................................... 4 KS MAXRemote RX:Range ............................. +10 dBm to -15 dBm (Factory set to -10dBm)Impedance ................................ 600 S floating with respect to groundRX/TX Interface Signals:Squelch Signal ................................... Ground, Open circuit for MuteTX RF Output Signal ......................... RF ON=Ground,RF OFF=Open CircuitAGC Signal Output ....................................... Linear 0 to +6 VdcTemperature & Humidity:Operating Temperature Range ................ -25EC(-13EF) to +55EC(+131EF)Storage Temperature Range ................. -55EC(-67EF) to +65EC(+149EF)Relative Humidity (Non-Condensing) .................................95%Dimensions & Weight:Width .........................................483 mm (19.0 in) MAXHeight ......................................... 89 mm (3.5 in) MAXDepth ........................................432 mm (17.0 in) MAXWeight .......................................... 11 Kg (20 lbs) MAX
1-6TABLE 1-2 TSC-4400 LEADING PARTICULARS (Continued)TRANSCEIVER MODULE:Dimensions & Weight:Width ......................................... 216 mm (8.5 in) MAXHeight ........................................ 70 mm (2.75 in) MAXDepth .......................................260 mm (10.25 in) MAXWeight .......................................1.8 Kg (3 lb 15 oz) MAXTRANSMITTER:Power Output ................................... Adjustable 2-7 WattsAudio Input .....................................0.05 Vrms to 2.0 VrmsSpeech Processor Dynamic Range ................................. 35 dBModulation ..............................................95% MAXAudio Distortion @ 90% mod (Low Power) .........................7% MAXAudio Distortion @ 90% mod (with Linear Amplifier at High Power) .......10% MAXAudio Frequency Response ....................300 Hz to 2,500 Hz, +1, -3 dBSpurious Emissions ................................. 60 dB below carrierHum and Noise .............................45 dB below modulated carrierRECEIVER:RF Input Impedance ................................50S, VSWR 2:1 MAXSensitivity (12 dB SINAD) @ 1 kHz 30% Mod ...................... 1.5 µvoltsSelectivity, 25 kHz Channel Spacing:Bandwidth at 6 dB Points ....................... Greater Than 15 kHzBandwidth at 60 dB Points .........................Less Than 22 kHzSelectivity, 8.33 kHz Channel Spacing:Bandwidth at 6 dB Points ....................... Greater Than 10 kHzBandwidth at 60 dB Points .........................Less Than 15 kHzAdjacent Channel Selectivity (25kHz and 8.33kHz) ........... Greater Than 80 dBSpurious Response Attenuation ..........................Greater than 90 dBFrequency Stability (-40EC to +55EC) ..................... ±1,000 Hz MAXRF AGC (5 µvolts to 1 volt) ............... Audio Level change of less than 3 dBIntermodulation:Ultimate Sensitivity ...................................... 70 dB30 µvolts ............................................. 45 dB300 µvolts ............................................ 30 dBUnwanted Radiation .......................... Less than 80 µvolts into 50 SHum & Noise @ 1mV RF 30% MOD ............................... 40 dBLoudspeaker Output .................................. 3 W MAXPhone Output ................................ 100 mW into 600 SAudio Distortion 1mV RF Input, 30% MOD ...................3% MAXAudio Distortion 1mV RF Input, 90% MOD .........................5% MAXAudio Output Limiting .................... Less than 1 dB @30 to 100% MODAudio Frequency Response 300 Hz-2500 Hz ....................... +1 -3 dBAudio Acquisition Time .............................. Less than 50 msecsAudio Squelch Characteristics:Squelch Type ........................... Noise and Carrier OperatedCarrier Operated Squelch ......................... Adjustable 1 to 10 µvolts
2-1 SECTION 2PREPARATION FOR USE AND STORAGE2.1 INTRODUCTIONThis section provides the information required for custom configuration and storage of theSingle Channel Transceiver. Custom system configuration includes customizing remote controlboard functions, and Transmit/Receive frequency selection.CAUTION: Antenna must be connected to transceiver before transmitting or permanentdamage to the output stage may occur.2.2 DISASSEMBLY/ASSEMBLY (Refer to Figure 2-1)2.2.1 Remove/Replace Top Dust Cover AssemblyREMOVAL(1) Remove and retain twelve screws securing top dust cover to the 19" rack chassis.(2) Please note the location of the three longer screws which travel through the heatsinkshims rivetted to the inside of the top cover. (3) Lift cover clear of chassis to expose internal view of transceiver as shown in Figure 2-1.REPLACEMENT(1) Position top cover on chassis.(2) Position one screw in each corner of the top cover mounting holes. Place the threelonger screws into their correct holes located over the internal transceiver module.(3) Secure cover to chassis with remaining screws.2.2.2 Remove/Replace Transceiver ModuleREMOVAL(1) Remove dust cover as described in paragraph 2.2.1.(2) Disconnect RF and DC connectors from rear of transceiver module.(3) Remove and retain the screws securing the top cover of the internal transceivermodule.(4) Remove and retain two screws and two washers securing flat cable to the side of thetransceiver module and disconnect the flat cable. Disconnect the flat cable running outof the transceiver module at the connector on the external memory set board. (5) Remove and Retain four countersunk screws securing transceiver module to frontpanel.
2-2 Figure 2-1Single Channel Transceiver - Internal View
2-3 (6) Move the transceiver module slightly back from the front panel and disconnect theflat cable connecting the front panel assembly to the transceiver module, audiointerface board A3. The connector is located on the A3 board.(7) Lift transceiver module clear of chassis.REPLACEMENT(1) Position the transceiver module into the chassis. While holding the transceivermodule slightly back from the front panel, re-connect the flat cable from the frontpanel to the A3 board in the transceiver module.(2) Position and secure transceiver module to front panel with four countersunkscrews.(3) Re-connect flat cable to transceiver module. Secure flat cable to the side oftransceiver module with two screws and two washers. Connect flat cable runningout of the transceiver module to the external memory set board. Connect DC andRF connectors to rear of transceiver module.(4) Replace and secure the top cover of the transceiver module with the screwsremoved in step (3) of the REMOVAL instructions. Replace top dust cover asdescribed in paragraph 2.2.1.2.2.3 Remove Replace External Single Channel Memory Set Module A5A1REMOVAL(1) Remove dust cover as described in paragraph 2.2.1, remove top cover oftransceiver module.(2) Disconnect the two crystal filter co-axial cable leads for jumper J2/P3 on the Rx/Tx module A1, located in the transceiver module.(3) Remove and retain four screws securing Memory Set Board, Module A5A1 "piggyback" to the standoffs on the power supply cover. (See Figure 2-1 for location).REPLACEMENT(1) Secure the Memory Set Module to the stand-offs located on the power supply coverby the four screws. Re-connect coaxial leads for RF crystal filter.2.2.4 Remove/Replace Control BoardREMOVAL(1) Remove dust cover as described in paragraph 2.2.1.CAUTION Care must be taken when removing or replacing Control Board to avoid damage to Motherboard Connector Pins.(2) Remove and retain four screws securing Control Board "piggy back" to the Mother Board standoffs. Remove Control Board from Mother Board.
2-4 Figure 2-2 Programming Interface Board with Crystal Filter Option
2-5 REPLACEMENT(1) Align the two female connectors on the control board with the male connectorson the Mother Board using the four mounting holes and standoffs as a guide. Secure control board to the Mother Board standoffs with four screws and washers. (2) Replace dust cover as described in paragraph 2.2.1.2.2.5 Remove/Replace Crystal Filter Board, p/n 923069 or Jumper Board, p/n 923074REMOVAL(1) Remove dust cover of unit as described in Paragraph 2.2.1.(3) Remove and retain the four screws securing the crystal filter board, p/n 923069-1(or jumper Board, p/n 923074) to the standoffs on the external frequency setmodule A5A1. Pull the crystal filter board assembly straight up to avoid damagingthe connector pins. REPLACEMENT(1) Align the pins on the bottom of the crystal filter board with their sockets on thememory set board. Push the crystal filter board straight down until it rests on thememory set board standoffs and secure with the four mounting screws. (2) Connect Module A5A1 co-axial jumper leads to jumper J2/P3 on Rx/Tx Module A1,if not already connected. Either a crystal filter board, p/n 923074 or a jumperboard, p/n 923074 must be installed and the A5A1 co-axial jumper leads connectedto J2/P3 on the Rx/Tx Module A1, for the receiver to work. NOTE: Make certain that the memory set board, module A5A1 is programmed to the same operating frequency as the crystal filter board assembly. If no crystal filter board assembly (option) is installed, jumper board assembly P/N 923074-1 must be installed. 2.3 CHANNEL FREQUENCY PROGRAMMING2.3.1 IntroductionTransceiver Model TSC-4400, as shipped from the factory, is preprogrammed with a testfrequency. Before programming a new frequency, perform an operational check. If there isany deficiency or equipment malfunction, the transceiver is to be returned to themanufacturer, Technisonic Industries Limited, under warranty.2.3.2 Frequency RangeThe operating frequency may be programmed over the frequency range 118.000 MHz to 138.000 MHz with 8.33kHz or 25kHz channel spacing.2.3.3 Frequency Programming RequirementsA personal computer is required to reprogram a new frequency into the transceiver channelmemory. Refer to document 04RE332 (Section 3, Addendum A) for detailed instructions onTDP-90 software installation and operation.
2-6 A standard 9 pin serial cable must be temporarily connected between the front panel DB-9connector on the transceiver and the computer serial port.The transceiver is capable of 25 kHz spacing (wide band) and 8.33 kHz spacing (narrowband) channels. The frequency entered will determine whether the channel will be wide ornarrow mode, based on the Combined 8.33 kHz/25 kHz ICAO Frequency-Channel PairingPlan. For example if you program 118.000 into a memory, the transceiver will operate on118.000 MHz in wide band mode. If you program 118.005 into a memory, the transceiverwill operate on 118.000 MHz in narrow band mode. For the most part, this will betransparent to the user since a frequency will be issued in the ICAO format and the radiowill select wide or narrow mode. Refer to the chart below.TABLE 2-1 COMBINED 8.33/25 kHz ICAO FREQUENCY CHANNEL PAIRING PLANFrequency Entered (MHz) Actual Operating Frequency Channel Spacing (kHz)118.000 118.0000 25118.005 118.0000 8.33118.010 118.0083 8.33118.015 118.0166 8.33118.025 118.0250 25118.030 118.0250 8.33118.035 118.0333 8.33118.040 118.0416 8.33118.050 118.0500 25118.055 118.0500 8.33118.060 118.0583 8.33118.065 118.0666 8.33118.075 118.0750 25118.080 118.0750 8.33118.085 118.0833 8.33118.090 118.0916 8.33118.100 118.1000 25118.105 118.1000 8.33etc etc etc
2-7 2.3.4 Programming a FrequencyHaving ascertained the desired operating frequency, continue as follows:(1) Run the TDP-90 program on the computer.(2) Click on the Data pull-down list and select the serial port to which the transceiver isconnected.(3) Set the program for 1 channel.(4) Turn on power to the transceiver.(5) Click on the Up icon to retrieve the frequencies from the radio. You will see activityin the Terminal window as data is being transferred. (6) Edit the frequencies as desired.(7) Click on the Dn icon to copy the frequency to the transceiver. You will see activityin the Terminal window as data is being transferred. (8) Click on the diskette icon to save the file.(9) Click on the printer icon to print a hard-copy of the frequency.(10) Turn off power to the transceiver.
2-8 2.4 REMOTE OPERATION SETUPThe Procedures listed below enable the user to custom configure the unit for externalremote control hardware. Refer to Table 2-3 for connector pin details on Remote Control DConnector located at rear of Single Channel Transceiver. Position Jumpers on Control boardas indicated in Table 2-4 or Table 2-5 as required. Refer to Figure 2-3 and Figure 2-4 forboard locations. Verify Remote Control operation in accordance with manufacturersinstructions.TWO WIRE SETUP - In two wire operation, a single balanced 600 ohm pair is provided for transmit and receive audio. The transmitter can be keyed on the same pair or externally.FOUR WIRE SETUP - In four wire operation, separate balanced 600 ohm pairs are providedfor transmit and receive audio. The transmitter can be keyed on the Tx audio pair orexternally.DC KEYING - In ± DC keying, a positive voltage between +10 Vdc and +48 Vdc or negative voltage between -10 Vdc and -48 Vdc will key the transmitter. A DC voltagebetween -5 Vdc and +5 Vdc will not key the transmitter.TONE KEYING - In Tone keying a tone of 2175 Hz or 2380 Hz (Optional) can be used tokey the transmitter. Tone sensitivity is adjustable from -40 dBm to 0 dBm.GROUND KEYING - In Ground Keying the transmitter is keyed by shorting the control point (landline or External Keying) to chassis groundCURRENT LOOP KEYING - In Current Loop keying, an internal or external current source(15 mA) is used to key the transmitterEIA TONE KEYING - The EIA multi-tone keying format is found in the Land Mobile Industry.A high level 2175 Hz tone followed by a 1950 Hz guard tone then a low level 2175 Hz continuous tone is utilized to key the transceiver.TABLE 2-2 REMOTE CONTROL CONNECTOR FUNCTIONS9 PINNO 25 PINNO Connector Pin FunctionsA,BC,DN/AKJN/AE(-),F(+)N/AN/A9,2110,228131,2,14,152523(-),11(+)203,4,5,6,7,16,17,18, 19 4 Wire Tx Audio Line or 2 Wire Rx/Tx Audio Line (600 S) 4 Wire Rx Audio Line (600 S) AGC Single Line Keying (PTT) Ground Squelch Carrier Control RF Indicator Not Connected, allocated for future functionsNOTE: A modular RJ-11 Jack is also provided on the rear of the 19" rack chassis for quickconnection to the 2 wire, Tx/Rx Audio. The red and green wire connections (centre pins) on theRJ-11 are connected parallel to pins 9 and 21 on the 25 pin connector. This RJ-11 jack CANNOTbe used if the remote control card is set to 4-wire operation as it does not have the necessaryconnections.
2-9 2.4.1 Two/Four Wire Remote Control Board P/N 923051-1 Provides remote control base station operation on 2 wire or 4 wire, 600 ohm lines. Thisboard can be configured to key the transmitter using a 2175 Hz tone (2380 Hz uponrequest), plus/minus DC Voltages, ground keying and internal or external current loopkeying. Transmit and Receive audio is user selectable for two wires or four wires. Crystalsfor tone frequencies other than 2175 Hz or 2380 Hz may be obtained by special order.See Figure 2-3 for location of jumpers referred to in the following table. Pins are numbers increase as you go from top to bottom or left to right on the connector.TABLE 2-3 REMOTE CONTROL BOARD P/N 923051-1 SETTINGSCONTROL FUNCTIONJ1 Jumper Pin 1 and Pin 2 for DC Current Loop KeyingJumper Pin 2 and Pin 3 for ± DC Keying or Ground Keying. Note: SW2 must be in position 2 if Pin 2 and Pin 3 are jumpered.J2J3J7J6SW1SW2Y1,Y2R7R22R25R44R10Jumper Pin 1 and Pin 2 for Ground Keying (Land Line).Jumper Pin 1 and Pin 4 for ± DC Keying (Land Line).Jumper Pin 2 and Pin 3 for Ground Keying (Single Key Line).Jumper Pin 3 and Pin 6 for ± DC Keying (Single Key Line).Jumper Pin 2 and Pin 5 for No Function.Jumper Pin 1 and Pin 2 for ± DC or Ground Keying.Jumper Pin 4 and Pin 5 for Tone Keying. Note: Both Options may be selected.Jumper Pin 2 and Pin 3 for No Function.Jumper Pin 5 and Pin 6 for No Function.Jumper Pin 1 and Pin 2 to enable Timeout Timer.Jumper Pin 2 and Pin 3 to disable Timeout Timer.Jumper Pin 1 and Pin 2 to for Internal Current Loop Keying.Jumper Pin 2 and Pin 3 to for External Current Loop Keying.Position 1 Selects 2 Wire Operation.Position 2 Selects 4 Wire Operation.Position 1 Selects Normal (Land Line Keying).Position 2 Selects Local (Single Line Keying).Determines Keying Tone Frequency.Sets Tx Audio IN Level (Range -18 dBm to +10 dBm).Sets Key Tone Level (Range -40 dBm to 0 dBm).Sets Rx Audio OUT Level (Range -15 dBm to +10 dBm).Sets Timeout Timer (Range 30 to 300 Seconds).Sets Receive Audio Output Balance.
2-10 2.4.2 Two Wire Line Interface Board P/N 943180-1 Provides remote control Base Station operation on 2 wire 600 ohm lines. Two wire Line Interface board with EIA multi-tone, standard 2175Hz continuous tone, DC keying ofground keying over audio lines. The multi-tone keying format consists of a high level 2175tone followed by a 1950 Hz guard tone and then a low level 2175 Hz continuous tone isutilized to key the transceiver. This board will also support 15mA current loop or groundkeying. Refer to Figure 2-4 for jumper locations to set functions and line level adjustmentsfor this board. Summary of jumper settings follow. Pins are numbers increase as you gofrom top to bottom or left to right on the connector.Set J1 for ST (standard 2175Hz continuous) Tone keying or for EIA (multi-tone keyingformat).Set J2 for Tone keying function ON (left jumper position) or OFF (right jumper position).Set J3 for Time out timer OFF (left jumper position) or ON (right jumper position).See Figure 2-4 for location of jumpers and left/right orientation.TABLE 2-4 REMOTE CONTROL BOARD P/N 943180-1 SETTINGSCONTROL FUNCTIONJ1 Jumper Pin 1 and Pin 2 for ST (standard 2175 Hz continuous) tone KeyingJumper Pin 2 and Pin 3 for EIA multi-tone Keying.J2J3R6R24R26R41R59R64Jumper Pin 1 and Pin 2 for Tone Keying.Jumper Pin 4 and Pin 5 for Current Loop (15mA DC) or Ground Keying. NOTE: Both options may be selectedJumper Pin 2 and Pin 3 to disable Tone Keying.Jumper Pin 5 and Pin 6 to disable Current Loop and Ground Keying.Jumper Pin 1 and Pin 2 to enable Timeout Timer.Jumper Pin 2 and Pin 3 to disable Timeout Timer.Tx audio level AdjustmentKeying Tone Attenuator1950 Tone level Adjustment2175 Tone Level AdjustmentSets Rx Audio Level Adjustment (Range -15 dBm to +10 dBm).Sets Timeout Timer (Range 30 to 300 Seconds)
2-11 Control Configuration for 2/4 Wire (+/-)DC/Ground/Tone/(Current Loop) Keying Control Board.Assembly #: 923051R7: Tx Audio SW2: Selects either Local(-25 dBm sensitivity; or Land Line Currentincreases clockwise). Loop Keying.R10: 2 Wire Rx Balance @ 600OJ1: Selects DC or Current(1mV RF @ 1KHz, 30% Mod.) Loop Keying operation.R10 adjusted for minimum J2: Selects either Land Lineamplitude at C6/R4 junction. (L/L) or Single Line (S/L)R22: Keying Tone and +/- DC or Ground(-30 dBm sensitivity; keying operation.decreases clockwise). J3: Selects Tone and/or +/- DCR25: Rx Audio Keying enable or disable.(-10 dBm output level; J6: Selects between Internalincreases clockwise). or External Current loopR44: Time Out Timer keying (ICL/ECL).(15 to 300 sec.; J7: Keying timer90 sec. Nominal; Enable/Disable.increases clockwise). J4: Input Connector.SW1: Selects either 2 Wire J5: Output Connector.or 4 Wire operation.NOTE: Bold Italics indicate Factory default configurations.Figure 2-3 Line Interface/Remote Control Board P/N 923051-1
2-12 Control Configuration for Multi-Tone Control Board.Assembly #: 943180 R6: Tx audio level adjustment (-25 dBm). J1: Standard or EIAR24: Keying Tone Attenuator. Keying tone protocol.R26: 1950 Hz tone level adjustment J2: Selects Tone and/or Current Loop/R41: 2175 Hz tone level adjustment Ground Keying enable or disableR59: Rx Audio level adjustment. J3: Selects Keying timer Enable/Disable(-10 dBm)J4: Input Connector R64: Time out timer J5: Output Connector(90 sec. default)NOTE: Bold Italics indicate Factory default configurations.Figure 2-4Line Interface/Remote Control Board P/N 943180-1
2-13 2.5 OPTIONAL LOUDSPEAKER, HEADPHONE INSTALLATIONProvision is made for connection of an external loudspeaker or headphone to the SPEAKER/PHONE jack of the transceiver, as shown in Figure 3-1.2.5.1 External LoudspeakerWhen an external loudspeaker is to be installed, an 8-ohm nominal impedance loudspeakershould be used. The loudspeaker cable should be terminated by a 1/4 in., 3-pole telephone plug(male), with the loudspeaker connected between tip and sleeve (ground). Insert the externalloudspeaker connector into the SPEAKER/PHONE jack located on the front panel of thetransceiver. When the external loudspeaker is connected to the transceiver SPEAKER/PHONEjack, the internal loudspeaker is automatically disconnected.2.5.2 HeadsetHeadset impedance should be 150 to 600 ohms. The headset cable must terminate in a 1/4in. 3-pole telephone plug (male), to mate with the SPEAKER/PHONE jack located on the frontpanel of the transceiver. The internal loudspeaker is automatically disconnected. Connect theheadset as indicated below for receiver audio with or without transmit audio.(1) HEADSET WITHOUT TRANSMIT AUDIO - When receiver audio only without transmitaudio is required, the headset should be connected between the tip and sleeve (ground)of the telephone plug.(2) HEADSET WITH TRANSMIT AUDIO - When receiver audio with transmit audio is required, the headset should be connected between the ring and sleeve(ground).2.6 TRANSCEIVER ADJUSTMENTS AND SETTINGSThe locations at which certain transceiver settings and adjustments can be performed areshown in Figure 2-5. The top dust cover of the transceiver must be removed as described inparagraph 2.2.1 to access the AGC, Squelch and Modulation settings. The plastic plugs mustbe removed prior to adjustment of the remaining settings which are accessed from the bottomof the transceiver chassis. If alignment procedures for these settings are required pleaseconsult the manufacturer or the appropriate service manual.2.7 OPERATIONAL CHECKPerform an operational check of the transceiver after all adjustments. Ensure that thetransceiver operates in both the transmit and receive modes of operation, using the OperatingInstructions given in Section 3 of this document and the appropriate specified operatingprocedures for use with the Remote Control Unit.2.8 STORAGETo store for an extended period, store unit in a dry place, in the original shipping container.
2-14 Figure 2-5Transceiver Adjustments and Settings
3-1SECTION 3OPERATING INSTRUCTIONS3.1 INTRODUCTIONThis section includes a functional description of each switch, control, indicator and connectorlocated on the front and rear panels of the portable transceiver, including the PRESS-TO-TALKswitch located on the microphone. Operating instructions for transmit/receive and the specialfunctions are also included.3.2 INSTALLATIONThe TSC-4400 Transceiver is designed to be mounted in a 19 inch rack. An AC Line cord P/N927002-1 is supplied for connection to AC Power. A 9 Pin connector (mates with PositronicGM9MSCG000VL or equivalent) and a 25 Pin Connector (mates with Amphenol 17D-B-25Sor equivalent) are provided for connection with external DC and 2 Wire or 4 Wire 600 ohmdedicated lines. A 50 ohm "N" Type connector is provided for connection to an externalantenna. Refer to Section 2 for frequency selection and remote control setup details.(1) Mount Transceiver in 19 inch rack with 4 screws.(2) Install Microphone in Microphone (PTT) connector if required. (3) Ensure that Transceiver POWER ON/OFF switch is set to OFF.(4) Install AC line cord in AC chassis connector on rear panel.(5) Install Remote Control connector to 9 Pin or 25 Pin connector as required. (Refer toFigure 3-1 for connector pin outs.)(6) Connect antenna connector to rear panel chassis N Type connector.3.3 OPERATOR'S SWITCHES, CONTROLS AND INDICATORSA view of the front and rear panel is given in Figure 3-1. A functional description of each ofthe operator's switches, controls and indicators, and the microphone PRESS-TO-TALK switch,is given in Table 3-1, Operator's Switches, Controls and Indicators.
3-2Figure 3-1 Single Channel Transceiver Controls and Indicators
3-3TABLE 3-1 OPERATOR'S SWITCHES, CONTROLS AND INDICATORSItemNo. SWITCHESCONTROLS &INDICATORS FUNCTIONAL DESCRIPTION1POWER ON/OFFSWITCH A toggle switch applies the AC power to the power supply and theDC voltage to the transceiver. The transceiver is switched to ON inthe toggle UP position the transceiver is switched OFF in the toggleDOWN position.2POWER ON LEDINDICATOR A GREEN LED Indicates when the POWER ON/OFF switch is set toON and voltage is applied to the transceiver.3SQUELCHCONTROL A linear potentiometer determines the squelch threshold level. Whenthe SQUELCH CONTROL is rotated in the counter-clockwisedirection, the SQUELCH GREEN LED indicates that the squelch isconnecting demodulated audio to the VOLUME control.4SQUELCHINDICATOR A GREEN LED indicates the squelch circuit is connecting demodulatedaudio signal to the VOLUME control.5Tx ON AMBER LEDINDICATORAn AMBER LED indicates when the transceiver is keyed by themicrophone PRESS-TO-TALK (PTT) switch or remote land line, andthe transceiver is operated in the Tx mode. The Tx ON AMBER LEDswitches OFF, when the transceiver is operated in the receive mode.6VOLUMECONTROL A logarithmic potentiometer determines the audio level applied to theinternal speaker when the transceiver is operated in the receivemode. When the SPEAKER/PHONE connector is in use the internalloudspeaker is disconnected and the VOLUME CONTROL sets theaudio level applied to the external speaker or headphone.7MIC/PTTCONNECTOR A standard 0.2 inch 3-pole jack is provided to connect a microphonewith PTT to the transceiver front panel.8TX LABEL Indicates the frequency programmed for transmit.
3-4 TABLE 3-1 OPERATOR'S SWITCHES, CONTROLS AND INDICATORS (Continued)ItemNo. SWITCHESCONTROLS &INDICATORS FUNCTIONAL DESCRIPTION9RX LABEL Indicates the frequency programmed for receive.10 LOUDSPEAKER An 8-ohm internal speaker reproduces the receiver audio output.The audio line is disconnected from the internal loudspeaker whenthe transceiver is operated in Tx mode or when theSPEAKER/PHONE connector is in use.11 SPEAKER/PHONECONNECTORA 3-pole connector provides interconnection to either an externalloudspeaker or headphone. When in use, the internal speaker isdisconnected and the VOLUME control sets the audio level appliedto the external speaker or headphone.12 DC POWERCONNECTOR A 3 Pin connector for use with DC Power Supply (12VDC and 50VDC nominal)13 AC FUSE A 5.0 Amp Slo-Blo fuse protects the Base Station power supplyfrom power supply internal short circuit or transceiver short circuit.14 * "N" TYPE RF CONNECTOR A 50 ohm coaxial connector provides connection to externalantenna.15 *AC POWER CONNECTOR 3 Prong AC Connector for use with AC Power Cord P/N 927002-1.16 *9 PIN REMOTE CONTROL CONNECTOR9 Pin "D" type connector provides connections required for remoteoperation. Refer to Table 2-3 for connector details.17 *25 PIN REMOTE CONTROL CONNECTOR25 Pin "D" type connector provides connections required for remoteoperation. Refer to Table 2-3 for connector details.18 *RJ-11 REMOTE CONNECTOR RJ-11 type connector provides parallel connection to the 2-WireTx/Rx audio from remote/line interface board. This connectorsupports 2 wire operation only.* Denotes items located on rear panel.
3-53.4 OPERATING INSTRUCTIONSNOTERefer to appropriate Operating Instructions for usewith Remote Control Unit.NOTEThe following operating procedures are intendedspecifically for Local Operation.(1) Ensure that the microphone connector is connected to the MIC/PTT connector ofthe transceiver.(2) Set the SQUELCH control in the fully counter-clockwise (CCW) position.(3) Set the VOLUME control in the 12 o'clock centre position.(4) Set the POWER ON/OFF switch to "ON".(5) Verify that the POWER ON green LED is ON.(6) Proceed to operate in the transmit mode, paragraph 3.4.1 or operate in the receive mode, paragraph 3.4.2 as required.3.4.1 Transmitter Operation (Local Mode)To operate the transceiver in the transmit mode, proceed as follows:(1) Set RF POWER switch (if applicable) to desired operating level.(2) Hold the microphone in one hand, with the upper edge of the microphone as closeas possible to the upper lip.NOTEThis technique activates the noise cancelling featureof the microphone. The microphone is most effectivewhen sound is ½ inch (12.7 mm) or more away fromthe microphone.(3) Press and hold the PRESS-TO-TALK switch of the microphone during transmission.(4) Ensure that the Tx ON amber LED is ON.(5) Speak slowly and distinctly into the microphone using specified operatingprocedures during transmission.(6) When message is ended, release the PRESS-TO-TALK switch of the microphone.(7) The transceiver is now operating in the receive mode.(8) Verify that the Tx ON amber LED is OFF.
3-63.4.2 Receiver Operation (Local Mode)To operate the transceiver in the receive mode, proceed as follows:(1) Ensure that the PRESS-TO-TALK switch on the microphone is NOT depressed, and verify that the Tx ON amber LED is OFF.(2) Verify that the correct operating frequency is indicated on the front panel.(3) Adjust the SQUELCH control to suit local reception conditions. When the SQUELCH control is rotated in the counter-clockwise direction, the SQUELCHindicator green LED will switch to ON, indicating that the squelch circuit isconnecting the demodulated audio output to the VOLUME control.Further adjustment of the SQUELCH control determines the squelch setting.IMPORTANT NOTEThe dual conversion receiver’s squelch knob must be rotated significantly moreclockwise (4 o’clock position) to obtain the same squelch setting (3uV) as a singleconversion receiver’s squelch knob set to the 12 o’clock (straight up) position.If the receiver’s squelch knob is set to the 12 o’clock position, signals with a levelgreater than 0.5uV will open the squelch. At most airports this will not be anadequate level of squelch.Recommended procedure:The squelch taper on a dual conversion receiver looks as follows:Squelch knob position Squelch setting 12 o’clock 0.5uV3 o’clock 1.2uV3:30 position 2.5uV4 o’clock 3uVFully clockwise 9uV It is recommended that the squelch be set to at least 2.5uV (3:30 knob position) atbusy airport locations. If ACARS signals are present on adjacent or nearby channelsthe squelch level should be at least 3uV (4 o’clock) to prevent ACARS bleedthrough. (4) The VOLUME control can then be adjusted in a clockwise direction to increase theaudio level, or in a counter-clockwise direction to decrease the audio level whichcan be heard on the internal loudspeaker.NOTEWhen an external loudspeaker or headset isconnected to the SPEAKER/PHONE jack of thetransceiver, the internal loudspeaker is automaticallydisconnected. The VOLUME control will now controlthe audio level applied to the external loudspeaker orheadset, as applicable.
3.4.3 Switching OFFTo switch off the transceiver:(1) Set the POWER ON/OFF on transceiver to switch to OFF.(2) Verify that all indicator LED's on the front panel are OFF.NOTEWhen the transceiver is switched OFF there is nocurrent drain from external DC.3.4.4 EXTERNAL DC OPERATION(1) Set AC ON/OFF switch to OFF.(2) Refer to Figure 3-1 for pin locations to hook up external DC Power.3-7
Section 3Addendum ATil Document No.04RE332
This document contains designs and other information which are the property of TechnisonicIndustries Ltd. Except for rights expressly granted by contract to the Canadian Government, or tothe United States Government, this document may not in whole or in part, be duplicated ordisclosed or used for manufacture of the part disclosed herein, without the prior permission ofTechnisonic Industries Ltd.TiL TDP-90 Data Programming Softwarefor the TSC-4400TransceiverInstallation and Operating InstructionsTiL Document No.04RE332Rev. n/c March 2004 Technisonic Industries Limited 240 Traders Blvd. E., Mississauga, Ontario L4Z 1W7 Tel:(905)890-2113 Fax:(905)890-5338 www.til.ca
TABLE OF CONTENTSParagraph Title PageSECTION 1 GENERAL DESCRIPTION1.1 Introduction ...............................................1-11.2 Description ...............................................1-11.3 Minimum System Requirements .................................1-1SECTION 2 INSTALLATION INSTRUCTIONS2.1 Software Installation .........................................2-12.1.1 - Windows 95 .........................................2-32.1.2 - Windows 98 / Windows 2000 .............................2-42.1.3 - Windows NT 4.0 ......................................2-42.2 Hardware Installation .........................................2-5SECTION 3 OPERATING INSTRUCTIONS3.1 General ..................................................3-13.2 Getting Started .............................................3-13.3 Pull Down Menus ...........................................3-23.3.1 - File Menu ...........................................3-23.3.2 - Data Transfer Menu ....................................3-33.3.3 - Help Menu ..........................................3-43.3.4 - Channel Selection ......................................3-53.4 Sample Upload and Download ..................................3-63.5 RS-232 Serial Technical Data ...................................3-7
LIST OF ILLUSTRATIONSFigure No. Title Page2.1.1 Setup Extraction Dialog .......................................2-12.1.2 Welcome Dialog ............................................2-12.1.3 License Agreement ..........................................2-22.1.4 Program Installation Dialog .....................................2-22.2.1 Programming Connections for Mobile transceivers .....................2-62.2.2 Programming Connections for Base Station transceivers ................2-72.2.3 Programming Connections for Rack Mount transceivers .................2-73.3.1 File Menu Pulldown ..........................................3-23.3.2 Data Menu Pulldown .........................................3-33.3.3 Help Menu Pulldown .........................................3-43.3.4.1 Single Channel Selection ......................................3-43.3.4.2 Six Channel Selection ........................................3-5
Copyright and Trademark acknowledgement- Microsoft, Windows 95, Windows 98, Windows NT, Windows 2000, DCOM, and Internet Explorer are registeredtrademarks of Microsoft Corporation.- DPL is a registered trademark of Motorola Inc.SAdobe, Adobe Acrobat, and Adobe Acrobat Reader are registered trademark of Adobe Systems Inc.
1-1SECTION 1GENERAL DESCRIPTION1.1 INTRODUCTIONThis publication provides operating and installation information on the TiL TDP-90 Programming Software for 8.33 kHz AM series transceivers. The TDP software allows astandard PC to retrieve data from a connected 8.33kHz AM series transceiver, for editing,storing, and sharing with other 8.33 kHz AM series transceivers. With the TDP software,you can create, save and print archives of your 8.33 kHz AM series transceiver channelsettings.1.2 DESCRIPTIONThe TiL TDP-90 software is a 32 bit Windows application that will work under Windows95, Windows 98 and Windows NT 4.0. There are no known issues preventing the TDP-90from working under Windows 2000. Please see section 2 for details on your particularinstallation.1.3 MINIMUM SYSTEM REQUIREMENTSWindows 95•Intel 486 or compatible based PC•Windows 95 with the latest Service Releases/Packs installed (Installation of Microsoft Internet Explorer 5.0 or any Microsoft application more recent than mid 1998, will have automatically updated the required system files.)•Mouse•5 MB free Hard-Disk space•One available properly configured RS-232 serial (COM) portor Windows 98 / Windows 2000•Intel or compatible Pentium class PC •Windows 98 or Windows 2000 with the latest Service Releases/Packs installed•Mouse•5 MB free Hard-Disk space•One available properly configured RS-232 serial (COM) portor Windows NT 4.0•Intel or compatible Pentium class PC•Windows NT 4.0 with at least Service Pack 4 installed(Installation of Microsoft Internet Explorer 5.0 or any Microsoft application more recent than mid 1998, will have automatically updated the required system files.)•Mouse•5 MB free Hard-Disk space•One available properly configured RS-232 serial (COM) port
2-1SECTION 2INSTALLATION INSTRUCTIONS2.1 SOFTWARE INSTALLATIONBefore the TDP software can be installed, all of the minimum computer systemrequirements outlined in the previous section must be met, otherwise difficulty may beencountered during installation or operation the software.The installation procedures outlined in this document assume some basic workingknowledge of at least one of Microsoft's Windows 95/98/NT/2000 operating systems.NOTE: At any point during installation, if any Dialog Boxes pop up exclaiming that newersystem files are about to be overwritten by older files, click on NO to skip overwritingnewer files.Figure 2.1.1 - Setup Extraction DialogFigure 2.1.2 - Welcome DialogThis is a standard Welcome dialog box. To continue installation click on Next>. In any oneof the dialog boxes, program installation can be stopped at any time by clicking the Cancelbutton.
2-2Figure 2.1.3 - License AgreementIn order to Install the TDP-90 Software onto your computer, you must agree to the termsof the license agreement, and confirm so by clicking on OK in the License dialog box.Figure 2.1.4 - Program Installation Dialog
2-32.1.1 Windows 95If your computer does not have Microsoft Internet Explorer 5.0 or any otherMicrosoft application, no later than mid 1998 installed, then it is possible thatcertain essential system files are outdated. If these system files are outdated yoursystem will not meet the minimum requirements for installing and operating a largevariety of new software including the TDP software.If your computer DOES meet the minimum requirements, you may proceed to step 3.1. To update Windows 95, you will need to install an update available on Microsoft'swebsite, called DCOM95 (dcom95.exe). To download DCOM95, just enter thiscurrent (as of the release date of this manual) Internet URL for the file in your‘location bar’ in your Internet Browser.http://download.microsoft.com/msdownload/dcom/95/x86/en/dcom95.exeYour Browser will invoke a SAVE AS dialog box for you to save the file. Keep trackof where you place it, as you will be required to locate it and RUN it. Conveniently,the file will fit on a regular IBM Formatted 3½" 1.44MB floppy disk, for easytransport and distribution.If you have the DCOM95.EXE update file on a floppy disk, copy/place it in atemporary location on your Hard-disk.2. RUN DCOM95 by locating and double-clicking on it in Windows Explorer. AnySystem files on your computer that are OLDER than the ones contained in theDCOM95 update, will be replaced. You will be asked to restart your computer. Doso, and when the computer has finished booting, you will have an updatedOperating System that will meet the requirements of the TDP software.3. To install the TDP software, locate the TDP90_Install.exe file on the CD-ROM usingWindows Explorer. When you have located it, double-click it to start the setupprocess.You will see the first Setup dialog (Figure 2.1.1). Click on the Setup button tocontinue installation. The Setup will unpack the necessary components. After itcompletes, you will see a Welcome dialog box. Click Next> to continue. Before youcan continue, you will have to agree to the terms of the License Agreement byclicking OK (Figure 2.1.3).The setup wizard may or may not ask to reboot the computer, depending on whichcomponents your system required from the installation package. If so, let thecomputer restart and run setup again to complete the installation process. Nofurther reboots will be required.4. After setup finishes unpacking the software, a dialog box will pop up with theoption to continue (by clicking on the Next> button see Figure 2.1.4), exit thesetup, or at this time you may choose an alternate location for the installation. Ifyou have no objections to the default location just click on the Next> button tocontinue the installation.5. The TDP installation will ask what START menu Program Group you want the TDPsoftware shortcut installed. Click FINISH if the default Program Group name isadequate.The Data Programming Software is now installed and ready to use with an 8.33kHz AM series Transceiver.
2-42.1.2 Windows 98 / Windows 2000Windows 98 comes pre installed with Internet Explorer 5.0 embedded into theoperating system. As a result, the operating system as a whole meets therequirements for the installation and operation of the TDP software.1. To install the TDP software, locate the TDP90_Install.exe file on the CD-ROM usingWindows Explorer. When you have located it, double-click it to start the setupprocess.You will see the first Setup dialog (Figure 2.1.1). Click on the Setup button tocontinue installation. The Setup will unpack the necessary components. After itcompletes, you will see a Welcome dialog box. Click Next> to continue. Before youcan continue, you will have to agree to the terms of the License Agreement byclicking OK (Figure 2.1.3).The setup wizard may or may not ask to reboot the computer, depending on whichcomponents your system required from the installation package. If so, let thecomputer restart and run setup again to complete the installation process. Nofurther reboots will be required.2. After setup finishes unpacking the software, a dialog box will pop up with theoption to continue (by clicking on the Next> button see Figure 2.1.4), exit thesetup, or at this time you may choose an alternate location for the installation. Ifyou have no objections to the default location just click on the Next> button tocontinue the installation.3. The TDP installation will ask what START menu Program Group you want the TDPsoftware shortcut installed. Click FINISH if the default Program Group name isadequate.The Data Programming Software is now installed and ready to use with an 8.33kHz AM series Transceiver.2.1.3 Windows NT 4.0For a Windows NT 4.0 installation, a minimum of Service Pack 4 must be installed.If you do not have at least Service Pack 4, contact Microsoft for the most currentService Pack.1. To install the TDP software, locate the TDP90_Install.exe file on the CD-ROM usingWindows Explorer. When you have located it, double-click it to start the setupprocess.You will see the first Setup dialog (Figure 2.1.1). Click on the Setup button tocontinue installation. The Setup will unpack the necessary components. After itcompletes, you will see a Welcome dialog box. Click Next> to continue. Before youcan continue, you will have to agree to the terms of the License Agreement byclicking OK (Figure 2.1.3).The setup wizard may or may not ask to reboot the computer, depending on whichcomponents your system required from the installation package. If so, let thecomputer restart and run setup again to complete the installation process. Nofurther reboots will be required.
2-52. After setup finishes unpacking the software, a dialog box will pop up with theoption to continue (by clicking on the Next> button see Figure 2.1.4), exit thesetup, or at this time you may choose an alternate location for the installation. Ifyou have no objections to the default location just click on the Next> button tocontinue the installation.3. The TDP installation will ask what START menu Program Group you want the TDPsoftware shortcut installed. Click FINISH if the default Program Group name isadequate.The Data Programming Software is now installed and ready to use with an 8.33kHz AM series Transceiver.
2-62.2 HARDWARE INSTALLATIONRack Mount Transceiver: Plug the female end of a 9 pin serial cable into the 9 pin D connector on the front panel ofthe unit. Connect the other end of the serial cable to an available Serial (COM) Port on yourPC. Plug the transceiver into 120VAC and turn the unit on.FIGURE 2.2.2
3-1SECTION 3OPERATING INSTRUCTIONS3.1 GENERALThis section contains instructions for proper operation of the TDP-90 software and explainsthe various elements of the Graphical User Interface (GUI).NOTE: The following images are examples only, and may not reflect your particular datasettings, or current TDP software version.3.2 GETTING STARTEDTo start the TDP-90 in Windows, simply click the Start menu > Programs > TiLTransceiver Data Programmer >TDP-90. The program will start, and the followingGraphical User Interface (GUI) will appear. The current version number is shown in squarebrackets on the title bar. The pull-down menus and icons provide the set-up and operatingfunctions. The Terminal window displays communication activity as it occurs. TheChannels pull-down tab provides selection for single or six channel transceivers. Thenumber of channels in the Frequency editing window changes accordingly. Select “1Channel TxRx” for the TSC-4400. The frequency, as displayed in the Frequency editingwindow, can be changed by clicking on the channel window and entering the frequency.Figure 3.3.1 - Main Graphical User InterfaceNote: ** Use of a mouse is highly recommended! ** It is possible however, to use the TDPsoftware without a mouse by using the [Tab], [Shift]+[Tab] and 'cursor' keys to navigate throughthe program interface. You will note that all menu items and buttons have an underlined letter. Bypressing the [Alt] key and the underlined letter in the menu bar or button, you can pull down thatmenu item. eg: [Alt]+F, would pull down the file menu. You could then cursor down to the desiredfunction, or press the underlined letter for the corresponding function.
3-23.3 PULL DOWN MENUSThe TDP-90 program has several functions available through the use of pull-down menus.Through these menus, you can invoke file functions, print the channel list, initiatecommunications with a connected TFM-90 and quit the TDP software.3.3.1 File MenuFigure 3.3.1 - File MenuOpen will allow you to select and load and existing file that was previously saved on disk.The yellow folder icon provides the same function in a single mouse click.Save will allow you to save the current data into a file with a name of your choice. Thefilename may be any length up to 64 characters. The diskette icon provides the samefunction in a single mouse click.Print will create a text file of the channel list, as presented in the Frequency List window.Once the Print function is invoked, you will be prompted to enter the serial number of thecurrently connected transceiver. The printout will append a header to the top of the pagethat includes the serial number of the transceiver as well as the time and date. The printoutcan be filed as a record of the frequencies that are programmed into that particulartransceiver. The printer icon provides the same function in a single mouse click.Exit will quit the TDP-90 program. If you have not saved your data, or if any changes weremade to your data set since your last save, the TDP will warn you of this, and allow you todo so before quitting.
3-33.3.2 Data Transfer MenuFigure 3.3.2 - Data MenuDownload (to Radio) instructs the TDP-90 software to transfer the frequency data in thelist to the memory channels in the connected 8.33 kHz AM transceiver. The Dn iconprovides the same function in a single mouse click.Upload (from Radio) instructs the TDP-90 program to wait for and read the channel datafrom the memory channels in the connected 8.33 kHz AM transceiver. The Up iconprovides the same function in a single mouse click.Com1 (2,3,4) selects the COM (RS-232 Serial COMmunications) port on your computer, towhich the transceiver is connected. On computers manufactured after 1990, COM 1 istypically a 9 pin male "D" connector. COM 2 may be either a 9 pin male or 25 pin male "D"connector. COM 3 and COM 4 are available in the TDP-90 software as a valid option,although they typically exist only in a computer with a third party serial communicationscard installed.The COM port setting is automatically saved. The next time the TDP-90 software isexecuted, the previously selected COM port will be used.NOTE: ** The TDP-90 software assumes you have an available and properly configuredCOM port, and assumes that a TSC-4400 transceiver is connected. **
3-43.3.3 Help MenuFigure 3.3.3 - Help MenuTDP-90-6R Help Contents will start the Windows Help dialog for the TDP-90 software.Here, you will find hardware connection and operating information as well astroubleshooting tips and answers to some Frequently Asked Questions.About displays Technisonic company and contact information as well as the revisionnumber of the TDP software in the “Terminal window” screen.
3-53.3.4 Channel SelectionFigure 3.3.4.1 - Single channelFigure 3.3.4.2 - Six channelsThe x Channel(s) pull-down tab allows you to select for single or six channel 8.33 kHz AMtransceiver use. The frequency editing window changes accordingly. Select “1 Channel TX/RX” for the TSC-4400.
3-63.4 SAMPLE UPLOAD AND DOWNLOAD1. Connect the computer to the transceiver and apply power as described in section 2.2.2. Run the TDP-90 program on the computer.3. Click on the Data pull-down list and select the serial port to which the transceiver is connected.4. Set the program for “1 channel TX/RX”.5. Turn on power to the transceiver.6. Click on the Up icon to retrieve the currently loaded frequency from the radio. You will see activity in the Terminal window as data is being transferred. 7. Edit the frequency as desired.8. Click on the Dn icon to copy the frequency to the transceiver. You will see activity in the Terminal window as data is being transferred. 9. Click on the diskette icon to save the file.10. Click on the printer icon to print a hard-copy of the frequencies.3.5 RS-232 SERIAL TECHNICAL DATAThe TDP-90 communicates with a connected transceiver at 9600 Baud, 8 Data bits, noParity and 1 Stop bit. The TDP software sets these communications parameters uponstartup, independent of the Windows default settings for the COM port you are using.These communications parameters are not user configurable.

Navigation menu