Technologies Humanware PGI400 Prodigi Connect 12 User Manual V2 0

Technologies Humanware Inc. Prodigi Connect 12 V2 0

user manual

Connect PGI-400 Quick Start Guide
Box Contents
Tablet, Power Supply cable, Quick Start
Guide, Getting Started Guide, User
Guide, Warranty Sheet.
Overview
1. Micro-SD slot
2. USB-C port
3. Recharge port
4. Micro-HDMI port
5. Headphone jack
6. Speakers
7. Front-facing camera
8. Volume Down-Up
9. Power Button
10.Camera
Getting started
1. Connect the power supply
cable to the recharge port
and plug it to an outlet.
2. Allow the tablet to charge until
the battery is full.
3. Press and hold the Power
button to power on your tablet;
allow 30 seconds to initialize.
Recharging the battery
Connect the power supply cable
to the Tablet and plug it to an
outlet. After initial recharge, a
recharge requires 4 hours.
Battery safety precautions
Do not disassemble or modify the battery. There is a risk of overheating, fire
or explosion if the battery is put in a fire, heated, subjected to impact, put in
contact with water, or if its terminals are shorted.
7
10
1
2
3
4
89
5
6
Connect PGI-400 Quick Start Guide
FCC / Industry Canada Two Part Stmt
This device complies with FCC Part 15 and Industry Canada license exempt
RSS standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired operation of the
device.
Per Industry Canada RSS rules
This device complies with HeaOWK&DQDGD¶V6DIHW\&RGH7KHLQVWDOOHURIWKLV
device should ensure that RF radiation is not emitted in excess of the Health
&DQDGD¶VUHTXLUHPHQW&KDQJHVRUPRGLILFDWLRQVQRWH[SUHVVO\DSSURYHGE\
WKHSDUW\UHVSRQVLEOHIRUFRPSOLDQFHFRXOGYRLGWKHXVHU¶s authority to operate
the equipment.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the Federal Communications
Commission (FCC) Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment causes
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, you are encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the space between the equipment and receiver.
-Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected.
-Consult your dealer or an experienced radio/TV technician for help.
Operating Temperature: 0 to 35 °C / 32 to 95 °F
Customer Support: 1 (800) 722-3393, support@humanware.com
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of
the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio/TV technician for help.

Navigation menu