Tecom Co AW4042UG 11G WLAN ADSL Router User Manual UserMan D6X AW4042UG

Tecom Co Ltd 11G WLAN ADSL Router UserMan D6X AW4042UG

Manual

- 1 -Quick Installation GuideAW4042U 4-Ethernet Port ADSL/ADSL2+ WiFi CPE1. Install AW4042U Back Panel Fig. 1.1 the Back Panel of AW4042U Label FunctionDSL RJ-45 connector: WAN interface to connect DSL line USB USB 2.0 connector: for printer and ext. Memory support TV RJ-45 connector: Connect to the PC Ethernet port, or to STB LAN 1- 3 RJ-45 connector: Connect to the PC Ethernet port. RST Reset button: Reset AW4042U to factory default setting. DC-IN Connect to the supplied power converter cable Table 1.1 Illustration of AW4042U Back Panel
- 2 -Front Panel There are 8 LEDs on the front panel which indicate the status of AW4042U showing as below: Fig. 1.2 the Front Panel of AW4042U Label Color Signalling FunctionFlashing System start-up Lighted Active connection Green Off Power-off / General MODEM error POWERRed Lighted Factory reset / FW updating Lighted Active data session Green Flashing Data transmission INTERNETRed Lighted No DSL correct user data Flashing PPPoE authentication ongoi Lighted PIN OK and active PPPoE Session Green Flashing Data transmission Lighted Waiting Pin insertion INFORedFlashing PIN OK, waiting authentication Lighted Wireless on Flashing Data transmission WLAN Green Off Wireless off SlowFlashing sending pilot tones FastFlashing DSL training Lighted DSL synchronized DSL Green Off internal DSL error Flashing Data transmission Lighted active connection LAN1- 3/TV Green Off no active connection WLAN on/off : long press WLAN On/off WPS: short press Table 1.2 Illustration of AW4042U Back Panel
- 3 -Connecting the Hardware WARNINGBefore you begin, turn the power off for all devices.These include your computer(s), your LAN hub/switch (if applicable), and the AW4042U. The layout of the ports on your device may vary from the layout shown. Refer to the steps that follow for specific instructions. Figure 1.3. Overview of Hardware Connections 2. Login to AW4042U through web browser I. Configure your PC IP address as 192.168.1.x within the same subnet as AW4042U (AW4042U default IP is 192.168.1.1) and subnet mask (default is 255.255.255.0). II.Connect AW4042U with PC through an Ethernet cable. a. Turn on the power of AW4042U to establish ADSL link. b. Enter the IP address (default is 192.168.1.1) of AW4042U from Web Browser. Login Dialog Box will pop up as following:
- 4 -Fig. 2.1 Login Dialog Boxc. Enter the management Username/Password and click the OK button (The default Username/Password isadmin/admin). d. The first page will show the first page of Quick Setup. Follow the instructions to configure the AW4042U. 3. Quick Setup I. Set up ATM PVC and QoS II. Configure WAN Interface
- 5 -III. Enable/Disable Bridging Service IV. Configure LAN IP Address and Subnet Mask
- 6 -V. Setup the Wireless LAN
- 7 -VI. Save & Reboot
- 8 -5. USB To connect USB devices, the IAD provides an USB 2.0 port. I. Print Server AW4042U includes a print server that allows connecting one printer via USB. All PCs of the IAD have access to these printers. a. Go to Advanced Setup – Print Server to Enable Print Server Service b. Enter the Printer Name then Click Save/Apply c. Enter \\192.168.1.1 in the Web Browser and Locate the Network Printer in the Network.
- 9 -II. Network Storage AW4042U provides a file server utility, allowing you to manage (read/write/delete) files on a Network Attached Storage (NAS, i.e. hard disc or memory stick). AW4042U supports external hard discs up to a maximum of 5V/500mA which is 2.5W. When a hard disc needs more power, then this hard disc needs an own power supply. AW4042U does support FAT32, NTFS and Linux/Unix (EXT2 / 3) file system. a. Connect the USB Hard Disk or Memory Stick to the USB Port b. Enter \\192.168.1.1 in the Web Browser and Locate the USB Drive. 5. Update Software and Restore default settings I. Update Software Fig. 5.1 Management – Update Software Click “Management->Update Software” on the left frame. Locate the location of the software image, or select the file by browsing the file system. Click ‘Update Software’ button and the system will reboot after update complete. II.Restore Default Click “Management-> Settings->Restore Settings” on the left frame. Click ‘Restore Default Settings’ button to reset AW4042U to the factory defaults. Fig. 7.2 Tools – Restore Default Settings
- 10 -6. Change Password Click “Management-> Access Control->Passwords”, input the data and click “Save/ Apply”Fig. 6.1Access Control--Passwords9. Wireless Click “Wireless”, input the data and click “Save/ Apply” as Figure 9.1 Wireless -- Basic.Figure 9.1 Wireless – Basic
- 11 -Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. -This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels 1 through 11. IMPORTANT NOTE: FCC Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The availability of some specific channels and/or operational frequency bands are country dependent and are firmware programmed at the factory to match the intended destination. The firmware setting is not accessible by the end user.

Navigation menu