Tecom Co FP8134T 3G Femtocell Access Point User Manual

Download:
Mirror Download [FCC.gov]
Document ID	1826011
Application ID	8x2n5KLety5Qb4nGXXxFrg==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	26.14kB (326742 bits)
Date Submitted	2012-10-30 00:00:00
Date Available	2012-11-15 00:00:00
Creation Date	2012-10-22 14:53:57
Producing Software	Acrobat Distiller 7.0 (Windows)
Document Lastmod	2012-10-29 15:29:15
Document Title	Microsoft Word - QIG 安裝手冊_101.10.16_
Document Creator	PScript5.dll Version 5.2
Document Author:	TracyTing

QUICK START GUIDE
1. WHAT IS IN THE BOX
Femtocell with optional wall
fixings (where included)
Data cable to connect the
Femtocell to your broadband
router or cable modem
Mains power supply adaptor and
plug
External GPS Antenna
(Optional)
2. CHOOSING THE BEST LOCATION
Before installing, think about where you want to put your new
Femtocell. The ideal location is somewhere central, away from
windows – this will allow the Femtocell to give the best
coverage possible.
3. HOW TO INSTALL YOUR FEMTOCELL
STEP 1 – Insert the SIM Card
Insert the SIM card provided by your Network Operator with
the Femtocell. The SIM card will not lock in place if it is
inserted incorrectly – please take care not to force the SIM
card in to the slot.
STEP 2 – Connect the network cable
Connect one end to the Femtocell and the other end to your
broadband router or cable modem.
STEP 3 – Connect the power adaptor and then switch on at the
mains
STEP 4 – Wait 10 minutes for the Femtocell to be ready to use
The green light will stop flashing and become solid green
when the Femtocell is ready to use
4. IN THE EVENT OF A PROBLEM
If the Red light is on then that means there is a problem with the device.
If the Red light is not flashing then please contact customer care who will
help you with the problem.
If the red light is flashing this means there is a problem which you can
resolve yourself. The number of flashes indicates the type of problem as
shown below:
Number
of
flashes
Problem
Recommended action
No connection to local Check the connection between the
broadband router
broadband router and the Femtocell.
No internet
connection
Check that the broadband router is
connected to the Internet and is
providing service.
Interference problem
There is interface with other systems.
Try placing the Femtocell in a different
place. If this persists please contact
customer services.
Overheating
Check the Femtocell is located where
there is good airflow.
SIM card problem
Check to see that the SIM card is the
one provided with the Femtocell and
that it has been inserted correctly. If it
is please contact customer services.
5. PRODUCT CARE & USAGE
All instructions, warning and caution statements that accompany this equipment must be
strictly followed at all times to ensure its safe use. Observe all warning and caution symbols
that are fixed to this equipment.
Do not cover the device or block the airflow to the device with any other objects
To be in compliance with regulations, the user must use the cables supplied with the unit and
install them properly. This includes the power adapter that is provided.
Operate this product only with the type of power source indicated on the marking label. If you
are not sure of the type of power supplied to your home, consult your dealer or local
electricity company.
Do not use this product near water, for example a swimming pool or a bathroom. Keep the
device away from excessive heat and humidity and keep the device free from vibration and
dust.
Federal Communication Commission Interference Statement
This device has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against such interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy. If not installed and used in accordance with
the instructions, it may cause harmful interference to radio communications. However, there
is no guarantee that interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be determined by
turning the equipment OFF and ON, the user is encouraged to try to correct the interference
by one or more of the following measures:
Reorient or relocate the receiving antenna, if applicable.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the service provider or an experienced radio/television technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
The information shown in the FCC Declaration of Conformity paragraph below is a
requirement of the FCC and is intended to supply you with information regarding the FCC
approval of this device.
Declaration of Conformity
Description:
Model:
FCC ID:
3G Small Cell
FP8134T
D6XFP8134T
This device complies with Part 15 of FCC Rules. Operation is
subject to the following two conditions:
The device may not cause harmful interference.
The device must accept any interference received, including
interference that may cause undesired operation.
Canada EMI Regulation
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la class B est conforme à la norme NMB-003 du Canada.
This device complies with RSS-132 and RSS-133 of the Industry Canada Rules.
Operation is subject to the following two conditions:
This device may not cause harmful interference.
This device must accept any interference received, including interference that
may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC’s RF radiation exposure limits set forth for an uncontrolled
environment under the following conditions:
This device should be installed and operated such that a minimum separation distance of 8
inches (20 cm) is maintained between the radiator (antenna) and the user’s or nearby
person’s body at all times.
This transmitter must not be co-located or operated in conjunction with any other antenna or
transmitter.
For more information, visit the FCC website at http://www.fcc.gov
Disclaimer
NEC assumes no responsibility for errors or omissions that may appear in this guide. We
reserve the right to change this guide at any time without notice.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print, Print high-res
XMP Toolkit                     : Adobe XMP Core 4.0-c316 44.253921, Sun Oct 01 2006 17:14:39
Producer                        : Acrobat Distiller 7.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2012:10:29 15:29:15+08:00
Create Date                     : 2012:10:22 14:53:57+08:00
Metadata Date                   : 2012:10:29 15:29:15+08:00
Format                          : application/pdf
Title                           : Microsoft Word - QIG 安裝手冊_101.10.16_
Creator                         : TracyTing
Document ID                     : uuid:3a42c59a-a07a-4ce9-8779-05197086a567
Instance ID                     : uuid:c7848d36-f99b-48f8-ae3c-e8716b8e7378
Page Count                      : 4
Author                          : TracyTing

EXIF Metadata provided by EXIF.tools