Tecom Co IP3093 MOCET Communicator Mini User Manual U

Download:
Mirror Download [FCC.gov]
Document ID	2122028
Application ID	QYiU4bK4F/msqEoV9ZPG2A==
Document Description	user manual U
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	72.17kB (902093 bits)
Date Submitted	2013-11-19 00:00:00
Date Available	2013-11-19 00:00:00
Creation Date	2013-11-11 14:28:14
Producing Software	Acrobat Distiller 9.5.5 (Windows)
Document Lastmod	2013-11-11 14:29:28
Document Title	user manual U
Document Creator	PScript5.dll Version 5.2.2
Document Author:	MOCET Network Inc.

IP3093-U
Communicator mini
Quick User Guide
Copyright © 2013, All Rights Reserved.
Ver: R02 D/C: 102-1111
MOCET IP3093-U Communicator mini Quick User Guide
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible for
compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
CE Declaration of Conformity
This equipment complies with the requirements relating to electromagnetic compatibility, EN55022
class B for ITE and EN 50082-1. This meets the essential protection requirements of the European
Council Directive 89/336/EEC on the approximation of the laws of the Member States relating to
electromagnetic compatibility.
Environment
The device you have purchased, as well as any used batteries must not be disposed of with
household waste. You should return these to your distributor if they are to replaced or dispose of
them in an approved recycling center.
Trademarks
Android, Google and Nexus are registered trademarks of Google. Samsung and and Galaxy Note
are trademarks of Samsung Electronics Co., Ltd. iPad™ and iPhone™ are registered trademarks of
Apple Inc., USA. Windows, Skype and Lync2013 are trademarks of Microsoft Corporation in the
United States and/or other countries. Viber, Line and others as well as Unified Communications (UC)
apps, like CounterPath™ Bria™, Cisco™ Jabber™, Avaya™ one-X® Mobile, Radvision™ Scopia™,
Polycom™ RealPresenc™ or others are registered trademarks of their respective oeners.
WARNING!
▼
1. Read these installation instructions carefully before connecting the device to its power.
2. To reduce the risk of electric shock, do not remove the cover from the device or attempt to
3.
4.
5.
dismantle it. Opening or removing covers may expose you to dangerous voltage levels.
Equally, incorrect reassembly could cause electric shock on re-use of the appliance.
Do not expose the device to Fire, direct sunlight or excessive heat.
Do not expose the device to rain or moisture and do not allow it to come into contact with
water.
Do not install the device in an environment likely to present a THREAT OF IMPACT.
Page
MOCET IP3093-U Communicator mini Quick User Guide
6. You may clean the device using a fine damp cloth. Never use solvents (such as
trichloroethylene or acetone), which may damage the device’s plastic surface. Never spray
the device with any cleaning product whatsoever.
7. The device is designed to work in temperatures from 5oC to 40oC.
8. The device must be installed at least 1 meter from radio frequency equipment, such as TVs,
radios, hi-fi or video equipment (which radiate electromagnetic fields).
9. Do not attempt to upgrade device in an unstable power environment. This could cause
unexpected issues.
10. Do not work on the system or connect or disconnect cables during lightning storms.
11. Children don't recognize the risks of electrical appliances. Therefore use or keep the phone
only under supervision of adults or out of the reach from children.
12. No repair can be performed by the end user, if you experience trouble with this equipment,
for repair or warranty information, please contact your supplier.
Page
MOCET IP3093-U Communicator mini Quick User Guide
Introduction
The MOCET™ Communicator mini™ is an innovative audio accessory that enables you to
use your mobile tablet or smart phone, like Google Nexus 7, or Nexus 4, Samsung Galaxy
series or Galaxy Note series, as a desktop phone with popular Social Networking apps like
Skype, Viber, Line and others as well as Unified Communications (UC) apps, like
CounterPath Bria Android Edition, Cisco Jabber Video, Avaya one-X® Mobile,
RADVISION’s SCOPIA Mobile, Polycom RealPresence Mobile, Microsoft Lync2013™, and
others, available from the Google Play Store and Windows Phone Store.
The high definition audio-enabled handset and speakerphone on the Communicator mini
dramatically enhances your communications and ensures privacy and comfort. For a large
office or medium to small sized conference room, there is even an optional desktop
microphone set available to ensure all participants in the room can be heard clearly on on
the call. For a more enjoyable multimedia experience, there is an available external
speaker to play high quality stereo audio when listening to music or watching movies or
YouTube videos.
The Communicator mini stand is adjustable between 0º and 125º, allowing you to find the
most convenient viewing angle for watching movies or participating in video conferencing
calls at your desk. The Communicator mini has a built-in fast charger so you can play and
work all day, and when you leave, your tablet or smart phone will be fully charged and
ready to go. Using the built-in USB host port, you can even charge a second phone or
mobile device.
And because it pairs using Bluetooth, Android tablet/smart phone, iPhone/iPad mini,
Windows phone and other Bluetooth-enabled devices can also benefit from the
Communicator mini’s HD handset and speakerphone for better call quality and comfort as
well.
What’s In the Package?
Page
MOCET IP3093-U Communicator mini Quick User Guide
1.
2.
3.
4.
Main unit x 1
Handset x 1
Handset cord x 1
Power adapter with cord x 1
5. Flip-side micro-USB connector module x 1
6. AUX-in cable x 1
7. Quick start guide x 1
8. Warranty card x 1
Setting up the Communicator mini™
1.
Use the right connector module
The Communicator mini supports two connector modules, one is regular micro-USB which
is for devices like Google Nexus 4, Samsung Galaxy series and Galaxy Note series, and
the other one is flip-side micro-USB which is for devices like Google Nexus 7. The default
module installed in the Communicator mini is a regular micro-USB connector. You can
follow the steps below to change it to the flip-side micro-USB connector module.
(A) Regular micro-USB
(B) Flip-side micro-USB
d l
d l
Step1: After unpacking the product package box, place the main body of the Communicator
mini top down in your lap or a firm sofa.
Step2: Insert two ballpoint pen refills into the two holes in the bottom of the Communicator
mini, and then, in parallel, push the ballpoint pen refills with a proper little force down
straight the regular micro-USB connector till it drops out.
Page
MOCET IP3093-U Communicator mini Quick User Guide
Step3: Place the Communicator mini on the table, and face to the Smile Face on the flipside micro-USB connector module, and insert it in the module cave firmly.
2.
Adjust the stand
Place the Communicator mini on the table and slightly pull the stand apart from the bottom
shell to a comfortable viewing position.
3.
Attach the handset
Attach the long end of the handset cord to the HAND port in the back of the Communicator
mini. Then, attach the short end to the handset. Run the cord through the cable guide so
that the Communicator mini does not wobble on the desk.
Page
MOCET IP3093-U Communicator mini Quick User Guide
4.
Plug-in the Power
Attach the cord of the power adaptor to the 12VDC port on back panel of the Communicator
mini. Plug the power cord into an outlet. When it is powered, the LEDs on the front panel of
main unit will light up and an alert sound will indicate that the Communicator mini is ready
to go.
5.
Connect the external speaker IP-SPKR (optional)
You can connect an external speaker to the SPKR jack in the back of the Communicator
mini.
Page
MOCET IP3093-U Communicator mini Quick User Guide
6.
Connect the external microphone IP-MIC (optional)
You can connect an external microphone to the MIC IN jack in the back of the
Communicator mini to improve the ability of others on a conference call to hear everyone in
the room.
Appearance and Buttons
The figures below show the appearance of both sides of the Communicator mini along with
the user interface buttons and handset.
The front panel is capacitive touch design to allow the user to control the volume of the
speaker, handset and headset of the Communicator mini. To make, answer, transfer,
join,hold or end a call, please use the controls on the tablet or smart phone app or built-in
phone app.
Page
MOCET IP3093-U Communicator mini Quick User Guide
Function Description for Interface of Communicator mini:
Speaker
For audio playing, ring and hands-free talking.
Micro-USB
connector
For Mobile device charging when it is seated on the MicroUSB connector. Also, data synchronization supported
between your Mobile device and a connected computer at
micro-USB port.
[Note]: If you need a connector for another type of device,
please contact MOCET directly.
Volume indicator
light bar
For current volume indication.
Press volume up button twice will turn on one more light.
Press volume down button twice will turn off one more light.
Volume control
Volume up () : Touch to raise the volume.
Volume down (–) : Touch to lower the volume.
Bluetooth
Touch and hold for 3 seconds to enter the pairing mode.
Slow blinking: Bluetooth is on pairing mode.
Steady on: Once the Bluetooth communication is
connected, the LED will be steadily lit and a hint sound will
be played.
AUX-in
Toggle this to switch audio path of the Mobile device either
AUX-in or Bluetooth.
Steady on: Audio from Mobile device is through the included
AUX-in cable instead of Bluetooth.
Page
MOCET IP3093-U Communicator mini Quick User Guide
Mute
Single touch to control Mute/Unmute of microphone(s). Or,
twice touches to Mute/Unmute both Mic(s) and speaker(s).
Steady on: Both microphone and speaker are all muted.
Slow blinking: Microphone is muted only.
[Note]: When mute is on, the external IP-MIC pair will be muted too. You
can mute the audio in the tablet or smart phone app or the built-in app.
Speaker
Touch to enable Communicator mini’s hands-free mode.
Steady on: Hands-free mode is enabled. (Default)
Microphone
For hands-free talking.
AUX-in Port
Connect to the headset port of your mobile device through
an AUX-in cable. This is useful in the event that your tablet
or smart phone app does not support Bluetooth audio.
PC synchronization
port
Micro USB port to connect to a computer through a micro
USB cable for data synchronization with your device.
Charging port
USB port for charging your second mobile device.
Cable tray (slot)
Put handset cord in the tray to prevent accident pull force on
the handset.
10
Hand
Handset connector for connecting the handset cord.
11
MIC IN
Microphone connector for connecting the external
microphone (IP-MIC). It is an optional accessory. Please
order the IP-MIC separately from MOCET.
12
EXT
Extension box connector. Not used.
13
Kingston lock mount Anti-theft device lock. Requires separate lock system.
14
12VDC
Power jack for connecting the included 12V/2A power
adapter.
15
SPKR
Speaker connector for connecting the external speaker (IPSPKR). It is an optional accessory. Please order the IPSPKR separately from MOCET.
16
Console
It is reserved for engineering usage only.
17
Upgrade
It is reserved for engineering usage only.
Docking and Charging Your Tablet or
Smart Phone
If your tablet or smart phone is in a case, please remove it from the case first, and then
connect it to the Communicator mini as shown in the figures below. While your mobile
device is docked on the Communicator mini, it will start charging automatically.
Page
10
MOCET IP3093-U Communicator mini Quick User Guide
Pairing Your Tablet or Smart Phone with
Bluetooth
1.
Prepare your tablet or smart phone
On your device, go to Settings > Connections > Bluetooth. Turn Bluetooth on. It may vary
by the mobile device that you are using. Please refer to the user manual of the mobile
device for operation instructions.
2.
Prepare your Communicator mini
Touch and hold the Bluetooth button on the Communicator mini for three (3) seconds, until
the Bluetooth button blinks. The Communicator mini is now in pairing mode. if you want to
stop pairing mode, touch and hold the Bluetooth button again for three (3) seconds.
3.
Pair your tablet or smart phone with the Communicator mini
Once your Communicator mini is listed as a device (appearing in the Bluetooth Devices list
with an ID like IP3093-XXXXXX), tap it to pair and connect to your tablet or smart phone.
When connected to the Communicator mini, if you want to disconnect Bluetooth
communication with your tablet, smart phone, touch and hold the Bluetooth button again for
three (3) seconds. The Bluetooth connection will disconnect.
Basic Operations
To use the Communicator mini, your tablet and smart phone not have to be docked; it will
either be connected by Bluetooth when in range of the Communicator mini, or connected
by the included AUX-in cable*. Here, we use Skype™ as an example.
1.
Making and answering calls
When you make a call, the Communicator mini speaker automatically comes on unless you
Page
11
MOCET IP3093-U Communicator mini Quick User Guide
pick up the handset. When a call comes in, the Communicator mini rings. To answer the
call, tap the Answer button
2.
Switching between devices during a call

Switching a call to your Communicator mini
Tap the Bluetooth button
Communicator mini.

Switching a call back to the tablet, or smart phone.
Tap the Speaker button
device.
3.
on the Skype™ app, the call will be switched to the
on the Skype™ app, the call will be switched to the Mobile
Adjusting the volume
You can either press the Volume buttons on the Communicator mini or on your tablet, or
smart phone volume switch to adjust the sound level.
4.
Synchronizing data
You can synchronize data such as music, photos and media files between your Mobile
device and the computer, through the Communicator mini.
1.
2.
3.
4.
5.
Install the tablet or smart phone’s PC suite on the computer.
Use a micro-USB to USB standard cable (not provided) to connect the computer and
the Communicator mini (Micro-USB port).
Connect your tablet, or smart phone to the Communicator mini. The computer will
recognize the device and mount it on the desktop or connect it to the PC suite.
To synchronize data between your Mobile device and the computer, please follow the
instructions provided with the application software.
Charging a second device using the USB host port on the Communicator mini
Page
12
MOCET IP3093-U Communicator mini Quick User Guide
You can use the USB port on the left side of the Communicator mini to charge a second
device. Using the charging cable included with the second device, connect it to the
Communicator mini USB port.
6.
Using the AUX-in cable instead of Bluetooth pairing
There are still quite a few apps for the tablet or smart phone that do not support Bluetooth.
Using the included AUX-in cable to connect with your device’s headset port to the
Communicator mini AUX-IN port will allow you to use these apps. When the AUX-in cable is
connected, audio will route automatically through the included AUX-in cable to the
Communicator mini. The AUX-in indicator light
will also turn steady blue.
Warranty Information
Thank you for your choice of product. Remember to record your Communicator mini
information below for further support service, if needed.
This device has Model number, Bluetooth ID and Serial Number which are located on the
back of the base unit. Please record them for service and support personnel.
Model Number:
IP3093-U
BT ID:
Serial Number:
Page
13

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Author                          : MOCET Network Inc.
Create Date                     : 2013:11:11 14:28:14+08:00
Modify Date                     : 2013:11:11 14:29:28+08:00
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Title                           : 
Creator                         : MOCET Network Inc.
Creator Tool                    : PScript5.dll Version 5.2.2
Metadata Date                   : 2013:11:11 14:29:28+08:00
Producer                        : Acrobat Distiller 9.5.5 (Windows)
Document ID                     : uuid:23b70c8e-e141-41e0-b0a9-9488573d21f6
Instance ID                     : uuid:14d17739-2315-4e4b-9bd5-fe3108294b3e
Page Count                      : 13

EXIF Metadata provided by EXIF.tools