Tecom Co USC3330BJ 3G Femtocell Residential Access Point User Manual usc3330install

Download:
Mirror Download [FCC.gov]
Document ID	2405095
Application ID	z2rCm/ce7tXrmJzECXzxZQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	32.49kB (406114 bits)
Date Submitted	2014-09-29 00:00:00
Date Available	2015-03-28 00:00:00
Creation Date	2017-10-21 01:52:22
Producing Software	GPL Ghostscript 9.18
Document Lastmod	2017-10-21 01:52:22
Document Title	usc3330install.book
Document Creator	FrameMaker 11.0.2
Document Author:	debbie

Cisco USC 3330
Quick Start Guide
Cisco Systems, Inc.
www.cisco.com
Text Part Number: 78-100476-01A0
Printed in the USA on recycled paper containing 10% postconsumer waste.
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S.
and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
Third-party trademarks mentioned are the property of their respective owners. The use of the word partner
does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual
addresses and phone numbers. Any examples, command display output, network topology diagrams, and
other figures included in the document are shown for illustrative purposes only. Any use of actual IP
addresses or phone numbers in illustrative content is unintentional and coincidental.
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the
Cisco website at www.cisco.com/go/offices.
© 2014 Cisco Systems, Inc. All rights reserved.
ii
78-100476-01A0
C O N T E N T S
Package Contents
Before You Begin
Connect Your Small Cell
Verify Your Small Cell Operation
Safety Instructions
Cisco USC 3330 Quick Start Guide
iii
iv
78-100476-01A0
Revised: September, 2014, 78-100476-01A0
Package Contents
Your Cisco Universal Small Cell (USC) 3330 is shipped with the following:
•
Power supply unit
•
Ethernet cable
•
This Quick Start Guide
Before You Begin
Consider where you want to place your new small cell. Place it on a flat
surface that is:
•
Somewhere central, away from windows so your small cell provides the
best possible coverage.
•
At least 30 cm (1 foot) from other wireless broadcasting devices to avoid
possible interference.
•
Convenient to connect to your broadband router or cable modem.
Cisco USC 3330 Quick Start Guide
Connect Your Small Cell
Follow these instructions to connect your USC 3330 for use:
Step 1
Connect one end of the network cable to the small cell Ethernet port
and the other end to your broadband router or cable modem.
Step 2
Connect the optionally provided GPS antenna to the GPS port
(MMCX connector). If used, locate the GPS antenna close to a
window, because GPS signals can be easily blocked by the building
infrastructure.
Step 3
Connect the power adapter to the power port and to an AC power
source.
Step 4
Wait ten minutes for your small cell to be ready to use.
The status LED stops flashing green and becomes solid green when
your small cell is ready to use.
78-100476-01A0
Figure 1
Cisco USC 3330 Connections
383206
GPS antenna port (MMCX)
Reset button
5V DC power port
Status LED
10/100 Base-T Ethernet port
Cisco USC 3330 Quick Start Guide
Verify Your Small Cell Operation
The LED display is located on the side of your small cell. Note the color and
activity of the LEDs and refer to this table to diagnose any problems:
Table 1
USC 3330 Status LED Indications
LED Indication
Small Cell State / Action
Off
No power—Ensure power supply is connected and
turned on.
Fast Green
Initialization or provisioning—Wait for action to
complete.
Green
In service, no calls or data sessions—Ready to support
calls.
Slow Green
In service with active calls or data sessions.
Red blink 1 time
in 4 seconds
No connection to local broadband router—Verify
connection between broadband router and small cell,
and verify that the broadband router is operational.
Red blink 2 times
in 4 seconds
No Internet connection—Verify that the broadband
router is connected to the Internet and is providing
service.
78-100476-01A0
Table 1
USC 3330 Status LED Indications (continued)
LED Indication
Small Cell State / Action
Red blink 3 times
in 4 seconds
Interference with other systems—Try placing your
small cell in a different place. If this problem persists,
contact customer support.
Red blink 4 times
in 4 seconds
Overheating—Verify that the small cell is located
where there is proper air flow.
Red
Initial boot—Wait up to 20 minutes; if still red, perform
a reset.
Cannot create secure connection—Contact customer
support.
Internal fault—Contact customer support.
RF issue, cannot select an RF profile—Verify whether
another small cell is located in close proximity and if
so, relocate unit.
Provisioning failure—Contact customer support.
Safety Instructions
Translated versions of the following safety warnings are provided in
Cisco USC 3330 Regulatory Compliance and Safety Information, located on
Cisco.com.
Cisco USC 3330 Quick Start Guide
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that
could cause bodily injury. Before you work on any equipment,
be aware of the hazards involved with electrical circuitry and
be familiar with standard practices for preventing accidents.
Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that
accompanied this device. Statement 1071
SAVE THESE INSTRUCTIONS
Warning
This product relies on the building’s installation for
short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than: 15A. Statement 1005
Warning
In order to comply with FCC radio frequency (RF) exposure
limits, antennas should be located at a minimum of 7.9 inches
(20 cm) or more from the body of all persons. Statement 332
78-100476-01A0
Warning
Read the installation instructions before you connect the
system to its power source. Statement 1004
Warning
Installation of the equipment must comply with local and
national electrical codes. Statement 1074
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note
Use only with listed ITE equipment.
If you require assistance installing or operating your small cell, contact
customer support.
For warranty information, refer to:
http://www.cisco-servicefinder.com/WarrantyFinder.aspx
Cisco USC 3330 Quick Start Guide
8
78-100476-01A0

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.6
Linearized                      : Yes
Encryption                      : Standard V4.4 (128-bit)
User Access                     : Print, Extract, Print high-res
Author                          : debbie
Create Date                     : 2014:09:10 15:29:02Z
Modify Date                     : 2014:09:26 11:39:40+08:00
Tagged PDF                      : Yes
XMP Toolkit                     : Adobe XMP Core 4.2.1-c043 52.372728, 2009/01/18-15:08:04
Format                          : application/pdf
Title                           : usc3330install.book
Creator                         : debbie
Creator Tool                    : FrameMaker 11.0.2
Metadata Date                   : 2014:09:26 11:39:40+08:00
Producer                        : Acrobat Distiller 11.0 (Windows)
Document ID                     : uuid:e9fd881c-f138-49d5-b17b-cb6c93d5fb61
Instance ID                     : uuid:1132d1d0-aae9-47c4-a628-59c860ae7785
Page Mode                       : UseOutlines
Page Count                      : 12

EXIF Metadata provided by EXIF.tools