Tecom Co USC3330BJ 3G Femtocell Residential Access Point User Manual usc3330install
Tecom Co Ltd 3G Femtocell Residential Access Point usc3330install
Tecom Co >
Contents
- 1. User Manual
- 2. User Manual Safety
User Manual
ii
78-100476-01A0
Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S.
and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
Third-party trademarks mentioned are the property of their respective owners. The use of the word partner
does not imply a partnership relationship between Cisco and any other company. (1110R)
Any Internet Protocol (IP) addresses and phone numbers used in this document are not intended to be actual
addresses and phone numbers. Any examples, command display output, network topology diagrams, and
other figures included in the document are shown for illustrative purposes only. Any use of actual IP
addresses or phone numbers in illustrative content is unintentional and coincidental.
Cisco has more than 200 offices worldwide. Addresses, phone numbers, and fax numbers are listed on the
Cisco website at www.cisco.com/go/offices.
© 2014 Cisco Systems, Inc. All rights reserved.
usc3330install.book Page ii Wednesday, September 10, 2014 10:28 PM
iv
78-100476-01A0
usc3330install.book Page iv Wednesday, September 10, 2014 10:28 PM
1
Cisco USC 3330 Quick Start Guide
Revised: September, 2014, 78-100476-01A0
Package Contents
Your Cisco Universal Small Cell (USC) 3330 is shipped with the following:
• Power supply unit
• Ethernet cable
• This Quick Start Guide
Before You Begin
Consider where you want to place your new small cell. Place it on a flat
surface that is:
• Somewhere central, away from windows so your small cell provides the
best possible coverage.
• At least 30 cm (1 foot) from other wireless broadcasting devices to avoid
possible interference.
• Convenient to connect to your broadband router or cable modem.
usc3330install.book Page 1 Wednesday, September 10, 2014 10:28 PM
2
78-100476-01A0
Connect Your Small Cell
Follow these instructions to connect your USC 3330 for use:
Step 1 Connect one end of the network cable to the small cell Ethernet port
and the other end to your broadband router or cable modem.
Step 2 Connect the optionally provided GPS antenna to the GPS port
(MMCX connector). If used, locate the GPS antenna close to a
window, because GPS signals can be easily blocked by the building
infrastructure.
Step 3 Connect the power adapter to the power port and to an AC power
source.
Step 4 Wait ten minutes for your small cell to be ready to use.
The status LED stops flashing green and becomes solid green when
your small cell is ready to use.
usc3330install.book Page 2 Wednesday, September 10, 2014 10:28 PM
3
Cisco USC 3330 Quick Start Guide
Figure 1 Cisco USC 3330 Connections
1GPS antenna port (MMCX) 4Reset button
25V DC power port 5Status LED
310/100 Base-T Ethernet port
1
2
3
4
5
383206
usc3330install.book Page 3 Wednesday, September 10, 2014 10:28 PM
4
78-100476-01A0
Verify Your Small Cell Operation
The LED display is located on the side of your small cell. Note the color and
activity of the LEDs and refer to this table to diagnose any problems:
Ta b l e 1 USC 3330 Status LED Indications
LED Indication Small Cell State / Action
Off No power—Ensure power supply is connected and
turned on.
Fast Green Initialization or provisioning—Wait for action to
complete.
Green In service, no calls or data sessions—Ready to support
calls.
Slow Green In service with active calls or data sessions.
Red blink 1 time
in 4 seconds
No connection to local broadband router—Verify
connection between broadband router and small cell,
and verify that the broadband router is operational.
Red blink 2 times
in 4 seconds
No Internet connection—Verify that the broadband
router is connected to the Internet and is providing
service.
usc3330install.book Page 4 Wednesday, September 10, 2014 10:28 PM
5
Cisco USC 3330 Quick Start Guide
Safety Instructions
Translated versions of the following safety warnings are provided in
Cisco USC 3330 Regulatory Compliance and Safety Information, located on
Cisco.com.
Red blink 3 times
in 4 seconds
Interference with other systems—Try placing your
small cell in a different place. If this problem persists,
contact customer support.
Red blink 4 times
in 4 seconds
Overheating—Verify that the small cell is located
where there is proper air flow.
Red Initial boot—Wait up to 20 minutes; if still red, perform
a reset.
Cannot create secure connection—Contact customer
support.
Internal fault—Contact customer support.
RF issue, cannot select an RF profile—Verify whether
another small cell is located in close proximity and if
so, relocate unit.
Provisioning failure—Contact customer support.
Table 1 USC 3330 Status LED Indications (continued)
LED Indication Small Cell State / Action
usc3330install.book Page 5 Wednesday, September 10, 2014 10:28 PM
6
78-100476-01A0
Warning
IMPORTANT SAFETY INSTRUCTIONS
This warning symbol means danger. You are in a situation that
could cause bodily injury. Before you work on any equipment,
be aware of the hazards involved with electrical circuitry and
be familiar with standard practices for preventing accidents.
Use the statement number provided at the end of each warning
to locate its translation in the translated safety warnings that
accompanied this device.
Statement 1071
SAVE THESE INSTRUCTIONS
Warning
This product relies on the building’s installation for
short-circuit (overcurrent) protection. Ensure that the
protective device is rated not greater than: 15A.
Statement 1005
Warning
In order to comply with FCC radio frequency (RF) exposure
limits, antennas should be located at a minimum of 7.9 inches
(20 cm) or more from the body of all persons.
Statement 332
usc3330install.book Page 6 Wednesday, September 10, 2014 10:28 PM
7
Cisco USC 3330 Quick Start Guide
Warning
Read the installation instructions before you connect the
system to its power source.
Statement 1004
Warning
Installation of the equipment must comply with local and
national electrical codes.
Statement 1074
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note Use only with listed ITE equipment.
If you require assistance installing or operating your small cell, contact
customer support.
For warranty information, refer to:
http://www.cisco-servicefinder.com/WarrantyFinder.aspx
usc3330install.book Page 7 Wednesday, September 10, 2014 10:28 PM
8
78-100476-01A0
usc3330install.book Page 8 Wednesday, September 10, 2014 10:28 PM