Tecom Co WM5030OD WiMAX Outdoor Modem User Manual WM5030 OD Mounting Guide V1 3

Download:
Mirror Download [FCC.gov]
Document ID	1292392
Application ID	Ml8hXHBP24WQANw87e7GDA==
Document Description	Users Manual 2
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	53.93kB (674154 bits)
Date Submitted	2010-06-08 00:00:00
Date Available	2010-06-08 00:00:00
Creation Date	2009-09-07 19:10:39
Producing Software	Acrobat Distiller 8.0.0 (Windows)
Document Lastmod	2010-05-13 14:48:09
Document Title	Microsoft Word - WM5030-OD-Mounting-Guide_V1.3.doc
Document Creator	PScript5.dll Version 5.2
Document Author:	tw2919

WM5030-OD WiMAX Outdoor Modem
Mounting Guide
Version 1.3
TECOM CO., LTD
2009/9/1
WM5030-OD MOUNTING GUIDE
Legal Rights
The material contained herein is proprietary, and owned by TECOM Co., Ltd or its third party licensors.
TECOM Co., Ltd reserves the right to alter the specification and description in this document without prior
notice.
Statement of Conditions
The information contained in this document is subject to change without prior notice. TECOM Co., Ltd
shall not be liable for errors contained herein or for incidental or consequential damages in connection with the
furnishing, performance, or use of this manual or equipment supplied with it.
Disclaimer
The software is sold on an “AS IS” basis. TECOM, its affiliates or its licensors MAKE NO WARRANTIES,
WHATSOEVER, WHETHER EXPRESS OR IMPLIED WITH RESPECT TO THE SOFTWARE AND THE
ACCOMPANYING DOCUMENTATION. TECOM SPECIFICALLY DISCLAIMS ALL IMPLIED WARRANTIES
OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT WITH
RESPECT TO THE SOFTWARE UNITS OF PRODUCT DELIVERED TO PURCHASER HEREUNDER ARE
NOT FAULT-TOLERANT AND ARE NOT DESIGNED, MANUFACTURED OR INTENDED FOR USE OR
RESALE IN APPLICATIONS WHERE THE FAILURE, MALFUNCTION OR INACCURACY OF PRODUCTS
CARRIES A RISK OF DEATH OR BODILY INJURY OR SEVERE PHYSICAL OR ENVIRONMENTAL
DAMAGE (“HIGH RISK ACTIVITIES”). HIGH RISK ACTIVITIES MAY INCLUDE, BUT ARE NOT LIMITED TO,
WM5030-OD MOUNTING GUIDE
USE AS PART OF ON-LINE CONTROL SYSTEMS IN HAZARDOUS ENVIRONMENTS REQUIRING
FAIL-SAFE PERFORMANCE, SUCH AS IN THE OPERATION OR NUCLEAR FACILITIES, AIRCRAFT
NAVIGATION OR COMMUNICATION SYSTEM, AIR TRAFFIC CONTROL, LIFE SUPPORT MACHINES,
WEAPONS SYSTEMS OR OTHER APPLICATIONS REPRESENTING A SIMILAR DEGREE OF POTENTIAL
HAZARD. TECOM SPECIFICALLY DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY OF FITNESS
FOR HIGH RISK ACTIVITIES.
PURCHASER’S SOLE REMEDY FOR BREACH OF THE EXPRESS WARRANTIES ABOVE SHALL BE
REPLACEMENT OR REFUND OF THE PURCHASE PRICE AS SPECIFIED ABOVE, AT TECOM’S OPTION.
TO THE FULLEST EXTENT ALLOWED BY LAW, THE WARRANTIES AND REMEDIES SET FORTH IN THIS
AGREEMENT ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES OR CONDITIONS, EXPRESS
OR IMPLIED, EITHER IN FACT OR BY OPERATION OF LAW, STATUTORY OR OTHERWISE, INCLUDING
BUT NOT LIMITED TO WARRANTIES, TERMS OF CONDITIONS OF MERCHANTABILITY, FITNESS FOR A
PARTICULAR PURPOSE, SATISFACTORY QUALITY, CORRESPONDENCE WITH DESCRIPTION, NON
INFRINGEMENT, AND ACCURACY OF INFORMATION GENERATED. ALL OF WHICH ARE EXPRESSLY
DISCLAIMED. TECOM WARRANTIES HEREIN RUN ONLY TO PURCHASER AND ARE NOT EXTENDED
TO ANY THIRD PARTIES. TECOM NEITHER ASSUMES NOR AUTHORIZES ANY OTHER PERSON TO
ASSUME FOR IT ANY OTHER LIABILITY IN CONNECTION WITH THE SALE, INSTALLATION,
MAINTENANCE OR USE OF ITS PRODUCTS.
Limitation of Liability
TECOM SHALL NOT BE LIABLE TO THE PURCHASER OR TO ANY THIRD PARTY, FOR ANY LOSS OF
PROFITS, LOSS OF USE, INTERRUPTION OF BUSINESS OR FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, PUNITIVE OR CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER ARISING UNDER
ii
WM5030-OD MOUNTING GUIDE
BREACH OF CONTRACT, TORT, NEGLIGENCE, STRICT LIABILITY OR OTHERWISE AND WHETHER
BASED ON THIS AGREEMENT OR OTHERWISE, EVEN IF ADVISED OR THE POSSIBILITY OF SUCH
DAMAGES.
TO THE EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL THE LIABILITY FOR
DAMAGES HEREUNDER OR ALVARION OR ITS EMPLOYEES OR AGENTS EXCEED THE PURCHASE
PRICE PAID FOR THE PRODUCT BY PURCHASER, NOR SHALL THE AGGREGATE LIABILITY FOR
DAMAGES TO ALL PARTIES REGARDING ANY PRODUCT EXCEED THE PURCHASE PRICE PAID FOR
THAT PRODUCT BY THAT PARTY.
IMPORTANT NOTE:
To comply with the RF exposure compliance requirements, the antenna(s) used for this
transmitter must be installed to provide a separation distance of at least 1 meter from all persons
and must not be co-located or operating in conjunction with any other antenna or transmitter. No
change to the antenna or the device is permitted. Any change to the antenna or the device could
result in the device exceeding the RF exposure requirements and void user’s authority to operate
the device.
iii
WM5030-OD MOUNTING GUIDE
TABLE OF CONTENTS
1.
UNPACK THE OUTDOOR MODEM........................................................................................................... 1
2.
HOW TO CONNECT .................................................................................................................................. 2
3.
BEFORE YOU START................................................................................................................................ 3
4.
MOUNTING WM5030-OD .......................................................................................................................... 6
5.
OMK ............................................................................................................................................................ 9
6.
APPENDIX: CONNECTING ETHERNET CABLE TO WM5030-OD ........................................................ 11
iv
WM5030-OD MOUNTING GUIDE
1.
UNPACK THE OUTDOOR MODEM
The following figure lists the items shipped with WM5030-OD outdoor modem:
1.
PoE Adapter: Qty 1
2.
1.5 M 8P4C gray Ethernet cable (between computer and PoE): Qty 1
3.
1 M 8P8C white Ethernet cable (between PoE and Modem): Qty 1
4.
Quick Installation Guide: Qty 1
5.
WM5030-OD outdoor modem: Qty 1
6.
Mounting kit: Qty 1
7.
RJ45 connector water sealing plug: Qty 1
8.
CD-ROM: Qty 1
9.
1.5M Power Cable for PoE Adapter: Qty 1
10.
Warranty Card : Qty 1
Note: The length of Ethernet cable required connecting outdoor modem and PoE adapter pending on
actual installation requirements, and it is thus not provided. The cable provided is for configuration
or testing purpose only – not for installation purpose.
Figure 1. WM5030-OD Outdoor Modem Package Contents
WM5030-OD MOUNTING GUIDE
2.
HOW TO CONNECT
In order to configure WM5030-OD outdoor modem, please take the following steps:
1.
Power is supplied thru the 8P8C Ethernet cable to outdoor modem, therefore it is important to use
8P8C Ethernet cable of adequate length to connect the RJ-45 connector located at the bottom of the
outdoor modem and the “Data & Power Out” port of PoE adapter.
2.
Connect the gray Ethernet cable between the “data in” port of the PoE adapter and subscriber’s
personal computer.
3.
Plug the PoE adapter power cable to power outlet
4.
Plug the OMK (Outdoor modem Monitoring Kit) to OMK connector
Figure 2. Typical Installation Diagram
WM5030-OD MOUNTING GUIDE
3.
BEFORE YOU START
3.1 Mounting Location
Choosing a good mounting location for the outdoor modem is important because it affects the reliability of the
wireless link and maximum data rates it can support. The most important considerations are distance from
base station and clearance from obstacles. The mounting location can be a wall, ceiling, the top or side of a
building, or on a tower providing a clear unobstructed line-of-sight to the base station to provide the best
performance. Line-of-sight to the base station is not required, but provides best performance for subscriber.
With the high gain panel antenna outdoor modem configuration, the location must allow the antenna to be
oriented in the proper direction. The outdoor modem can be located in a convenient location that minimizes the
cable length to the outdoor modem.
When choosing mounting location, try to avoid the following common obstacles:
„
Trees and large plants: Remember to include allowance of future tree growth.
„
Man-made obstacles: A large round container such as a gas storage reservoir or water tower that is
partially in the path causing some blocking. These obstacles may also reflect some energy, which
can interfere with other receivers. Square or rectangular objects in or near the path have rectangular
surfaces that can block and diffract signals over and around them.
Make sure the following cable route requirements are met before beginning the installation:
WM5030-OD MOUNTING GUIDE
„
Identify cable routes, building entry points, and any special routing or support requirements
(conduits, bracing, cable trays, safety structures, and so on). Make sure the total cable length
between the outdoor modem and the PoE is no longer than 100 meters.
„
Identify necessary floor, roof, or wall penetrations and specify the locations.
„
Document existing grounding system and connection requirements for new equipment.
„
Refer to electrical codes for your local regulations
3.2 Lighting Protection
In outdoor installations, your outdoor modem can be damaged by surges that develop on the antenna and
cable from close lightning strikes. You can use a lightning arrestor to help protect your outdoor modem from
static electricity and lightning-induced surges; however, an arrestor will not prevent damage from a direct
lightning hit.
3.3 Safety Precautions
„
For your safety, and to help you properly install hardware, please read and follow these safety
precautions.
„
If you are installing an outdoor modem for the first time, for your own safety as well as others, seek
assistance from a person with skills and knowledge related to the construction and operation of electrical
equipment and has received safety training on the hazards involved.
„
Keep safety as well as performance in mind when selecting your installation site. Remember: electric
power lines and phone lines look alike. Always assume that overhead lines are very dangerous.
WM5030-OD MOUNTING GUIDE
„
Call your electric power company. Tell them your plans, and ask them to look at your proposed
installation. This is a reasonable request considering the danger.
„
Plan your installation carefully and completely before you begin. Successful rising of a mast or tower is
largely a matter of coordination. Assign each person a specific task, and ensure that they know what to do
and when to do it. Put one person in charge of the operation to issue instructions and watch for signs of
trouble.
„
„
When installing your antenna, remember:
Do not use a metal ladder.
Do not work on a wet or windy day.
Do dress properly—shoes with rubber soles and heels, gloves, long sleeved shirt or jacket.
If the assembly starts to fall, get away from it and let it fall. Remember: the antenna, mast, cable, and
metal guy wires are excellent conductors of electrical current and may touch power lines.
„
If any part of the outdoor modem comes in contact with a power line, don’t touch it or try to remove it
yourself. Call your local power company. They can remove it safely. If an accident occurs with the power
lines, call for qualified emergency help immediately.
3.4 Tool
„
Spanner
„
Flat screwdriver
„
Crimpers
„
Cable stripping tool
„
Cutting tools
„
RJ-45 connectors
„
Category 5E Ethernet cable of proper length (8P8C, 24 AWG)
„
Cable tester
WM5030-OD MOUNTING GUIDE
4.
MOUNTING WM5030-OD
4.1 Polarization
Polarization helps reduce interference because the antenna tends to reject cross-polarized signals from other
sources. Please contact your base station vendor for information on polarization. Orient WM5030-OD
according to the base station polarization. For example, BTS use the vertical polarization for antenna 0
(preamble path), and horizontal polarization for antenna 1 (secondary path), the WM5030-OD should be
mounted by vertical polarized for T/R path and horizontal polarized for R path. If BTS uses the dual slant 45
polarization, and +45 degree for antenna 0 (preamble path), and -45 degree for antenna 1 (secondary path),
the WM5030-OD should be mounted by -45 degree polarized for T/R path and +45 degree polarized for R path.
Figure 3. Polarization of WM5030-OD
WM5030-OD MOUNTING GUIDE
4.2 Mounting
„
Mounting on pole
A.
The metal bands supplied with WM5030-OD, support pole diameter of 75mm~90mm. Run the
metal bands thru the elevation clamp and the pole to fix the mounting unit to the pole. Do not tight
the screws fully at this point yet, but tight enough to support the weight of WM5030-OD. You will
need to orient the WM5030-OD for best reception later.
B.
Fasten the mounting clamp to the WM5030-OD with screws provided.
C.
Fasten WM5030-OD on the pole by fastening bolts and nuts provided thru mounting clamp and
elevation clamp.
D.
Connect Category 5E Ethernet cable to the RJ-45 connector located at the bottom of WM5030-OD.
(refer to appendix)
E.
Connect OMK (please refer to next section for details of OMK) to the OMK connector located at the
bottom of WM5030-OD. Make sure the power LED is on. Please check Ethernet cable and PoE
connection if the power LED is not on.
F.
OMK (Outdoor modem Monitoring Kit) provides you the signal strength (CINR) with CINR LED.
Orient WM5030-OD when you have more than 7 or more CINR LED off.
G.
If base station is nearby, and locates higher or lower than WM5030-OD, then adjust the tilt of
WM5030-OD accordingly. Use the elevation indication labels on the elevation clamp to find the
best tilt for best CINR.
„
Wall mount
A.
Connect Category 5E Ethernet cable to the RJ-45 connector located at the bottom of WM5030-OD
(please refer to appendix)
WM5030-OD MOUNTING GUIDE
B.
Connect OMK (please refer to next section for details of OMK) to the OMK connector located at the
bottom of WM5030-OD. Make sure the power LED is on. Please check Ethernet cable and PoE
connection if the power LED is not on.
C.
OMK (Outdoor modem Monitoring Kit) provides you the signal strength (CINR) with CINR LED.
Position WM5030-OD when you have more than 7 or more CINR LED on. Use a marker to mark
this position for wall mount.
D.
Screw the elevation clamp to the wall.
E.
Fasten the mounting clamp to the WM5030-OD with screws provided.
F.
Fasten WM5030-OD on the wall by fastening bolts and nuts provided thru mounting clamp and
elevation clamp.
G.
If base station is nearby, and locates higher or lower than WM5030-OD, then adjust the tilt of
WM5030-OD accordingly. Use the elevation indication labels on the elevation clamp to find the
best tilt for best CINR.
WM5030-OD MOUNTING GUIDE
5.
OMK
OMK (Outdoor modem Monitoring Kit) is a convenient tool for technician during installation, testing and
maintenance for WM5030-OD. It is designed for easy carrying and an excellent tool to display radio quality for
technician to adjust orientation and tilt of WM5030-OD for best reception from WiMAX base station. OMK
features include:
CINR signal quality
Link status
Power indicator
Reset to factory default
Figure 4. OMK
WM5030-OD MOUNTING GUIDE
Table 1. Definitions of OMK LED
Color
Function
CINR
31 ≥
29 >
27 >
24 >
20 >
15 >
10 >
CINR
Signal
CINR ≥
CINR ≥
CINR ≥
CINR ≥
CINR ≥
CINR ≥
CINR ≥
< 5dBm
Indicator
31dBm
29dBm
27dBm
24dBm
20dBm
15dBm
10dBm
5dBm
WiMAX
Saturate
Green
Red
RSSI > -20dBm: ON (saturate)
LED
WiMAX
Green
Operational: ON
Not in operation: OFF
Link
LED
Power
Green
Power-on: ON, Power-off: OFF
LED
Reset
Push and hold for 20 seconds will reset WM5030-OD to factory default
Button
10
WM5030-OD MOUNTING GUIDE
6.
APPENDIX: CONNECTING ETHERNET CABLE TO WM5030-OD
This appendix explains how to prepare and connect Ethernet cable to WM5030-OD. The Ethernet cable
assembly is shown below.
Figure 5. Ethernet Cable Assembly
Step 1：Assemble the water proof unit as follows:
Step 2: Peel the Ethernet cable as follows:
Step 3：Run the Ethernet cable thru water proof units.
11
WM5030-OD MOUNTING GUIDE
Step 4.
Step 5.
Step 6.
Step 7.
Step 8. You are ready to connect the Ethernet cable to WM5030-OD. Please prepare the other
end and make connection to the PoE adapter.
12

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : Yes
Encryption                      : Standard V1.2 (40-bit)
User Access                     : Fill forms, Extract, Assemble, Print high-res
Create Date                     : 2009:09:07 19:10:39+08:00
Modify Date                     : 2010:05:13 14:48:09+08:00
Producer                        : Acrobat Distiller 8.0.0 (Windows)
Mod Date                        : 2010:05:13 14:48:09+08:00
Creation Date                   : 2009:09:07 19:10:39+08:00
Author                          : tw2919
Creator Tool                    : PScript5.dll Version 5.2
Metadata Date                   : 2010:05:13 14:48:09+08:00
Document ID                     : uuid:2cd0f5e8-b733-446a-a53c-e6a78a304312
Instance ID                     : uuid:a8fa367a-27ed-4934-b2f2-71bc23707eda
Format                          : application/pdf
Title                           : Microsoft Word - WM5030-OD-Mounting-Guide_V1.3.doc
Creator                         : tw2919
Page Count                      : 17
Has XFA                         : No

EXIF Metadata provided by EXIF.tools