Tele Radio i Lysekil C1303A Transceiver Radio Modular User Manual CE TG2002 A01 EN
Tele Radio AB Transceiver Radio Modular CE TG2002 A01 EN
UserManual.wiki
>
Tele Radio i Lysekil
>
C1303A User Manual
User Manual
Navigation menu
Upload a User Manual
Namespaces
Wiki Guide
HTML
PDF
Info
Views
User Manual
Discussion / Help
Navigation
![Chapter 5: INSTALLERS GUIDECHAPTER 5: INSTALLERS GUIDECREATE PIN CODESNOTE! You can store up to 10 PIN codes in the transmitter. NOTE! '0000' is not a valid PIN code. 1. Make sure that the stop button is pressed.2. Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).3. Press the right start button. Keep pressed.4. Press the stop button. 5. Release the right start button.The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 6. Go to [Enter PIN].7. Select what position in the list that you want to store the new PIN code in by pressing the left start button. 8. Enter the new PIN code (4 digits) by pressing the buttons 1-4: PRESS BUTTON TO1 step up2 step down3 step right4 step left9. Confirm by pressing the left start button.ERASE PIN CODE1. Make sure that the stop button is pressed.2. Pull out the stop button.The LEDs light (green when the battery capacity is good, red when the battery capacity is poor).3. Press the right start button. Keep pressed.4. Press the stop button. 5. Release the right start button.The LEDs light (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 6. Go to [Erase PIN].-19 -](https://usermanual.wiki/Tele-Radio-i-Lysekil/C1303A/User-Guide-2139461-Page-19.png)
![Chapter 5: INSTALLERS GUIDE7. Scroll the list to select the PIN code that you want to erase. MOVEJOYSTICK TOup step updown step down8. Select by pressing the left start button.9. Confirm by pressing the left start buttons.SHOW REGISTERED PIN CODES1. Make sure that the stop button is pressed.2. Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).3. Press the right start button. Keep pressed.4. Press the stop button. 5. Release the right start button.The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 6. Go to [Show PIN].7. The display shows a list of all registered PIN codes. START THE TRANSMITTER IN OPERATING MODE1. Make sure that the stop button is pressed2. Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).3. If PIN codes are used for authorization: Go to the next section. 4. WITHIN 3 MINUTES FROM PULLING OUTTHESTOPBUTTON: Press a button to select the receiver(s) that you want to operate.The receiver(s) that was selected in the last session will be automatically selected, which is indicated by the corresponding LED(s) that light red. If no receiver(s) has been selected, the LEDs for all available receivers will flash red. If a receiver is selected, the LEDs next to the left and the right start buttons flash red. If no receiver(s) are selected, only the LED next to the right start button flashes red. 5. Press both start buttons at the same time.The buzzer beeps.6. Release the start buttons.The buzzer stops beeping. The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor).-20 -](https://usermanual.wiki/Tele-Radio-i-Lysekil/C1303A/User-Guide-2139461-Page-20.png)
![Chapter 5: INSTALLERS GUIDELOGIN/LOGOUTQuick logoutNOTE! When the transmitter has established radio communication with one or more receivers, you can make a Quick logout from those receivers. Note that the Quick logout will log the transmitter out from all receivers that are participating in the session. NOTE! If you need to log out a transmitter that is lost or damaged, it is possible to log out from the receiver. We do not recommend this way of logging out. Contact your representative for assistance. NOTE! To be able to control a receiver, the transmitter must be registered in the receiver, and logged in to the receiver. If another transmitter is already logged in to the receiver, it has to be logged out before any other transmitter can be logged in. If no transmitter is logged in to a receiver, a registered transmitter will automatically log in when sending radio signals to the receiver. The transmitter will stay logged in until it is manually logged out. More than one transmitter can be registered in the receiver, but only one transmitter can be logged in at a time.1. Make sure that the transmitter is started in operating mode. NOTE! The transmitter must have established a radio session with one or more receivers. 2. Press the left start button. Keep pressed.3. Press the stop button.4. Release the left start button.The top LED lights red.The display shows [Logging out].The transmitter turns off after logging out. LOGOUT FROM MENU MODE1. Make sure that the stop button is pressed.2. Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).3. Press the right start button. Keep pressed.4. Press the stop button. 5. Release the right start button.The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 6. Go to [Logout].7. Select by pressing the left start button.8. Select a receiver to log out from.9. Confirm by pressing the left start button. The display shows [Logging out...] while the process is ongoing.-22 -](https://usermanual.wiki/Tele-Radio-i-Lysekil/C1303A/User-Guide-2139461-Page-22.png)
![Chapter 5: INSTALLERS GUIDEIf logout fails, the display shows [FAILED]. The transmitter turns off.If logout succeeds, the display shows [OK]. The transmitter turns off after logging out. TURN THE TRANSMITTER OFF1. Press the stop button.The transmitter turns off. All relays deactivate. REGISTERIMPORTANT! Do not perform this when the receiver is in a session with another transmitter. The radio communication may become disturbed or broken. NOTE! Before starting to perform these settings, make sure that the stop relays are deactivated!Register the transmitter in the receiver 1. On the receiver: Select [Register Tx] from the display menu. 2. On the transmitter: Make sure that the stop button is pressed.3.On the transmitter: Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).4. On the transmitter: Press the right start button. Keep pressed.5. On the transmitter: Press the stop button. 6. On the transmitter: Release the right start button.The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 7. On the transmitter: Go to [Register] in the menu. Step down in the menu by pressing button 1. Step up in the menu by pressing button 2. Select by pressing the left start button. 8. On the receiver: Select [Yes] to start registering. The receiver will stay in registering mode for 1 minute or until a transmitter has been registered. 9. On the receiver: Confirm registering of the Tx by pressing the receiver joystick. 10. The receiver restarts. ERASEErase a transmitter from the receiverNOTE! If a transmitter is lost or becomes seriously damaged, it is possible to erase it from the receiver. We do not recommend this way. Contact your representative for assistance. -23 -](https://usermanual.wiki/Tele-Radio-i-Lysekil/C1303A/User-Guide-2139461-Page-23.png)
![Chapter 5: INSTALLERS GUIDENOTE! If the transmitter already have receivers registered, we recommend that you erase all receivers from the transmitter before starting the replacement. The receiver will automatically be stored in the same position as it was stored in the old transmitter. If this position is not available, the replacement will not take place. 1. Make sure that the stop button is pressed.2. Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).3. Press the right start button. Keep pressed.4. Press the stop button. 5. Release the right start button.The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 6. Go to [Erase]. 7. Select by pressing the left start button .8. Select a receiver. Confirm by pressing the left start button. The display shows [Erasing] while the process is ongoing. If the erasing fails, the display shows [FAILED]. The transmitter turns off.If the erasing succeeds, the display shows [OK]. The transmitter turns off.-24 -](https://usermanual.wiki/Tele-Radio-i-Lysekil/C1303A/User-Guide-2139461-Page-24.png)
![Chapter 5: INSTALLERS GUIDEREPLACEYou can replace a registered transmitter with another transmitter without having access to the receiver. IMPORTANT! If the transmitter that needs to be replaced is registered in more than one receiver, it will only be replaced in one receiver at a time. If you want to replace a transmitter in more than one receiver, you need to perform a replacement for each receiver. IMPORTANT! Do not perform this when the receiver is in a session with another transmitter. The radio communication may become disturbed or broken. NOTE! If the transmitter already have receivers registered, we recommend that you erase all receivers from the transmitter before starting the replacement. The receiver will automatically be stored in the same position as it was stored in the old transmitter. If this position is not available, the replacement will not take place. Replace a transmitter with a new transmitter1. Make sure that the stop button is pressed.2. Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).3. Press the right start button. Keep pressed.4. Press the stop button. 5. Release the right start button.The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 6. Go to [Replace]. Select by pressing the left start button.7. Enter the serial number/ID code for the transmitter that you want to replace by pressing the buttons according to the table below:PRESS BUTTON TO1 count -12 count +13 go left4 go right8.Press the left start button.The display shows [Replacing] while the process is ongoing.If the replacement fails, the display shows [FAILED].The transmitter turns off.If the replacement succeeds, the display shows [OK]. The transmitter turns off.AUTOMATIC SHUTDOWNTurning on automatic shutdown can save battery capacity by automatically turning the transmitter off when no function has been activated for a set time. -25 -](https://usermanual.wiki/Tele-Radio-i-Lysekil/C1303A/User-Guide-2139461-Page-25.png)
![Chapter 5: INSTALLERS GUIDESet the time for automatic shutdown1. Start the transmitter. 2. Enter menu mode. 3. Go to [Auto Shutdown]. Select by pressing the left start button.4. Select the time that you want for automatic shutdown: 0-255 minutes. If you want to turn off automatic shutdown, select 0. Confirm by pressing the left start button.FREQUENCIES & CHANNELSNOTE! If your system is transmitting on the frequency bands 433MHz or 2.4 GHz, the receiver will automatically detect and switch to the same channel that the transmitter is using. If your system is transmitting the 915 MHz frequency band, you have to switch bank in the receiver by using the PC program Settings manager. Contact your representative for assistance.Switch frequency bank on the transmitter1. Make sure that the stop button is pressed.2. Pull out the stop button.The top LED lights (green when the battery capacity is good, red when the battery capacity is poor).3. Press the right start button. Keep pressed.4. Press the stop button. 5. Release the right start button.The top LED flashes (green when the battery capacity is good, red when the battery capacity is poor) when in menu mode. 6. Go to [Channel/Bank]. 7. Select a bank. Confirm by pressing the left start button.Frequency band 915 MHzFrequency-hopping spread spectrum (FHSS) is a method of transmitting radio signals by rapidly switching a carrier among many frequency channels, using a pseudorandom sequence known to both transmitter and receiver. For further information about the frequencies used in this frequency band and about frequency-hopping, please contact your representative. -26 -](https://usermanual.wiki/Tele-Radio-i-Lysekil/C1303A/User-Guide-2139461-Page-26.png)
