Teledex AC9200 DECT HANDSET UNIT User Manual USERS MANUAL

Download:
Mirror Download [FCC.gov]
Document ID	844038
Application ID	9Glix35wd0DGq+s6dC9mlQ==
Document Description	USERS MANUAL
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	39.33kB (491654 bits)
Date Submitted	2007-09-17 00:00:00
Date Available	2007-09-18 00:00:00
Creation Date	2007-09-12 13:01:50
Producing Software	Adobe PDF Library 7.0
Document Lastmod	2007-09-13 10:31:14
Document Title	USERS MANUAL
Document Creator	Adobe InDesign CS2 (4.0.5)

iPhone DECT Cordless Series User Guide
For Models AC8205S, AC8210S (1.8 GHz) and AC9205S, AC9210S (1.9 GHz)
Included in Your Package
Cordless Handset
AC Adapter
Base Unit
User Guide
Lithium Polymer Battery
Clear Plastic Overlay
Rubber Battery Screw Cover
Phillips Screw
15-foot, 8-wire Cable
(with RJ-45 connector)
10-foot, 4-wire Line Cord
(with RJ-11 connector)
Preparing to Use the AC8200/AC9200 Series
1. Prepare to install the battery into the cordless handset
by removing the battery cover and sliding it off. If cover is
secured with a screw, remove the screw first.
2. Insert the battery connector into the handset’s connector.
The connector is “keyed” so it only goes in one way.
Do not force the connection.
Note: The handset may “beep” when the battery is
connected. This is not an indication that the telephone
is ready to use. To obtain optimal performance of the
telephone, be sure to charge the battery for 10 to 12 hours.
3. Replace the battery compartment cover and the
retaining screw.
4. Insert the provided rubber screw cover.
5. Turn the telephone base so the back panel is facing you.
Insert either end of the RJ-45 cable into the jack on the 			
back of the telephone labeled LINE.
6. Insert the other end of the cable into the jack on the AC
adapter labeled PHONE.
7. Insert one end of the RJ-11 line cord into the jack on the 		
AC adapter labeled LINE.
8. Insert the other end of this line cord into a telephone jack.
9. Plug the AC adapter into an unswitched electrical outlet.
10. Remove the plastic overlay and place the paper faceplate
		 (supplied separately) over the keys. Replace the plastic
		 overlay by hooking the tabs on the overlay into the
		 recessed slots located on both sides.
11. Place the cordless handset on the base unit.
		 The handset/base registration process will occur.
Handset/Base Registration Procedure
This procedure establishes an exclusive link between a specific
handset and base, thereby allowing no other access to this
specific base. To accomplish this procedure, place the handset
on the base in the charging position. The LINE indicator will
blink while the registration process is occuring. This process
only occurs the first time a handset is placed on the charging
cradle of a new base.
Charging the Battery
The rechargeable Lithium-Polymer battery must be fully
charged before using the phone for the first time.
It is recommended that the battery be charged for approximately 10 to 12 hours without interruption before use.
To charge the battery, place the handset, keypad down, in the
base unit. Ensure that the CHARGE LED on the base lights.
If the LED Does Not Light:
1. Ensure that the AC adapter is plugged in.
2. Ensure that the AC adapter is plugged into an unswitched
electrical outlet.
3. Ensure that the handset charging contacts at the bottom of
the handset are making good contact with the base unit’s
charging contacts.
Cleaning the Battery Contacts
To maintain a good charge, it is important to clean all
charging contacts on the handset and base unit. Use a
pencil eraser or other contact cleaner. Do not use any
liquids or solvents.
Battery Safety Instructions
1. Use only Teledex-approved battery replacements.
2. Dispose of the Lithium-Polymer battery in any ordinary 		
trash receptacle.
3. Do not dispose of battery in fire, as it may explode.
4. Charge the battery only while in the handset, and only by
using the base unit to charge. Do not attempt to remove
the battery and charge it in a separate charging unit.
5. Do not short-circuit the battery, as this may cause it to
explode or catch fire.
Adjusting the Ring Volume and Assigning Ring Tones
The UP and DOWN volume keys will adjust the ringer volume
of the telephone. To adjust ring volume, press either the UP
and DOWN volume key when the handset is on the bse cradle
and the phone is not active (off-hook).
There are four ring tones that can be assigned individually
to either line (on two-line models) to audibly identify the
ringing line. Additionally, the AC8200/AC9200 series features
a programmable “crescendo” ring mode, wherein the ring
volume begins at the lowest setting, then rings progressively
louder with each ring during an incoming call.
To assign a ring tone to a line (normal ring mode):
1. Press the FLASH key (see Fig. 1); then a key on the dial pad
from 1-4, depending on the desired ring tone. The phone
will ring once to provide a sample of the selected ring
tone.
2. When you have selected a suitable ring tone, press the
STORE key (see Fig. 1), then a number on the dial pad for
the desired line assignment (i.e.; ‘1’ for line 1, ‘2’ for line 2).
To assign a ring tone to a line (crescendo ring mode):
1. Select desired ring tone: Press the FLASH key (see Fig. 1);
then a key on the dial pad from 1-4, depending upon the
desired ring tone. The phone will ring once to provide a
sample of the selected ring tone.
2. Assign ring tone to a line: When you have selected a sui
able ring tone, press the STORE key (see Fig. 1), then press
number ‘3’ on the dial pad to assign the ring tone to line 1,
or number ‘4’ on the dial pad to assign the ring tone to
line ‘2’.
To return to regular ring mode:
1. Press the FLASH key; then the number ‘1’ on the dial pad.
2. Press the STORE key; then the number on the keypad that
corresponds to the line for which you wish to change back
to regular ring mode.
Adjusting Speakerphone Volume
The speakerphone has eight (8) levels. To adjust speakerphone volume, locate the volume up/down keys, located on
the front of the phone to the left of the keypad. With the
speaker active, press the “down” arrow key to decrease the
volume level, and press the “up” arrow key to increase it.
Adjusting Handset Receive Volume
The handset has eight (8) volume levels. To adjust the handset
volume, locate the volume up/down keys, located on the
handset, below the “#” key. Pressing the UP arrow key will
decrease the volume level, while pressing the DOWN arrow
key will increase it.
Auto Dial Keys
The AC8200/AC9200 series has either five (5) or ten (10)
programmable guest service (auto dial) keys, depending
on the model you own. These keys can be programmed
to automatically dial telephone numbers, or to activate
telephone system features. To program the auto dial
keys (programming can only be done from base unit):
1. With the phone “on hook” (inactive) and the faceplate
removed, press the recessed STORE key (see diagram).
2. Enter the desired telephone number (up to 15 digits in
length) to be stored. To enter a “pause” in the number
string, press the REDIAL key as necessary.
3. Press the STORE key again.
4. Press the auto dial key where the number is to be stored.
Programming is now complete for that auto dial key.
To program additional keys, repeat this process.
Selecting Line 1 and Line 2 (two-line models only)
The AC8200/9200 series employs PrimeLine/RingLine Select,
so selecting the correct line is as easy as lifting the handset.
This feature prioritizes the ringing or idle line and reduces the
confusion of line selection. You may also manually select the
desired line by pressing either Line 1 or Line 2 keys.
“off-hook” answering the ringing line.
3. To end the call, place the handset in the base unit cradle,
or press the illuminated line key on the handset.
To answer a call using the handset while it is resting on
the base:
1. Pick up the handset from the base. The phone will
automatically connect to the correct, ringing line.
2. To end the call, replace the handset in the base unit cradle,
or press the illuminated line key on the handset.
To answer a call using the speakerphone:
1. Press the line key for the ringing line. The speakerphone 		
will go “off-hook”, answering the ringing line.
2. Alternatively, press the SPKR key. The phone will automat
cally select the correct, ringing line.
3. To end the call, press the SPKR key or the active line
again.
Placing a Call
Using the handset:
1. Pick up the handset and select either line 1 or line 2.
Listen for dial tone and dial the desired number, or press
an auto dial key to dial a preprogrammed number.
2. After the call is complete, press the key for the selected 			
line again to end the call.
Using the speakerphone:
1. Press a key for either line 1 or line 2, or press SPKR.
2. Listen for dial tone, and dial the desired number, or press
an auto dial key to dial a preprogrammed number.
3. After the call is complete, press the SPKR key to end call.
Redial
The AC8200/AC9200 series can automatically redial the last
number dialed. On either the handset or base, press the
REDIAL key to redial the last number.
Conference (two-line models only)
The CONF key allows for three-way conversations. Depending
on the situation, you may initiate a conference call using one
of these methods:
User initiates two calls:
1. Place call to first party, then place them on hold by
pressing the HOLD key.
2. Using the second line, place call to second party.
3. Once that party is on the line, press CONF to join all three
parties.
User initiates one call:
1. After receiving a call from first party, place them on hold
by pressing the HOLD key.
2. Using the second line, place call to the second party.
3. Once that party is on the line, press CONF to join all three
parties.
Receiving a Call
An audible ring and flickering red LED indicate an
incoming call.
User includes two parties:
1. After receiving a call from first party, place them on hold
by pressing the HOLD key.
2. After receiving call from second party, press CONF to join
all three parties.
To answer a call using the handset while it is not on
the base:
1. Pick up the handset.
2. Press the line key for the ringing line. The handset will go
To terminate a conference call, pressing a line key will
maintain the connection with that line, while dropping the
other line. To terminate the call entirely, press either the
CONF key or SPKR key to disconnect both parties.
Using the Hold Key
The HOLD key places the call on hold locally at the cordless
telephone.
To Place a Call on Hold:
1. With a call active, press the red HOLD key on either the
handset or base unit.
2. The red line LED will slowly blink, indicating the call is
on hold.
3. If a conference call is active, pressing HOLD will place all
connections on hold.
To Remove a Call From Hold:
1. Press the line key of the call on hold, or the HOLD key
again. This will remove the call from hold, making the call
active again.
2. The red line LED will return to steady illumination,
indicating the line is active.
3. During a conference call, to remove both lines from hold,
press the CONF key.
To Change Phones After Placing a Call on Hold:
1. Place the call on hold as above.
2. Pick up the call at another telephone that is on the same
line. The telephone will activate the line and remove the 		
hold at the original telephone.
To Mute the Speakerphone
1. Press the MUTE key on the base unit. The red LED above
the MUTE key will illuminate. The party on the other end
will not be able to hear you when the MUTE LED is lit.
2. Press the MUTE key again to turn off the mute feature.
The MUTE LED will go out.
Converting From Desk to Wall Mount
The AC8200/AC9200 series can be adapted for wall mounting
applications. The conversion is easiest to make when the
handset and cords are not connected.
1. Located on the handset cradle, above the speaker grill,
is the wall/desk mount clip. Remove this clip by firmly
pushing it upward towards the top of the phone.
2. Flip the clip over (top to bottom) so that the protruding 		
edge is towards the top of the phone and replace it in 			
its slot.This edge will hold the handset when the phone
is mounted on the wall.
3. Turn the telephone over so the bottom is up, facing you.
Place it on a non-abrasive surface to prevent scratching.
4. Locate and remove the mounting bracket. Firmly push back
and pull up to remove two of the four retaining tabs.
5. Rotate the mounting bracket 180º degrees clockwise, so
that the mounting eyelet on the bracket is facing in the 			
same direction as the other mounting eyelet located on the
bottom of the telephone.
6. Insert the top two retaining tabs of the mounting brackets
into the mounting bracket slots (located near the middle
of the telephone). Then firmly push down to insert
the retaining tabs on the opposite side of the
mounting bracket.
7. Connect a 15-foot RJ-45 cord into the LINE jack on the back
of the phone.
8. Turn the telephone over, and slide the telephone down 			
onto the mounting posts of the wall bracket. Ensure
that both eyelets line up with the mounting posts.
The Ringer Equivalence Number (REN) of this device is 0.7B.
Notice: The Ringer Equivalence Number (REN) assigned to each
terminal device provides an indication of the maximum number of
terminals allowed to be connected to a telephone interface. The
termination on an interface may consist of any combination of
devices subject only to the requirement that the sum of the Ringer
Equivalence Numbers of all the devices does not exceed 5. This
telephone connects to the telephone network under the connecting
arrangement code CA11A.
IMPORTANT SAFETY INSTRUCTIONS
WHEN USING YOUR TELEPHONE EQUIPMENT, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE
THE RISK OF FIRE, ELECTRIC SHOCK AND INJURY TO PERSONS,
INCLUDING THE FOLLOWING:
1. READ AND UNDERSTAND ALL INSTRUCTIONS.
2. FOLLOW ALL WARNINGS AND INSTRUCTIONS MARKED
ON THE PRODUCT.
3. UNPLUG THE PRODUCT FROM THE WALL OUTLET BEFORE
CLEANING. DO NOT USE LIQUID CLEANER OR AEROSOL CLEANERS.
USE A DAMP CLOTH FOR CLEANING.
4. DO NOT USE THIS PRODUCT NEAR WATER, FOR EXAMPLE, NEAR
A BATHTUB, WASH BOWL, KITCHEN SINK OR LAUNDRY TUB, IN A
WET BASEMENT, OR NEAR A SWIMMING POOL.
5. DO NOT PLACE THIS PRODUCT ON AN UNSTABLE CART, STAND OR
TABLE. THE PRODUCT MAY FALL, CAUSING SERIOUS DAMAGE TO
THE PRODUCT.
6. SLOTS AND OPENINGS IN THE CABINET AND THE BACK OF
BOTTOM ARE PROVIDED FOR VENTILATION, TO PROTECT IT FROM
OVERHEATING. THESE OPENINGS MUST NOT BE BLOCKED OR
COVERED. THE OPENINGS SHOULD NEVER BE BLOCKED BY
PLACING THE PRODUCT ON THE BED, SOFA, RUG OR ANY OTHER
SIMILAR SURFACE. THIS PRODUCT SHOULD NEVER BE PLACED 			
NEAR OR OVER A RADIATOR OR HEAT REGISTER. THIS PRODUCT
SHOULD NOT BE PLACED IN A BUILT-IN INSTALLATION UNLESS 			
PROPER VENTILATION IS PROVIDED.
7. NEVER PUSH OBJECTS OF ANY KIND INTO THIS PRODUC
THROUGH CABINET SLOTS AS THEY MAY TOUCH DANGEROUS 			
VOLTAGE POINTS OR SHORT OUT PARTS THAT COULD RESULT
IN A RISK OF FIRE OR ELECTRIC SHOCK. NEVER SPILL LIQUID OF 			
ANY KIND ON THE PRODUCT.
8. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT DISASSEMBLE
THIS PRODUCT. BUT TAKE IT TO A QUALIFIED SERVICE FACILITY IF
SERVICE OR REPAIR WORK IS REQUIRED. OPENING OR REMOVING
COVERS MAY EXPOSE YOU TO DANGEROUS VOLTAGES OR OTHER
RISKS. INCORRECT REASSEMBLY CAN CAUSE ELECTRIC SHOCK 			
WHEN THE APPLIANCE IS SUBSEQUENTLY USED.
9. UNPLUG THIS PRODUCT FROM THE WALL OUTLET AND REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL UNDER THE
FOLLOWING CONDITIONS:
-		WHEN THE POWER SUPPLY CORD OR PLUG IS DAMAGED
			OR FRAYED.
-		IF LIQUID HAS BEEN SPILLED INTO THE PRODUCT.
-		IF THE PRODUCT HAS BEEN EXPOSED TO RAIN OR WATER.
-		IF THE PRODUCT DOES NOT OPERATE NORMALLY BY
			FOLLOWING THE OPERATING INSTRUCTIONS. ADJUST ONLY 			
			THOSE CONTROLS THAT ARE COVERED BY THE OPERATING
			INSTRUCTIONS, AS IMPROPER ADJUSTMENT OF OTHER
			CONTROLS MAY RESULT IN DAMAGE,AND MAY REQUIRE
FCC Interference Information
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not cause
harmful interference; and (2) This device must accept any interference
received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna for the radio or television
that is receiving the interference).
- Reorient or relocate and increase the separation between the
telecommunications equipment and receiving antenna.
- Connect the telecommunications equipment into an outlet on a
circuit different from that to which the receiving antenna is connected.
FCC RF Radiation Exposure Statement
The installation of the base unit should allow at least 20 centimeters
between the base and persons to be in compliance with FCC RF
exposure guidelines. For body-worn operation, the portable part
(handset) has been tested and meets FCC RF exposure guidelines.
This device must not be co-located or operating in conjunction with
any other antenna or transmitter. The changes or modifications not
expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Contacting Teledex
Worldwide Headquarters
6311 San Ignacio Ave
San Jose, CA 95119
Telephone
Main: +1.408.363.3100
Toll Free (US) +1.800.794.8353
Fax: +1.408.363.3136
Internet
www.teledex.com
Part Number 600.0480.71
Email
sales@teledex.com
Copyright © 2007 Teledex, LLC. ALL RIGHTS RESERVED. Specifications and information contained herein may change without notice. For the latest information,
please visit www.teledex.com.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Encryption                      : Standard V2.3 (128-bit)
User Access                     : Print
Create Date                     : 2007:09:12 13:01:50-07:00
Creator                         : Adobe InDesign CS2 (4.0.5)
Modify Date                     : 2007:09:13 10:31:14+08:00
Tagged PDF                      : Yes
Producer                        : Adobe PDF Library 7.0
Trapped                         : False
Creation Date                   : 2007:09:12 13:01:50-07:00
Mod Date                        : 2007:09:13 10:31:14+08:00
Metadata Date                   : 2007:09:13 10:31:14+08:00
Creator Tool                    : Adobe InDesign CS2 (4.0.5)
Thumbnail Format                : JPEG
Thumbnail Width                 : 256
Thumbnail Height                : 256
Thumbnail Image                 : (Binary data 2177 bytes, use -b option to extract)
Instance ID                     : uuid:3ca5e010-616b-11dc-88cd-0016cb92b9bd
Document ID                     : adobe:docid:indd:5bfb4704-56e4-11dc-a9c7-de3dde70be42
Rendition Class                 : proof:pdf
Derived From Instance ID        : 5bfb4703-56e4-11dc-a9c7-de3dde70be42
Derived From Document ID        : adobe:docid:indd:3d357b15-5624-11dc-9e3b-b0394b953837
Manifest Link Form              : ReferenceStream, ReferenceStream, ReferenceStream
Manifest Placed X Resolution    : 72.00, 72.00, 300.00
Manifest Placed Y Resolution    : 72.00, 72.00, 300.00
Manifest Placed Resolution Unit : Inches, Inches, Inches
Manifest Reference Instance ID  : uuid:2C04730C56ED11DC9B9AFDD197A9E2AE, uuid:2C04730C56ED11DC9B9AFDD197A9E2AE, uuid:3FA6E3844CB411DCB7B9D51058FDEE45
Manifest Reference Document ID  : uuid:2C04730B56ED11DC9B9AFDD197A9E2AE, uuid:2C04730B56ED11DC9B9AFDD197A9E2AE, uuid:8AE9EE491B6411DCAD35BD68425F7BBD
Format                          : application/pdf
Has XFA                         : No
Page Count                      : 4

EXIF Metadata provided by EXIF.tools