Teledyne 401 O3 Calibrator Users Manual

2015-02-03

• SAFETY MESSAGES
• TABLE OF CONTENTS
• LIST OF FIGURES
• LIST OF TABLES
• INTRODUCTION
  • Preface
  • Warranty
  • Principle Of Operation
    • Interferent Rejection
  • Specifications
    • Noise (PPB RMS)
    • Lower Detectable Limit (LDL) PPB
    • Zero Drift (PPB)
    • Span Drift
    • Linearity
    • Lag Time
    • Rise And Fall Times
    • Temperature Range
    • Humidity Range
    • Flow Rates
    • Power
    • Weight
  • Installation And Overview
  • Electrical And Pneumatic Connections
    • Electrical Connections
    • RS-232
    • Pneumatic System
    • Exhaust Connections (See Figure 1-5)
    • Output Flow Adjustment
  • Operation Verification
    • Final Test And Calibration Values
  • Options
    • Rack Mount With Slides
    • Status Outputs
• OPERATION
  • Key Features
    • O3 Readout
    • O3 Analog Output
    • E2 ROM Backup Of Software Configuration
    • Adaptive Filter
    • Data Acquisition
    • RS-232 Interface
    • Password Protection
  • Front Panel
    • Front Panel Display
    • Programmable Pushbuttons
    • Status LEDs
• CALIBRATION
  • Manual Zero Air Supply
  • Manual O3 Generation
  • Automatic Zero/Span (or Multipoint) Check
  • Manual Zero/Span (or Multi-Point) Check
  • Summary Of Front Panel Calibration Controls
  • Photometer Calibration
  • Remote Zero/Span Check (Contact Closure)
  • Remote Zero/Span Check Or Adjustment (RS-232)
  • Hold Off
• SETUP MODE
  • Setup Mode Operation
  • Setting Automatic Multipoint (ASEQ) Check
  • Setting Automatic Zero/Span Duration
  • Examining The Ozone Formula Slope And Offset
  • Setting the O3 Generation Mode
    • BNCH Mode
    • REF Mode
    • CNST Mode
  • Setting The Time-Of-Day
  • Setting The Date
  • Adjusting The Clock Speed
  • Setting The O3 Concentration Range
  • Setting The Analog Output Offset
  • Setting The RS-232 Baud Rate
  • Setting The Analyzer I.D.
  • Disabling The Calibration Password
  • Setting The Fault LED Timeout
  • Software Configuration
  • Summary Of Setup Variables
• DIAGNOSTICS
  • Test Measurements
  • Diagnostic Tests
    • D/A Output
• HANDLING WARNINGS
• RS-232 COMMUNICATIONS
  • DAS Reporting
  • Warnings
  • Status/Control
  • Diagnostics
  • Test Measurements
  • Viewing And Modifying Variables
• ADJUSTMENTS
  • Power Supply Board Adjustment
    • Box Temperature Limits
  • A/D - D/A Calibration Procedure
  • Output Voltage Range Changes
  • Flow Readout Adjustment
  • DC Power Supply
  • CPU
  • Status Lines
  • UV Lamp Power Supply Adjustment
  • Ozone Generator Lamp Setup
  • Ozone Generator Calibration
  • Dark Current Signal Adjust Procedure
  • Bench Feedback Option
• TROUBLESHOOTING
  • Overview
  • Troubleshooting Fundamental Calibrator Operation
    • Checking The Power Sub-Systems
    • Checking The CPU And Display
    • Checking The Keyboard
  • Troubleshooting Using Warning Messages
  • Troubleshooting Using Test Function Values
  • Troubleshooting Dynamic Problems
    • Noisy Or Unstable Readings At Zero
    • Noisy, Unstable, Or Non-Linear Span Readings
    • Slow Response To Changes In Concentration
    • Analog Outputs Do Not Agree With Front Panel Readings
    • Cannot Zero
    • Cannot Span
  • Troubleshooting Individual Sub-Assemblies And Components
    • Troubleshooting Flow Problems
    • Troubleshooting Temperature Problems
    • Checking The V/F Card
    • Checking The DC Power Supply Board
    • Checking The Pneumatic Sensor Board
    • Checking The Source Lamp And Detector
    • Checking Main Switching Valve
    • Checking The Lamp Power Supply
  • Warranty/Repair Questionnaire
• ROUTINE MAINTENANCE
  • Maintenance Schedule
  • Leak Checking
  • Cleaning Of Sample Cell
  • Changing The Prom
• MODEL 401 SPARE PARTS AND EXPENDABLES KITS
  • Spare Parts For CE Mark Units
  • Spare Parts For Non-CE Mark Units
    • LIST OF AVAILABLE MODEL 401 OPTIONS
      • RECOMMENDED ZERO AIR SYSTEM
        • REFERENCES
          • SOFTWARE MENU TREES
            • ELECTRICAL SCHEMATIC INDEX