Teltronic U PTMDT500760C MDT-500-2 mobile terminal User Manual MDT 500 2 Mobile Radio User Guide

Teltronic S.A.U. MDT-500-2 mobile terminal MDT 500 2 Mobile Radio User Guide

Users guide

User GuideMDT-500-2 Mobile Radio
Original Instructions: ENGLISHDocument Number: MOD-16-2125Issue 1.1Copyright© PowerTrunk, Inc. 2002–2017. All rights reserved.No part of the information contained herein and the other referred documents may be copied, distributed or transmitted byany means to any other party without prior written permission of Teltronic S.A.U. and/or PowerTrunk Inc. The distributionof this document may be also covered by NDA (non-disclosure agreement) between Teltronic S.A.U. and/or PowerTrunkInc. and the receiver.Please also note that part of these contents even may be covered by patent rights.This document, the referred documents and the described product are considered protected by copyright according to theapplicable laws.PowerTrunk and the PowerTrunk logo are registered trademarks of Teltronic S.A.U.DisclaimerAlthough every reasonable effort has been made to ensure the accuracy of the information contained herein and any otherreferred document, this should not be construed as a commitment on the part of Teltronic S.A.U. and/or PowerTrunk Inc.,and the liability of Teltronic S.A.U. and/or PowerTrunk Inc. for any errors and omissions shall be limited to the correctionof such errors and omissions. Teltronic S.A.U. and/or PowerTrunk Inc. welcomes any comment as a way to improve anydelivered documentation. The information contained herein has been prepared for the use of appropriately trainedpersonnel, and it is intended for the purpose of the agreement under which the information is submitted. Any party using orrelying upon this information assumes full responsibility for such use and in no event shall Teltronic S.A.U. and/orPowerTrunk Inc. be liable to anyone for especial, collateral, incidental, or consequential damages in connection with orarising out of the use of this information. The information or statements given in these documents regarding the suitability,capacity or performance of the mentioned hardware or software products cannot be considered binding but shall be definedin the agreement made between Teltronic S.A.U. and/or PowerTrunk Inc. and the customer. Teltronic S.A.U. and/orPowerTrunk Inc. reserves the right to revise these documents and to make changes to its content at any time, without priornotification.Software license agreementNOTICE: CAREFULLY READ THE LEGAL AGREEMENT CORRESPONDING TO THE LICENSE YOU PURCHASED,WHICH SETS FORTH THE GENERAL TERMS AND CONDITIONS FOR THE USE OF THE LICENSED SOFTWARE.Contact DetailsPowerTrunk, Inc.66 York Street Jersey CityNJ 07302U.S.A.T: +1 201 630 4520F: +1 201 630 45222MDT-500-2 – 01/2017
CONTENTSSafety 4Compliance 6MDT-500-2 connections 9Unpacking 10Additional equipment 11Console options and accessories 12Console accessories 12Internal back-up battery 13Connection with the MDT-500-2 mobile radio 14Console and Application Interface Unit 14Mobile radio audio control 15Customisation 16User Guide 3
SafetyREAD THETETRA PRODUCT SAFETY GUIDE SUPPLIED WITH THEPRODUCT FOR IMPORTANT INFORMATION ABOUT SAFELYOPERATING THIS PRODUCT.ALWAYSPOWEROFF the mobile radio in environments where RF wirelessdevices could potentially cause an explosion. Potentially hazardous areas arenot always signed. Obey all signs and instructions relating to the usage of RFwireless devices.ONLYfit an approved accessory. If a non-approved acccessory is fitted, itmay compromise the product safety ratings and may void any productwarranty.DONOT attempt to dismantle this product. Servicing and repairs to thisproduct must be performed by trained service technicians at PowerTrunkapproved service centres.Important safety notes about the antennaOnly use PowerTrunk approved antennas with this product. PowerTrunkTETRA radios have been tested and certified for European, FCC and IC safetyand compliance regulations using the following antennas:Model Antenna (part no.)MDT-500-2 9525-800-41021The use of non-approved antennas may damage the product, will result inthe non-compliance with regulatory requirements, compromise the productsafety ratings, reduce the length of operating time and will invalidate theproduct warranty.NEVER touch the antenna when your radio is transmitting, this may cause aminor burn to the skin and may affect the operational range of the antenna.DO NOT handle, hold or swing your radio by its antenna, this may damageyour radio and the antenna.NEVER use your radio if the antenna shows signs for damage.4MDT-500-2 – 01/2017
NEVER use your radio without an antenna attached, unless your radio isbeing used with an external antenna (such as an RSM antenna).Transmitting without an antenna may damage your radio.The antenna should be installed and operated with a minimum distance of52cm from any person.Exposure to RF energyPowerTrunk designs and manufactures products to meet strict guidelines andinternational standards relating to Radio Frequency (RF) energy and thepotential health risks associated with using RF wireless devices. If you haveany concerns relating to long term health risks associated with using RFwireless devices, you should obtain advice from your employer.OperationIt is the responsibility of the person operating the product to ensure that it isoperated safely at all times, and that local laws and regulations governing theusage of Radio Frequency (RF) wireless devices are observed. Obey all signsand instructions relating to the usage to RF wireless devices.User Guide 5
ComplianceFederal Communication Commission (FCC) RegulationsPowerTrunk Inc. TETRA radios generate, use and radiate RF energy and, ifnot installed and used in accordance with the instruction manual, may causeharmful interference to radio communications. Radios that comply with thelimits for a Class A digital device, pursuant of part 15 of the FCC rules, areidentified by an FCC certification ID label (located under the battery).Operation is subject to the following two conditions: (1) This device may notcause harmful interference, and (2) this device must accept any interferencereceived, including interference that may cause undesired operation. Theselimits are designed to provide reasonable protection against harmfulinterference when the equipment is operated in a commercial environment.Operation of this equipment in a residential area is likely to cause harmfulinterference in which case the user will be required to correct the interferenceat their own expense. Changes or modifications not expressly approved bythe party responsible for compliance could void the user's authority tooperate the equipment.The device may contain functions that are not operational in U.S Territoriesexcept as noted in the certification filing. The TCB Grant may have extendedfrequencies as noted in the certification filing and Section 2.927(b) may applyto the authorisation. The device complies with 47 CFR Part 90.203 (e), in thatthe operator cannot directly program the transmit frequencies using thenormal accessible external controls. All instructions detailed in this manualmust be followed in order to ensure compliance with SAR and RF exposurelimits.Failure to observe these restrictions may result in exceeding the FCC RFexposure limits.Disposing of waste batteriesPowerTrunk Inc. radios are supplied with a rechargeable battery. This symbolon the battery and its packaging indicates that it must not be disposed of withhousehold or commercial waste. Please dispose of your waste batteriesaccording to your national and local regulations. Contact your service6MDT-500-2 – 01/2017
provider or PowerTrunk Inc. for information about recycling batteries in yourregion of the world.Waste Electrical and Electronic Equipment disposal informationThis symbol on the product or its packaging indicates that this product mustnot be disposed of as household or commercial waste. Some countries haveset up collection and recycling systems for waste electrical and electronicproducts. By ensuring that this product is disposed of correctly, you will helpprevent potentially negative consequences for the environment and humanhealth, and help conserve natural resources. Please dispose of your wasteproduct according to your national and local regulations. Contact yourservice provider or PowerTrunk Inc. for information about disposing of thisproduct in your region of the worldUS and Canada MarketsPowerTrunk radios may be restricted in frequency by the relevant IC FCB orFCC TCB Grant. Refer to the Grant for allowed frequency ranges.PowerTrunk MDT-500-2 mobile radios are approved Class A digital apparatusthat comply with Canadian ICES-003.FCC radiation exposure statementThis radio is intended for use in occupational/controlled applications whereusers have been made aware of the potential risks for exposure and canexercise control over their exposure. This product is not authorised forgeneral population, consumer or similar use. This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.The antenna should be installed and operated with a minimum distance of52cm from any person.IC RSS warningThe term “IC:” before the certification/registration number only signifies thatthe Industry Canada technical specifications were met. Nominal antenna portimpedance is 50 Ω.IC radiation exposure statementThis radio is intended for use in occupational/controlled applications whereusers have been made aware of the potential risks for exposure and canexercise control over their exposure. This product is not authorised forUser Guide 7
general population, consumer or similar use. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.Full details of RF exposure and compliance can be found athttp://www.ic.gc.ca.Compliance product labellingThe following compliance product labelling apples to the MDT-500-2 mobileradio:Product Compliance product labellingMDT-500-2 CAN ICES-3 (A)/NMB-3(A)MDT-500-2This device complies with Part 15 of the FCC Rules.Operation is subject to the condition that this device doesnot cause harmful interference.MDT-500-2This radio is restricted to occupational use only tosatisfy FCC RF energy exposure limits. Read theuser guide for awareness and control information.8MDT-500-2 – 01/2017
MDT-500-2 connectionsAll connections are on the rear panel.12345Item Connection1 Antenna2 Power/Audio cable3 Accessory - colour console or handset-based console4 GPS antenna (optional)5 Accessory - colour console or handset-based console (optional)Your mobile radio may not have a GPS antenna fitted.User Guide 9
UnpackingUnpack the container(s) and ensure that all items specified on any deliverynote are present and received in good condition. If any of the goods aredamaged or not supplied, contact your service provider or PowerTrunkInc.within 10 days of receipt of equipment.The MDT-500-2 is supplied as follows:MDT-500-2 mobile radioMounting bracketCables (including fuses) for installationProduct Safety GuideSCC3/HBC3 Quick Reference GuideInstallation GuideNote: If the MDT-500-2 mobile radio is supplied in bulk shipments (5mobile radios per box), the cables and mounting brackets are supplied inseparate boxes.Note: The accessory pack must be specified at time of ordering.Always keep the documentation supplied with the product for futurereference. Ensure that any user documentation provided with the product iskept safe and accessible by any person who is responsible for operating theproduct.10 MDT-500-2 – 01/2017
Additional equipmentYour mobile radio requires the connection of additional equipment.The MDT-500-2 can accommodate upto two audio/data devices such as acolour console and/or a hand-based console, with additional audio equipmentconnected through the colour console.Part no. Description300-01808 Sepura Colour Console 3 (SCC3) Latin300-01913 MDT-500-2 programming cable9525-800-41021 AntennaXXX-XXXXX Hand-based Console 3 (HBC3) LatinXXX-XXXXX Application interface boxUser Guide 11
Console options andaccessoriesThere are many options available for the installation of the mobile radio. Thetransceiver can accommodate up to 2 remote consoles, for example a colourconsole and a handset-based console, with additional accessories such as a fistmicrophone or handset connected through the colour console. Anycombination of consoles can be fitted.The mobile radio is designed to be installed within a vehicle, on a motorcycleor as a standalone unit within an office environment using a Desk MountUnit (DMU).There are a number of vehicle, motorcycle and desktop accessories that canbe attached to the colour console. Contact PowerTrunk for more informationabout accessories available.Console accessoriesThe colour console can accommodate a number of audio accessories such as afist microphone or handset. The following accessories are available forconnection to the colour console:Part No. Description300-00061 Handset (PTT and hook switch)300-00062 Fist Microphone300-00074 Desk Microphone with PTT300-00075 Headset (no PTT)300-00076 Footswitch PTT12 MDT-500-2 – 01/2017
Internal back-up batteryThe MDT-500-2mobile radio has a small rechargeable internal back-up battery.This battery powers the internal Real Time Clock in the event that the mainpower to the product is removed.The battery may have discharged during the manufacturing process or if theproduct has been in storage for some time. When the product is connected toits main supply, the back-up battery will charge regardless of whether theproduct is powered on or not. The charge period for a full charge may be upto 48 hours.User Guide 13
Connection with the MDT-500-2 mobile radioYour MDT-500-2 mobile radio works with colour consoles and hand-basedconsoles, with the optional provision of the Applications Interface Unit (AIU).Console and Application Interface UnitThe MDT-500-2 mobile radio supports the connection of up to two consoles,either a Colour Console or a Handset-based Console (via an Interface andHandsfree box), or an Applications Interface Unit, which is similar to aconsole but does not have a keypad and display. Through the use of aconsole, the MDT-500-2 mobile radio can support the connection of up to 6 ofthe following audio accessories:The MDT-500-2 mobile radio supports Colour Console connection (SCC3).SCC3 allows you to connect two of the following audio accessories at thesame time:a hands-free kita fist microphonea handset audio accessorybuilt-in handsetup to one hands-free kitIf two users are using the same mobile radio, operational procedures arerequired to ensure that the actions of the two users do not conflict.On some configurations it is possible to have a hands-free kit attached to eachconsole. If this is the case, only one of the remote microphones is live duringa call. The remote microphone which is live is the one attached to the consolewhich accepted or made the call or switched the call to hands-free.14 MDT-500-2 – 01/2017
Mobile radio audio controlThe mobile radio supports the concept of a single controlling audio accessoryfor a call. The controlling audio accessory is the one in control of the call, andthe only one on which the microphone becomes active.Tip: When a fist microphone or hands-free kit is used, the received audiois directed to the loudspeaker connected to the mobile unit. When ahandset is used, the received audio is directed to the handset earpiece.The controlling audio accessory is normally the Remote Microphone used inconjunction with the loudspeaker, i.e. the hands-free kit or ‘Public’ mode. Tomake a different accessory become the controlling accessory, press the PTTbutton on that accessory or by take it off hook. If the new controllingaccessory has an earpiece then normally this is used for received audioinstead of the Loudspeaker (‘Private’ mode).When in ‘Private’ mode you can switch to ‘Public’ mode by pressing thehands free soft key (if configured). Taking a handset off hook, or using itsPTT will return to ‘Private’ mode.While the controlling accessory is not the Remote Microphone, you mayswitch to another accessory by pressing the PTT button on that accessory.Taking that accessory off-hook does not change the controlling accessory.This allows a second user to listen to received audio on another accessory.If the controlling accessory is placed on-hook this clears the call unlesscustomised differently. Other accessories can be put back on-hook withoutclearing the call in progress.All earpiece audio is left on all the time in order that multiple users may listento the received audio.User Guide 15
CustomisationThe MDT-500-2 is programmed using Radio Manager. To program the mobileradio you will need the appropriate software loaded onto a PC and aprogramming cable.The two main areas that may need adjusting are the audio levels and themicrophone gain. If any changes are made to the default settings listed, it isnecessary to re-program the mobile radio. #Periodically, you will need to reprogram your MDT-500-2 mobile radio withsoftware updates.The levels of receive speech volume, alert tone volume and microphone gainscan be adjusted to suit the installation environment. The parameter referencenumber is provided to help identification when using Radio Manager.Speech and alert volumeThe following parameters can be found under the ‘PROFILE’ template.Parameter name Index DefaultMinimum Speech Level 8000 -45dBMaximum Speech level 8010 0dBMinimum Alert Volume 8020 -39dBMaximum Alert Volume 8030 0dBMicrophone gain settingsThe following parameters can be found under the ‘PRODUCT’ template.Parameter name Index DefaultDesk Microphone gain 7155 30dBHeadset Microphone Gain 7230 30dBVehicle Adaptor Fist Microphone gain setting 7145 30dBVehicle Adaptor Microphone gain setting 7150 30dB16 MDT-500-2 – 01/2017
PowerTrunk, Inc.66 York Street Jersey CityNJ 07302U.S.A.T: +1 201 630 4520F: +1 201 630 4522 powertrunk.com

Navigation menu