Texas Instruments 110LEM900 The CC110LEM-868-915 is a development tool for TIs sub 1 GHz CC110L chip. User Manual

Texas Instruments Inc. The CC110LEM-868-915 is a development tool for TIs sub 1 GHz CC110L chip. EVALUATION BOARD KIT MODULE EVM ADDITIONAL TERMS

a href="https://usermanual.wiki/Texas-Instruments" itemprop="url"> Texas Instruments >

Users Manual

SWRU292B October 2013   Web sites:  www.ti.com/lprf E2E Forum:  www.ti.com/lprf-forum Make sure to subscribe to the Low-Power RF Newsletter to receive information about updates to documentation, new product releases, and more. Sign up on the TI web pages.   CC11xL 868/915 MHz Development Kit Quick Start Guide  Opening the Box and Running the Packet Error Rate Test  1. Kit Contents   2 x SmartRF™ Transciever EB (TrxEB) 2 x CC110LEM 868/915 MHz 1 x CC113LEM 868/915 MHz 1 x CC115LEM 868/915 MHz 1 x MSP430 Debug Probe (FET) 2 x Micro USB Cables 1 x Standard USB Cable 1 x 14-pin Flat Cable  The 868/915 MHz RF boards in this kit are FCC and IC certified and tested to comply with ETSI/R&TTE over temperatures from 0 to +35°C.  FCC/IC Regulatory Compliance FCC Part 15 Class A Compliant IC ICES-003 Class A Compliant  (* picture may deviate) 2. TrxEB Overview           Caution! The kit contains ESD sensitive components.  Handle  with  care  to prevent permanent damage.  3. Plug the EM into the TrxEB    Insert  a  CC110LEM  into  the  TrxEB.  Do  not  use excessive force on the EM.   The EM has a PCB antenna, so there is no need for an external antenna.  You can also use CC113L and CC115L for the Per test, but  note that CC113L  is a  receiver only and CC115L is a transmitter only.   4. Select Board Mode  Use the switches S1 and S2 to select the operating mode of the board. For the sake of this quick start guide,  please  select  “Enable”  and  “UART”.  This configuration will make it possible to communicate directly with the MSP430 over a  virtual COM  port on the PC.      5. Power Options  There  are  several  ways  of  applying  power  to  the TrxEB.    2 x 1.5V AA Non-Rechargeable Alkaline Batteries   USB (5V through USB plug)   External Power Supply (requirements below)   MSP430 Debugger  When  the  power  source  is  batteries  or  USB,  the voltage  regulators  on  the  TrxEB  will  set  the  on-board supply voltage to 3.3VDC.  External Power Supply1 Requirements: Nom Voltage: 3.3VDC Max Current: 800 mA Efficiency Level V  Warning!  To  minimize  risk  of  personal  injury  or property  damage,  never  use  rechargeable batteries to power the board. 6. Select Power Source    Depending  on  the  power  source,  make  sure  you connect  jumpers  to  the  appropriate  pins  on  the “Power  Source”  header.  For  instance,  if  you  use batteries, use a jumper to short-circuit pin 1 and 2 on the header. The last jumper in the row (pin  9-10)  should  always  be  mounted,  unless  the MSP430 FET is used as the power source.  Note  that  there  should  only  be  one  active power source at any one time. Do not leave the board powered when unattended. 7. Welcome Screen    Turn  on  power  with  the  Main  Power  switch.  You should now see the Texas Instruments logo and a short  description  of  the  buttons  on  the  LCD. Pushing  any  of  the  five buttons  on  the  board  will take you to the main menu.  NB!  If  you  don’t  see  anything  on  the  screen make sure the mode switches are in the correct positions (see step 4 above). 8. Packet Error Rate Test    Select  the  PER  (Packet  Error  Rate)  test  by highlighting  the  selection  using  the  up/down buttons. Confirm  your selection by  pressing Enter (right button). 9. Select Test Mode    The PER  test can  be run is several modes. Easy Mode  sets  up  a  one-way  test  and  uses  default settings. This test is convenient for practical range testing.   The other test modes are described in the “TrxEB RF PER Test Software Example  User’s  Guide”, available on the kit web page.  To proceed, highlight “Easy Mode” and press Enter (right button).                                       1 When using an external power supply, make sure it meets the listed requirements in addition to complying with applicable regional product regulatory and safety certification requirements such as UL, CSA, VDE, CCC, and PSE.  EM Connectors MSP430 Breakout USB EM Breakout Main Power Switch Power Selection Board Mode Switches LCD Buttons LEDs MSP430 Debug Interface
Download:
Mirror Download [FCC.gov]
Document ID2131570
Application ID1LeCGy3qAdvziIx7fIdWkA==
Document DescriptionUsers Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize113.87kB (1423409 bits)
Date Submitted2013-12-02 00:00:00
Date Available2013-12-02 00:00:00
Creation Date2013-10-28 17:20:53
Producing SoftwareMicrosoft® Word 2010
Document Lastmod2013-10-28 17:20:53
Document TitleEVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Document CreatorMicrosoft® Word 2010
Document Author: Magnus Wines
FCC ID Filing: ZAT110LEM900

Navigation menu