Texas Instruments ZLIGHT2 The Zlight2 is a development tool for TIs 2.4 GHz CC2531 IEEE802.15.4 System-on-Chip with USB. User Manual Zlight2 Quick Start Guide
Texas Instruments Inc. The Zlight2 is a development tool for TIs 2.4 GHz CC2531 IEEE802.15.4 System-on-Chip with USB. Zlight2 Quick Start Guide
Users Manual
SWRUXXX
Feb 2013
Web sites: www.ti.com/lprf
E2E Forum: www.ti.com/lprf-forum
Make sure to subscribe to the Low-Power RF
Newsletter to receive information about updates to
documentation, new product releases, and more.
Sign up on the TI web pages.
Zlight2 Quick Start Guide
Opening the box and adding the light to a ZLL network
1. Kit Contents
• 1 x Zlight2 LED light
• Documentation
The Zlight2 is
FCC and IC certified and
tested/complies with ETSI/R&TTE
over
temperature from 0 to +35°C. The antenna is
an on-board half wave dipole PCB antenna.
Caution! The kit contains
ESD
sensitive components. Handle with
care to prevent permanent damage.
2. Hardware Requirements
To run the example described in this Quick Start
Guide, you need a USB power supply capable of
supplying at least 800mA and max 5.5V, a type
A to micro-USB cable to connect it to the light,
and a ZigBee Light Link (ZLL) remote control.
3. Powering the board
Connect the Zlight2 board to the USB power supply
through the type A to micro-USB cable (not
included).
Caution! To minimize risk of injury, avoid touching
components during operation if symbolized as hot.
Do not leave the EVM powered when
unattended.
4. Touch linking
Touch link the Zlight2 lamp by holding the
remote control close to the top of the lamp
and following the instructions provided with
the ZLL remote control
5. Operating the Zlight2
Once connected to the ZLL network through
touch linking, the Zlight2 can be controlled by
the remote control unit. Please follow the remote
control user guide.
Caution! To minimize the risk of
fire or equipment damage, make
sure that air is allowed to
circulate freely around the
Zlight2 board when operating.
Avoid touching components during operation if
symbolized as hot.
Additional Tools and Links
CC debugger
The CC debugger is a tool that allows you to flash
and debug the Zlight2 using SmartRF Flash
Programmer or IAR Embedded Workbench. It
connects to a USB port on your PC and to the
debug header on the Zlight2 board.
SmartRF Flash Programmer
Texas Instruments has a simple tool which can
be used to program and flash the Zlight2.
SmartRF Flash Programmer can be
downloaded from www.ti.com/tool/flash-
programmer
IAR Embedded Workbench
To develop software, program, and debug the
Zlight2, you should use IAR Embedded
Workbench for 8051.
More information on IAR EW8051, including a
free evaluation version download, can be found at
www.iar.com/ew8051.
Useful Links
Useful Links
CC2531 User’s Guide:
http://www.ti.com/lit/ug/swru191c/swru191c.pdf
For additional help, visit the TI E2E Forums:
www.ti.com/lprf-forum
EVALUATION BOARD/KIT/MODULE (EVM) ADDITIONAL TERMS
Texas Instruments (TI) provides the enclosed Evaluation Board/Kit/Module (EVM) under the following conditions:
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from
all claims arising from the handling or use of the goods.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within
30 days from the date of delivery for a full refund. THE FOREGOING LIMITED WARRANTY IS THE EXCLUSIVE WARRANTY
MADE BY SELLER TO BUYER AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY,
INCLUDING ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE. EXCEPT TO THE
EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
Please read the User's Guide and, specifically, the Warnings and Restrictions notice in the User's Guide prior to handling the
product. This notice contains important safety information about temperatures and voltages. For additional information on TI's
environmental and/or safety programs, please visit www.ti.com/esh or contact TI.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine,
process, or combination in which such TI products or services might be or are used. TI currently deals with a variety of customers
for products, and therefore our arrangement with the user is not exclusive. TI assumes no liability for applications assistance,
customer product design, software performance, or infringement of patents or services described herein.
REGULATORY COMPLIANCE INFORMATION
As noted in the EVM User’s Guide and/or EVM itself, this EVM and/or accompanying hardware may or may not be subject to the
Federal Communications Commission (FCC) and Industry Canada (IC) rules.
For EVMs
not
subject to the above rules, this evaluation board/kit/module is intended for use for ENGINEERING
DEVELOPMENT, DEMONSTRATION OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end
product fit for general consumer use. It generates, uses, and can radiate radio frequency energy and has not been tested for
compliance with the limits of computing devices pursuant to part 15 of FCC or ICES-003 rules, which are designed to
provide reasonable protection against radio frequency interference. Operation of the equipment may cause interference with
radio communications, in which case the user at his own expense will be required to take whatever measures may be
required to correct this interference.
General Statement for EVMs including a radio
User Power/Frequency Use Obligations
: This radio is intended for development/professional use only in legally allocated
frequency and power limits. Any use of radio frequencies and/or power availability of this EVM and its development
application(s) must comply with local laws governing radio spectrum allocation and power limits for this evaluation module. It is
the user’s sole responsibility to only operate this radio in legally acceptable frequency space and within legally mandated power
limitations. Any exceptions to this are strictly prohibited and unauthorized by Texas Instruments unless user has obtained
appropriate experimental/development licenses from local regulatory authorities, which is responsibility of user including its
acceptable authorization.
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant
Caution
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void
the user's authority to operate the equipment.
FCC Interference Statement for Class B EVM devices
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
For EVMs annotated as IC – INDUSTRY CANADA Compliant
This Class B digital apparatus complies with Canadian ICES-003.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Concerning EVMs including radio transmitters
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Concerning EVMs including detachable antennas
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or
lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the
antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that
necessary for successful communication.
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed in the user guide with the
maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in
this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.
~
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Les changements ou les modifications pas expressément approuvés par la partie responsable de la conformité ont pu vider
l’autorité de l'utilisateur pour actionner l'équipement.
Concernant les EVMs avec appareils radio
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance
isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication
satisfaisante.
Le présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation
de l'émetteur.
【
Important Notice for Users of this Product in Japan
】
This development kit is NOT certified as Confirming to Technical Regulations of Radio Law of Japan
If you use this product in Japan, you are required by Radio Law of Japan to follow the instructions below with respect to this
product:
1. Use this product in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
2. Use this product only after you obtained the license of Test Radio Station as provided in Radio Law of Japan with respect
to this product, or
3. Use of this product only after you obtained the Technical Regulations Conformity Certification as provided in Radio Law
of Japan with respect to this product. Also, please do not transfer this product, unless you give the same notice above
to the transferee. Please note that if you could not follow the instructions above, you will be subject to penalties of
Radio Law of Japan.
Texas Instruments Japan Limited
(address) 24-1, Nishi-Shinjuku 6 chome, Shinjuku-ku, Tokyo, Japan
http://www.tij.co.jp
【ご使用にあたっての注意】
本開発キットは技術基準適合証明を受けておりません。
本製品のご使用に際しては、電波法遵守のため、以下のいずれかの措置を取っていただく必要がありますのでご注意ください。
( 1 ) 電波法施行規則第 6条第 1項第 1号に基づく平成 18 年3月28 日総務省告示第 173 号で定められた電波暗室等の試験設備
でご使用いただく。
( 2 ) 実験局の免許を取得後ご使用いただく。
( 3 ) 技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。
日本テキサス・インスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
http://www.tij.co.jp
EVALUATION BOARD/KIT/MODULE (EVM)
WARNINGS, RESTRICTIONS AND DISCLAIMERS
For Feasibility Evaluation Only, in Laboratory/Development Environments. Unless otherwise indicated, this EVM is not a
finished electrical equipment and not intended for consumer use. It is intended solely for use for preliminary feasibility
evaluation in laboratory/development environments by technically qualified electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems and subsystems. It should
not be used as all or part of a finished end product.
Your Sole Responsibility and Risk. You acknowledge, represent and agree that:
1. You have unique knowledge concerning Federal, State and local regulatory requirements (including but not limited to Food
and Drug Administration regulations, if applicable) which relate to your products and which relate to your use (and/or that
of your employees, affiliates, contractors or designees) of the EVM for evaluation, testing and other purposes.
2. You have full and exclusive responsibility to assure the safety and compliance of your products with all such laws and other
applicable regulatory requirements, and also to assure the safety of any activities to be conducted by you and/or your
employees, affiliates, contractors or designees, using the EVM. Further, you are responsible to assure that any
interfaces (electronic and/or mechanical) between the EVM and any human body are designed with suitable isolation
and means to safely limit accessible leakage currents to minimize the risk of electrical shock hazard.
3. You will employ reasonable safeguards to ensure that your use of the EVM will not result in any property damage,
injury or death, even if the EVM should fail to perform as described or expected.
4. You will take care of proper disposal and recycling of the EVM’s electronic components and packing materials.
Certain Instructions. It is important to operate this EVM within TI’s recommended specifications and environmental
considerations per the user guidelines. Exceeding the specified EVM ratings (including but not limited to input and output
voltage, current, power, and environmental ranges) may cause property damage, personal injury or death. If there are
questions concerning these ratings please contact a TI field representative prior to connecting interface electronics including
input power and intended loads. Any loads applied outside of the specified output range may result in unintended and/or
inaccurate operation and/or possible permanent damage to the EVM and/or interface electronics. Please consult the EVM
User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification, please contact
a TI field representative. During normal operation, some circuit components may have case temperatures greater than 60°C as
long as the input and output are maintained at a normal ambient operating temperature. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors which can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during
normal operation, please be aware that these devices may be very warm to the touch. As with all electronic evaluation tools,
only qualified personnel knowledgeable in electronic measurement and diagnostics normally found in development
environments should use these EVMs.
Agreement to Defend, Indemnify and Hold Harmless. You agree to defend, indemnify and hold TI, its licensors and their
representatives harmless from and against any and all claims, damages, losses, expenses, costs and liabilities (collectively,
"Claims") arising out of or in connection with any use of the EVM that is not in accordance with the terms of the agreement.
This obligation shall apply whether Claims arise under law of tort or contract or any other legal theory, and even if the EVM
fails to perform as described or expected.
Safety-Critical or Life-Critical Applications. If you intend to evaluate the components for possible use in safety critical
applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal
injury or death, such as devices which are classified as FDA Class III or similar classification, then you must specifically notify
TI of such intent and enter into a separate Assurance and Indemnity Agreement.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated