Texecom LAHA5002 LAHA5002 Ricochet Digital Transmission Module - External Antenna 920 MHz User Manual

Texecom Limited LAHA5002 Ricochet Digital Transmission Module - External Antenna 920 MHz

User Manual

Installation GuideDigital Transmitter ModuleRicochet® High Power NodeLAHA5001 - Integrated antennaLAHA5002 - External antennaINS733Installation•  Install the unit and battery holder (if required) inside the host unit using appropriate xings.•  Connect the required inputs from the host unit using either the 10 way connector or the input pin connections.•  For the DTMA, the antenna should be connected and positioned away from metal obstacles and the SMA connection must be secured with shrink wrap sleaving or epoxy glue. •  To congure the device, insert the AA batteries whilst holding down the test switch.  The LED display will ash showing the type of unit currently congured.•  Using the test button, select the number for the unit which the module has been installed in and then hold the button down to select.   The unit will now attempt to learn to a Premier Elite 32XPH-W.  •  The above selection will be retained when changing the battery.  To re-congure the unit, repeat the above step.  If changing the device number, the device will need re-learning.•  When not changing the conguration, the learn process is initiated by inserting the battery into Wire Loom ConnectorBattery ConnectorTest DisplayTest SwitchIntegrated AntennaTest DisplayTest SwitchInput Pin ConnectionsConnector for External AntennaMounting PointsDigital Transmitter Module with Integrated Antenna (DTM)Digital Transmitter Module with External Antenna (DTMA)
SpecicationsMin  Nominal MaxSupply Voltage 2.5V 3.0V 3.6VCurrent Draw 100uA 350mAOperating Frequency 920MHz 925MHzPower Output 250mWMax External Antenna Gain 2.0dBiTestingTo test the wireless link from the DTM back to the Premier Elite 32XPH-W, install the module and press the test button. The display will alternate top and bottom segments while it attempts to communicate with the Premier Elite 32XPH-W.  If it is successful, it will display the signal strengths (1-9) for each hop.  If it is unsuccessful, it will display an “F”.Examples:Display ashes 7, -, - DTM has direct connection with the Premier Elite 32XPH-W, of strength 7.Display ashes 8, 7, - DTM is connected to the Premier Elite 32XPH-W through 1 other device.  The strength of the signal between the DTM and the forwarding device is 8, and between the forwarding device and Premier Elite 32XPH-W is 7.Display ashes 5, 8, 3 DTM is connected to the Premier Elite 32XPH-W through 2 other devices.  The strength of the signal between the DTM and the rst device is 5, between the rst device and the second device is 8, and between the second device and Premier Elite 32XPH-W is 3.Display ashes F DTM has no connection to the Premier Elite 32XPH-W.When assembling a system, DTMs should be placed and tested in order working outwards from the Premier Elite 32XPH-W.Note:  Devices are unable to communicate when they are less than 10m apart.Device Safety•  Do not expose any of the inputs or the power supply to voltages above 3.6V.•  Do not install the unit outside unless it is inside a detector or weatherproof enclosure.•  Ensure the product and battery holder are securely installed inside host unit.Battery Safety•  Do not throw into a re.•  Do not heat.•  Do not charge.•  Do not short circuit.•  Do not disassemble.•  Replace only with the same or equivalent type.•  Observe local regulations when disposing of batteries.ApprovalsThis product is tested and approved to Federal regulation 47 1A Part 15 Sub Part C as a modular transmitter.DTM : FCC ID: MYJLAHA5001DTMA : FCC ID: MYJLAHA5002The DTMA is ApproveD wiTh The use of The fMAG35153-sM-3K AnTennA AnD ufL To sMA ADApTor. The sMA ADApTor when connecTeD shALL be shrinK wrAppeD or GLueD wiTh epoxy To AvoiD The enD user connecTinG ALTernATive AnTennA Types.Warning: Any Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.When this product is installed within another product and the module labelling is not visible then the Product label must include:-“Contains Transmitter Module FCC ID:MYJLAHA500x”Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. End users must follow the specic operating instructions for satisfying RF exposure compliance. This transmitter must not be  co-located or operating in conjunction with any other antenna or transmitter.The following warning notice must be included in any product installation or user manual that the module is a part of:-“Any Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.” Note: The device should not be used within 20cm of the human body when the RF is enabled. © 2016 Texecom Ltd. www.texe.com  INS733Regulatory informationSupplier: Texecom Ltd, St. Crispin Way, Haslingden, Lancashire, BB4 4PW, UK.Weee Directive: 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info.Warranty: 1 year replacement warrantyFM 35285

Navigation menu