The Genie a Division of Overhead Door 315390R3 GARAGE DOOR REMOTE CONTROL RECEIVER User Manual

The Genie Company a Division of Overhead Door Corporation GARAGE DOOR REMOTE CONTROL RECEIVER

USERS MANUAL

3560935878For 7' 6" Doors.Extension Kit is available for 8' DoorsIncluded Wall Console MUST be installed prior to Operation of this Garage Door Opener.Safe-T-Beam®Safety Reverse System MUST be Installed and the Force Controls MUST be Properly set to close door.This Equipment meets or exceeds all Federal,State and UL325Safety Requirements.Will not operate “twice as fast”on one-piece doors.SAVE THIS MANUAL FORFUTURE REFERENCEHaving Difficulty? Need Help?Please call us:1-800-784-5028 www.overheaddoor.comPlease have Model information ready when calling.Warranty Information . . . . . . . . . . . . . . . . . . . 2Your Documentation Page. . . . . . . . . . . . . . 3Safety Information. . . . . . . . . . . . . . . . . . . . . . 4Safety Features. . . . . . . . . . . . . . . . . . . . . . . . . 4Important Installation Instructions . . . . . . 4Pre-Installation Checklist. . . . . . . . . . . . . . . . 5Adjustments. . . . . . . . . . . . . . . . . . . . . . . . . . . . 9Programming the Remote Control . . . . . 11Installation of Light Bulbs. . . . . . . . . . . . . . 12Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . 13Troubleshooting Guide. . . . . . . . . . . . . . . . 15Wiring Diagram . . . . . . . . . . . . . . . . . . . . . . . 18Parts List and Explosions. . . . . . . . . . . . 19,20Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . 21TABLE OF CONTENTSThe Genuine. The Original.DC POWERED SCREWDRIVE OPENER™4060OPERATION AND MAINTENANCE MANUALCOMPLETE WITH CODEDODGER®REMOTECONTROL AND SERIESIIELECTRONICS
2For Help,call 1-800-784-5028 or visit www.overheaddoor.comTHE OVERHEAD DOOR CORPORATION LIMITED WARRANTYWhat is covered?Any defect in material and product workmanship from personal,normalhousehold use in accordance with the Owner’s Manual.For how long?MODEL 4060L — Lifetime* on motor,and parts.* for as long as you own your home.This warranty is non-transferable.Who gets the warranty?This warranty is limited to the consumer who originally purchased theproduct.Geographic scope:This warranty applies only to units installed and operated within the coun-try where they were purchased.Limitations:IMPLIED WARRANTIES, INCLUDINGTHOSEOF FITNESS FOR A PARTICULARPURPOSEANDMERCHANTABILITY (AN UNWRITTEN WARRANTY THAT THEPRODUCT IS FIT FOR ORDINARY USE),ARE LIMITED TO ONE YEAR FROM THEDATE OF PURCHASE.OVERHEAD DOOR WILL NOT PAY FOR:LOSS OF TIME;INCONVENIENCE;LOSS OF USE OFYOUR OVERHEAD DOOR PRODUCTORPROPERTYDAMAGE CAUSED BY YOUR OVERHEAD DOOR PRODUCT OR ITSFAILURE TO WORK;ANY SPECIAL,INCIDENTAL OR CONSEQUENTIAL DAM-AGES;OR ANY DAMAGES RESULTING FROM MISUSE OR MODIFICATION OFYOUR OVERHEAD DOOR PRODUCT.Some states and provinces do not allow limitations on how long an implied warranty lasts or the exclusion of incidental or consequential damages,sothe above limitations or exclusions may not apply to you.This warranty is the only one we will give on your Overhead Door product,and it sets forth all our responsibilities regarding your Overhead Door prod-uct.Therearenoother express warranties.State and province rights:This warranty givesyou specificlegal rights,andyou may also have other rights which vary from state to state and provinceto province.How to get warranty service:To obtain warranty service for your Overhead Door product,you must pro-vide proof of the date and place of purchase of the product.1. Do-It-Yourself-Service.Call the Overhead Door Consumer Connection toll free at 1.800.354.3643 toSAVE THESE INSTRUCTIONSVisit Our Website at:www.overheaddoor.comPlease note the following information,so it is available if you need to call us.Date Purchased ______________________________Serial Number ______________________________ Operator Model ______________________________Remote Control Model ______________________________Dealer Name ______________________________Dealer Address ______________________________City ______________________________State ______________________________Zip ______________________________speak in person to a trained Overhead Door representative for assistancein diagnosing the problem and arranging to supply you with therequired parts for do-it-yourself repairs.Trained service representativesare available Monday-Friday,8:00 a.m.- 11:00 p.m.,Eastern Time,and onSaturday,10:00 a.m.to 7:00 p.m.,Eastern Time (subject to holidays) Youmay also get the information you need at www.overheaddoor.com.2.Service From Authorized Dealers.You also may obtain warranty service from Overhead Door authorizeddealers by calling the Overhead Door Consumer Connection at1.800.654.3643 or by visiting www.overheaddoor.com before schedulingwarranty service.If warranty service is provided by an authorized dealer,Overhead Door will provide all required parts under warranty at nocharge to you,but the dealers are independent business people and mayrender a bench or service call charge for their services.Overhead Doorwill not reimburse you or otherwise be responsible for those charges.We suggest that you retain your original packing material in the event wechoose to repair or replaqce your Overhead Door Product and requestthat you ship it to us.Be sure to include your name,address,telephonenumber,proof of date and place of purchase and a description of theoperating problem.After repairing or replacing,your Overhead Doorproduct,we will ship it to your home at no cost to you for parts and labor,but you will have to pay a minimum of $5.00 for shipping and handlingcharges.Your choice of either one of the above-described service options is your exclusive remedy under this warranty.What this warranty does not cover:This warranty does not cover batteries (which are considered replaceableparts),installation,commercial use,defects resulting from accidents,dam-age while in transit to our service location or damage resulting from alter-ations,misuse or abuse,lack of proper maintenance, unauthorized repair ormodification of the product,affixing of any attachment not provided withthe product, programming of the Remote Control Devices,Safe-T-Beam®adjustment/cleaning,staples through wiring,pinched or broken wires,Carriage disengaged,Force Control adjustments, door out of balance, bro-ken springs or cables,power outages,use of extension cords,missing ordamaged parts on discounted,clearanced,final sale or taped cartons,phantom operations (labor is not covered if Opener is functioning proper-ly while technician is in garage),fire,flood,or acts of God,or other failure tofollow the Owner’s Manual.FOR ANSWERS:CALL 1.800.354.3643NOTEPlease keep original or photocopy of your salesreceipt with this manual for future referenceshould service ever be required./ /Figure 17 Model and Serial NumbersModelNumberSerialNumber
For Help,call 1-800-784-5028 or visit www.overheaddoor.com 3YOUR OVERHEAD DOOR GARAGE DOOR OPENER DOCUMENTATION PACKAGEThe documentation provided with your opener has been carefully designed and organized to make the assembly,operation,and continuedmaintenance of your product as easy and safe as possible.This material consists of two main items.Operation and Maintenance ManualWhile it is recommended that all documents be retained for future reference,this manual should contain most of the information that youwill need over the lifetime of your product.The manual is designed in a “flip-flop”configuration with the english version in one half of thebook and the spanish / french version in the other half.The basic contents of this manual are:·Warranty Information·Pre Installation Checklist to be reviewed prior to any assembly or installation·Necessary Adjustments·Programming Remote Devices·Maintenance and Troubleshooting·Parts Explosions·Accessory Order Form·Door Opener Association Safety and Maintenance Brochure (DASMA)·Entrapment Warning Label - To be Adhered in close proximity to wall controlAssembly and Installation PosterThis poster is intended to give a convenient lay flat media to be used at the site of assembly and installation.Color coding is used to makesteps and other information as clear as possible.This poster is Tri-Lingual with english instructions highlighted with a blue background.The basic contents of this Poster are:·Quick Reference Poster·Pictorial and step by step opener assembly instructions·Pictorial and step by step opener installation instructionsIT IS CRITICAL THAT ALL SAFETY WARNINGS THAT ARE MARKED CLEARLY INBOTH THE MANUAL AND POSTER ARE READ,UNDERSTOOD AND FOLLOWED.The Overhead Door Corporation is constantly striving to improve our products and the documentation that comes with them.If youhave any suggestions or ideas for improving this product and it’s documentation,please forward them to:The Overhead Door Corp.22790 Lake Park Blvd.Alliance, Ohio 44601-3498Tri-LingualEntrapment labelEnglish LanguageVersion Spanish / FrenchLanguage VersionSpanish / FrenchLanguage DASMAEnglish LanguageDASMAQuick ReferenceDiagramOpener AssemblyOpener Installation
4For Help,call 1-800-784-5028 or visit www.overheaddoor.comOVERVIEW OF POTENTIAL HAZARDSOverhead doors are large,heavy objects that move with the help of springs under high tension and electric motors. Since moving objects,springs undertension,and electric motors can cause injuries, your safety and the safety of others depend on you reading the information in this manual. If you havequestions or do not understand the information presented, call The Overhead Door Corp. or your local Overhead Door Distributor.POTENTIAL HAZARDEFFECT PREVENTION• Keep people clear of opening while door is moving.• Do Not allow children to play with the door operator.• Do Not operate a door that jams or one that has a broken spring.MOVING DOORWARNING:Could result in deathor serious injury.• Turn off power before removing operator cover.• When replacing cover,make sure wires are not pinched or near moving parts.• Operator must be properly grounded.ELECTRICAL SHOCK• Do Not try to remove,repair or adjust springs or anything to which door spring parts are fastened,such as,wood blocks,steel brackets,cables or other like items.• Repairs and adjustments must be made by a trained doorsystem technician using proper tools and instructions.HIGH SPRING TENSIONSafe-T-Beam®(STB) Non-Contact Reversing SystemPlaces an invisible beam across door opening,that reversesthe door during down travel to the fully open position ifanything passes through beam.Safe-T-Reverse®Contact Reversing SystemAutomatically stops and reverses a closing door within 2seconds of contact with an object.Safe-T-Stop®Timed Reversed SystemAutomatically opens a closing door,if door does not closewithin 30 seconds.ForceGuard®ControlUsed to set the force required for opening and closingdoor.For maximum safety,set the minimum force requiredto fully open and close door.Automatic Lighting SystemLight bulb up to 100 Watts max.,used for safer entries andexits.The light turns on when door is activated and auto-matically turns off 4.5 minutes later.Manual Emergency ReleaseAllows the garage door to be opened or closed manuallyfor emergencies or maintenance.IMPORTANT INSTALLATIONINSTRUCTIONS1READ AND FOLLOW ALL SAFETY,INSTALLATION AND OPERATION INSTRUCTIONS.If you have any questions or do not understand an instruction,call your Factory Authorized installation professional.2Do Notinstall operator on an improperly balanced door. An improperly balanced door could cause severe injury. Repairs and adjustments to cables,spring assembly,and other hardware must be made by a trained service person using proper tools and instructions.3Remove all ropes,and disable all locks connected to the door before installing operator.4Install door operator 7 feet or more above the floor.Mount the emergency release knob 6 feet above the floor.5Do Notconnect the operator to the source of power until instructed to do so.6Locate the control button:• Within sight of door.• At a minimum height of 5 feet,so small children cannot reach it.• Away from all moving parts of the door.7Install the entrapment WARNING label next to the wall button or console.Install the emergency release tag on,or next to,the emergency release8The operator must reverse when the door contacts a 1-1/2 inch high object on the floor at the center of the doorway.This is about the size of a 2" x 4" board laid flat.TO REDUCE THE RISK OF SEVERE INJURY OR DEATH:WARNING:SAFETY INFORMATIONSAFETY FEATURESWARNING:Could result in deathor serious injury.WARNING:Could result in deathor serious injury.In this section,and those that follow,the words Danger,Warning and Caution are used to emphasize important safety information. The word:indicates an imminently hazardous situation which,if not avoided,will result in death or serious injury.indicates a potentially hazardous situation which,if not avoided,could result in death or serious injury.indicates a potentially hazardous situation which,if not avoided,may result in injury or property damage.The word NOTE is used to indicate important steps to be followed or important considerations.DANGER:CAUTION:WARNING:
5For Help,call 1-800-784-5028 or visit www.overheaddoor.comPRE-INSTALLATION CHECKLISTThis Opener includes parts and supplies needed to install in most garages and connect to most garage doors. There are many variations of garages and garage doors. A few additional parts and supplies may be needed to install Opener into your garage and connect to your garage door. While checking items listed below,note any additional items you will need.Tools used in this section:•12'+ Tape Measure •Pencil •Ladder •LevelCheck following items before assembling Opener:CHECK DOOR CONDITION ANDTHICKNESSCheck condition of vertical stile in center of door, (Figure 2) and its connectionto door’s top and bottom beams.AIf door frame is nailed together and not a solid connection,door frame must be braced or reinforced before installing Opener.BIf door is “lightweight”(made with frame and skin - not solid),door (including door frame) must be braced or reinforced before installing Opener.CA door opener reinforcement bracket may also be needed to connect garage door to Opener's Door Bracket. This Opener is designed for installation on a properly braced sectional door or solidly bracedone-piece door.DContact your Overhead Door Distributor or dealer of your garage door for any necessary bracing and a door opener reinforcement bracket (if needed) before proceeding.EIf you have a wooden door,measure door’s thickness. (1/4" x 2") Lag Screws are included for installing Door Bracket onto door. If your door is less than 2”thick,brace door or use shorter Door Bracket Lag Screws (1/4" x 1-1/4" – not included)Check Step 1:CHECK GARAGE DOORALIGNMENT,OPERATION,AND BALANCEARaise door,check alignment and see if it moves freely (Figure 1). If door appears out of alignment,binds,or does not move smoothly,contact an Overhead Door Distributor or dealer of your garage door for repairs and adjustments to door mechanism.BRaise door to 3' – 4' above ground and carefully let go. Door should stay stationary. Slight movement is acceptable. More than slight movement means door is out of balance. Contact an Overhead Door Distributoror dealer of your garage door for repairs and adjustments to door mechanism.CCheck door type. Make a note of whether it is asectional or a one-piece door (Figure 2).Check Step 2:WARNING:If your door sticks,binds,or is out of balance,have it adjusted by an OverheadDoor Distributor. Door springs,cables,pulleys,brackets and associated hardwareare under extreme tension and can causeserious injury or death.NOTEThe Powermax Opener is equipped with an Automatic Garage Door BalanceDetection System.See TroubleshootingGuide on page 16.KEEP FEET CLEAR OF DOOR3' - 4'Sectional Door3' - 4'One-Piece DoorFigure 1 Checking door balanceFigure 2 Note Door TypeTorsion SpringsExtension SpringsCenterStileCenter StileHeader Area
6For Help,call 1-800-784-5028 or visit www.overheaddoor.comMEASURE GARAGE DOOR HEIGHTMeasure garage door height (7'-6", 8'-0", or taller) withtape measure.AIf door height is 7'-6" or less,continue with Check Step 4.BIf door height is 8'-0", you need a Rail Extension Kit.(Figure 3) (See Accessories Order Form,page 21).CIf door height is taller than 8'-0",the door opener you purchasedis the wrong version.Contact an Overhead Door Customer Service Representative at 1-800-784-5028.Check Step 3:CHECK DOOR HEADER AREAAFind vertical center line of door and header:•Close door.•Measure door width at top.•Mark a point at center of door and on header directly above door. Draw a center line to connect points.BFind Header Bracket mounting height (Figure 4):(Do not attach Header Bracket).•Raise door,watching top edge of door and stop door when its edge reaches its highest point.•Measure distance (“H”) from top edge of door to floor.– For sectional doors,add 2-1/2" to “H”. Mark a point on center line. Bottom of Header Bracket will beinstalled here.– For one-piece doors,add 6" to “H”. Mark this point oncenter line. Bottom of Header Bracket will be installed here.CCheck wall for a stud or a solid header at your mark:(If checking a finished wall,a stud finder may be helpful).•If location is above Header,a 2" x 6" board must be screwed to studs beside your mark with at least two Lag Screws and Flat Washers (not provided).•Transfer your mark to new mounting board.Check Step 4:NOTEThe header is a heavily reinforced section of the wall justabove the top of the garage door opening.NOTE•For both types of doors:– If the ceiling in your garage is so low that there is not at least a 3" space above the Header Bracketmounting point,contact a Factory Authorized Dealer.•If a door spring is in the way,place the Header Bracket avove the spring.Do Not move the door spring.Rail Extension for8' doorFigure 3 Rail Extension KitFigure 4 Find Highest Point of door travelSECTIONAL DOORONE-PIECE DOORHEADERHEADERWARNING:Door springs are under extremely high tension and should behandled ONLY by a trained professional.
7For Help,call 1-800-784-5028 or visit www.overheaddoor.comCHECK POWER HEADMOUNTING AREACheck ceiling or space above where Opener Power Head will bemounted (Figure 5):AMeasure from garage door center line mark toward rear of garage:•Approximately 10' back if garage has a 7' 6" door.•Approximately 11' back if garage has an 8' 0" door.BFind location of ceiling joist or truss above where Opener Power Head will be and estimate type and quantity of materials needed for your installation (Figure 6).Check Step 5:NOTEMounting Straps are included to attach the Opener to mostgarage ceilings. Garage construction varies widely.Additional mounting straps or angle iron may be needed foryour installation.OPEN BEAM CEILING EXAMPLESCHECK CEILING FOR GROUNDEDPOWER SOURCEACheck that there is a 15 Amp 120 Volt grounded electrical outlet or grounded permanent wiring box (per building code)within 3' of Opener Power Head:•If not,an outlet or wiring box must be installed. Contact a licensed electrician for installation.•If building codes require permanent wiring,Power Head must be partially disassembled to install appropriate wiring in place of Power Cord. See Figure 33-Assemblyand Installation Poster.Check Step 6:NOTEPermanent wiring must be installed by a LicensedElectrician. Not all Overhead Door Distributors are LicensedElectricians. Contact someone who is a Licensed Electrician.CHECK FOR 15 AMP, 120 VOLTGROUNDED OUTLET OR WIRINGBOX WITHIN 3 FEET OF THEPOWER HEAD.10'for 7-1/2' doors11'for 8' doorsDoor Center LineFigure 5 Check Power Head locationMounting Straps Support board addedfor longer spans PerforatedAngle Iron(Angle iron not included)Figure 6Mounting methods for open beam and finished ceilingsFINISHED CEILINGSLocate ceiling joists ortrusses usinga stud finderor similar device.Attach angle iron(not included) tojoists or trussesthrough finish materialusing Lag Screws.WARNING:NEVER use extension cords or portable generators.Extensioncords can overheat causing a fire.Portable generators do nothave an output compatable with PowerMax requirements.
8For Help,call 1-800-784-5028 or visit www.overheaddoor.comCHECK SAFE-T-BEAM® MOUNTING BRACKET LOCATIONCheck for wood garage frame,jamb,or masonry at mounting location(6" above floor) with attachment tabs facing away from garage door(Figure 7).AIf you cannot mount Safe-T-Beam® Mounting Bracket to wood frame:•Concrete screws and concrete anchors (not included) must be used to mount Brackets on masonry with attachment tabs facing away from garage door.•Safe-T-Beam® Mounting Bracket Extensions may be used (not included - available from a Factory Authorized Dealer or through Accessories Order Form on page 21.Check Step 7:RECOMMENDED TOOLSATools (Figure 8):BAdditional tools to make installation easier:•Slotted and phillips screw-driver bits•Stud finder•Sheet-metal cutting snipsCheck Step 8:DREMOVE EXISTING GARAGEDOOR LOCKSCheck that the garage door locks,rope,and T-Handles are removedfrom the garage door before starting the installation.AIf your garage does not have a separate entry door,it is highly recommended to install a Emergency Release Kit (GER-2).Emergency Release Kit lets you open garage door from outside ifthere is a power failure. (Please see Accessories Order Form on page 22.)Check Step 9:Before going further,get any items and toolsneeded for your installationSafe-T-Beam® Sensor Mounting Bracket Extensions (dealer)Garage door opener reinforcement bracket (dealer)Garage door frame reinforcement brackets,screws,bracing or reinforcement kits (dealer)Lag Screws (1-1/4"or 1-1/2" ) for a wood door less than 2" thick (store)Electrical outlet and/or wiring (supplied by a licensed electrician)Powermax Extension Kit (for 8' garage doors) (store)Sufficient angle iron or strapping for hanging Power Head (store)Two 60 Watt light bulbs (130 Volt bulbs recommended)(store)GER-2 Emergency Release Kit for entry during power failure (store)Wood for header,ceiling,and/or door bracing reinforcement (if needed)Masonry fasteners for Safe-T-Beam® Bracket installation,(if needed)Masonry drill bit (if needed)SourceSensorSafe-T-Beam®Mounting BracketTop ofBracket 6"abovefloorFigure 7 Mounting Safe-T-Beam® ComponentsFigure 8 Recommended Tools
9For Help,call 1-800-784-5028 or visit www.overheaddoor.comSET LIMIT SWITCHES ANDFORCE CONTROLSAdjustment 1:ADJUSTMENTS AND MAINTENANCECoarse Setting of Limit SwitchesASetting Close Limit Switch (Figure 9):•Check that Magnetic Carriage Assembly is disengaged.•With garage door fully closed,slide Close Limit Switch until it is aligned with Carriage Assembly Magnet.•Tighten Set Screw.Do Not over-tighten.BSetting Open Limit Switch:•Manually open garage door to full open position.•Slide Open Limit Switch until it is aligned with Carriage Assembly Magnet.•Tighten Set Screw.Do not over-tighten.•Re-engage Magnetic Carriage Assembly.Setting Force Controls and Final Adjustment ofLimit SwitchesAPre-set Force Controls to midpoint between fully counterclockwise and fully clockwise (Figure 10).BAdjust the Close Limit Switch:•Press Wall Console to close garage door.– If door does not close completely,measure distance from bottom of door to floor. Move Limit Switch same amount toward door and try again.– If door reverses after contacting floor,move Limit Switch toward Power Head and try again.– If door reverses before contacting floor,increase Close force and try again.– If door fails to move,check Safe-T-Beam® System.SeeSafe-T-Beam® Troubleshooting Guide on pg.15,and Opener System Self-diagnostic Troubleshooting on pg.16.•Tighten Limit Switch Set Screw.Do not over-tighten (strip) Limit Switch Set Screw.CAdjust Open Limit Switch:•Press Wall Console to open garage door.– If door does not open completely,move Limit Switchtoward Power Head.– If door opens completely,but motor continues to run,move Limit Switch toward door.•Tighten Limit Switch Set Screw. Do not over-tighten (strip) Limit Switch Set Screw.WARNING• The garage door opens rapidly,and can cause serious injury or death.• Keep the path clear.• Position the ladder to the side of the Power Head so it is clear of all moving parts of the Opener and the door.• Set the door Opener to use the minimum force needed to open the door.NOTE•Little effort is required to turn the Force Adjusting Knobs.•If the door stops moving while opening or closing,adjust the Open Force or Close Force Controls slightly clockwise (to slightlyincrease the force) and retry the step.•The Open Force and Close Force Controls are tobe set to the minimum force necessary to ensure the door smoothly opens fully and closes completely.•The garage door will move slowly the first time it runs,until the Opener “learns”the type of door.•Ensure the Magnetic Carriage Assembly is engaged and is between the two Limit Switches before operating the Opener.Close Limit Switch(door fully closed)Carriage (disengaged) MagnetSwitchSwitchMagnetOpen Limit Switch(door fully open)Carriage (disengaged)Figure 9 Setting Limit SwitchesForce ControlsFigure 10 Making Force AdjustmentsSTATUS
10 For Help,call 1-800-784-5028 or visit www.overheaddoor.comDTest Door Opener:•Run door up and down a few times using Wall Console and observe door travel.•Repeat steps above as needed to set Limit Switch positions.EAdjust Open Force to minimum needed:•Place door in closed position using Wall Console.•Gently adjust Open Force fully counterclockwise (minimum force).•Run Opener using Wall Console.•Observe that door runs to Open Limit Switch.– If not,adjust Open Force Control slightly clockwise,close garage door,and open it again.•Repeat steps above until garage door runs smoothly from Close Limit Switch to Open Limit Switch.FAdjust Close Force to minimum needed:•Place door in open position using Wall Console.•Gently adjust Close Force fully counterclockwise (minimum force).•Run Opener using Wall Console.•Observe that door runs to Close Limit Switch.– If not,adjust Close Force Control slightly clockwise,open garage door,and close it again.•Repeat steps above until garage door runs smoothly from Open Limit Switch to Close Limit Switch.AOpen garage door using Wall Console.BLay a 2" x 4" board flat in center of doorway.CClose door using Wall Console.DCheck that door stops and reverses within 2 seconds after it contacts board:• If door does not reverse,decrease Close Force until door reverses.• If door still does not reverse,move Limit Switch toward door.ECheck Safe-T-Beam® System operation:• If beam is blocked,door will not close.NOTE•To protect your new investment,your opener is equipped with a Timer and Cycle Counter which work together to prevent any chance of heat damage to electrical circuits caused by too many cycles in too short a time. If your Opener suddenly stops responding to the Wall Console - Do Not Unplug the Unit - simply wait 10 minutes for the Timer/Cycle Counter to reset itself and try again.(see page 16,Opener Troubleshooting).•Unplugging the unit will prevent the Timer/Cycle Counter from resetting.NOTEThe door must contact the 2" x 4" board before theCarriage activates the Close Limit Switch. If not,readjust the Close Limit Switch.CHSETTING CONTACTREVERSE FUNCTIONAdjustment 2:NOTELimit Switch and Force Adjustments must be completedbefore checking the contact reverse function (Figure 11).2" x 4" boardlaid flatFigure 11 Checking Contact Reverse
11For Help,call 1-800-784-5028 or visit www.overheaddoor.comATo program one Button of a Remote Control (Figure 12):•Locate Learn Button and Learn Indicator Light near Terminal Strip on Power Head (Figure 13).•Press and release Learn Button. Red Learn Indicator Light will blink 2 times per second.•Press Remote Control Button once within 30 seconds.Red Learn Indicator Light will stay lit.•Press Remote Control Button again. Red Learn Indicator Light will go out,indicating that memory is stored.BProgram each additional Remote using step Aabove (up to seven).Remote Control OperationAPress Button on Remote Control. Garage door will move.BPress Button again. Garage door will stop:•The door automatically stops at the end of the open or close cycle.CPress Button again. Garage door will reverse.WARNINGA moving garage door may cause serious injury or death.•Keep people clear of opening while door is moving.•Do not allow children to play with the Remote Controls.If the Safety Reverse does not work properly:•Close the door and disconnect the Opener using the Emergency Release Cord.•Do not use the door Opener,Remote Controls,or Wireless Keypad.•Refer to the door and door Opener Owner’s Manuals before attempting any repairs.NOTE•Each Remote Control must be programmed separately.•The Remote Controls will not cause the door Opener to close the garage door if the Safe-T-Beam® System is malfunctioning.•When programming the Remote Controls,they must be at least 24" from the Antenna Wire.•If the red Learn Indicator Light blinks approximately 4 times per second,programming has stopped. If programming has stopped,repeat the above steps.•Each Button on a 2 or 3 Button Remote Control is for a different Opener. You cannot use more than one Button per Remote,per Opener.•A maximum of seven Remote Controls or Wireless Keypads can be stored into the Receiver at one time. If a Remote Control becomes lost,or if you want to delete a Remote Control or Wireless Keypad,see “To Erase All Receiver Memory.”Learn Code ButtonFigure 13 Learn Code Button and Indicator Light1 Button Compact Remotew/Docking StationFigure 12 Remote Controls3 Button Compact Remotew/Docking StationFrequencySwitchC PROGRAMMING THEREMOTE CONTROLSProgramming 1:ACCESSORIESTo Erase All Remotes from Power Head MemoryAPress and hold Learn Button on Power Head for 10 seconds or until Learn Indicator Light goes out.Memory is erased:•Program Transmitter/Receiver again as needed.To Replace Remote Control BatteryAFOR NON-FLASHLIGHT MODELS•Pop off the back of the transmitter.– Use coin,pen,screwdriver or any similar device.– Replace old Battery with new coin type battery.• Replace back of remote.BFOR FLASHLIGHT MODELS•Slide open battery cover.– Replace old Battery with new AAA battery.• Replace battery cover.Remote Control Operation ContinuedDSome Remote Controls are equipped with a flashlight.Thelogo is the button which operates the light. There is a backlight under the button.When it does not light,it indicates the battery needs replaced.1 Button Remotew/FlashlightFigure 13 Remote Controls3 Button LargeRemotew/Flashlight3 Button Remotew/FlashlightFlashlight Button315 Mhz390 MhzFrequencySwitch315 Mhz390 MhzFrequency Switch
12 For Help,call 1-800-784-5028 or visit www.overheaddoor.comINSTALLATION OF LENS AND BULBAInstall two 60 Watt light bulbs (not included) into Light Sockets (Figure 14):•Rough service,130 Volt bulbs are recommended.BInstall Lens into slots in Motor Cover.Snap Lens Hinges into slots on back of Motor Cover60 Wattsmaximum Push in Latchestoclose LensFigure 14 Install Lens Cover and Light BulbsTransmitter Compliance StatementABOUT DUAL FREQUENCYREMOTE TRANSMITTERSYour garage door opener (GDO) features a uniquedual frequency remote control system for reliableservice in today’s crowded airwaves.Overcrowdedairwaves may intermittently interfere with GDO’sremote control system. The dual frequency featuregreatly reduces the possibility of unwanted interference.The receiver in the GDO’s powerhead can receive signals at 315 AND 390 MHz.The remote is factoryset at 315 MHz. See Figure 12 and 13 on page 11 forfrequency selector switch.Switch your remote control frequency when:•Remote does not have adequate range.•Remote works inconsistently with fresh battery installed - LED feedback lights up when pressing button.•Programming your car’s HomeLink® system.To program a HomeLink® device:(This GDO is HomeLink® compatible.)•Use a small flat screwdriver to switch the frequency selector to 390 MHz.•Follow the HomeLink® instructions in your car owner’s manual.•Reset the remote control frequency to 315 MHz foreveryday use.
13For Help,call 1-800-784-5028 or visit www.overheaddoor.comAMonthly:•Door springs and door hardware:– Oil door rollers,bearings,and hinges using silicone lubricant or light oil.•Balance Door.– Close door.–Release Magnetic Carriage Assembly from Rail Assemblybypulling downonEmergencyRelease Knob.– Raise door manually 3'- 4' and verify that door staysatthatposition.SeeCheck Step2onpage 5.–ReattachMagneticCarriageAssemblytoRail Assembly bypulling the Emergency Release KnobtowardPower Head.–Close door.• Contact Reverse Test.– Perform Adjustment 2 on page 10.NOTEWhen the door is 3' - 4' above the ground,the doorshould stay open. Slight movement is acceptable. Ifthe door moves too much,contact an Overhead DoorDistributor for service or call Customer Service at 1-800-784-5028.WARNINGDo not operate door automatically or manually if springsare broken. Contact an Overhead Door Distributor for service or call Customer Service at 1-800-784-5028.WARNINGIf the door fails to reverse on contact with the board,adjust the Close Force Control as specified in Set LimitSwitches and Force Controls on page 20. If the Openerstill fails,contact an Overhead Door Distributor for service or call Customer Service at 1-800-784-5028.BYearly:•Wipe off old excess lubricant from Drive Screw.•Lubricate Drive Screw with Lubricant (GLU-3)NOTEUse ONLY Lubricant (GLU-3). Other lubricants may dam-age the Opener.FCC AND IC CERTIFIEDAll devices comply with Part 15 of the FCC Rules.Operation is subject to the following two conditions:(1)this device may not cause harmful interference,and (2)this device must accept any interference received,includ-ing interference that may cause undesired operation.GLU-3LubricantSCHEDULED MAINTENANCECAs Needed:•Replace Bulbs.
14 For Help,call 1-800-784-5028 or visit www.overheaddoor.comNOTES
15For Help,call 1-800-784-5028 or visit www.overheaddoor.comWARNINGTO REDUCE THE RISK OF SEVERE INJURY OR DEATH1READ AND FOLLOW ALL INSTRUCTIONS.2Never let children operate or play with the Door Controls. Keep the Remote Control away from children.3Always keep the moving door in sight and away from people and objects until the door is completely closed.NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.4NEVER GO UNDER A STOPPED,PARTIALLY OPEN DOOR.5Test Opener monthly. The door MUST reverse on contact with a 1-1/2" high object (or a 2" x 4" board laid flat) at the center of the doorway on the floor. After adjusting either the Force or the Limit of travel,retest the DoorOpener. Failure to adjust the Opener properly may cause severe injury or death.6When possible use the Emergency Release only when the door is closed. Use caution when using this Release with the door open. Weak or broken springs are capable of increasing the rate of door closure and increasing the risk of severe injury or death.7KEEP GARAGE DOORS PROPERLY BALANCED. See your Garage Door Owner's Manual. An improperly balanced door increases the risk of severe injury or death. Have an Overhead Door Distributormake repairs to cables,spring assemblies,and other hardware.8SAVE THESE INSTRUCTIONS.IMPORTANT SAFETY INSTRUCTIONS WARNINGUse the Wall Console included with Opener. Any other wall console can cause the Opener to operate unexpectedly andthe light to stop working.TROUBLESHOOTING GUIDESafe-T-Beam® System Self-Diagnostic TroubleshootingSource (Red LED) Sensor (Green LED) Possible Problem SolutionON ON Normal operation None requiredOFF OFF • Power Head not powered • Check breakers,fuses,plugs• Wiring from Power Head bad • Check wiring for obvious shortsOFF ON • Wiring to Source missing or bad • Check wiring• Power has been interrupted • Remove power and reapply2 BLINKS,Pause • Beam not aligned • Check Source,Sensor alignment (Repeat) ON • Beam obstructed • Check for obstruction• Sensor defective • Contact Customer Service2 BLINKS,Pause • Wire to Sensor missing or bad • Check wiring (Repeat) OFF • Sensor defective • Contact Customer Service3 BLINKS,Pause • Sensor receiving interference • Determine source of interference (Repeat) ON • Contact Customer Service4 BLINKS,Pause • Source not sending pulses • Contact Customer Service (Repeat) ON • Source defective • Contact Customer Service
16 For Help,call 1-800-784-5028 or visit www.overheaddoor.comOpener System Self-Diagnostic Troubleshooting• See Status Light on Figure 10,page 9 or Figure 13,page 11)You See Problem What to Do Reference1 BLINK, Motor Drive •Reset Opener—unplug (or disconnect power),wait 5 seconds,plug Pause Board back in (reapply power),and activate from Wall Console.(Repeat) InterruptNormal •First Cycle will run at slow speed.operationrestoredIf the problem •Check door condition. NOTE:This Opener is equipped with an See Doorrecurs automatic garage door balance detection system.An improperly Safety Guidebalanced door,damaged or worn counter-balance spring,binding door hardware or rollers may result in a “ONE-BLINK”signal.•Contact Customer Service for further assistance.Operation not •Check door condition. 1.See page 5.restored •Have an Overhead Door Distributor check: 2.See door– Fuse on Motor Drive Board. Safety Guide– Ribbon Cable on Motor Drive Board is properly inserted into Connector on Controller Board.•Contact Customer service for further service.2 BLINKS, Controller •Reset Opener — unplug (or disconnect power),wait 5 seconds,plug Pause Board back in (reapply power),and activate from Wall Console.(Repeat) Interrupt •Have an Overhead Door Distributor check that Ribbon Cable on Motor Board is properly inserted into connector on Controller Board.•Contact Customer Service for further assistance.3 BLINKS,Opener • Do not unplug or disconnect power from Opener.Wait 10 minutes Pause Overheated for internal clock to provide additional cycles.Cycles are restored (Repeat) or at a rate of 5 cycles per 10 minutes of rest.Over-cycled • Contact Customer Service for further assistance.4 BLINKS, Force Settings •Check Force Settings.NOTE:Force Settings are not pre-set at factory.1.See page 9.Pause Incorrect •Check door condition. 2.See Door(Repeat) •Contact Customer service for further assistance. Safety Guide5 BLINKS, Safe-T-Beam® •Check Safe-T-Beam® Self-diagnostic System.NOTE:Safe-T-Beam® See page 15.Pause Malfunction System must be installed and operational to enable door to close.•Contact Customer Service for further assistance.6 BLINKS, Wall Console •Check Wall Console Wiring for shorts,tight Staples,or pinched Wires. See AssemblyPause does not work •Check Wiring Connections at Power Head and Wall Console. and Installation(Repeat) •Contact Customer Service for further assistance. Poster7 BLINKS, Limit Switches •Check Limit Switch Wire connections to Terminals on Power Head. See AssemblyPause not working •Check for shorted or pinched Wires under Limit Switch Brackets. and Installation(Repeat) •Contact Customer Service for further assistance. Poster8 BLINKS, Wall Console •Vacation Locking Switch on Wall Control is in “Lock”mode. See AssemblyPause locked Unlock switch. and Installation(Repeat) •Contact Customer Service for further assistance. PosterNOTE• The status LED Indicator Light is located under the Lens Cover.The Green LED light will turn ON,then OFF whenpower is applied to the Opener.If LED stays ON,have an Overhead Door Distributor check the Controller Board,or call Customer Service at 1-800-784-5028.• If Safe-T-Beam® problems exists,the door can be closed electrically by holding the Wall Console Button down until door is fully closed.• The Remote Controls and Wireless Keypad will not work without a working Safe-T-Beam® System.
17For Help,call 1-800-784-5028 or visit www.overheaddoor.comGeneral Troubleshooting (Always Check the Status LED Light)Problem What To DoOpener does not run 1. Check power source.from Remote Control A. If Opener is connected to an outlet:•Plug a working lamp into outlet used for PowerHead.•If lamp glows,power source and outlet are OK.•If not,check fuse or circuit breaker or non-compatible GFCI.NOTE:A licensed electrician must replace non-compatible GFCI’s.B. If Opener is connected to a wiring box:•Check that fuse is not blown,or circuit breaker is on and not tripped or off.•If still no power,have a licensed electrician check circuit and wiring.2. If Power Source is OK:•Check connections at Power Head Terminals (see Wall ConsoleInstallation,poster),tighten any loose connection.•Checkconnections at Wall Console Terminals, tighten any loose connections.Have an Overhead Door Distributor check the Ribbon Cable between the Controller Board and Motor Drive Board is properly connected to the Circuit Board Connectors or call Customer Service at 1-800-784-5028.Door Opener starts •Check Wires to ensure that they are not cut (Staples can cut insulation and short Wires).for no apparent reason Replace any shorting Staples and shorted Wires.•Was Remote Control lost or stolen? If so,erase all Remote Control codes from Receiver’s memory and reprogram for remaining remote controls. (See Erase All Receiver Memory on page 11).•Ensure that no Buttons are stuck “pushed-in”on Wall Console or any Remote Controls.Door starts down,then•Check Close Limit Switch setting (see Set Limit Switches and Force Controls on page 9).stops before it is Adjust as needed.completely closed•Check for shorted Wires.•Check garage door for binding.Door starts down,then•If a new installation,check Door Arm position.stops and goes back up•Check operation of Contact Reverse function.•Check Safe-T-Beam® System for beam obstruction or misalignment of Lenses.•Check Safe-T-Beam® System diagnostic code.•Check Close Force adjustment (see Set Limit Switches and Force Controls on page 9). Adjust as needed.•Check garage door for binding.Door will only run closed•Check Open Limit Switch for a short circuit and for proper wiring.•Check Open Force adjustment (see Set LimitSwitches and Force Controls on page 9). Adjust as needed.•Check condition of garage door and door spring(s).•WARNING:If you suspect a problem with the garage door hardware or springs,contact an Overhead Door Distributor for service,or contact Customer Service at 1-800-784-5028.Door will only run open•Check Safe-T-Beam® System as detailed in the Safe-T-Beam® System Self-diagnostic Troubleshooting Chart (see Safe-T-Beam® System Self-diagnostic Troubleshooting Section on page 15).•Check Close Limit Switch for a short circuit and for proper wiring.•Check Close Force adjustment (see Set Limit Switches and Force Controls on page 9). Adjust as needed.Lights will not go out•Disconnect Wires connected to Wall Console. (see WallConsole Installation on page 18).Check their condition and either replace or reconnect.•Until a replacement WallConsole can be obtained,disconnect Wall Console and use only Remote Controls or Wireless Keypad to operate Opener.Door starts up,but stops•Check (ensure) that garage door and Opener are in good repair,properly lubricated,and properlybefore it is balanced as detailed in Maintenance Section.completely open•WARNING:If you suspect a problem with the garage door hardware or springs,contact an Overhead Door Distributor for service,or contact Customer Service at 1-800-784-5028.•Check Open Limit Switch for a short circuit and for proper wiring.•Check Open Force adjustment (see Set Limit Switches and Force Controls on page 9). Adjust as needed.Operator runs,but door •Ensure Magnetic Carriage Assembly is engaged to Rail Drive Screw (see Install Magnetic Carriage Assembly does not move onto Rails on poster).•Check Force adjustment (see Set Limit Switches and Force Controls on page 9). Adjust as needed.•Check that all sections of Rail Drive Screw are turning when Motor runs. If not:– Check condition (not cracked,split,or broken) and placement of Coupler. Replace as needed.– Check condition (not cracked,split,or broken) and placement of Collar and Clip. Replace as needed.Wall Console Vacation •Ensure Magnetic Carriage Assembly is in contact with Close Limit Switch.Lock function does •Check when door is fully closed,that Carriage activates Close Limit Switch. If not,adjust position of Close not work Limit Switch (See page 9).
18 For Help,call 1-800-784-5028 or visit www.overheaddoor.comGeneral Troubleshooting (Always Check the Status LED Light)(Continued)Problem What To DoRemote Control has less •Relocate Remote Control inside car.than 25’operating range•Ensure Remote Control is pointing toward garage door when pressing Control Button.•Replace Remote Control Battery (See page 11).•Reposition Opener Antenna Wire.•Do Not attempt to retune Remote Controls or Receiver.Opener works from Wall •Program code for each Remote Control into Receiver memory (See Programming the Remote Control,but not from Control on page 11.Remote Control•Replace Remote Control Battery (See page 11).•Check Safe-T-Beam® System for beam obstruction or misalignment of Lenses.•Check Safe-T-Beam® System for any diagnostic codes. If present,troubleshoot as detailed in Safe-T-Beam® System Self-Diagnostic Troubleshooting Chart (See page 15).Noisy operation•Ensure all fasteners are tightened.•Check that the garage door and Opener are in good repair,properly lubricated,and properly balanced. (See Maintenance page 13).•WARNING:If you suspect a problem with garage door hardware or springs,contact an Overhead Door Distributor for service,or contact Customer Service at 1-800-784-5028.Safe-T-Beam® System•If an operational problem exists,Opener will not run closed.•Check Safe-T-Beam® System for beam obstruction or misalignment of Lenses.•Check Safe-T-Beam® System for any diagnostic codes. If present,troubleshoot as detailed in Safe-T-Beam® System Self-Diagnostic Troubleshooting Chart (See page 15).Door closes,and Opener•Check position of Wall Console Vacation Lock Switch. It must be in UNLOCKED position for Opener to shuts down open door.WARNINGOpening Cover May Result in Electric ShockWIRING DIAGRAM
19For Help,call 1-800-784-5028 or visit www.overheaddoor.comParts List[1]Item Part Name1A Lens1B Top Plate Assembly1C Light Socket (2)1D Motor Assembly1E Cover1G Motor Drive Board 1H Controller Board1K # 10-24 x 3/8”Hex Head1L # 8-32 x 1”Phillips Screw1M # 8-32 x 3/8”Slotted Hex Head Screw1P Power Cord POWER HEAD ASSEMBLY EXPLODED VIEWPOWER HEAD ASSEMBLY PARTS LISTvaries/modelvaries/modelvaries/modelSerial NumberModel NumberItem Part Name QuantityItem Part Name Required1 Power Head Assembly (main carton) 12 1/4"-20 x 13/16" Hex Head Shoulder Bolt (blue bag) 2(yellow shoulder bolt)4 Rail Assembly,3-Piece 14A First Rail Section (main carton) 14B Middle Rail Section (main carton) 14C End Rail Section (main carton) 16 Carriage Stop 18 1/4"-20 Hex Serrated Flange Nut (blue bag) 49 Rail Clamps (blue bag) 410 5/16"-18 x 11/16" Hex Head Shoulder Bolt (blue bag) 811 5/16"-18 Hex Serrated Flange Nut (blue & orange bags) 1212 Magnetic Carriage Assembly (main carton) 113 Collar (blue bag) 314 Retaining Clip (blue bag) 315 Rail Strap (blue bag) 116 1/4"-20 Hex Head Bolt (blue bag) 218 Open Limit Switch Assembly (White)(green bag) 119 Close Limit Switch Assembly (Brown) (green bag) 121 # 8-32 x 1" Hex Head Screw (green bag) 222 Emergency Release Cord (green bag) 124 Emergency Release Knob (green bag) 125 Emergency Release Tag (green bag) 126 Header Bracket (orange bag) 128 Door Bracket (orange bag) 130 1/4" x 2" Lag Screw (orange bag) 831 Straight Door Arm (main carton) 132 Clevis Pin,3/8" x 15/16" (yellow bag) 233 Cotter Pin,.073" dia.(yellow bag) 234 Curved Door Arm (main carton) 135 3/8" x 7/8" Hex Head Bolt (yellow bag) 236 3/8" Hex Serrated Flange Nut (yellow bag) 237* 2-Conductor Wire (main carton) 1 Roll38* Insulated Staple (red bag)approx.3040* Wall Console (main carton) 141* # 6 x 1-1/4" Pan Head Screw (red bag) 242* Entrapment WarningLabel (manual)(main carton) 143* Safe-T-Beam Sensor (Green LED)(main carton) 144* Safe-T-Beam Source (Red LED)(main carton) 145* Safe-T-Beam Bracket (yellow bag) 246 Coupler (blue bag) 147* #10 x11/4" PhillipsHexHeadScrew (yellowbag)48* One Button Remote Control (main carton)49* Three Button Remote Control (main carton)50* Wireless Keypad (main carton)51* Two Button Remote Control (main carton)52* Safety & Maintenance Guide (manual)(main carton) 153 Wire Clip (green bag) 755* 5/16"-18x3/4"HexHeadBolt(orange bag) 356 1/4-20 x 3/4" Self-drilling Screw (orange bag) 357 Mounting Straps (main carton) 2*Denotes items not shown on page 8. These items will be illustratedthroughout the manual as required.varies/model
20 For Help,call 1-800-784-5028 or visit www.overheaddoor.comEXCELERATORHARDWAREEXPLODEDVIEWNOTEOpener will not function unless Safe-T-Beam® System is installed and Force Controls are properly set.DOORDOOR122224313533363432 815 169115267818114132146331056195314668182153212324A1031 3322 232435333634563028324B4C1615261130 819119141353572225
21For Help,call 1-800-784-5028 or visit www.overheaddoor.comNo C.O.D. shipments. Please include check or moneyorder, made payable to The Overhead Door Corp.Do not send cash. Allow 3-4 weeks for delivery.1-800-354-3643. Please have part number and creditcard ready. Mail Order Form to: Operator Division,22790 Lake Park Blvd, Alliance, Ohio 44601.Weaccept Visa or Mastercard on phone orders only.Please add local sales tax if you reside in one of the states listed.California, Connecticut, Florida, Georgia, Illinois, Indiana,Maryland, Massachusetts, Michigan, New Jersey, New York,Ohio, Tennessee, Virginia, WisconsinTOTAL ORDER $SHIPPING & HANDLING $ 5.00STATE SALES TAX $GRAND TOTAL $Pas d’expédition contre remboursement. Veuillez inclure unchèque ou un mandat bancaire, le payable fait à The OverheadDoor Corp.N’envoyez pas d’argent comptant. Accordez de 3à 4 semaines pour la livraison. 1-800-354-3643. Ayez sous lamain le numéro de la pièce et celui de la carte de crédit. Mettreà la poste le arrngement à: Operator Division, 22790 LakePark Blvd, Alliance, Ohio 44601. Nous acceptons les commandes par téléphone avec paiement par carte de créditVisa ou Mastercard.Veuillez indiquer les taxes de vente locales si vous résidez dans l’undes états répertoriés ci-dessous.COMMANDE TOTALE $MANUTENTION ET EXPÉDITION $ 5.00TAXE DE VENTE $TOTAL GLOBAL $No se aceptan pedidos de pago contra entrega (COD).Sírvase incluir su cheque o giro postal, la cuentapagadera hecha a The Overhead Door Corp.No envíedinero en efectivo. Concédanos 3 a 4 semanas para laentrega. 1-800-354-3643. Sírvase tener listos losnúmeros del modelo y de la tarjeta de crédito. Enviarhacer un pedido de mercancia a: Operator Division,22790 Lake Park Blvd, Alliance, Ohio 4460.Aceptamos pedidos telefónicos de Visa o Mastercard.Sírvase agregar el impuesto de ventas local si usted reside enuno de los siguientes estados:TOTAL DEL PEDIDO $FLETE Y MANEJO $ 5.00IMPUESTO DE VENTAS ESTATAL $GRAN TOTAL $Ordering InstructionsLas Instrucciones que OrdenanInstructions CommandantGarage Door Opener Accessories Order FormFormulario de pedido de accesorios para abridores de puertas de garaje Formulaire de commande des accessoires pour ouvre-porte de garageFor additional accessories not shown. visit our website at www.overheaddoor.comPara accesorios adicionalesno mostrada, visite nuestro sitio web en www.overheaddoor.compour les accessoires supplémentaires pas montré, visiter notré site web à www.overheaddoor.com(OCD CTD-1) 1-Button Compact Remote - Allows remote operation of garage door.Comprima el Mando de Distancia - Proporciónar operación remoto de la puerta del garaje.Télécommande compacte - Permettre opération éloign´´de porte de garage.(OCD CTD-3)3-Button Compact Remote - Allows remote operation of 3 garage doors.De 3 botones Comprima el Mando de Distancia - Proporciónar operación remoto de tres las puertas del garaje.3-boutenner la Télécommande compacte - Permettre opération éloign´ trois portes de garage.(OWKPD)Dual Frequency Wireless Keypad - Operates CodeDodger® Garage Door Openers without Remote Control or key.La frecuencia doble teclado numérico radiofónico - Acciona los abridores de puertas de garaje CodeDodger® sin control remoto o llave.Frequency double le clavier numérique sans fil - Actionne les ouvre-porte de garage avec CodeDodger® sans télécommande ni clé.(GLU-3) 3/4 oz.TubesScrew Drive Lubricant - Ensures proper equipment wear protection.3/4 once Lubricante de tornillo accionar - Asegura componente correcto protección por deterioro.La onza 3/4 Lubricant de la vis - Garantir componant exact par systéme défense vers user.(OWB2)Universal Wall Button - Provides additional convenient inside operation of door.Botón de pared universal - Proporciona operación conveniente de la puerta desde el interior.Bouton mural universel - Actionne l’ouvre-porte de l’intérieur du garage.(GPS-5)Perfect Stop®- Ensures perfect parking.Stop Perfecto®- Asegura el estacionamiento perfecto.Butoir Perfect Stop®- Permet de stationner à la perfection dans le garage.(OSXL8)PowerMax Screw Drive Extension Kit - An Extension that increases the travel of the Opener to accommodate an eight foot door.El extensión deslizante de PowerMax Screw Drive - Unaextensiónpara aumentar lacarreradeun abridor,para acomodar unapuertade8 pies (2,43 m).Nécessaire de rallonge du PowerMax Screw Drive - Rallonge de prolongeant la course de l’ouvre-porte pour une porte de 2,4 m (8 pi) de hauteur.(OD8X)SilentLift Extension Kit - An Extension that increases the travel of the Opener to accommodate aneight foot door.Juego de extensión de cadena deslizable - Unaextensiónpara aumentar la longitud de la baranda para acomodar unapuertade8 pies (2,43 m).Nécessaire de prolongement du coulisseau - Rallonge de prolongeant la course de l’ouvre-portepour une porte de 2,4 m (8 pi) de hauteur.(60 WATT) Enhanced/Rough Service Light Bulb - Ensures proper equipment compatability.Bombilla de 60 Vatios - Asegura componente correcto de sistema.Éclairage de 60 WATT - Garantir componant exact par systéme.(GER-2)Emergency Release Kit - Provides access to garage from outside in the event ofan electrical power failure.Juego de pica-porte de pestillo - Permitir entrtada desde por fuera de garaje porque cortede eléctrico.Nécessaires de Déclenchement de secours - Le nécessaire de déclenchement de secours est conçupour vous permettre d’accéder à votre garage depuis l’extérieur en cas de panne de courant et lorsqu’il.STB Adapter Brackets (2) - Used in conjunction with standard STB Brackets.They provide additional clearance and mounting options.El adaptador pone entre paréntesis (2) - Usado en unión con paréntesis uniformes de montar de STB,ellos proporcionan el espacio libre adicional junto con mortar las opciones.Crochets d’adaptateur (2) - Utilisé conjointement avec STB standard monter les crochets,ils fournissent le dégagement supplémentaire avec monter d’options.SHIP ORDER TO:ENVIAR MERCANCIA CON:EXPÉDIER MARCHANDISE POUR:NAME / NOMBRE / NOMADDRESS / DIRECCIÓN / ADRESSECITY / CIUDAD / VILLESTATE / ESTADO / ÉTAT ZIP / CÓDIGO POSTAL / CODE POSTALCalifornia, Connecticut, Florida, Georgia, Illinois, Indiana,Maryland, Massachusetts, Michigan, New Jersey, New York,Ohio, Tennessee, Virginia, WisconsinCalifornia, Connecticut, Florida, Georgia, Illinois, Indiana,Maryland, Massachusetts, Michigan, New Jersey, New York,Ohio, Tennessee, Virginia, WisconsinHow many?¿Quántos?Commentbeaucoup?$36.50$50.00$35.00$50.00$5.00$3.75$4.00$32.00$32.00$2.73$20.00$4.37P/N 35664RP/N 35664SP/N 35669RP/N 35668RP/N 35164RP/N 35670RP/N 34964RP/N 35671RP/N 35672R(OWC-2W)Deluxe Wall Console - Operates Garage Door.Independent light control.Security vacation lock.Consola de lujo de pared - Acciona la puerta del garaje.Control de luz independiente.Cerradura de seguridad para vacaciones.La Console dse luxe de Mur - Actionne la porte de garage.Commande d’éclairage indépendante.Interrupteur de verrouillage de sécurité.P/N 26210A.SP/N 34963R(Prices subject to change without notice)(Valoran el cambio con sujeción a sin nota)(Les prix assujettissent pour changer sans la notification)P/N 34439R.S(OCD F TD-1)1-Button Flashlight Transmitter - Remote Controller with a Flashlight.1 abrocha transmisor de linterna - Director remoto con una linterna.1-boutenner l’émetteur de lampe de poche - Le contrôleur éloigné avec de lampe de poche.$45.00P/N 35665R(OMSWC-2W)Multi-function Wall Console with Motion Sensor - Automatically turns on garage light when you need it.La Consola de la pared de la multi-función con Promueve Sensor - Automáticament vueltas en la luz de garaje cuando usted lo necesita.La Console Multifontions de Mur avec Fait signe le Détecteur - Allume automatiquement la lumière de garage quand vous avez besoin de lui.$39.00P/N 35746R

Navigation menu