The Kroger SZMDLMA1 CC2533 ZigBee Module User Manual 5 SRMANM Module Manual

Download:
Mirror Download [FCC.gov]
Document ID	2184020
Application ID	BIQfV3/GLlU7glKYqnSy9A==
Document Description	Users Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	13.23kB (165376 bits)
Date Submitted	2014-02-05 00:00:00
Date Available	2014-02-11 00:00:00
Creation Date	2013-12-30 18:12:47
Producing Software	GPL Ghostscript 9.04
Document Lastmod	2013-12-30 18:12:47
Document Title	5_SRMANM Module Manual
Document Creator	PDFCreator Version 1.2.3
Document Author:	kunjan.parikh

SRMANM User Guide
SRMANM
(CC2533 ZigBee MODULE)
USER GUIDE
Rev 1.0
Page 1
SRMANM User Guide
Contents
Introduction .............................................................................................................. 4
1.1
Purpose and scope ...................................................................................................... 4
1.2
Revision History ........................................................................................................... 4
Module Application Circuit ........................................................................................ 5
2.1
Sample Application Connections ................................................................................ 5
2.2
Compliance Limits ....................................................................................................... 6
2.3
Module Power Supply ................................................................................................. 6
Antenna Options and PCB Footprint........................................................................... 7
3.1
Footprint Overview ..................................................................................................... 7
3.2
Module Footprint ........................................................................................................ 8
Agency Statements .................................................................................................... 9
4.1
Federal Communication Commission Interference Statement .................................. 9
4.2
ETSI (European Telecommunications Standards Institute) Statement....................... 9
4.3
RF Exposure ................................................................................................................. 9
4.4
End Product Labelling................................................................................................ 10
Contact Detail .......................................................................................................... 11
Rev 1.0
Page 2
SRMANM User Guide
Figures
Figure 1: SRMANM Application Circuit ...................................................................................... 5
Figure 2: Header Board Footprint Overview.............................................................................. 7
Figure 3: SRMANM Module Footprint overview ....................................................................... 8
Tables
Table 1: Compliance Limit .......................................................................................................... 6
Rev 1.0
Page 3
SRMANM User Guide
1 Introduction
1.1 Purpose and scope
The purpose of this document is to provide details regarding the use of CC2533 ZigBee
Module (SRMANM). This document describes the connections between CC2533 Module and
header board. This connection details can be used to mount Module on other Host Board.
1.2 Revision History
Date
25DEC2013
Rev 1.0
Change Description
Revision
Initial release
1.0
Page 4
SRMANM User Guide
2 Module Application Circuit
2.1 Sample Application Connections
Figure 1 shows the circuit connection between SRMANM Module and CC2533 Header
board. Header board provide the power supply to the SRMANM Module and also debug
header for programming the CC2533.
Figure 1: SRMANM Application Circuit
Please refer SRMANM datasheet for module pin description. Based on application
requirements host device can be interfaced with other pins on the module. Please refer TICC2533 user guide for connection/state information of unused pins.
Rev 1.0
Page 5
SRMANM User Guide
2.2 Compliance Limits
Depending on the country where the module is used, proper power level needs to be set to
meet compliance limit to ensure the certification of module.
Table 1 shows the register value configuration for RF Power to meet compliance limit for
ETSI standard.
Table 1: Compliance Limit
Compliance
TX POWER Register value
ETSI
0XF5
Note: The register value used for FCC compliance is maximum value and cannot be
increased by end user. The RF Output Power configuration is not accessible to End User.
2.3 Module Power Supply
The SRMANM Module can operate between 2.7V to 3.6V power level. However, it is
recommended to provide nominal 3.3VDC supply to Module VCC and GND pins. For details
of VCC – GND pins; please refer Module datasheet.
Rev 1.0
Page 6
SRMANM User Guide
3 Antenna Options and PCB Footprint
SRMANM (CC2533 Module) has PCB Inverted F Antenna designed on Board.
3.1 Footprint Overview
Below figure shows the footprint detail of the Header board for SRMANM Module. The
Header Board (or Host Board) Footprint will be designed as per the Module footprint as
mentioned in datasheet.
Figure 2: Header Board Footprint Overview
Rev 1.0
Page 7
SRMANM User Guide
3.2 Module Footprint
Figure 3 shows the Module footprint over the Header board
Figure 3: SRMANM Module Footprint overview
Rev 1.0
Page 8
SRMANM User Guide
4 Agency Statements
4.1 Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates; uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired
operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
4.2 ETSI (European Telecommunications Standards Institute) Statement
This device has been tested and certified for use in the European Union. If this device is used
in a product, the OEM has responsibility to verify compliance of the final product to the EU
standards.
4.3 RF Exposure
This module has been certified for remote and base radio applications and is not intended
to be operated within 20 cm of the body. If the module will be used for portable
applications, the device must undergo SAR testing.
Rev 1.0
Page 9
SRMANM User Guide
Following instruction can be included in Final product user manual.
Instruction: To satisfy FCC RF exposure requirements for mobile transmitting devices, a
separation distance of 20 cm or more should be maintained between the antenna of this
device and persons during operation. To ensure compliance, operations at closer distances
than this are not recommended.”
4.4 End Product Labelling
The SRMANM Module is labelled with its own FCC ID. If the FCC ID Certification Number is
not visible while installed inside another device, then the device should display the label on
it referring the enclosed module. In that case, the final end product must be labelled in a
visible area with the following:
“Contains Transmitter Module FCC ID: PBR-SZMDLMA1”
OR
“Contains FCC ID: PBR-SZMDLMA1”
The OEM should not provide information to the end user regarding installation or removal
of this RF module or change RF related parameters in the user manual of the end product.
The OEM integrator is still responsible for testing their end-product for any additional
compliance requirements required with this module installed (for example, digital device
emissions, PC peripheral requirements, etc.).
Rev 1.0
Page 10
SRMANM User Guide
5 Contact Detail
The Kroger Co.
11450 Groom Road
Blue Ash, OH-45242,
USA
Rev 1.0
Page 11

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 11
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
Producer                        : GPL Ghostscript 9.04
Keywords                        : ()
Modify Date                     : 2013:12:30 18:12:47+05:30
Create Date                     : 2013:12:30 18:12:47+05:30
Creator Tool                    : PDFCreator Version 1.2.3
About                           : 6b75c429-73ab-11e3-0000-04511d0404b.(V..2013-12-30T18:12:47+05:30
Document ID                     : uuid:6b75c429-73ab-11e3-0000-04511d0404b�l�g�c..
Format                          : application/pdf
Title                           : 5_SRMANM Module Manual
Creator                         : kunjan.parikh
Description                     : ()
Author                          : kunjan.parikh
Subject                         : 

EXIF Metadata provided by EXIF.tools