The Sapling HPB-24G-1 2.4GHz FHSS TRANSCEIVER User Manual

The Sapling Company, Inc 2.4GHz FHSS TRANSCEIVER

Contents

User Manual

USER MANUAL May 2013 2.433-2.449 GHz Frequency Hopping Transceiver Module Model: D-CCA-HPB-24G-1 FCC ID: R73HPB-24G-1 REV 2
Page 2 of 7 Introduction This module is only authorized to be installed in fixed mount installation and may not be installed in a mobile or portable device. The HPB-24G-1 module is to be used in Sapling Master Clocks such as the SMA-3000 or SMA Repeater and equivalent models. The module is only to be connected to and installed in other Sapling products. Specifications The antenna gain is +2.15dBi. The maximum output power will be 30 dBm. The transmit cycle is a sequence of 80 data strings on 76 different frequencies, each transmitted for 3 msec. Every transmit cycle is 240 msec in duration (80 x 3ms). The frequency hopping pattern is proprietary to Sapling and covers the range from 2.433 to 2.449 GHz. Connections The picture shows the HPB-24G-1 RF module, connectors, and FCC ID label. HPB-24G-1 P1 FCC ID: R73HPB-24G-1 P2 P1 POWER & DATA P2 PROGRAMMING
Page 3 of 7 HPB-24G-1 Connectors Installed The picture on the next page shows the HPB-24G-1 RF module in a repeater. It shows the SMA-1SR-G0000-1 and the connectors to the rest of the Sapling Wireless Clock System. P1 OPERATING CONNECTOR PIN 1 5 VOLTS PIN 2 GROUND PIN 3 PPS OUT PIN 4 TXD PIN 5 RXD PIN 6 MSTR/SLV PIN 7 STBY PIN 8 NO CONNECTION * PIN 1 IS SQUARE PAD. P2 PROGRAMMING CONNECTOR PIN 1 TDO/TDI PIN 2 3.3 VOLTS PIN 3 TDI PIN 4 3.3 VOLTS PIN 5 TMS PIN 6 NO CONNECTION PIN 7 TCLK PIN 8 TEST PIN 9 GROUND PIN 10 NO CONNECTION PIN 11 RST PIN 12 TXD PIN 13 SHIELD PIN 14 RXD * PIN 1 IS SQUARE PAD. P2 PROGRAMMING P1 POWER & DATA
Page 4 of 7 SMA-1SR-G000-1 P1 OPERATING CONNECTOR PIN 1 5 VOLTS RED WIRE PIN 2 GROUND BLACK WIRE PIN 3 PPS OUT PIN 4 TXD ORANGE WIRE PIN 5 RXD VIOLET WIRE PIN 6 MSTR/SLV WHITE WIRE PIN 7 STBY PIN 8 NO CONNECTION * PIN 1 IS SQUARE PAD. FCC ID: R73HPB-24G-1 P1 P1 POWER & DATA HPB-24G-1 5 VOLT POWER SUPPLY 5 VOLT POWER & DATA BOARD
Page 5 of 7 The picture below shows the top of the SMA-1SR-G000-1 with HPB-24G-1 RF module antenna connector and the FCC ID and the Compliance Label. SMA-1SR-G000-1 SMA-1SR-G000-1 Label The label below is an example of the FCC ID and the Compliance Label.
Page 6 of 7 Installed The picture below shows the HPB-24G-1 RF module in a master clock. It shows the SMA-3S0-G008-1 and the connectors to the rest of the Sapling Wireless Clock System. SMA-3S0-G008-1 The picture below shows the top of the SMA-3S0-G008-1 with HPB-24G-1 RF module antenna connector and the FCC ID and the Compliance Label. SMA-3S0-G008-1 FCC ID: R73HPB-24G-1 HPB-24G-1 P1 P1 OPERATING CONNECTOR PIN 1 5 VOLTS RED WIRE PIN 2 GROUND BLACK WIRE PIN 3 PPS OUT PIN 4 TXD ORANGE WIRE PIN 5 RXD VIOLET WIRE PIN 6 MSTR/SLV WHITE WIRE PIN 7 STBY PIN 8 NO CONNECTION * PIN 1 IS SQUARE PAD. P1 POWER & DATA 5 VOLT POWER SUPPLY RELAY & CONTROL BOARD
Page 7 of 7 SMA-3S0-G008-1 Label The label below is an example of the FCC ID and the Compliance Label. Operation 1. The HPB-24G-1 RF module, as a repeater transceiver, will receive time from another transmitter or clock and re-transmit the time. 2. The HPB-24G-1 RF module, as a master clock transceiver, will transmit the time for 240 msec and receive the time for up to 20 seconds once a minute. FCC Statement: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT. “Changes Or Modifications Not Expressly Approved By The Party Responsible For Compliance Could Void The User's Authority To Operate The Equipment.”

Navigation menu