The Sapling STR001 STR 2000 / STR 1000 User Manual users manual 1

Download:
Mirror Download [FCC.gov]
Document ID	605874
Application ID	EeoGXqMnx59/n1rLi+A+Mw==
Document Description	users manual 1
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	88.7kB (1108803 bits)
Date Submitted	2005-11-25 00:00:00
Date Available	2005-11-23 00:00:00
Creation Date	2005-04-15 11:03:27
Producing Software	Acrobat Distiller 6.0 (Windows)
Document Lastmod	2005-04-15 11:03:27
Document Title	STR 2000 Transceiver Installation Manual 1-12-05.pub
Document Creator	PScript5.dll Version 5.2
Document Author:	Mitch

STR 2000 Series Transceiver Installation Manual
Table of Contents
MOUNTING
Mounting Diagram…………………………………………………………………………
Page 2
WIRING INFORMATION
Wiring Information………………………………………………………………………..
Page 3
INTERFACING
59 Minute Correction.…………………………………………………………………….
Page 4
58 Minute Correction………………………………………………………………………
Page 4
National Time and Rauland……………………………………………………………….
Page 5
Rauland Digital…………………………………………………………………………….
Page 5
Dukane…………………………………………………………………………………….
Page 6
Once A Day Pulse…………………………………………………………………………
Page 6
RS232 and TCP/IP…………………………………………………………………………
Page 7
PROGRAMMABLE RELAY
Programmable Relay Wiring………………………………………..……………………..
Page 8
FREQUENTLY ASKED QUESTIONS
STR 2000 Frequently Asked Questions...…………………………………………………
Page 9
TROUBLESHOOTING
STR 2000 Troubleshooting………………………………………………………………..
Page 10
FOR SYSTEM WIRING DIAGRAMS, PLEASE REFER TO SYSTEM INFORMATION
Page 1
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Mounting Diagram
INSTRUCTIONS
1. Find a location that will allow the Transceiver to transmit the signal in
open space. (hallway recommended)
2. Run the wiring through the knockouts and connect according to the wiring information.
3. Tighten all four (4) screws (6-32) on the front panel.
4. Line up the Transceiver in the desired mounting location and mark the
holes.
5. Mount anchors (not included) to where the holes were marked at in the
previous step.
6. Mount the Transceiver using four (4) screws (not included).
Page 2
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Wiring Information
Page 3
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Interfacing With Other Systems
59 Minute Correction
58 Minute Correction
Page 4
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Interfacing With Other Systems
National Time and Rauland
Rauland Digital
Page 5
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Interfacing With Other Systems
Dukane
Once A Day Pulse
Page 6
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
RS232 Input and Output
RS232 RS232
Ground Output Input
16
17
18
TCP/IP LAN Connection
STR 2000 TCP/IP LAN Connector
TCP/IP LAN Connection To
Internet
Page 7
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Programmable Relay
N.O.
COMMON
N.C.
*For instructions on programming the relay, refer to the STR 2000 Programming Manual.
Page 8
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Frequently Asked Questions
Where is the best location for the Transceiver to be mounted?
Usually, the hallway is the best location because it is mostly open space in typical applications.
How far can the Transceiver transmit the wireless signal?
The Transceiver can transmit up to 1000 meters in open space.
Will the Transceiver have interference from cordless or cellular phones?
No, because with Sapling’s innovative frequency-hopping technology, interference will not occur.
The Transceiver transmits between 915 - 928 MHz and switches frequencies instantly when any interference is present.
Can analog wireless clocks be combined with digital wireless clocks?
Absolutely. The analog and digital wireless clocks are designed to work together, whether the
clocks are running on battery (analog wireless clock only), 24 volts or 110 volts.
Can the GPS receiver correct the Transceiver?
Yes, the GPS receiver can transmit the data via RS485 communication output to the RS485 input on
the Transceiver.
Does the Transceiver interface with a computer?
Yes, through the RS232 connection.
If the power is disconnected from the Transceiver, will I lose all of my settings?
The Transceiver will not lose the settings if power is disconnected from it.
Is the Transceiver FCC compliant?
The Transceiver is FCC approved via FCC part 15, Section 15,247.
My power source is 220 volts. Can the Transceiver be powered on that voltage?
Yes, the Transceiver can work on 110 volts/60 Hz or 220 volts/50 Hz.
Page 9
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
Troubleshooting
The clocks aren’t receiving the signal. What should I do?
Make sure that the Transceiver is in a place where the signal can be transmitted in open space.
I can’t get my Transceiver to synchronize with the Internet. What should I do?
Check your connection between the ends of the CAT 5 cable. Make sure the pin configuration is
correct. Also, make sure the Internet connection is enabled in programming. Refer to the Transceiver Programming Manual for more information.
What should I do if the Transceiver is not powering up?
Measure the voltage between pins 1 & 3. The voltmeter should read 85 - 135 VAC between the hot
and the neutral.
I’m trying to synchronize my GPS with the Transceiver via RS485, but it doesn’t seem to correct. What should I do?
Make sure the RS485 is in the correct polarity. If the polarity is reversed, the Transceiver will not
correct. Also check the LED to make sure it is flickering once a second for communication.
What should I do if I can’t get the programmable relay to close?
Refer to the programming manual of the STR 2000 for instructions on how to program the relay. If
it still does not work, contact Sapling technical support.
There is a large gap between clocks farther in the building where the Transceiver can’t reach.
What should I do for increased signal?
Add a Sapling Repeater, part number STR-100-000-1. This will give you an added 1000 meters of
transmission (in open space).
Page 10
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com
STR 2000 Series Transceiver Installation Manual
FCC Wants You to Know
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable
protection against harmful interference in a commercial installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
a) Reorient or relocate the receiving antenna.
b) Increase the separation between the equipment and receiver.
c) Connect the equipment to an outlet on a circuit different
from which the receiver is connected.
d) Consult the dealer or an experienced radio/TV technician.
FCC WARNING
Modifications not expressly approved by the manufacturer could void the user authority to operate
the equipment under FCC Rules.
Note: For precautionary measures, FCC recommends a distance of 10cm from the clock to constant
human physical exposure.
Sapling, Inc. 1633 Republic Road Huntingdon Valley, PA 19006 Phone: (215) 322-6063 Fax: (215) 322-8498 www.Sapling-Inc.com


---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Page Count                      : 12
XMP Toolkit                     : XMP toolkit 2.9.1-13, framework 1.6
About                           : uuid:9601a618-5227-4e75-b0d8-6ea0d8dc18d0
Producer                        : Acrobat Distiller 6.0 (Windows)
Creator Tool                    : PScript5.dll Version 5.2
Modify Date                     : 2005:04:15 11:03:27-04:00
Create Date                     : 2005:04:15 11:03:27-04:00
Document ID                     : uuid:683c5091-e07b-4d87-b92e-12e0e66057f5
Format                          : application/pdf
Title                           : STR 2000 Transceiver Installation Manual 1-12-05.pub
Creator                         : Mitch
Author                          : Mitch

EXIF Metadata provided by EXIF.tools