The Swan Corporation Bs 1515 Users Manual V01666 #256
BS-2515 to the manual 7467403a-95c7-4294-9ddd-a99ef4241519
2015-02-03
: The-Swan-Corporation The-Swan-Corporation-Bs-1515-Users-Manual-461498 the-swan-corporation-bs-1515-users-manual-461498 the-swan-corporation pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
BAR SINKS BS-1515 TOOLS REQUIRED • Ruler • Drill • Caulk • Saber Saw (if counter top cutout is required) BS-2515 TRACE COMPLETELY AROUND EDGE OF SINK DRAW A 1-1/2ⴖ RADIUS AT EACH CORNER DRILL STARTER HOLE INSIDE OF CUTOUT LINE CUT INSIDE OF LINE 5/16⬙ CUTOUT LINE 1. If it is necessary to cut out the counter top, invert sink and position onto the counter top. Locate sink front to rear and so that the bowl will not interfere with the cabinets below. Trace a pencil line around the outside edge of the sink and remove the sink from the counter top. 2. Measure in 5/16⬙ from the initial sink outline and draw a second line inside the first. Draw a 1-1/2⬙ radius at each corner. This second interior line will be your cutout line. 3. Drill starter hole inside of cutout line. Check Cutout Line Measurements Model Width Depth BS-1515 14-3/8⬙ 14-3/8⬙ BS-2515 24-3/8⬙ 14-3/8⬙ Measure the cutout or the pre-cut opening to be sure it conforms to the sizes listed. OWNER’S MANUAL MODEL NOS. BS-1515 BS-2515 Installation Care and Cleaning CAUTION: Read ALL instructions carefully BEFORE starting your installation. Save this manual for future reference. 4. Using a saber saw, cut inside of cutout line. Trial fit sink to check proper fit. BAR SINKS APPLY CAULK 5. Fixture hole locations are identified with a gray label indicating the most desired placement. Position a chisel on the desired dot and strike with a hammer to break out the hole. Clean out fixture hole with a knife. If hole is not used, peel off the label. Attach faucet, drain, and accessories according to manufacturer’s instructions. 6. Apply a bead of caulk (not included) to the underside of the sink flange and position sink into counter top opening. 7. Attach four (4) sink clips to underside of sink. Sink clips provided will accommodate a counter top up to 1-1/2⬙ thick. Tighten screws in front then rear first. Work from side to side. Do not overtighten. Clean up excess caulk. CLEANING Clean your Swanstone sink as you would any other fine bath fixture, using normal household detergents and cleansers. Just wiping the wall surfaces quickly removes watermarks and residues. Occasional scrubbing with household abrasive cleansers ensures that the original luster is maintained. REPAIRING SOLID COLORS Use 400 grit sandpaper to remove scratches and gouges in the surface. A “scotchbright pad” can be used to blend in the area. AGGREGATE & GALAXY COLORS Use 400 grit sandpaper to remove scratches and gouges in the surface. To blend in the area use a fine grade, white, automotive polishing compound or paste wax. 8. Connect all faucet supply lines, disposal (if available), and drain trap fittings per manufacturer instructions. CHECK FOR LEAKS • Supply user tubes to faucet • Supply riser tubes to shut off valves or lower connections • Fill sink with water and check for leaks around drain • Release water from sink and check for possible leaks • Tighten as needed The Swan Corporation One City Centre St. Louis, MO 63101 (314) 231-8148 Patent Pending Form #256-11-91-10M
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : Yes Create Date : 2002:06:05 18:30:34-05:00 Modify Date : 2002:06:05 18:30:34-05:00 Page Count : 2 Creation Date : 2002:06:05 23:30:34Z Mod Date : 2002:06:05 23:30:34Z Producer : Acrobat Distiller 5.0.5 for Macintosh Author : randy Metadata Date : 2002:06:05 23:30:34Z Creator : randy Title : V01666 #256EXIF Metadata provided by EXIF.tools