The Watt Stopper d b a Qmotion MC433FM2 433 MHz FM Remote Transmitter User Manual

The Watt Stopper, Inc. d/b/a Qmotion 433 MHz FM Remote Transmitter

User Manual

Download: The Watt Stopper d b a Qmotion MC433FM2 433 MHz FM Remote Transmitter User Manual
Mirror Download [FCC.gov]The Watt Stopper d b a Qmotion MC433FM2 433 MHz FM Remote Transmitter User Manual
Document ID3676358
Application ID4vUcYoEWKJLsFHCNWnO3SA==
Document DescriptionUser Manual
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize12.59kB (157423 bits)
Date Submitted2017-12-13 00:00:00
Date Available2017-12-13 00:00:00
Creation Date2017-11-17 14:55:29
Document Lastmod0000-00-00 00:00:00
Document TitleUser Manual

Gen 3 Multi Channel
Single Channel
Programming Instructions
FIRST TIME SETUP
1. TUG the shade 6"—10" to wake the shade trom shipping sleep mode
2. Single Channel Remote - PRESS and HOLD the UP button until the shade travels to the
upper limit position
3. Multi Channel Remote — First select a channel to program: PRESS and RELEASE a
CHANNEL selection (1-6). Next, PRESS and HOLD the UP button until the shade travels to QITIOLIOH"
the upper limit position
SETTING LOWER LIMIT U P
1. PRESS and RELEASE the DOWN button, shade will travel to the current lower limit '
2. PRESS and HOLD the DOWN button until the shade JOGS 25%
3. TUG the shade hembar 6-10" 50% CHANNEL
4. Adjust the shade hembar manually to the new lower limit position
5. PRESS and HOLD the DOWN button until the shade travels to the upper limit position 75%
ADDING A REMOTE OR CHANNEL DOWN
1t PRESS and RELEASE the UP button to send the shade to the upper limit position
or manually roll the shade to the upper limit Multi Channel
2. PRESS and HOLD the UP button until the shade travels to the 75% closed position
3. TUG the shade hembar 6"-10"
4. Single Channel Remote - PRESS and HOLD the UP button until the shade travels to the
upper limit position
5. Multi Channel Remote - First select a channel to program: PRESS and RELEASE a
CHANNEL selection (1-6). Next, PRESS and HOLD the UP button until the shade travels to the
upper limit position
Remote
DELETING A REMOTE OR CHANNEL
1. PRESS and HOLD the UP button until the shade travels to the 75% closed position
2. TUG the shade hembar 6"~10" E 257"
3. single Channel Remote - PRESS and HOLD the DOWN button until the shade travels to UP '
the upper limit position D 50%
4. Multi Channel Remote — First select a channel to program: PRESS and RELEASE a
CHANNEL selection (16). Next. PRESS and HOLD the DOWN button until the shade
travels to the upper limit position DOWN > U D 75%
MASTER RESET - Will delete all learned remotes and limits on shade Qmotion"
1. PRESS and RELEASE the UP button to send the shade to the upper limit position
or manually roll the shade to the upper limit Single Channel
2. PRESS and HOLD the UP button, and CONTINUE HOLDING until the shade JOGS. travels to Remote
75% closed then starts to travel up. RELEASE the UP button when the final upward travel starts
3. TUG the shade hembar 6”—10"
4. At this point, the shade has been reset. All teamed remotes and limits have been deleted. To
learn a remote to the shade. PRESS and HOLD the UP button until the shade travels up
SPECIAL LEARN COMMAND — Start with Shade at the Upper Limit Position
1. PRESS and HOLD both UP and DOWN buttons at the same time until the shade travels down to
the 75% closed position
2. TUG the shade 6 inches to put the shade in team mode
3. Select a channel to add to the shade
4. PRESS and HOLD the UP button until the shade travels to the Upper Limit Position
www.qmottonshades.com Pensacola FL, 32514 1 477-849-6070 1
Dltl unnnn'u
CANADIAN REGULATORY STATEMENTS
This device complies with Industry Canada licence-exempt RSS standardis). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including Interference that may
cause undesired operation ufthe device.
Le present appareii est conforme aux CNR d'lndustrie Canada applicables aux appareils radio exempts de licence. L‘exploitation
est autorisée aux deux conditions suivantes : (1) i'appareil ne doit pas produire de brouillage, et (2) I'utilisateur de I'appareil doit
accepter tout broulllage radioélectrlque subi, mérne si Ie brouiilage est susceptible d'en compromeflre Ie fonctionnement.
Under industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio nterference to other users,
the antenna type and its gain should be so chosen that the equivalent isotropicaily radiated power (e.l.r.p.) is not more than that
necessary for successful communication.
Conformément a la réglementation d'lndustrie Canada, Ie present emetteur radio peut fonctionner avec une antenne d‘un type
at d'un gain maximal (ou inférieur} approuvé pour I'émetteur par industrle Canada. Dans ie but de rédulre Ies rtsques de brouil—
Iage radioéiectrique a i'intention des autres utilisateurs, i] taut choisir le type d'antenne et son gain de sorte que la puissance
isotrope rayonnée équivalente (p,i.r.e.) ne dépasse pas I'intensité nécessalre a I'établissement d'une communication satisfai—
same.
This equipment complies with the iCES RF radiation exposure limits set forth for an uncontrolled environment. This equipment
should be installed and operated with a minimum distance of 20cm between the radiator and any part of the human body.
Cet équlpement est conforme aux iimites d'exposition aux radiations iCES définies pour un environnernent non
contréié . Cet équipement doit étre instailé et utilise a une distance minimale de 20 cm entre ie radiateur et une
partie de votre corps.
FCC REGULATORY STATEMENTS
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions.
This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance
could void the user’sauthority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses, and can radi-
ate'radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encour-
aged to try to correct the interference by one or more of the following measures:
Reorlent or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is con-
nected.
Consult the dealer or an experienced radio/TV technician for help.
www.qmot1‘onshades.com Pensacola FL, 32514 1 -B77-B49-6070 2
DM nnnnmn

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.4
Linearized                      : No
Create Date                     : 2017:11:17 14:55:29-05:00
Page Count                      : 2
EXIF Metadata provided by EXIF.tools
FCC ID Filing: 2AHG4-MC433FM2

Navigation menu