The Whistler Group WH15 Radar Detector User Manual 1788
The Whistler Group Radar Detector 1788
Manual
TROUBLESHOOTING
FCC INFORMATION
CARE AND MAINTENANCE
OWNER’S MANUAL
SPEED MONITORING SPEED MONITORING
WARRANTY INFORMATION WARRANTY INFORMATION
ACCESSORIES
WARRANTY INFORMATION
14 15 17
16
VG-2 Audio/Visual Alerts
Note: You must turn this feature on before it will
detect VG-2.
When a VG-2 signal is detected, the detector ‘hides’ its own
radiated signal and becomes undetectable by the VG-2.
Every 30 seconds, the detector checks for a VG-2 signal.
If a VG-2 signal is still present, the unit continues to
hide and repeats the VG-2 alert. If no signal is detected,
two beeps are provided, indicating an ‘all clear’ condition.
During a VG-2 Alert X, K, and Ka band signals cannot
be received (Reference page 21 for VG-2 information).
Alert Priority
When two or more signals are received at the same
time, the alert priority is:
1.Laser
2.VG-2
3. Speed Radar
4.Safety Radar
Example:
If X band is alerting, then suddenly a VG-2 signal
is detected, the VG-2 warning will override the
Xband alert.
Reset Features
All user features can be reset to factory settings.
• Unplug Power Cord from unit.
• Press and hold Power and Quiet.
•Plug Power Cord into unit.
•Wait for 2 beeps.
• Release Power and Quiet buttons.
Unit is now reset to the following features
and settings.
Default factory settings are:
1.Audio to level (4).
2. Display shows Highway.
3. Auto Quiet Mode OFF.
4.VG-2 Detection Mode OFF.
5.Safety Radar OFF.
6. Vehicle Battery Saver to 1 hour.
7.Full Power Up sequence.
8.Default TONE 3.
9. POP ON.
10. Backlighting Dim/Bright
VG-2 ALERTS
• Check fuse for lighter socket; replace if necessary.
• Make sure lighter socket is clean.
PROBLEM: Unit alarms when vehicle hits bumps.
• Make sure batteries are seated properly.
• Make sure that the battery door is fully closed.
• Make sure battery contacts are clean.
• Check for loose lighter socket; tighten and clean.
• Check connections at both ends of power cord. Substitute
another cord to determine if cord is defective. Return
defective cord to the factory.
PROBLEM: Unit alarms when using vehicle electrical
accessories (brakes, power mirrors, power
windows, turn signals, horn, etc.) when unit is
connected to the power cord.
• Vehicle’s electrical system, including battery and alternator, may
have electrical noise. Install a filter capacitor (470mfd. 25 volt
or larger capacitance value) on the back of the lighter socket.
PROBLEM: Audio alerts are not loud enough.
• Cancel Auto Quiet Mode or City Mode.
• Check audio level setting (see page 8 & 9).
PROBLEM: Low Battery Life.
• Recharge the batteries using the home charger.
• One or more of the batteries may be defective.
• See the battery life tips on page 13.
If difficulties occur which cannot be solved by information
in this Troubleshooting Guide, please call Whistler
Customer Service at 1-800-531-0004 or visit our FAQ
page at www.whistlergroup.com/faq-detectors.asp,
before returning your unit for service.
18
ARE DETECTORS LEGAL?
19
In Most States YES!
Laser-Radar detectors are legal in every state (with
the exception of Virginia and Washington, D.C., which
have local regulations restricting the use of radar
receivers in any vehicle) when used in automobiles or
light trucks (under 10,000 lbs.).
Concerning trucks over 10,000 lbs., the Federal
Highway Administration (FHWA) issued a regulation,
effective January, 1994 which prohibits radar and laser
detector use in these types of vehicles nationally. Prior
tothe FHWA regulation, laws existed in the state of
New York restricting the use of radar detectors in trucks
over 18,000 lbs. and in Illinois in trucks over 26,000 lbs.
Care And Maintenance
During the summer months, avoid prolonged exposure
todirect sunlight by removing your unit from the dash
when your vehicle is parked for an extended period of
time. Do not spray water, cleaners, or polishes directly
onto the unit. The spray may penetrate through the
openings and damage the unit. Also, do not use any
abrasive cleaners on the unit’s exterior.
20
Radar Facts
Aradar gun operates by transmitting radio waves at
certain frequencies which reflect off objects and are
picked up by the radar gun’s receiving section. When
aradar beam reflects off a moving target, a measura-
ble frequency shift occurs. The radar unit converts this
shift into miles per hour to determine your vehicle’s
speed. Currently, the FCC (Federal Communications
Commission) permits operation of traffic radar guns
atXBand (10.500 - 10.550 GHz), K Band (24.050 -
24.250 GHz), and Ka Band (33.400 - 36.000 GHz).
Note: Aradar detector will not alarm if an officer is
not transmitting on any one of the above radar bands.
POP™ Mode
POP™Mode is a featureon some newer radar guns
operating on K and Ka bands. When the gun is in
POP™Mode and activated, a brief burst of energy,
less that 1/15 of a second, is transmitted and the
vehicle’sspeed is quickly acquired. A detector without
POP™Mode detection capability cannot respond to
this brief transmission.
SPEED MONITORING
FCC ID : HSXWH15
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device many not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
Important: FCC requirements state that changes
ormodifications not expressly approved by Whistler
could void the user’s authority to operate the
equipment.
21 22
Service Under Warranty
During the warranty period, defective units will be
repaired without charge to the purchaser when returned
with a dated store receipt to the address below. Units
returned without a dated store receipt will be
handled as described in section
“Service Out Of Warranty.”
Due to the specialized equipment necessary for testing
aLaser-Radar receiver,thereareno authorized serv-
ice stations for Whistler brand detectors other than
Whistler.
When returning a unit for service under warranty,
please follow these instructions:
1. Ship the unit in the original carton or in a suitable
sturdy equivalent, fully insured, with return
receipt requested to:
Whistler Repair Dept.
1201 North Dixieland Rd
Rogers, AR. 72756
Please allow 3 weeks turnaround time.
Important: Whistler will not assume responsibility
for loss or damage incurred in shipping. Therefore,
please ship your unit insured with return receipt
requested. CODs will not be accepted!
2. Include with your unit the following information,
clearly printed:
•Your name and street address (for shipping via
UPS),adaytime telephone number and an
email address, if applicable.
•Adetailed description of the problem (e.g., “Unit
performs self-test but does not respond to radar”).
•Acopy of your dated store receipt or bill of sale.
23
Laser Tips
If you are the targeted vehicle, a laser gun can often
determine your speed within a few seconds after you
receive an alert. In this situation there is generally no
time to safely adjust your speed. However, if you are
traveling near or behind the targeted vehicle and
receive an alert, response time should be sufficient.
Any laser alert, regardless of duration, requires
immediate action!
Other Speed Detection Systems
Several techniques other than radar or laser areused
to measure vehicle speeds. When these methods are
being used, no detector can provide a warning. These
techniques include:
•P
Pa
ac
ci
in
ng
g- A patrol car drives behind you and matches
your driving speed.
•V
Va
as
sc
ca
ar
r/
/A
Ai
ir
rc
cr
ra
af
ft
t- The time it takes a vehicle to travel
a known distance is measured.
Radar Detector Detectors: VG-2, Spectre
The Interceptor VG-2. or simply VG-2, is one type of
microwave receiver used by Police to detect signals
radiated by the local oscillator of a radar detector.
Because it purpose is to identify persons driving with
radar detectors, these devices are known as a “radar
detector detector” (RDD).
An RDD is the primary tool used by the police to identify
radar detectors equipped vehicles. If caught in a state or
country where detectors are illegal, (see page 18). drivers
risk losing their radar detector and receiving a fine. In
addition, instant-on radar is almost always used in
combination with a RDD, leaving unsuspecting motorists
vulnerable to receive two tickets - one potential for
speeding, the other for possession of a detector.
N
No
ot
te
e:
: H
Ha
av
vi
in
ng
g a
a r
ra
ad
da
ar
r d
de
et
te
ec
ct
to
or
r c
ca
ap
pa
ab
bl
le
e o
of
f d
de
et
te
ec
ct
ti
in
ng
g t
th
he
e
V
VG
G-
-2
2 m
ma
ay
y a
al
le
er
rt
t y
yo
ou
u t
to
o t
th
he
e p
pr
re
es
se
en
nc
ce
e o
of
f a
a s
sp
pe
ee
ed
d t
tr
ra
ap
p.
.
T
Th
he
e n
ne
ew
we
es
st
t t
to
oo
ol
l P
Po
ol
li
ic
ce
e h
ha
av
ve
e t
to
o d
de
et
te
ec
ct
t r
ra
ad
da
ar
r d
de
et
te
ec
ct
to
or
rs
s i
is
s
c
ca
al
ll
le
ed
d S
Sp
pe
ec
ct
tr
re
e.
. A
As
s o
of
f t
th
hi
is
s p
pr
ri
in
nt
ti
in
ng
g.
. S
Sp
pe
ec
ct
tr
re
e c
ca
an
n d
de
et
te
ec
ct
t a
al
ll
l
u
un
nd
de
et
te
ec
ct
ta
ab
bl
le
e (
(V
VG
G-
-2
2)
) l
la
as
se
er
r/
/r
ra
ad
da
ar
r d
de
et
te
ec
ct
to
or
rs
s o
on
n t
th
he
e m
ma
ar
rk
ke
et
t.
.
It is the responsibility of the individual radar detector
owner to now and understand the laws in your area
regarding the legality of the use of radar detectors.
Consumer Warranty
This Whistler Laser-Radar detector is warranted to the
original purchaser for a period of one year from the date
of original purchase against all defects in materials and
workmanship. This limited warranty is void if the unit is
abused, modified, installed improperly, if the housing
and/or serial numbers have been removed.There are no
express warranties covering this product other than
those set forth in this warranty. All express or implied
warranties for this product are limited to the above time.
Whistler is not liable for damages arising from the use,
misuse, or operation of this product.
N
No
ot
te
e:
:Damaged caused by incorrect battery
placement or battery leakage is not covered under
this warranty.
3. Be certain your unit is returned with its serial number.
For reference, please write your unit’s serial number
in the following space: s/n_______________.
Units without serial numbers are not covered under warranty.
Important: To validate that your unit is within the
warranty period, make sure you keep a copy of
your dated store receipt. You may register your
warranty online at www.whistlergroup.com,
however, for warranty verification purposes, a
copy of your dated store receipt must accompany
any unit sent in for warranty work.
Service Out of Warranty
Units will be repaired at ‘out of warranty’ service
rates when:
• The units original warranty has expired.
• A dated store receipt is not supplied.
• The unit has been returned without its serial number.
• The unit has been abused, modified, installed
improperly, or had its housing removed.
The minimum out of warranty service fee for your
Whistler detector is $55.00 (U.S.). If you require out
of warranty service, please return your unit as outlined
in the section “Service Under Warranty” along with a
certified check or money order for $55.00. Payment
may also be made by MasterCard, VISA or American
Express; personal checks are not accepted.
In the event repairs cannot be covered by the
minimum $55.00 service fee, you will be contacted
by a Whistler technical service specialist who will
outline options available to you.
If you elect not to have your unit repaired, it will be
returned to you along with your certified check or
money order.
24 25
SPECIFICATIONS
Dimensions: 5.3125” L x 3.125” W x 1.375” D
Weight with Batteries: 11.2oz.
Weight without Batteries: 6.4oz.
Laser Wavelength: 905 ± 50 nanometers (nm)
Radar Frequencies:
10.500 - 10.550 GHz (X Band)
24.050 - 24.250 GHz (K Band )
33.400 - 36.000 GHz (Ka Superwideband)
Operating Temperature Range: -20˚ C to +80˚ C
(-4˚ F to +176˚ F)
Power Requirements:
4 AA Ni-MH batteries 4.8 volts.
12 volts with power cord.
One or more U.S. patents may apply:
#5,146,227, #5,379,456, #5,666,120, #5,990,821
POP™ Mode is a trademark of MPH Industries, Inc.
Specifications are subject to change without notice.
Important: When returning your unit for service, be
certain to include a daytime telephone number and
an email address (if applicable).
Customer Service
If you have questions concerning the operation of your
Whistler detector, or require service during or after
the warranty period, please call Customer Service at:
1-800-531-0004
Representatives are available to answer your questions
Monday - Friday from 8:00 a.m. to 5:00 p.m. (CT) or
visit the FAQ’s at www.whistlergroup.com.
The Whistler Group Corporate Headquarters
13016 N. Walton Blvd. • Bentonville, AR 72712
Tel 479.273.6012 • Fax 479.273.2927
Customer Return Center
1201 N. Dixieland Rd. • Rogers, AR 72756
Customer Service Tel 800.531.0004
www.whistlergroup.com
P/N 203322,
©
2005 The Whistler Group, Inc.
These and other accessories can be ordered directly
from Whistler by calling 1-800-531-0004 or by visiting
our online store at www.whistlergroup.com
*Modular: Interconnecting pieces cord and plug. Shipping and
handling (per order) $7.50 Prices are subject to change without notice.
26
RESET FEATURES
POP™ MODE ALERTS SPEED MONITORING
WARRANTY INFORMATION
Total Band Protection™
Complete Band Coverage that detects laser, radar,
VG-2 and safety radar bands.
Laser Facts
It’s well documented that many radar guns cannot
reliably provide the speed of a targeted vehicle that
is traveling in a group of vehicles. In contrast, a laser
gun can target a specific vehicle out of a line of traffic
and determine its speed. The advantage of laser
over radar in terms of target identification is the result
of the laser gun’s narrow beam. A radar gun’s
transmission can cover more than a four-lane highway
at a distance of 1,000 feet, compared with a laser
gun’s transmission which covers about 3 feet at the
same distance. For best protection, keep these
points in mind:
•Because the vehicle’s license plate or headlights
are the laser gun’s primary targets, mounting the
Whistler detector on the dashboard can improve
laser detection at short range.
•Do not follow closely behind any vehicle you cannot
see through. If you can’t see past a vehicle ahead
of you, chances are your detector won’t either.
• The receiving range of your laser detector will not
be the same as a radar detector. Laser guns are
most often used at short range.
Whistler Laser-Radar detectors receive all current laser
guns which operate at a laser wavelength of 905 +/- 10mm.
•Pro Laser™I II III •LT1 20-20 •Ultra Lyte
LASER/RADAR ALERTS
POP™ Mode Alerts
Because POP™ Mode travels on regular radar bandwidth,
there is no particular alert for POP™ Mode transmissions.
POP™ Mode alerts will be displayed as a regular radar alert.
Speed Radar Audio/Visual Alerts
When X, K or Ka is detected, the band ID and signal
strength is displayed. The audio alert is continuous
and has a geiger counter-like pattern. The faster the
beep, the closer or stronger the radar source.
Laser Audio/Visual Alerts
When a laser signal is detected the audio alert is continuous
for a minimum of 3 seconds.
• The Displays Shows:
The more “|||” the closer the laser source.
Pulse Protection®
Pulse (or instant-on) radar is more difficult to detect
than conventional radar because it remains ‘off’ until
activated to measure the speed of a targeted vehicle.
When a pulse type transmission is detected, your Whistler
detector sounds an urgent 3-second audio warning
and the display shows:
After the 3-second pulse alert, the standard alert pattern
continues for as long as the signal is present.
It is important to respond promptly to a pulse alert,
since warning time may be minimal.
1788
Battery Powered
LASER-RADAR
DETECTOR
Your Whistler detector is expertly engineered and
designed to exacting quality standards to provide
you with reliable, trouble-free operation. If your unit
has been correctly installed following the guidelines
in this manual, but is not operating optimally, please
refer to the troubleshooting guide below.
PROBLEM: No display or audio.
• Make sure batteries are installed with the correct polarity.
• Make sure batteries are fully charged.
• Make sure battery contacts are clean.
• Check fuse in Whistler plug; replace if necessary with a 2
amp 3AG type.
TROUBLESHOOTING
INTRODUCTION TABLE OF CONTENTS INSTALLATION CONT.
WHISTLER FEATURES FEATURE DESCRIPTIONS
OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION OPERATION
Dear Whistler Owner,
The Whistler 1788 features the newest POP™ Mode
detection capability combined with the convenience and
portability of a battery operated unit. The problem with
some battery operated laser-radar detectors is that the
receiver shuts down for 30 to 50 percent of the time to
conserve battery life, leaving the driver vulnerable. During
this time the display is left on to give you the feeling of full
time protection, which is not true. This is not the case with
the Whistler 1788.
The Whistler 1788, provides cordless detection and is
powered ON 100 percent of the time. This unit provides
Complete Band Protection and is packed full of features.
Some of the features include:
•POP™ Mode Detection Capability operating on
K and Ka bands. This mode acquires the vehicle's
speed in less than 1/15 of a second.
•Blue Backlit LCD Text Display provides easy to read
band identification and signal strength.
•Built-in Battery Charger automatically
recharges the unit when the power cord is
connected.
•Stay Alert tests alertness on long trips.
Even though this unit is packed full of features it is still very
easy to use. To fully utilize your unit to its potential, we
recommend reading this entire manual or visit our
FAQ page on our web site www.whistlergroup.com.
Enjoy your new Whistler and please drive safely.
Sincerely,
The Whistler Group, Inc.
3
1
9
8
7
2
6
45
3
10
12
• Battery Operated
With Built-in Battery Charger
• Total Band Protection™
• POP™Mode Detection
• Blue LCD Text Display
• High Gain Optical Lens
• Stay Alert™
• 360° Total Perimeter Protection™
• VG-2 Cloaking™ T
echnology
• 3 City Modes
• Quiet/Auto Quiet Modes
• Vehicle Battery Saver
• Setting Saver
• Alert Priority
• Safety Warning System™
Accessories:
Windshield Bracket Kit, Batteries, Straight
Power Cord & Home Battery Charger
increased sensitivity and field of view for leading-edge
laser detection.
6. Rear Laser Antenna – An integrated optical
waveguide provides superior detection of laser
signals transmitted from behind.
7. City Button - Reduces the annoyance of false
alerts typically encountered in urban driving areas.
8. Quiet/Menu Button - Pressing QUIET before a
signal is detected engages Auto Quiet Mode which
automatically reduces the audio level after the initial
warning to a low audio level setting. Pressing QUIET
during a radar/laser encounter silences audio alerts,
while allowing visual alerts to keep you informed.
(Pressing and holding for 2 seconds allows you to enter
Option Select Mode—see page 11.
9. Power/Dim -Turns unit on/off and engages
Backlight settings (press and hold).
10. Volume Up/Down Buttons – Adjust volume up or down.
11. Blue LCD Text Display – Provides distinct visual
confirmation of signals detected, signal strength,
and indicates engaged modes of operation.
12. Power Jack – Provides connection for the power cord.
13. Battery Compartment – Compartment for which
you place the batteries.
Battery Installation
This unit requires 4 AA batteries (included).
P
Pl
le
ea
as
se
e c
ch
ha
ar
rg
ge
e b
ba
at
tt
te
er
ri
ie
es
s o
ov
ve
er
rn
ni
ig
gh
ht
t b
be
ef
fo
or
re
e f
fi
ir
rs
st
t u
us
se
e!
!
• Remove the battery compartment cover by sliding
the cover to the edge of the unit and lift up.
•Observing correct polarity (+) and (-), insert
batteries as shown.
• Reinstall battery compartment cover. For best
performance we recommend using the highest
capacity rechargeable AA batteries available.
Alkaline batteries are not recommended.
456
Battery Installation (Continued)
Ni-MH rechargeable batteries are recommended and
are included with the unit. Common rechargeable
batteries have a power rating of 2100 mA or higher.
N
No
ot
te
e:
:DO NOT mix battery types as this can damage
the batteries. Lithium batteries are recommended for
use in cold temperatures. As with all battery
operated devices, remove the batteries when this
unit will not be used for an extended period of time.
Damage caused by leaky or improperly charged
batteries are not covered under warranty. Check with
the battery manufacturer about their specific
product warranty and disposal recommendations.
I
Im
mp
po
or
rt
ta
an
nt
t:
:Ni-Cd batteries are not recommended.
These batteries will not provide enough capacity to
be useful. Replace the Ni-Cd’s with Ni-MH type
rechargeable batteries.
C
Ca
au
ut
ti
io
on
n:
:Only use rechargeable batteries in the
supplied battery charger. Charging non-rechargeable
batteries can damage the charger or possibly cause
the batteries to explode.
Mounting Guidelines
•Mount the unit as low as possible near the center
of the windshield.
• Do not mount your unit behind wipers, ornaments,
mirrored sunscreens, etc. These obstructions have
metal surfaces which can affect radar and laser
signals and reduce critical warning time. (Regular
tinted glass does not affect reception.)
•Some windshields have an Instaclear™or Electriclear™
type coating, which affect radar signals. Consult your
dealer or the owner’s manual supplied with your vehicle
to determine if your windshield has this coating.
•Avoid placing unit in direct contact with windshield.
• To reduce the possibility of theft, conceal your unit
when not in use.
7
Power On and Self-Test
Each time your Whistler detector is turned on, an
automatic self-test sequence confirms that the
speaker and visual displays are functional.
• Press Power. Display shows in order:
1. WHISTLER 2. X-Band 3. K-Band 4. Ka-Band
5. LASER 6
6.POP ON 7. VG2 OFF 8. SR OFF
9. Bat Full - This will display the battery status. 10. Highway
Battery Charging
External - The included battery charger provides
approximately 10 hour recharge time for Ni-MH
batteries. Simply observe the battery polarity when
installing the batteries into the charger and plug the
charger into a convenient outlet.
Internal - While traveling and if the batteries become
weak, plugging in the external power cable not only
will power the unit but also charge the batteries. The
display will show an asterisk, i.e.,
when the unit is charging the batteries. The asterisk
will flash during charging and go out when charging
is complete. N
No
ot
te
e:
: The charging time is similar to a
home charger.
External Power
The unit can be powered externally using the
power cable. This is handy in case the batteries
become weak and you are away from an outlet to
use the home charger or can not get to a store for
replacement batteries. Simply plug the power cable
into the power jack and your ready to go. The unit
will slowly charge the batteries while traveling. See
Battery Charging section for more information. When
the power cable is removed from the unit or the
vehicle’s lighter socket is switched off, the unit will
alarm and display then simply turns off.
89
Setting Saver
Setting Saver saves your personalized settings so
that when the detector is turned off and then on
again, you do not have to re-enter them.
Feature Engaged Confirmation
Each time a button is pressed one beep confirms
feature “on”, two beeps confirm feature “off”.
Audio Level Adjustment
The audio levels can be adjusted high to low or low
to high.
• Press Volume up to increase audio level.
•Press Volume down to decrease audio level.
As audio level is adjusted, beeps are provided and
the display indicates volume level. Note: In certain
cases the voice message does not replicate the text
message.
Auto Quiet Mode
Auto Quiet reduces the selected audio level to level
(1) approximately 5 seconds after a radar or safety
radar signal is detected. The alert for any new signal
within 20 seconds will resume at level (1). Auto Quiet
does not affect VG-2 or laser alerts.
• Press Quiet/Menu (before a signal is detected) to
engage Auto Quiet.
• Once the Auto Quiet mode is engaged, you may
cancel the audio alarm by pressing Quiet.
• Press Quiet (when the unit is not alarming) to
cancel Auto Quiet mode.
Quiet Mode
Quiet cancels audio during an alert and any new alert
within 20 seconds. After 20 seconds, approximately
2 beeps are provided on any new alert and unit then
remains quiet.
•Press Quiet to cancel the audio.
• Press Quiet a second time during an alert to restore
Quiet Mode (Cont.)
the standard audio alert pattern; or turn the unit
off, then on.
City/City 1/City 2 Mode
Whistler’s Three Stage City Mode is designed to reduce
the annoyance of automatic door openers, intrusion
alarms and other devices which share frequencies with police
radar. Generally, X band is used for these devices.
• Press City to cancel Highway mode and engage City.
• Press City again to enter City 1 Mode
- display shows ‘C1 Lo X’.
• Press City again to enter City 2 Mode
- display shows ‘C2 No X’
• Pressing City a fourth time cancels City 2 Mode
and returns the unit to Highway Mode.
In City Mode, weak speed/safety radar signal give an
initial alarm of two beeps, and then remains quiet
unless the signal becomes very strong. When the
signal strength increases, two additional beeps are
provided. City 1 and City 2 Modes operate the same
as Highway Mode, but in City 1 Mode, only the X band
sensitivity is lowered. In City 2 Mode, X-band is not
detected.
Caution: Some towns/small cities may still be using X
band radar. City Modes do not change the audio
alert for laser or VG-2.
Highway Mode
Highway mode provides full audio warnings any time
radar (X, K, Ka, Safety Radar) or laser signals are
detected, and is recommended for open road driving.
For more information on City and Highway mode, please visit
our FAQ page on our website: www.whistlergroup.com
Backlight Setting
The backlighting can be programmed to be illuminated
all the time, only when alarming, or choices in-between.
The options are selectable by pressing and holding the
Dim button on the unit. The options are:
OFF-OFF = Backlight is off during normal operation
and off when the unit alarms
OFF- DIM = Backlight is off during normal operation
and dim when the unit alarms.
OFF-BRT = Backlight is off during normal operation
and bright when the unit alarms.
DIM-OFF = Backlight is dim during normal operation
and off when the unit alarms.
DIM-BRT = Backlight is dim during normal operation
and bright when the unit alarms.
Backlight will turn on, if selected, while the unit alarms
and remain on for 3 seconds after the unit stops
alarming. When any button is pressed the backlight will
illuminate at the dim setting and remain on for 3
seconds afterwards. The backlight will also illuminate
while in option mode.
Engaging/Disengaging VG-2
See Option Select Mode to turn this feature on/off.
When a VG-2 signal is detected, the VG-2 is sounded
and the VG-2 display flashes. After 3 seconds the
audio is canceled and the display no longer flashes.
This cycle is repeated if the VG-2 signal is again
detected.
During the period a VG-2 signal is detected, a radar
signal cannot be detected. However, because the VG-2
alert has confirmed that a patrol car is nearby, you are
already aware of the potential for speed monitoring
and can adjust your speed accordingly. Laser detection
is not affected while a VG-2 signal is detected.
Teach/Tutorial Mode
Provides simulated alerts for each type of signal.
• Press City and Quiet simultaneously and release.
• Display Shows:
• Press Power to exit.
10 11
Option Select Mode
Entering Option Select Mode allows you to customize options
such as Tone Select, Abbreviated Power Up Sequence and
VG-2 Mode. Press and hold quiet button to enter OPT
Select mode. When selecting options, the , or Q
must be pressed within 20 seconds or options mode will
automatically be exited. To enter:
12 13
Vehicle Battery Saver Mode
The Vehicle Battery Saver Mode automatically shuts off
the detector if you forget to turn it off. The timer is reset if
the detector is turned off, unplugged or any button is
pressed before the timer has expired. The detector will alert
you with an audible and visual warning before it shuts
off. This auto off function can be programmed for the
following: Off, 1, 2, or 3 hours.
During this warning you can reset the time by pressing
any button. This will reset the timer.
If the unit has automatically turned itself off, press the Power
button to turn the unit back on. You can manually engage
the Vehicle Battery Saver Mode by pressing and holding
the City button until one beep is heard.
Refer to “Option Select Mode” for instructions for
changing the battery saver mode settings.
Stay Alert Feature
The Stay Alert Feature is designed to test a driver’s
alertness. To engage (when unit is not alarming) :
• Press and hold City for approximately 2 seconds.
Release button during or immediately after the alert
is given.
—Display shows:
Within 30-60 seconds two beeps are sounded; to
show alertness, the driver must press either the City,
Volume, or Quiet buttons within 3-5 seconds. If a button
is pressed within 3-5 seconds, the cycle is repeated.
If a button was not pressed within 3-5 seconds alarm
sounds and the display shows:
•Press Power to exit.
Model Features Summary.............................3 - 4
Installation................................................... 4 - 6
•Battery Installation ............................................. 4 - 5
•Mounting Guidelines..............................................5
•Windshield Mounting.............................................6
•Power Connection and Fuse Replacement............. 6
Operation.................................................. 7 - 13
•Power On and Self-Test.......................................... 7
•Battery Charger.......................................................... 7
•Setting Saver......................................................7 - 8
•Feature Engaged Confirmation.............................. 8
•Audio Level Adjustment........................................ 8
•Auto Quiet Mode....................................................8
•Quiet Mode........................................................8 - 9
•City/City 1/ City 2 Mode...................................... 9
•Highway Mode....................................................... 9
•Backlight Setting..............................................9 - 10
•Engaging/Disengaging VG-2...............................10
•Teach/Tutorial Mode............................................ 10
•Option Select Mode................................................ 11
•Vehicle Battery Saver Mode..................................12
•Stay Alert Feature........................................... 12 -13
Safety Warning System™.................................13
• Battery Life ..............................................................13
POP™Mode Alerts..........................................14
Laser/Radar Alerts..........................................14
•Speed Radar Audio/Visual Alerts....................... 14
•Laser Audio/Visual Alerts................................... 14
•Pulse Protection®...................................................14
VG-2 Alerts.................................................... 15
•Alert Priority......................................................... 15
Reset Features................................................16
Troubleshooting Guide..............................16 - 17
Care and Maintenance................................... 18
Are Detectors Legal?.................................... .18
FCC Information............................................ .19
Speed Monitoring.................................... 19 - 22
•Radar Facts............................................................19
•POP™Mode........................................................... 19
•Total Band Protection™..........................................20
•Laser Facts.............................................................20
•Other Speed Detection Systems...................21 -22
Warranty Information...............................22 - 25
Specifications................................................. 25
Accessories.....................................................26
11
INSTALLATION
Windshield Mounting
•Install the two suction cups and rubber bumper onto
the bracket by fitting them into their holes.
• Press the suction cups onto the windshield at the
location you have chosen.
Important: Some newer cars have a plastic safety
coating on the inside of the windshield. The windshield
bracket may leave permanent marks on this type of
surface. To find out if your vehicle has this type of
windshield, check the owner’s manual or ask your dealer.
We recommend that you do not leave the suction cup
bracket on the window in direct sunlight. If the detector
is removed, this may cause blistering of the dash in
some vehicles.
•Slide the detector onto the bracket until it locks into place.
• If necessary, the unit may be leveled by bending
the windshield bracket. Press the bracket release
button and remove the detector before bending.
Power Cord Connection
• Plug the small end of the power cord into the
unit’s power jack.
• Plug the large end into the vehicle’s cigarette lighter.
N
No
ot
te
e:
:Cord fits tightly into detector. When installing
the cord, expect some resistance.
Fuse Replacement
The lighter socket plug is equipped with a replaceable
2 amp 3AG fuse located behind the silver tip. To
replace the fuse, carefully unscrew the tip of the plug.
I
Im
mp
po
or
rt
ta
an
nt
t:
:Unscrew slowly. The tip contains a spring
which may fly out when disassembling. Insert the
new fuse with the spring and screw on the tip. With
use, screw cap on plug may loosen. Retighten
occasionally.
Unscrew the tip of the lighter socket plug
carefully when replacing the 2 amp fuse.
Stay Alert Feature (Cont.)
WARNING!!! Stay Alert is NOT intended as a substitute
for adequate rest. You should NOT operate a vehicle if you
are drowsy. During extended periods of vehicle operation,
you should take frequent breaks. Improper reliance on the
Stay Alert feature may result in vehicle damage, personal
injury or death. NEVER OPERATE A VEHICLE IF YOU
ARE DROWSY.
Safety Warning System™
In communities where transmitters are located,
the Safety Warning System™displays over 60 text
messages. When Safety Radar is detected the audio
alert is geiger counter-like.
Safety Warning System Text
Example: Poor - Road - Surface.
Note:
Not all areas have Safety Warning System™transmitters.
Battery Life
The unit can provide over 20 hours of laser/radar detec-
tion. There are settings that can maximize battery life.
1) Backlighting set to OFF-OFF
2) Auto Quiet to ON
3) Battery saver set to 1 hour
4) Using a lower volume setting
5) Using Mute whenever possible
SWS™
If you have questions concerning the
operation of this Whistler product
please call:
CuSTOmer SeRVICE
1-800-531-0004
Monday - Friday • 8:00 am - 5:00 pm CT
or visit our website
www.whistlergroup.com
Please keep the receipt in a safe place.
You may register your product online
at www.whistlergroup.com. For warranty
verification purposes, a copy of your
dated store receipt must accompany any
unit sent in for warranty work. If the
unit is returned without a dated store
receipt, an out of warranty service charge
applies. Note: Your warranty period begins
at the time of purchase. The warranty is
validated only by the dated store receipt!
Now is the time to record the serial
number of the unit in the space provided
in the warranty section of the manual.
1788
FEATURE DESCRIPTIONS
Whistler’s ergonomic and user-friendly design provides a
new level of operating convenience. Special features
include:
1. Bracket Release Button – Provides quick and
easy release of the mounting bracket.
2. Speaker – Provides distinct audio warnings for X,
K, Ka band radar, safety radar, laser and VG-2.
3. Mounting Bracket Location – Slot holds mounting
bracket firmly.
4. Radar Antenna – Compact, high-efficiency antenna
receives radar signals.
5. Front Laser Antenna –High gain optical lens provides
INSTALLATION
13 Windshield
Mounting