Thomas and Betts RC3120R Wireless Door Chime User Manual 47912

Download:
Mirror Download [FCC.gov]
Document ID	47912
Application ID	CQLkFyLtpieYlm+B8vL0mQ==
Document Description	8
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	3.79kB (47338 bits)
Date Submitted	1999-07-14 00:00:00
Date Available	1998-09-16 00:00:00
Creation Date	2001-06-12 22:09:46
Producing Software	Acrobat Distiller 4.0 for Windows
Document Lastmod	2001-06-12 22:09:48
Document Title	47912.pdf
Document Author:	jsoscia

INSTRUCTION GUIDE
Plug-in DoorBell RC3120R'
Congratulations on a wise purchase!
COMPONENTS:
n..--
Doorbell Receiver
Doorbell Button
Double—sided tape
One 12—Volt alkaline battery
Plastic Plugs (2)
Screws
TOOLS NEEDED:
Small F lat head screwdriver
Small Philips head screwdriver
BATTERY INSTALLATION:
Doorbell Button
1.
2.
3.
4.
Gently insert screwdriver in small opening on the bottom of doorbell button.
Slightly turn the screwdriver to release the back cover
Install included 12-Volt alkaline battery Be sure battery (+) and (—) terminals
match (+) and (-) contacts shown on doorbell button.
Replace battery covere (Note: If you plan to mount the button transmitter
with screws, please defer this last step until after mounting back cover -
see mounting below)
TEST:
2.
Plug Doorbell Receiver into any ive" 110~vclt AC outlet not controlled by a
switch
Press Doorbell Button. Receiver should play ing dong” tone. Red light on
Doorbell Button should illuminate if battery is OK.
MOUNTING DOORBELL BUTTON:
Note: Mounting Doorbell Button on aluminum siding or metal door frame may
reduce range. Mount Button with red LED light on top,
1. For tape mounting:
A. Make sure surfaces are free of dust, oil, and other substances that
could affect adhesion.
B. Attach double—sided tape to back of Doorbell Button housing.
C. Press tape firmly to mounting surface.
2. For screw mounting:
A. Place back of Doorbell Button where desired and mark screw
locations.
nu.
B For wood surface drill 1/16 pilot holes. For drywall surfaces drill
3/1 6" holes for plastic anchors.
C. Insert screws into holes or drywall anchors in transmitter back cover
and screw into place.
D. Snap transmitter onto back cover by inserting the top first and
pushing the bottom firmly in place.
3. Doorbell Button may also be used as a hand—held pager.
TROUBLESHOOTING TIPS:
PROBLEM: Nothing happens when doorbell Button is pressed.
SUGGESTIONS: Check to see that the Doorbell Button red light illuminates.
Verify that battery is installed correctly. Check that outlet is functioning. Check that
receiver is within 100 ft. operating range of the button.
PROBLEM: Receiver sometimes plays without anyone pressing Doorbell Button.
SUGGESTION: If another Wireless Doorbell system is on the same frequency
nearby, it could accidentally trigger your system. If this happens, consider
purchasing a different Dimango Doorbell which allows selection of privacy codes.
This device complies with FCC rules part 15 and with RSS‘210 of the Industry
Canada. Operation is subject to the following two conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that
may cause undesired operation.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.3
Linearized                      : Yes
Create Date                     : 2001:06:12 22:09:46
Producer                        : Acrobat Distiller 4.0 for Windows
Author                          : jsoscia
Title                           : 47912.pdf
Modify Date                     : 2001:06:12 22:09:48-04:00
Page Count                      : 2

EXIF Metadata provided by EXIF.tools