Tivo Series 2 80 Hour Dual Tuner Digital Video Recorder Sdoc 00102 001 Users Manual Series2 DVR Start Here Poster
TCD649080 to the manual 6aa41edd-1e16-40bd-8931-72d5da564251
2015-02-02
: Tivo Tivo-Tivo-Series-2-80-Hour-Dual-Tuner-Digital-Video-Recorder-Sdoc-00102-001-Users-Manual-449878 tivo-tivo-series-2-80-hour-dual-tuner-digital-video-recorder-sdoc-00102-001-users-manual-449878 tivo pdf
Open the PDF directly: View PDF 
.
Page Count: 2
| Download | |
| Open PDF In Browser | View PDF |
Welcome! Start Here Setting up your TiVo® Series2TM DT Digital Video Recorder (DVR) is easy. There are three basic steps: SDOC-00102-001 Rev A1 Activate the TiVo® service. If you haven’t already activated, visit www.tivo.com/activate or call TiVo Customer Support at 1-877-367-8486. You’ll need your 15-digit TiVo Service Number, found on the label on the back of the DVR. Write it here: _____________________. Connect your TiVo® DVR. Connect your TiVo DVR to your TV programming source (basic cable, digital cable, or satellite), to your home network or home phone line, and to your TV. Complete Guided Setup. After you connect everything, Guided Setup screens help you customize the DVR for your home. That sounds easy enough, right? Consult the Viewer’s Guide for additional setup examples, or if you need any help along the way. Start Here To begin, please answer this first question: What is your TV Programming Source? Basic Cable (no cable box) Follow these easy steps to connect your TiVo® DVR Start with step below. Basic Cable (no cable box) Use Cable Bag A Phone cord Cable Box Satellite Turn this poster over, and start with step on the other side. Go to Appendix A in the Viewer’s Guide. If you have a cable box, turn this poster over Composite A/V cable for stereo audio (red & white ends) & video (yellow end) Phone splitter Coaxial RF cable for audio & video Connect your TV programming source Power cord Connect the Coaxial RF cable coming out of the wall to the CABLE RF IN jack on the DVR. The DVR’s internal RF splitter enables dual tuner for basic cable. Note: If you have a cable box, turn this poster over. Tune your TV (if necessary) to see the Welcome screen Turn on your TV. Tip: If you don’t see the Welcome screen, use the TiVo® DVR Plug in the power cord Lights on the front panel show that it’s powered on. Input, Source, or TV/Video button on your TV remote or TV to select the correct audio/video source. Press the button until you see the Welcome screen. Alternate: If you used a Coaxial RF cable in Step , tune your TV to the same channel (either 3 or 4) that the CHANNEL 3/4 switch on the back of the DVR is set to. When you see the Welcome screen, you’re ready to begin Guided Setup, which customizes the DVR for your home. If you need help, see the Troubleshooting chapter in the Viewer’s Guide or visit www.tivo.com/setup. Connect your TV Television Connect a Composite A/V cable (red, white, and yellow) from the DVR’s OUT jacks to your TV’s Audio/Video INPUT. Alternate: If your TV doesn’t have Composite A/V (red, white, and yellow) input jacks, connect a Coaxial RF cable from the CABLE RF OUT jack on the DVR to the Antenna In jack on your TV. Then set the CHANNEL 3/4 switch on the back of the DVR, and tune your TV to the same channel. Connect to the TiVo® service: Network OR Phone Your TiVo DVR needs to connect to the TiVo service to receive program listings, service updates, and other information. Choose how your DVR will connect: Network or Phone INPUT Network Choose this option if you have a home network with a broadband Internet connection. Use the connection that works with your type of home network: Wired or Wireless ETHERNET USB 1 USB 2 R L VIDEO Antenna In Connect all cables from the OUT jack of one device to the IN jack of the next. Wired (Ethernet) – Connect an Ethernet cable (sold separately) from your home network to the TiVo DVR’s Ethernet jack (the upper jack pictured here). OUT IN OR Wireless – Connect a compatible wireless USB network adapter (sold separately) to one of the DVR’s USB ports. The TiVo® Wireless USB adapter pictured here is available at www.tivo.com/store. Never connect OUT to OUT or IN to IN. OUT OUT Phone Choose this option if you don’t have a home network with a broadband Internet connection. Connect the provided phone cord from the DVR to a nearby wall jack. Use the provided phone line splitter if the DVR is sharing the wall jack with a telephone. Cool Things You Can Do Record Two Shows at Once The TiVo® Series2TM DT can record two basic cable channels (typically 1-99) at the same time. If you have a cable box, turn this poster over for details. You can learn a lot in a short Tour! Grab your TiVo remote and open the Viewer’s Guide to Chapter 1: The Basics in 5 Short Tours. Find What’s on TV ® TiVo Central screen & Now Playing List Live TV ® Info r TV Powe Input T V e G uid W The TiVo button takes you to TiVo Central, where you access all of the features unique to the TiVo® service. Use Pick Programs to Record to schedule recordings of your favorite shows. Press the TiVo button twice to go to the Now Playing List and see all of your recorded programs. To see what’s on now, press LIVE TV. Press LIVE TV again to switch between the two tuners. Press GUIDE to see the Program Guide and browse up to two weeks of program listings. Use either of two guide styles to choose programs to watch or record. Need some help? I don’t see the Welcome screen. My TiVo® remote isn't working. • Make sure all cables are connected from the OUT jack of one device to the IN jack of the next. Never connect OUT to OUT or IN to IN. • Notice the red light above the TiVo button on the remote. If the red light does not flash when you press any button, try replacing the batteries. • If you used a Coaxial RF cable to connect your DVR to your TV, make sure your TV is tuned to the same channel (3 or 4) that you selected on the back of your DVR (using the channel 3/4 switch). • Do lights on the front of the TiVo DVR seem to respond (i.e., blink or flash) when you press any button on the remote? If lights on the front of the DVR do not respond to the remote, restart your DVR by unplugging it, waiting 15 seconds, then plugging it back in. indow • Make sure your TV is displaying the appropriate video source. You may need to use the Input, Source, or TV/Video button on your TV’s remote to change video sources. If you are having trouble changing the video source, refer to your TV owner’s manual. t Se le c Vo l R te Mu Chan ecord Page Play • If you connected the DVR to an A/V receiver or home theater system, and you are having trouble finding the correct input, try connecting it directly to the TV instead. Sl o w 1 DVR 2 • See the inside front cover of the Viewer's Guide for more about the TiVo remote. I have a question about Guided Setup. • If you’re stuck at any point during Guided Setup, consult the Troubleshooting chapter of the Viewer’s Guide or visit www.tivo.com/setup. 3 2 1 6 5 4 9 8 ar Cle Tell Your TiVo® DVR What You Like Rate programs using the THUMBS buttons. Then check out TiVo Suggestions (in Pick Programs to Record) and watch for recorded suggestions in the Now Playing List. En 7 0 /Last ter Control Live TV Pause live TV for up to 30 minutes, rewind and fast forward at three speeds, slow motion, and instant replay–all at the touch of a button. Check out the Troubleshooting chapter in the Viewer’s Guide for more help with connecting your TiVo DVR, completing Guided Setup, and using the TiVo service. If you have more questions, visit www.tivo.com/support to find the Getting Started Guide, Help Forums, Guided Troubleshooting, Frequently Asked Questions, and more. www.tivo.com/support © 2006 by TiVo Inc. All rights reserved. Reproduction in whole or in part without written permission is prohibited. Printed in Mexico. TiVo, the TiVo logo, TiVo, TV Your Way, TiVo Central, WishList, Season Pass, TiVoToGo, Series2, the Series2 logo, the Advance logo, the Instant Replay Logo, the Thumbs Up logo, the Thumbs Down logo, Overtime Scheduler, Overlap Protection, Ipreview and the sounds used by the TiVo service are trademarks or registered trademarks of TiVo Inc. or its subsidiaries, 2160 Gold Street, P.O. Box 2160, Alviso, CA 95002-2160. All other trademarks are the properties of their respective owners. All rights reserved. Cable Box Use Cable Bag If you don’t have a cable box, turn this poster over Composite A/V cable for stereo audio (red & white ends) & video (yellow end) Phone cord A Phone splitter Coaxial RF cable for audio & video Power cord and Cable Bag Coaxial RF cable for audio & video B IR (infrared) Control cable RF splitter (splits your incoming cable signal to enable dual tuner if you have a cable box) Serial Control cable the cable from the wall Connect to the RF splitter You may need to purchase additional cables (e.g. Composite A/V or S-Video) depending on your home equipment. Connect your cable source to the RF splitter’s IN or INPUT jack. Note: If the cable from the wall is connected to your cable box, remove it and connect it to the RF splitter as shown. Cable Box Audio/Video Out RF Out RF In Connect your cable box to the DVR Connect a Composite A/V cable (red, white, and yellow) from the cable box’s Audio/Video OUT jacks to the DVR’s Audio/Video IN jacks. TiVo® DVR Connect to the TiVo® service: Network OR Phone the RF splitter to your Connect cable box and the DVR Your TiVo DVR needs to connect to the TiVo service to receive program listings, service updates, and other information. Choose how your DVR will connect: Network or Phone Connect two RF Coaxial cables to the RF splitter’s OUTPUT jacks. Network Choose this option if you have a home network with a broadband Internet connection. Use the connection that works with your type of home network: Wired or Wireless separately) from your home network to the TiVo DVR’s Ethernet jack (the upper jack pictured here). Then connect one of the cables to the RF IN jack on your cable box, and the other to the CABLE RF IN jack on the DVR. Wired (Ethernet) – Connect an Ethernet cable (sold Connect all cables from the OUT jack of one device to the IN jack of the next. Connect your TV OR Wireless – Connect a compatible wireless USB network adapter (sold separately) to one of the DVR’s USB ports. The TiVo® Wireless USB adapter pictured here is available at www.tivo.com/store. Television Phone Use the provided phone line splitter if the DVR is sharing the wall jack with a telephone. R L VIDEO Antenna In Connect a Channel Changing cable – Choose one from cable bag B The DVR uses one of these cables to tell your cable box when to change the channel. Use the Serial Cable if: Use the IR Cable if: you have a Motorola/General Instruments DCT2000 series cable box with a serial (data) port: you have any other kind of cable box, or you tried the Serial cable and it didn’t work with your cable box. Plug the other end into the CHANNEL CHANGING/SERIAL jack (the upper control jack) on the back of the DVR. Then continue with Step below. a IN Never connect OUT to OUT or IN to IN. Alternate: If your TV doesn’t have Composite A/V (red, white, and yellow) input jacks, connect a Coaxial RF cable from the RF OUT jack on the DVR to the Antenna In jack on your TV. Then set the Channel 3/4 switch on the back of the DVR, and tune your TV to the same channel. OUT OUT Positioning the IR cable on your cable box The IR cable’s emitters beam infrared channel change signals to the IR sensor on your cable box–just like a remote control does. Place the emitters in front of the cable box’s IR sensor (one on top of the cable box and one on bottom). Be sure both emitters stick out about 1 ½ inches directly in front of the IR sensor. Use the adhesive strips provided to keep them in place. If you’re not using the Serial cable, plug the purple end of the IR cable into the CHANNEL CHANGING/IR jack (the lower control jack) on the back of the DVR. Plug the Serial cable into the 9-pin Serial (Data) jack (like the one below) on the back of your cable box. OUT Connect a Composite A/V cable (red, white, and yellow) from the DVR’s OUT jacks to your TV’s Audio/Video INPUT. INPUT Choose this option if you don’t have a home network with a broadband Internet connection. Connect the provided phone cord from the DVR to a nearby wall jack. RF splitter Cable Box How do I find the IR sensor on my cable box? Then go to Step a for positioning the other ends of the IR cable on your cable box. The IR sensor on the front of your cable box is a tiny round bulb. If you shine a flashlight into the dark plastic “window,” you can see it. Here are some common cable box models: Plug in the DVR’s power cord. General Instruments/ Motorola DCT2000 Series (newer) General Instruments/ Motorola DCT5000, DCT6000 Series General Instruments/ Motorola DCT2000 Series (older) Pioneer Voyager 3000 Scientific Atlanta Explorer 4200 Scientific Atlanta Explorer 2100 Lights on the front panel show that it’s powered on. Tune your TV (if necessary) to see the Welcome screen Indicates the approximate position of the IR Sensor Turn on your TV. Tip: If you don’t see the Welcome screen, use the Input, Source, or TV/Video button on your TV remote or TV to select the correct audio/video source. Press the button until you see the Welcome screen. Alternate: If you used a Coaxial RF cable in Step , tune your TV to the same channel (either 3 or 4) that the CHANNEL 3/4 switch on the back of the DVR is set to. When you see the Welcome screen, you’re ready to begin Guided Setup, which customizes the DVR for your home. If you need help, see the Troubleshooting chapter in the Viewer’s Guide or visit www.tivo.com/setup. Record Two Shows at Once Your cable box receives both basic cable channels (typically 1-99) and digital cable channels (typically 100 and above). When you connect the RF splitter as shown in Step above, you are connecting basic cable channels directly to the TiVo DVR, and digital cable channels to the cable box. Digital cable channels are encoded and need the cable box to decode them. Because the cable box decodes and sends only one digital cable channel at a time, the TiVo DVR can record only one digital cable channel at a time. The TiVo DVR can record two basic cable channels at the same time, or one basic and one digital cable channel at the same time. To learn more about Dual Tuner, see the Tours in Chapter 1 of the Viewer’s Guide. Need some help? Turn this poster over for some troubleshooting tips. Check out the Troubleshooting chapter in the Viewer’s Guide for more help with connecting your TiVo DVR, completing Guided Setup, and using the TiVo service. If you have more questions, visit www.tivo.com/support to find the Getting Started Guide, Help Forums, Guided Troubleshooting, Frequently Asked Questions, and more. www.tivo.com/support
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : No Page Count : 2 Page Mode : UseOutlines Page Layout : SinglePage XMP Toolkit : XMP toolkit 2.9.1-13, framework 1.6 About : uuid:95f3fe9c-8b37-4db6-85c0-704ecd775a0d Producer : Acrobat Distiller 7.0 (Windows) Creator Tool : Adobe Illustrator CS2 Create Date : 2006:01:27 10:33:34-08:00 Modify Date : 2006:12:07 16:08:59+05:30 Metadata Date : 2006:12:07 16:08:59+05:30 Thumbnail Width : 188 Thumbnail Height : 256 Thumbnail Format : JPEG Thumbnail Image : (Binary data 21664 bytes, use -b option to extract) Document ID : uuid:B369D9435D8FDA11B75EAE2ABE12B820 Instance ID : uuid:5addf667-bd0e-4a8e-8f19-6bfcfd277acd Derived From Instance ID : uuid:B269D9435D8FDA11B75EAE2ABE12B820 Derived From Document ID : uuid:3926F582413FDA119C89D88EB3F3E08A Format : application/pdf Title : TiVo Series2 Dual Tuner DVR Start Here poster Creator : Business User Author : Business UserEXIF Metadata provided by EXIF.tools