Toastmaster Microwave Oven Tc14A Users Manual
TC18A to the manual 2dca0f94-0490-4d1e-937e-aab1020ebeb0
2015-02-05
: Toastmaster Toastmaster-Microwave-Oven-Tc14A-Users-Manual-397615 toastmaster-microwave-oven-tc14a-users-manual-397615 toastmaster pdf
Open the PDF directly: View PDF 
.
Page Count: 4
| Download | |
| Open PDF In Browser | View PDF |
TC14A/TC18A Domestic and Std. Export English P/N 39289 Rev. E V1 5/00 Middleby Cooking Systems Group 1400 Toastmaster Drive Elgin, IL 60120 (847)741-3300 FAX (847)741-4406 Conveyor Toaster Models TC14A, TC18A OWNER'S OPERATING AND INSTALLATION MANUAL © 2000 Toastmaster, A Middleby Company. is a registered trademark of Toastmaster, A Middleby Company. All rights reserved. I. DESCRIPTION AND SPECIFICATIONS A. Component Location The major components of the toaster are shown in Figure 1 below. Figure 1 4. Entry rack 5. Conveyor 3. Crumb tray 2. Conveyor speed control knob 1. Product selection knob 6. Return tray B. Component Function (see Figure 1) 1-2. Toaster control knobs - see Section III, Operation. 3. Crumb tray - Collects crumbs from the toasted product. The tray can be removed for cleaning. 4. Entry rack - Loaded with the bakery product to be toasted. The product then slides onto the conveyor. The entry rack can be removed for cleaning. 5. Conveyor - Transports the bakery product through the toaster, between the top and bottom heating elements. 6. Return tray - Collects the toasted product. The tray can be removed for cleaning. C. Operating and Electrical Specifications Pre-Heat Time: 20 minutes Electrical Specifications/TC14A toaster models: TC14A74. 120V, 50/60 Hz, 1 Ph, 1.7kW, 14.3A, NEMA 5-20P plug. TC14A63. 208V, 50/60 Hz, 1 Ph, 1.8kW, 8.6A, NEMA 6-15P plug. TC14A66. 240V, 50/60 Hz, 1 Ph, 1.8kW, 7.5A, NEMA 6-15P plug. Electrical Specifications/TC18A toaster models: TC18A63. 208V, 50/60 Hz, 1 Ph, 2.2kW, 10.5A, NEMA 6-20P plug. TC18A66. 240V, 50/60 Hz, 1 Ph, 2.2kW, 9.1A, NEMA 6-20P plug. NOTE Electrical wiring diagrams are provided at the back of this Manual. WARNING: IN CASE OF FIRE Disconnect the toaster from its power source IMMEDIATELY. This allows the unit to cool, making it easier to put out the fire. WARNING FOR YOUR SAFETY DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS OR LIQUIDS IN THE VICINITY OF THIS OR ANY OTHER APPLIANCE WARNING IMPROPER INSTALLATION, ADJUSTMENT, ALTERATION, SERVICE OR MAINTENANCE CAN CAUSE PROPERTY DAMAGE, INJURY OR DEATH. READ THE INSTALLATION AND OPERATING INSTRUCTIONS THOROUGHLY BEFORE INSTALLING OR SERVICING THIS EQUIPMENT. WARNING DO NOT OPERATE THE CONVEYOR TOASTER ON EITHER OF ITS SIDES, ON ITS REAR SURFACE, OR WITHOUT LEGS. PREMATURE FAILURE OF THE HEATING ELEMENTS WILL OCCUR. WARNING DISCONNECT THE TOASTER FROM ITS ELECTRICAL POWER SUPPLY BEFORE CLEANING OR SERVICING. CAUTION Using any parts other than genuine Toastmaster factory parts relieves the manufacturer of all liability. IMPORTANT Contact your authorized service agent to perform maintenance and repairs. A service agency directory is supplied with your toaster. IMPORTANT Toastmaster (manufacturer) reserves the right to change specifications and product design without notice. Such revisions do not entitle the buyer to corresponding changes, improvements, additions or replacements for previously purchased equipment. RETAIN THIS MANUAL FOR FUTURE REFERENCE This manual provides detailed information for the installation and operation of your toaster. It also contains information to assist the operator in diagnosing problems in the event of a malfunction. This manual is an important tool for the operator and should be kept readily available. II. INSTALLATION B. IMPORTANT IT IS THE CUSTOMERS RESPONSIBILITY TO REPORT ANY CONCEALED OR NON-CONCEALED DAMAGE TO THE FREIGHT COMPANY. IMPORTANT THE ELECTRICAL CONNECTION TO THE TOASTER REQUIRES A CIRCUIT BREAKER/FUSED DISCONNECT. ELECTRICAL SPECIFICATIONS ARE LISTED ON THE SERIAL PLATE (SHOWN IN FIGURE 3), AND IN THE ELECTRICAL SPECIFICATIONS ON PAGE 1 OF THIS MANUAL. A. Assembly 1. Thread the 4 (102mm) legs into the four holes on the bottom of the toaster. See Figure 2. Then, place the toaster in the desired location. 2. Install the entry rack and crumb tray into the front of the toaster, as shown in Figure 2. Electrical Utility Connection CONSULT ALL APPLICABLE NATIONAL AND LOCAL CODES FOR FURTHER ELECTRICAL CONNECTION REQUIREMENTS. 1. Figure 2 - Basic assembly and front-exit configuration Before proceeding with the electrical connection, check the following: a. Check that the electrical supply matches the toasters requirements. Refer to the toasters serial plate (Figure 3) and to the Electrical Specifications on Page 1. b. Check that the appropriate receptacle is available for the power cord plug. Entry rack hanger rods fit into holes on toaster body WARNING ENSURE THAT BOTH THE CIRCUIT BREAKER/FUSED DISCONNECT AND THE PRODUCT SELECTION KNOB ARE IN THE OFF (0) POSITION BEFORE PROCEEDING. WARNING ENSURE THAT ANY PACKING MATERIAL RESIDUE HAS BEEN REMOVED FROM INSIDE THE TOASTING CHAMBER. 3. Return tray slides underneath toaster Insert the power cord plug into its receptacle. III. OPERATION Legs (4) thread into holes in bottom of toaster 3. A. Crumb tray slides into opening in front of toaster Location and Function of Controls This section provides a basic description of the toaster controls, their location, and the functions they perform. The operator MUST be familiar with the controls. Refer to Figure 4. TOASTERS INTENDED FOR FRONT-EXIT OPERATION ONLY: Figure 4 Position the return tray underneath the toaster, as shown in Figure 2. Note that the return tray extends past the FRONT of the toaster during front-exit operation. 4. TOASTERS INTENDED FOR STRAIGHT-THROUGH, REAREXIT OPERATION ONLY: Remove the CENTER screw from the rear panel of the toaster, as shown in Figure 3. Push the rear panel forward into the toaster. Position the return tray underneath the toaster as shown in Figure 3. Note that the return tray extends past the REAR of the toaster during rear-exit operation. Figure 3 - Electrical connection and rear-exit configuration 1. Product selection knob 1. 2. Adjust panel Serial plate 1. Remove screw 2. 2. Conveyor speed control knob Product Selection knob When set to TOAST ( ), switches on the conveyor, upper heating element(s), and lower heating element(s). When set to OFF (O), switches off the conveyor and all heating elements. When set to BUNS/BAGELS ( ), switches on the conveyor and lower heating elements ONLY. Conveyor Speed Control knob Adjusts the speed of the conveyor. This controls the amount of toasting that the bakery product receives. Return tray slides underneath toaster 1 is the minimum speed setting, which produces a darker toasting of the bakery product. 9 is the maximum speed setting, which produces a lighter toasting of the bakery product. B. Operation Procedure C. Shutdown Procedure 1. Restore electrical power to the toaster at the circuit breaker/fused disconnect. 1. Switch the Product Selection knob to the OFF (O) position. 2. 2. Switch the Product Selection knob to either TOAST ( Disconnect electrical power to the toaster at the circuit breaker/ fused disconnect. 3. Allow the toaster to cool. D. Clearing Jams BAGELS ( ) or BUNS/ ), depending on the product to be toasted. 3. Allow the toaster to pre-heat for at least 20 minutes. 4. Adjust the toasting time (if necessary) by turning the conveyor speed control knob. 5. Load the entry rack with the bakery product to be toasted. The product will slide off the entry rack and onto the conveyor. IMPORTANT If the Product Selection knob is set to BUNS/BAGELS ( ), load WARNING NEVER INSERT YOUR HANDS INTO THE TOASTING CHAMBER TO CLEAR A JAM. SERIOUS INJURY MAY RESULT. CAUTION NEVER use a plastic object to clear a jam. If the toaster is not completely cool, damage to the toaster may result. the bakery product CUT SIDE DOWN for proper toasting. Refer to CAUTION When clearing a jam, use care to avoid damaging the heating elements. Figure 5. 1. Switch the Product Selection knob to the OFF (O) position. 6. After toasting, remove the product from the return tray. 2. 7. During inactive periods, switch the Product Selection knob to the Disconnect electrical power to the toaster at the circuit breaker/ fused disconnect. 3. Allow the toaster to cool. BUNS/BAGELS ( ) position. This leaves only the lower heating CAUTION - HOT SURFACES DO NOT ATTEMPT TO CLEAR THE JAM UNTIL THE TOASTER HAS COOLED THOROUGHLY. elements on, allowing a quicker recovery to normal toasting temperatures. 4. Carefully clear the jam using a long object as a probe. This object should preferably be made of wood, which is less likely to damage the heating elements. E. Daily Cleaning Figure 5 Product selection knob in BUNS/ BAGELS position Load buns/bagels CUT SIDE DOWN for proper toasting WARNING WHEN CLEANING THE TOASTER, NEVER APPLY ENOUGH LIQUID TO STAND IN PLACE ON THE UNIT. DO NOT SPRAY, RINSE, OR SUBMERGE THE TOASTER. EXCESSIVE MOISTURE IN THE UNIT WILL CAUSE A SEVERE ELECTRICAL HAZARD AND MAY OTHERWISE DAMAGE THE TOASTER. CAUTION DO NOT clean your toaster using abrasive cleaners or pads. Both will scratch and dull the finish. 1. With the conveyor running, use a brush to clean any crumbs off the conveyor into the crumb tray. 2. Switch the Product Selection knob to the OFF (O) position. 3. Disconnect electrical power to the toaster at the circuit breaker/ fused disconnect. 4. Allow the toaster to cool. CAUTION - HOT SURFACES DO NOT TOUCH HOT SURFACES ON THE TOASTER, OR REACH INTO THE TOASTING CHAMBER, UNTIL THE UNIT HAS COOLED THOROUGHLY. 5. Wipe the exterior of the toaster with a sponge or cloth soaked in hot or warm detergent water. Wipe with a clean, damp cloth to remove the excess detergent, and then wipe again to dry the toaster. 6. Remove the crumb tray and the return tray from the toaster, and empty them. Wash the trays in warm detergent water, and rinse them. CAUTION Never remove the crumb tray while the conveyor is moving. 7. Remove the entry rack from the toaster. Wash the rack in warm detergent water, and rinse it. 8. Towel the trays and entry rack dry. Reassemble all parts onto the toaster. Wiring Diagram Model TC14A74 120V Toasters TOP ELEMENT BTM ELEMENT 1 FAN BTM ELEMENT 2 MOTOR PRODUCT SELECTION SWITCH TERMINAL BLOCK GND Wiring Diagram Model TC14A63, -66 208V and 240V Toasters CONVEYOR SPEED CONTROL TOP ELEMENT BTM ELEMENT 1 FAN BTM ELEMENT 2 MOTOR PRODUCT SELECTION SWITCH CONVEYOR SPEED CONTROL TERMINAL BLOCK GND Wiring Diagram Model TC18A63, -66 208V and 240V Toasters TRANSFORMER 230V p 115V s TOP ELEMENT 1 TOP ELEMENT 2 FAN BTM ELEMENT 1 BTM ELEMENT 2 MOTOR PRODUCT SELECTION SWITCH OFF CONVEYOR SPEED CONTROL TERMINAL BLOCK GND Switch Configuration All Model TC14A and TC18A Toasters TRANSFORMER 230V p 115V s TOAST BUNS/ BAGELS A Middleby Company Toastmaster 1400 Toastmaster Drive Elgin, IL 60120 USA (847)741-3300 FAX (847)741-4406 Middleby Corp 24-Hour Service Hotline 1-800-238-8444 www.middleby.com
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.2 Linearized : No Page Count : 4 Create Date : 1910:00:51 00:83:23 Producer : Acrobat Distiller 3.0 for WindowsEXIF Metadata provided by EXIF.tools