Tong Lung Metal Industry PL1-B Electronic BLE Deadbolt User Manual
Tong Lung Metal Industry Co.,Ltd. Electronic BLE Deadbolt
User Manual
| Download: |  |
| Mirror Download [FCC.gov] | |
| Document ID | 3779296 |
| Application ID | JQ8BSTbGXKgEu5EJYoR+Fw== |
| Document Description | User Manual |
| Short Term Confidential | No |
| Permanent Confidential | No |
| Supercede | No |
| Document Type | User Manual |
| Display Format | Adobe Acrobat PDF - pdf |
| Filesize | 410.23kB (5127868 bits) |
| Date Submitted | 2018-03-13 00:00:00 |
| Date Available | 2018-03-14 00:00:00 |
| Creation Date | 2018-01-23 09:27:12 |
| Producing Software | Corel PDF Engine Version 17.0.0.491 |
| Document Lastmod | 2018-01-23 09:27:12 |
| Document Title | User Manual |
| Document Creator | CorelDRAW X7 |
| Document Author: | Kai Hsu_許世凱 |
Model I PL1-B Brand 1 EZSET
Electronic BLE Deadbolt
Please download “BLE Smart Look”
on } Google Play or 0 App Store.
Once the installation is completed, turn on the device’s
Bluetooth and open “BLE Smart Lock" App to begin pairing.
BLE Smart Lock
My lock
H—w ai— iiiiii lit Walt for the page to scan for Bluetooth locks
In range.
Locks found will be shown on screen.
Select the lock with default name of
“BLE Lock-PL1" to continue.
e tcalcctt ligurr
ii.
a BLE LockrFLI
Note: Bluetooth scanning time may vary depending
on Android manutacturers.
Attention: ”BLE LockrF'L1' shown in black tont means
the unit is available
Paired lock names will be shown in red.
< Connect to Device
:‘rLk L int-m
6 Chinese characters are not supported.
Please use alphanumeric characters only.
UserNanle
Tony Attention: The factory derault programming code
is: OrOrDrO
lfthe programming code has been changed
Programmlng Code
0 ° - s by user. please enter the newly changed
tack Name programming code
Home
O iimrwflamgmmmummma
CONNECT
Enter lock information to proceed with pairing.
The lack is not set
CDNFlRM
Attention:
When “The lock is not set" message
appears
Please tollow the instructions tor
door handing - so that your look
knows it it ls used on a left hand or
right hand door Then proceed with
pairing.
ConneLtlon Note
Always makestn psoriasis um
dlstzmx tren- Your BLE lock
CANCEL CONFlRM
Home
Home
Ptlsltrbtlttoll Unlock
Signal strength
Motor Detect Error
connnn
Attention:
When “Motor Detect Error' message appears
Bluetooth pairing must be carried out while the
luck is in unlocked State.
Please first unlock. then proceed with pairing
process
Follow the tips, touch lock with mobile phone
and select “OK".
This step calibrates the sensor proximity
Please ensure the pairing process is done with
mobile phone as close to the look as possible
Failing to do so will cause sensordistance error and
increase safety detection warning area
Bluetooth paring is completed when the lock
setting screen displays the following:
{at Administrator Function Settings
Home Lock Name (Set by user)
( Go Back
Lock / Unlock
Lock Battery Level
FushrButton Unlock On I 0" (Default on)
Bluetooth signal strength between
Smart phone and look
ockl Unlock With Paired Mobile Phone
My locks
Open BLE Smart Lock App and select paired
lock.
leir— art'— w
Choose a lack ti) contours
Attention: The working range between the lock and
your Smanphone is around 16 leet (5m)
u, . links,
’e‘ Nomalvatred) S
Home Unlocked Icon
The GREEN (unlocked) icon means the current status
of the lock is ”UNLOCKED".
Home
Pushrbtllton unlock
4)).
signal strength
Locked Icon
The ORANGE (locked) icon means the current status
of the lock is ”LOCKED".
Fushroulton Unlock
o) e
Slgnel strength
Model I PL1-B Brand 1 EZSET
Bluetooth Authentication
Press "Back” key and exit App.
Make sure your smart phone is within 12" (30cm) or the lock. then push the top button
on your lock to proceed with Bluetooth authentication
Once aulhenticated, the mobile phone will send 'Unlocked” notification and unlock.
Bluetooth authentication time may vary between differentAndroid manulacturers and should
not take longer than 5 seconds.
Attention: lt authentication rails. mobile phone will send “Unlock distance error" nolitication.
Please adjust the distance between mobile phone and lock to within
12" (30cm). and then try again.
Safety etection
When the smart phone is within 20" (50cm) or the lock and the connection has been established
a in seconds countdown will begin on the lock
it user does not unlock within to seconds by pressing the “Bluetooth” outton. five short beeps
will sound warning the user that currently mobile phone is within connection distance and they
should move out of the 20" (50cm) connection range.
Outside distance
20" (50cm)
Inside distance
20" (50cm)
Administrator Functio s
Load paired devices list
Select the Setting icon on the top right corner or the locking setting screen to view
paired Bluetooth devices
Administrator's name appears in red. All other users‘ name appear in black.
to devices max. including the administrator)
Devices E’i
u any
n ramiiyu
D Farnilyaz
Home
Horne
Pusnabultan Unlock
signal strength
Devices
tony
'3 “ml“ any i.
D Famtlyaa Famllyal 1207 '4 or
tea 1707 M 2:
El ‘05 lDS oar ‘50s
tony tznr isia
lDS our ipii
ios 1207 is in
Delete Paired Device From List
On “Paired Devices" screen. select the “Edit" button on the top right corner and “Delete" icon
will appear
Arter pressing delete icon. confirm by pressing “OK" on the confirmation screen to delete
Devices lZi
a ran
a ramiiyu
D FamiIYrZ
El pantry:
El ios
Delete device Flosy
ElElElEl
cancst
connw
Review Usage Log
Select administrator device name (in red) to review usage log.
Attention: Unlocks made with passwords will show in log as “Code". but no date and time information will be recorded.
REGULATORY COMPLIANCE
this product caniplnshiihsandsrdsssttolnhsd bylmlnllwlngrltgulalmy bodiss
Ihdlfil Communflwnx Camillsslnll (rcci - industry Canada
Pct:
this flwlummvlluwm Part is armed Rulls
Operallan is suhect u the toilwlily Mo donations
( t lthn dam nlaylwt uun hernitul int. ulandt 2 llnlsdwlu nun and any intensnrcc rrpnysd, includnp lnllfllunol that nay csuro undmnd opt-aim
this equipment has puntesudahdrcund apnpry uththa iinits lnrnClnss adgtai devicepuratantta Pan tenths rcc ttuips
those llrrlnxarl memento prcyidonaporapi- orctadtpnaaainrt harnitvi int ce ina noderuai installiomi
this equipmenl generates, use. and can node radio heguency energy an n no installed mid wed ln madame wllh lite lnstmnllnM. mnry cause hanntui inierrerence to radio ccnnunpstcns
Huwtmr literals no guarantee tratintsnsrenpp wlll notnmlrlll avamwlarlrlstallatwn
irthis .pppmht pp.s out. hpnrui intpnpnnp. tpndaortnpvisan n:'pttnn,wnlm pin badptsinhutpytunng th
lnterierulce hypneprhcrcptlhe lollwmg neaaires
tRlamlil onlocats IM receiving anhnns
, increase the separation between the equlpmentand recover
-opnrnct tm ecunrcnt into an twist on a ordiit dmarsnt iron that to which the rscnycr is wnnudnfl
-cohsuitrhe dealer or an erpehenced radiprrv technioan rm help
ipnipnt or and on. th. user is .ncpong.d to try to normal the
IMPORTANT t
Chang" or niotiricaticnx not uprettly appnmtt by the rranutactunr wulfl rout the user avthcnty to operate it» egvtptnont
(o I
T ubles otl
Problem
Unable to find locks on the
scan page.
s ble Causes
(1) Bluetooth not lumed on
(2) Batteries are low or dead
Act
(1) los system please manually
enable Bluetooth function.
(2) Change batteries
“The lock is not set'
message appears during
pairing process
Door handing has not been
sel
Please refer to user manual and
set door handing first belore
attempting to pair with the lock.
“Motor Detect Error"
message appears during
pairing process.
Luck has not been unlocked
Please turn lock bolt to
”Unlocked” Stale/slalus. then try
the pairing process again
“Lock Has Been Reset"
message appears when
entering Settings screen in
AW
(1 ) The lock has been reset by
other users
(2) User has been deleted by
administrator
(1) Please tum look bolt to
“Unlocked” state/status. then
try the pairing process again
(2) Please consult with the
administrator
Unable to perrorm one push
unlock.
(1) Mobile phone is too rar
item the lock
(2) PushaButlon unlock is
not enabled
(3)Lock has been reset
(1) Please make sure the mobile
phone is within 12" (30cm)ot
the lock lor one push unlock.
(2) Please enterthe settings
page within the App and
make sure
“PushaButton unlock" is
enabled.
(3) Please enter the settings
page within the App and
make sure the lock had not
been reset
Safety detection still beeps
warning at distance over
3 feet (1m).
Mobile phone was not paired
correctly by touching the lock
during the pairing process.
Please reset luck or contact
administrator and delele
currently user, then try pairing
the lock again to establish
sarety distance.
ELECTRONIC DEAD BOLT
Determine which latch mounting method will be used
and make necessary adjustments.
No adjustment required for square latch face plate.
a. Use a flat screwdriver to separate the face plate.
b. Snap selected latch face onto back plate.
Installation Guide
Drive-in Installation
Remove original latch faceplate.
Align the drive-in sleeve as illustrated
and snap into the latch case.
«a
A WARNING
Do not use an electric screwdriver during installation.
& WARNING
This Manuiacturer adVises that no lock can provide complete security by itselr
This lock may be deieated by reroilale or technical means, or evaded by entry elsewhere on the property.
No iecit can substitute lor caution, awareness dl your envnonment, and common sense
Builder‘s hardware is available in multiple perrormance grades to suit the application
in order to enhance security and reduce risk, you should consult a quaiiried locksmith or other security professional.
Drivesin Latch
n Backset Determination
Backset is a distance from door edge to centre of
hole on door face.
Adjustable latch fits both backset of 2-3/8" (60 mm)
and 2—3/4" (70 mm).
l .
are
a Mark the Door with Template
Select the height and backset as desired on the
door face: use the TEMPLATE as an indication to
mark the centre of the circle on the door face and
the centre of the door edge.
a Drill Holes
n Install Latch
Using the marks as a guide to drill a hole
02-1/8" (54 mm) through the door face for the lockset,
then a hole of 61" (25.4 mm) for latch.
Part Description Quantity Part Description
A Key 2 E Strike Plate 1
B Cylinder 1 F Mounting Plate 1
c Deadbolt Keypad Assembly 1 G Receiver Assembly 1
I] Deadhnlt Latch I H Battery Cover 1
I DVIVFHI’I Sleeve lOptmnall t
Insert the latch and ensure it is parallel to the door face.
HARDWARE SCREWS CONTE
a” 0
Machine Screws Qty. 3
You need to stay this
way up when inserting
the latch.
flcaa/
Wood Screws Qty. 5
0 iii Itlltlilllltlllillltlitt‘ fl
Chisel 5/32" (4 mm) deep along the outline to allow the
0 faceplate to be aligned with the door edge.
Deadbolt Chassis Screws Qty. 2
LATCH ADJUSTMENT
Determine if the latch needs to be adjusted to the273/4“ (70 mm) backset.
To adjust, rotate the latch until it stops.
Reverse the direction to return to the 2-3/8" (60 mm) backset.
Insert the latch into the door.
Use 2 wood screws to secure
latch.
Please do not fully tighten the
screws until lock is
completely installed.
Install Drive-in Latch
Drive the latch into the
hole on edge of door.
24/3" (50 mm)
2-3/ "(10 mm)
Mark the outline of the faceplate, then take out the latch.
HANGE LATC FACE a Install Strike
To identify the centre of strike: close
the door to lay the latchbolt against
the door frame.
Mark the centre line on the doorframe
exactly opposite the latch hole in the
door edge.
Install the strike plate into your door
frame and tighten With wood screws.
Measure one half of door thickness
from door stop and vertically mark
centre line of strike.
Drill 1" (25.4 mm) hole, ‘I" (25.4 mm)
deep at intersection of horizontal and
vertical line of strike.
Chisel 5/64" (2 mm) deep along the
strike outline to allow the strike to be
aligned with the doorframe.
n Install Keypad Assembly
Install cylinder into the deadbolt
keypad assembly with tailpiece in
horizontal position inserted through
hub of the latch.
Pass the IC wire under the latch to
the interior side of the door.
n Install Inside Mounting Plate
Mounting Plate
n Identify Door Handing
Face the door from the outside.
Pass the to wire through the wire hole of
the mounting plate.
Fix the mounting plate with screws.
If outside lock assembly is lopsided,
please loosen the screws to adjust its
position and tighten the screws again.
The door is left-handed if the hinges are on the left side of the door,
whereas the door is right-handed if the hinges are on the right side of the door.
Hinge
Hinge
Left-handed Right-handed
n Adjust Thumb Turn Piece
Rotate the thumb turn piece to the LEFT
at 45 degrees for right-handed doors.
Rotate the thumb turn piece to the RIGHT
at 45 degrees for leftahanded doors.
Note :The thumb turn piece is opposite
to the latching side.
(9
For rightshahded For leflsharlded
door door
m Install Receiver Module
Remove the battery cover
. . . Wood Screw
(push it up first then pull it out).
Connect the IC Wire into the back of
the receiver module.
Ensure that the deadbolt tailpiece is
engaged with turn piece, then attach
receiver module to the door with
screw.
Use the optional wood screw to
secure the receiver module to wood
doors only.
m Insert Batteries
Insert 4 (AA) 1.5 V alkaline batteries and slide the battery cover back onto the
receiver module.
Remarks:
(1)Alkaline batteries are recommended in order
to stabilize the power supply.
If you don't use alkaline, battery performance
will be reduced greatly.
(2)All settings will be retained in the memory
even if the batteries are completed dead.
FOR BACKSET 2 3/ " (70 mm)
TEMPLATE ' 7
FOR BACKSET 2-3/8" (60 mm)
Fit here on door edge
/fiik
51mm 45mm 40mm 35mm
2“ 173/4“ 179/15“ 173/3“
Mark Ell“ (25 4 mm) hole at
centre of deer edge
22-1/3" (54 mm) /
Source Exif Data:
File Type : PDF File Type Extension : pdf MIME Type : application/pdf PDF Version : 1.6 Linearized : Yes Author : Kai Hsu_許世凱 Create Date : 2018:01:23 09:27:12+08:00 Modify Date : 2018:01:23 09:27:12+08:00 Title : Has XFA : No XMP Toolkit : Adobe XMP Core 5.6-c015 84.159810, 2016/09/10-02:41:30 Metadata Date : 2018:01:23 09:27:12+08:00 Creator Tool : CorelDRAW X7 Format : application/pdf Creator : Kai Hsu_許世凱 Document ID : uuid:99a8bfa2-fe1a-4688-9d30-1bd3287617b9 Instance ID : uuid:dd4ef0f7-97ef-4f21-9a68-ba748a3c0c3c Producer : Corel PDF Engine Version 17.0.0.491 Page Count : 3 Profile CMM Type : Linotronic Profile Version : 2.1.0 Profile Class : Display Device Profile Color Space Data : RGB Profile Connection Space : XYZ Profile Date Time : 1998:02:09 06:49:00 Profile File Signature : acsp Primary Platform : Microsoft Corporation CMM Flags : Not Embedded, Independent Device Manufacturer : Hewlett-Packard Device Model : sRGB Device Attributes : Reflective, Glossy, Positive, Color Rendering Intent : Perceptual Connection Space Illuminant : 0.9642 1 0.82491 Profile Creator : Hewlett-Packard Profile ID : 0 Profile Copyright : Copyright (c) 1998 Hewlett-Packard Company Profile Description : sRGB IEC61966-2.1 Media White Point : 0.95045 1 1.08905 Media Black Point : 0 0 0 Red Matrix Column : 0.43607 0.22249 0.01392 Green Matrix Column : 0.38515 0.71687 0.09708 Blue Matrix Column : 0.14307 0.06061 0.7141 Device Mfg Desc : IEC http://www.iec.ch Device Model Desc : IEC 61966-2.1 Default RGB colour space - sRGB Viewing Cond Desc : Reference Viewing Condition in IEC61966-2.1 Viewing Cond Illuminant : 19.6445 20.3718 16.8089 Viewing Cond Surround : 3.92889 4.07439 3.36179 Viewing Cond Illuminant Type : D50 Luminance : 76.03647 80 87.12462 Measurement Observer : CIE 1931 Measurement Backing : 0 0 0 Measurement Geometry : Unknown Measurement Flare : 0.999% Measurement Illuminant : D65 Technology : Cathode Ray Tube Display Red Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Green Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract) Blue Tone Reproduction Curve : (Binary data 2060 bytes, use -b option to extract)EXIF Metadata provided by EXIF.tools