Tong Lung Metal Industry PL2-TR Touchpad Proximity Electronic Deadbolt User Manual

Download:
Mirror Download [FCC.gov]
Document ID	3741595
Application ID	0kRQ9GRRgE3Q4DPvpSJpzQ==
Document Description	User Manual
Short Term Confidential	No
Permanent Confidential	No
Supercede	No
Document Type	User Manual
Display Format	Adobe Acrobat PDF - pdf
Filesize	209.02kB (2612741 bits)
Date Submitted	2018-02-05 00:00:00
Date Available	2018-02-07 00:00:00
Creation Date	2018-01-10 13:12:26
Producing Software	Corel PDF Engine Version 17.0.0.491
Document Lastmod	2018-01-10 13:12:26
Document Title	PL2S 3合1設定說明書-PL2S-3-1英文版(A3)-20180102修改.cdr
Document Creator	CorelDRAW X7
Document Author:	Kai Hsu_許世凱

Touchpad Proximity Electronic Deadbolt
OPERATIONAL INTERFAC
USER GUIDE
Do not use any chemical liquid or lubricating oil with additives to clean the lock body.
It will damage the surface or even mainboard.
Sensing Area
To sense the RFID card to lock and unlock function
Programming Button
Programming button is for setting function.
Lock Buttons
Lock Button is for lock and unlock function.
Cylinder
To lock/unlock the Iockset by key from outside.
Washer
Prevents water from permeatlng into Iockset.
Battery Lid
TROUBLE SHOO NG
After installing the lockset and batteries, the door
can't be locked and three short beeps are emitted
when you press the lock button
The door-handing identification
process isn’t yet complete.
Referto door handing identification process
You've installed the lockset and batteries, but you
still get no response when you press any button.
Batteries were installed incorrectly
and cable connect incorrectly.
Check to see if the battery polarities have been
reversed or if the battery is dead
If so. reinstall or change the battery
it not, please check to see ifthe cable is
properly connected
When you are in the doorrhanding identitying
process, you get the red light llashing three times,
and three short beeps.
Wrong doorrhandlng or change or
the door-handing in the memory
Press the R button to restore the system to
factory default setting and re-execute
doorrhanding identitying process
Although you succeeded in the first execullon otthe
door—handing identlfying process the latch still
doesn‘t work
(i.e. You can leel the motor attempting to run.)
Low battery
Replace with new alkaline batteries
The door can be locked normally, but when you try
to unlock it, you hear three short beeps and the lock
wont unlock when you enter the user code and
press the lock button
The funcllonlng ot the
micm—swltch is abnormal.
Call our customer service department
While the door is locked, you hear the latch bolt
coming out when you press the to lock the door;
however, three short beeps are emitted
Conversely, while the door is open, no beeps
(‘l t The depth of the latch bolt hole
is insufficient.
(2) The latch bolt ls not aimed at the
opening at the strike.
(1) Dig the latch bolt hole torthe strike deeper.
The minimum depth is 1" (2 5 cm)
(2)Adyust the strike to the appropriate position
Sllde the lid to change the batteries.
Battery Holder
FourAAt1.5 V) alkallne batterles.
R Button (Reset)
Restore delault settlngs.
©®®®®®®®
Tu rn-piece
To lock/unlock the Iockset from inside.
OPERATING INSTRUCTIONS
Keep the door open while programming to avoid being locked out accidentally.
The lock contalns one factory—preset user code but can be programmed to store up to a total of thirty additional unique user codes.
Codes can be added and deleted at any tlme. For flrst—time programming, use factory default programming code.
lt’s recommended to change the default programmlng code and default user code rlght after you install the lock.
Every programming step should be done within 6 seconds.
Operation Indicator Sounds and Lights
Sounds Lights Meaning
1 Beep Successful Operation
2 Long Beeps Successful Programming
3 Beeps Operation Error
5 Beeps Code lnput Error; System Shuts Down
10 Rapid Beeps Low Battery Power
3 Long Beeps Default Setting Restored
Lock button flashes slowly ln Programming Mode
are emitted when looking the latch bolt.
WARRAN
The manufacturerwarrants the product to be tree trom detects in material and workmanship tor a period of 12 months trom the original date ot
purchase
liyou discover a defect in the product covered by this warranty. we will repair or replace the item at our option using new or refurblshed components
EXCLUSIONS
This warranty covers detects in manutacturing dlscovered while using the products as recommended by the manufacturer rather than occurred by
the act ot God, and damages caused by misuse, abuse, and unauthorized modification
LIMITED LIABILITY
The manulacturer will not be held llable for lnCldental or consequential losses or damages lrom any act OI God.
REGULATORY COMPLIANCE
This product complies With standards established by the following regulatory bodies
- Federal Communications commission (FCC) ~ industry Canada
FCC
This device complies With Part 15 of the FCC Rules
Operation is subyeet to the folloWing tWo conditions
( t 1 this device may not cause harmtul lnterference, and t 2 1 this device must accept any interterence recelved, including intenerence that may cause undesired operation
This eguipment has been tested and tound to comply With the limits fora class a digital devlce, pursuant to Part 15 of the FCC Rules
These limits are designed to provide reasonable protection against harmtul interierence in a residential installation
This equipment generates uses, and can radiate radio frequency energy and, lI not installed and used ln accordance With the instructions, may cause harmtul interference
to radio communications.
However. there is no guarantee that lnterference Will notoccur in a particular installation.
ltthis equipment does cause harmful interterence to radio or television reception, which can be determined by turning the equipmentott and on, the user is encouraged to
try to correct the interterence by one or more of the tollowrng measures:
- Reorient or relocate the receiving antenna.
- lncreasethe separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit difterent from that to Which the receiver is connected
~ Consult the dealeroran expenenced radio/TV technician for help
IMPORTANT !
changes or moditications not expressly approved by the manufacturer could void the user authority to operate the equipment
SETTING
8. Enable/Disable All User Codes
Default programming code (PC): 0-0-0-0 Default user code (UC): 1-2-3-4
Your new user code (U6)
The same programming code and user code cannot be accepted. Note: Auto-locking and keypad locking functions will be invalid when user codes are disabled. The lock can only be
operated by key during the time. Repeat the steps to enable the user codes again.
The lock will cease operation if unauthorized codes are entered over 5 times.
The system will unfreeze after 45 seconds. 9. Create a One-Time User Code 4—10 Digits Long
. ~ 1: . . .
1. Door Handing Identification Process
The lock needs to learn lfyourdoor is a right-handed or left-handed. Note: The one-time user code will automatically cancel after it is used one time.
Do THIS FIRST " " n " 1°- Res‘we Defau“ semflgs
Press " R "
2. Change Programming Code Note: Press the button for more than 5 seconds. the programming is reset back to the
original factory codes once you heat 3 long beeps
After restoring default settings, you must run the door handing identifying
Enter PC Q Q n Q Q Enter New PC Q process (W) again before programming any other functions.
3. Add New User Code
FID CARD REGISTRATION
. » n » . »
Note: Up to 30 sets of user codes can be saved. User codes should be 4—10 digits in length.
1. Registering the cards
»---nn»»nn»
Instruction: After the setup is complete, place the card close to the sensor (when it beeps once, the registration is complete).
Q Q n Q Q Enter the UC you want to delete Q The number "Oi” above represents the order of the card.
If the card to be registered is the third card. enter the number “03", and so on.
A maximum of 99 cards can be registered. They can be registered individually or consecutively.
5. Delete All User Codes at Once Note: The master password must be entered for the registration.
The cards may be registered individually or consecutively with a maximum of 99 cards.
If registered with over 20 cards/tags, you might experience delayed response.
2. Voiding designated cards
n-m
6. Toggle Auto-Lock On/Off
instruction: The number “01" above represents the order of the card To void the cards, please enter the order of the card
Enter PC .. .. n .. For example if the third card is to be voided, enter “03", and so on The cards may be voided indivldually
or consecutively.
Note: The master password is required to void the card.
N0“: The preset delay-time is 30 SECQHdSi you can Change the time by tollowmg instructions #7- Voided cards may be reused again after registration. The cards may be voided individually or consecutively.
Repeat the steps in 336 to cancel the auto-locking function
4. Delete an Existing User Code
Note: Auto—locking and keypad locking functions will be invalld when user codes are deleted
The lock can only be operated by key during that time
7. Set Auto-Lock Time Delay 3. Voiding all cards at the same time
Instruction: When it beeps Iche, all cards have been voided.
Note: The master password is required to void the cards. All cards may be voided at the same time.
The voided cards may be reuse again after registration.
Note: 10—99 seconds delay-time available.

---

Source Exif Data:

File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.5
Linearized                      : No
Profile CMM Type                : Lino
Profile Version                 : 2.1.0
Profile Class                   : Display Device Profile
Color Space Data                : RGB
Profile Connection Space        : XYZ
Profile Date Time               : 1998:02:09 06:49:00
Profile File Signature          : acsp
Primary Platform                : Microsoft Corporation
CMM Flags                       : Not Embedded, Independent
Device Manufacturer             : IEC
Device Model                    : sRGB
Device Attributes               : Reflective, Glossy, Positive, Color
Rendering Intent                : Perceptual
Connection Space Illuminant     : 0.9642 1 0.82491
Profile Creator                 : HP
Profile ID                      : 0
Profile Copyright               : Copyright (c) 1998 Hewlett-Packard Company
Profile Description             : sRGB IEC61966-2.1
Media White Point               : 0.95045 1 1.08905
Media Black Point               : 0 0 0
Red Matrix Column               : 0.43607 0.22249 0.01392
Green Matrix Column             : 0.38515 0.71687 0.09708
Blue Matrix Column              : 0.14307 0.06061 0.7141
Device Mfg Desc                 : IEC http://www.iec.ch
Device Model Desc               : IEC 61966-2.1 Default RGB colour space - sRGB
Viewing Cond Desc               : Reference Viewing Condition in IEC61966-2.1
Viewing Cond Illuminant         : 19.6445 20.3718 16.8089
Viewing Cond Surround           : 3.92889 4.07439 3.36179
Viewing Cond Illuminant Type    : D50
Luminance                       : 76.03647 80 87.12462
Measurement Observer            : CIE 1931
Measurement Backing             : 0 0 0
Measurement Geometry            : Unknown
Measurement Flare               : 0.999%
Measurement Illuminant          : D65
Technology                      : Cathode Ray Tube Display
Red Tone Reproduction Curve     : (Binary data 2060 bytes, use -b option to extract)
Green Tone Reproduction Curve   : (Binary data 2060 bytes, use -b option to extract)
Blue Tone Reproduction Curve    : (Binary data 2060 bytes, use -b option to extract)
Page Count                      : 2
Create Date                     : 2018:01:10 13:12:26+08:00
Modify Date                     : 2018:01:10 13:12:26+08:00
Producer                        : Corel PDF Engine Version 17.0.0.491
Author                          : Kai Hsu_許世凱
Creator                         : CorelDRAW X7
Title                           : PL2S 3合1設定說明書-PL2S-3-1英文版(A3)-20180102修改.cdr

EXIF Metadata provided by EXIF.tools