Top Victory Electronics CM785F User Manual 8

Top Victory Electronics (Taiwan) Co Ltd 8

8

Download: Top Victory Electronics CM785F User Manual 8
Mirror Download [FCC.gov]Top Victory Electronics CM785F User Manual 8
Document ID15828
Application IDhevzI8z655aq33xcfjwajA==
Document Description8
Short Term ConfidentialNo
Permanent ConfidentialNo
SupercedeNo
Document TypeUser Manual
Display FormatAdobe Acrobat PDF - pdf
Filesize28.63kB (357909 bits)
Date Submitted1998-12-11 00:00:00
Date Available1999-01-25 00:00:00
Creation Date2001-07-11 14:43:21
Producing SoftwareAcrobat Distiller 4.0 for Windows
Document Lastmod2001-07-11 14:43:21
Document Title8

Page 24
Top Victoz Electronics (Taiwan) Co., Ltd. 17" Color Monitor FCC ID. : ARSCM785F
EXHIBIT 5
User‘s Manual
User‘s Manual
Welcome
Congratulations on your purchase of an AOC monitor. Our
monitors are made to the strictest ISO-9001 standards
and we stand behind every one of them. The high
resolution and flicker free refresh rates will relieve your
eyestrain and increase your productivity. You have made
a wise investment in this monitor, and we're sure it will
deliver quality performance without straining your budget.
If you have any questions or problems with your new
monitor, visit our online technical support at
www.aoc|td.com. Now let’s start setting up your new
monitor!!
Hefore operating the monitor please read this manual thoroughly. This
rrisnual should be retained for future reference.
FCC Class B Radio Frequency Interference Statement
WARNING: (FOR FCC CERTIFIED MODELS)
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause homiful inflerference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
taming the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.
Notice:
1. The changes or modificanons not expressly approved by the party
responsible for compliance could void the usefs authority to operate the
equipment,
2. Shielded interface cables and AC. power cord, if any, must be used in
order to comply with the emission limits.
3. The manufacturer is not responsible for any radio or TV interference
caused by tmauthorized modification to this equipment. It is the
responsibilities of the user to correct such interference.
As an ENERGY STAR“9 Partner AOC International has determined that this
product meets the ENERGY STAR“3 guidelines for energy efficiency,
Warning:
To prevent fire or shock hazard, do not expose the monitor to rain or
moisture, Dangerously high voltages are present inside the monitor. Do not
open the cabinet. Refer servicing to qualified personnel only.
“Mfr M504 ‘735F
Contents
Packing list --------------------------------------------------- 3
Precautions ----------------------------------------------------- 4
Installation Instructions 5
Swivel Base ~ 5
Power cord ——- . 5
Video cable ------------------------------------------------- 6
Operating Instructions -—
General Instructions --
Front panel control —-—
How w adjust a setting
Adjusting the picture ——-—
Features ---------- 11
Green monitor 1]
Plug and pin --- 12
Technical Support (FAQ) ---------------------------------- 13
Appendix A — Specifications -------------------- . 14.15
Appendix B — Factory Preset Timing Table ——— 16
Limited Three-Year Warranty ............................ 17.13
PACKING LIST
The product package should include the following items:
1. Monitor
2. Owner's Manual
34 Power Cord
4. Swivel Base
5. Audio Cable/Microphone Cable/DC Power Cable ( For 76er only )
Plug & Play Drivers for the AOC Spectrum Series Monitors are available at
, AOC‘s Web Site: www.aoeltd.com
PRE CAUTIONS
0 Do not use the monitor near water, e.g. near a bathtub, washhowl, kitchen
sink, laundry tub, swimming pool or in a wet basement.
0 Do not place the monitor on an unstable cart, stand, or table. If the
monitor falls, it can injure a person and cause serious damage to the
appliance. Use only a cart or stand recommended by the manufacturer or
sold with the monitor. If you mount the monitor on a wall or shelf, use a
mounting ldt approved by the manufacturer and follow the kit
instructions.
0 Slots and openings in the back and bottom of the cabinet are provided for
ventilation. To ensure reliable operation of the monitor and to prowet it
from overheating, be sure these openings are not blocked or covered. Do
not place the monitor on a bed, sofa, rug, or similar surface. Do not place
the monitor near or over a radiator or heat register. Do not place the
monitor in a bookcase or cabinet unless proper ventilation is provided.
0 The monitor should be operated only from the type of power source
indicated on the label, lf you are not sure of the type of power supplied to
your home, consult your dealer or local power company.
0 The monitor is equipped with a three-pronged pounded plug, a plug with
a third (grounding) pin. This plug will fit only into a grounded power
outlet as a safety feature. If your outlet does not accommodate the three—
un're plug, have an electrician install the correct outlet, or use an adapter
to ground the appliance safely. Do not defeat the safety purpose of the
grounded plug.
0 Unplug the unit during a lightning storm or when it will not be used for
long periods of time. This will protect the monitor from damage due to
power surges
I Do not overload power strips and extension cords. Overloading can result
in fire or electric shock.
0 Never push any object into the slot on the monitor cabinet It could short
circuit parts causing a fire or electric shock. Never spill liquids on the
monitor.
0 Do not attempt to service the monitor yourself; opening or removing
covers can expose you to dangerous voltages and other hazards. Please
refer all servicing to qualified service personnel.
0 To ensure satisfactory operation, use the monitor only with UL listed
computers which have appropriate configured receptacles marked
between 100 - 240 VAC, Min. 2.5A.
INSTALLATION INSTRUCTIONS
Swivel Base
To attach the swivel base to the monitor, do the following:
0 Carefully turn the monitor on its side or upside down. ( see figure 1 )
locate the cavities at the bottom front of the monitor,
0 Insert the pegs on the swivel base into these cavities. Push the swivel base
forward until the swivel base locks in place.
0 To remove the swivel base, hold the bottom of the swivel base, then push
it out
Figure 1 Installing and Removing the Swivel Base
Power Cord
Power Source:
1. Make sure the power cord is the correct type that required in your area.
2. This monitor has a universal power supply that allows operation in either
100/ [20V AC or 220/240V AC voltage area ( No user adjustment is
required. )
3. Connect the power cord into your monitor‘s power input socket, and then
plug the other end into a 3-pin AC power outlet. The power cord may
be connected to either a wall power outlet or the power outlet socket on
your PC, depending on the type of power cord supplied with your
monitor.
Using the Right Power Cord
The accessory power cord for the Northern American region is fine wallet
plug with NEMA 5-15 style and is UL listed and CSA labeled. The voltage
rating for the power cord shall be 125 volts ACA
Supplied with units intended for connection to power outlet of personal
computer: Please use a cord set consisting of a minimum No. 18 AWG, type
SJT or SVT three conductors flexible cord. One end terminates with n
grounding type attachment plug, rated 10A, 250V, CHE-22 male
configuration. The other end terminates with a molded-on type connector
body, rated 10A, 250V, having standard CEE22 female configuration.
Video cable
Connecting the Video Cable: The monitor comes with a built-in video cable.
Plug the signal cable‘s lS-pin connector into the computer's video porn and
tighten the two screws on the cable connector.
Connecting the Power Cord: Plug the power cord into the monitor‘s AC
power socket. Then plug the power cord into a grounded AC outlet or UL-
approved power strip or the power output socket on your PC.
Cauu‘an: If the AC outlet is not grounded (with three holes), insraII the
proper grounding adapter (not supplied)
, Connecting the Microphone Cable ( 7Ger only ): Phig microphone
cable between the computer multi-media (or sound) card's microphone input
and monitor‘s microphone output.
Connecting the Audio Cable ( 7Ger only): Plug audio cable between the
computer multi-media (or sound) card's audio output and monitor's audio
mput.
Connecting the DC Power Cable ( 7GIrA only ): Plug DC power cable
between monitor to swivel base for audio power
' - comm/ran ’
run we
aunt-11.5
srsu
m cum name:
—. v
C] m:
Power Cord
EM”? vc Aunh Dulpui
Si n Cable
~‘ g" Power Swtlch -°° °"""“
7Glr 7GlIA
Figurel Connecting Cables
The 7GirA is not available till now.
Top Victory does not provide this model before submitted to FCC.
OPERATING INSTRUCTIONS
General Instructions
The power switch is located at rear side base of the monitor (See Figure 2).
Press the power switch to turn the monitor on or off. The other control knobs
are located at the base of the mommr (See Figure 3). By changing these
settings, the picture can be adjusted to your personal preferences.
- The power cord should be connected.
0 Connect the video cable from the monitor to the video card.
l To turn the monitor on, press the POWER switch to ON position. The
power indicator will light up.
0 Your monitor features a unique quick switch system which provides a
picture within seconds other the monitor is switched on.
l___|l=__=l
2 S l a
nsn Power Indtcnnr
Stun-1h ram L
Shuttle rm Y osp Mei nan...“
DN/OFF Swivel) mm: Knob fiwggygflh
* m
“mm m" ‘Powtr omen
Wm" Power Indium
7Glr 7GIrA
Figure 3 External Control Knob
Notes
. Do not install the monitor in a location near heat sources such as
radiators or air ducts , or in a place subject to direct sunlight , or excessive
dust or mechanical vibration or shock.
0 Save the original shipping carton and packing materials, as they will
come in handy if you ever have to ship your monitor,
- For maximum protection, repackage your monitor as it was originally
packed at the factory.
- To keep the monitor looking new, periodically clean it with a soft cloth.
Stuhbom stains may be removed with a cloth lightly dumpencd with a
mild detergent solution. Never use strong solvents such as thinner,
benzene, or abrasive cleaners, since these will damage the cabinet. As a
safety precaution, always unplug the monitor before cleaning it.
Front Pan el Control
- Standby power lrey :
When pressed, the monitor enters the off mode, and the LED turns orange.
Press and hold to restore normal status.
- Shuttle Knob :
The Shuttle Knob is used to control the monitor functions. Rotate to
switch functions or adjust settings. Press to select or execute a function .
- OSD Key :
The OSD Key is used to activate tlte OSD window, or to exit the OSD
window and save the settings.
Power Indicator :
Green — Power On mode.
Orange g Stand-by mode, Suspend mode, or
Off mode (Power Saving & Standby Power Off).
Swivel Base Control ( 76er only) :
- Audio Power
ON or OFF Audio Power
- Power Indicator
Green — Audio Power ON.
- Volume
Adjustable Audio volume.
How to adjust a setting
1. Press the Shuttle Knob or OSD Key ( 7Glr only ) to make the OSD
window appear. See figure 4.
Rotate the Shuttle Knob to select the desired fimction. See figure 4.
Press the Shuttle Knob again to select the function that you want to adjust.
Rotate the Shuttle Knob in change the settings of the current function.
When the OSD window is active, it shows the input signal timing. The
"H" stands for the horizontal frequency and "V" for the vertical
frequency,
6, To exit and save, either press the OSD Key ( 7Gl.r only), select the exit
function or leave the monitor alone for 10 seconds, Ifyou want to adjust
any other function, repeat steps 2-4.
MPPN
Figure4 The OSD Message
Adjusting the picture
7. The descripticn for functional control icons
7.1 CONTRAST 0
Adjust the picture contest.
7.2 BRIGHTN'ESS
Adjust the picture brightness.
7.3 H-CENTER [D :
Adjust the horizontal position of the picture.
7.4 H- SIZE 5 .
Adjust the picture’s horizontal size.
7.5 V-CENTER E) ;
Adjust the vertical position of the picture
7.6 V-SIZE CD .
Adjust the picture's vertical size.
7.7 ZOOM @ :
Adjust the picture 3 horizontal and vertical size simultaneously.
7.8 PINCUSHION H .
Adjust the pincushion and barrel .
7.9 mpnzom D :
Adjust the picture‘s trapezoid distortion.
7.10 PIN-BALANCE G :
Adjust to compensate the pincushian unbalance.
‘ 7.11 PARALLELOGRAM D :
Adjust the picture to be a rectangle.
7.12 ROTATION @ :
Adjust the picture tilt to horizontal position.
7.13 6500°Kl9300°K ( COLOR TEMPERATURE) :
The Color temperature for 6500°K is x=0i313, y=0.329 and 9300°K
is x=0.281, y=0.3|1. It presents two different color sets on the
screen. You can select 9300°K or 6500°K by pressing the Shuttle
Knob.
7.14 USERCOLOR (Red/Blue ) é :
If the 93001 normal white or 6500VK warmer white do not satisfy
your desire, properly adjust R . B GAIN controls to obtain your
optimum whiteness level.
7.15 DEGAUSS Q :
If color impurity occurs when moving or swiveling the monitor,
press the Shuttle Knob and degauss to fix the picture condinon.
7.16 MOIRE REDUCE :
Moire is the result of interference between the phosphor layout and
the video signal. In some cases, you may find the V-moire very
noticeable. Press the Shuttle Knob to enter in the morie reduce
setting. Please adjust the level to the optimum condition. Note: Too
high of in setting will cause the picture to shake,
7,17 RECALL 4) :
Press RECALL to restore the monitor to factory settings.
7.18 EXIT :
Close OSD window
10
FEATURES
Green monitor
0 The monitor has a power saving function that conforms to the VESA
DPMS standard. This feature will only work if your PC is a green PC.
This feature is similar to a screen saver, except that your monitor will turn
itself off instead of activating the screen saver
To activate this feature in Windost 95:
In Windows” 95, this feature can be activated and customized under the
screen saver setting of the display properties.
1,
Right click on the desktop and choose Properties.
1. Click on the tab that says Screen Saver. If your system supports Green
PC, there will be a section entitled “Energy Saving Features of Monitor."
If there in t a section like that, their your PC does not support Green
Monitor. The monitor will behave Just like a normal monitor, so you will
have to turn it offmanually to save energy.
In the “Energy Saving Features of Monitor" sections are two boxes,
Standby and Shut off. To activate either one, click the box next to each
OIIC.
You can specify the amount of inactive time before your monitor enters
standby mode or shuts off,
The power-saving mode can be indicated by the light-emitting diode
LED on the front panel:
-Blank
_Am- Yes
11
THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF
THERE IS NO VIDEO INPUT SIGNAL. IN ORDER FOR TI'HS
MONITOR TO OPERATE PROPERLY, THERE MUST BE A VIDEO
INPUT SIGNAL~
This monitor meets the Power Management standards as set by the Video
Electronics Standards Association (VESA) and/or the United States
Environmental Protection Agency (EPA) and The Swedish Confederation
Employees ( NUTEK ). This feature is designed to conserve electn'cal energy
by reducing power consumption when there is no video input signal present.
When there is no video input signal this monitor, following a timeout period,
will automatically switch to an OFF mode. This reduces the monitor’s
internal power supply consumption, Afler the video input signal is restored,
full power is restored and the display is automatically redrawn. The
appearance is similar to a "Screen Saver" feature except the display is
complewa off. The display is restored by pressing a key on the keyboard, or
clicking the mouse
Plug and play
Plug & Play DDCI/ZB Feature
This monitor is equipped with VESA DDCllzB capabilities according to the
VESA DDC STANDARD It allows the monitor to inform the host system of
its identity and, depending on the level of DDC used, communicate
additional information about its display capabilities. The communication
channel is defined in two levels, DDC] and DDCZB.
The DDC] is a unidirectional data channel from the display to the host that
continuously transmits EDl'D infommtion. The DDCZB is a bidirectional data
channel based on the l’C protocol, The host can request EDID information
over the DDCZB channel.
Video Cable Pln Assignments:
1. Red 5. Ground 9. NC 13. H—sync
14, v. sync / . VCLK
1L Monitor Ground 15. DDC-Serial Clock
12.DDC—SeriulData * FORDDC
12
TECHNICAL SUPPORT (FAQL
Problem 84 Question
Possible Solution
Power LED is not on
‘Check if the Power Switch is in the ON
position
‘Power Cord should be connected
No Plug & Play
‘Check if the PC system is Plug & Pla
compatible
‘Check if the Video Card is Plug & Play
compatible
‘Check if the D-15 plug pin of Video
Cable is bent
*Make sure the AOC Monitor Drivers are
installed
(AOC Monitor Drivers are available at:
www‘aocltdeom)
No picture
‘Computer Power Switch should be in the—l
ON position
‘Computer Video Card should be snueg
seated in its slot
‘The Signal Cable should be completely
connected to the computer
‘Check the color of the Power LED
indicator. If it is omnge. then the monitor
and the PC system are in powersaving
mode. You need press your keyboard or
move the mouse to reactivate the system.
Picture is fuzzy
‘Adjust the Contrast and Brightness
Controls,
Picture bounces or a wave pattern
is went in the picture
‘ Move electrical devices that may cause
electrical interference.
Monitor is stuck in “Power
Saving Mode"
‘Make sure monitor’s video cable is
properly connected to the computer.
‘lnspect monitor‘s video cable and make
sure none of the pins are bent
‘Make sure computer is operational by
hitting the CAPS LOCK key on the
keyboard while observing the CAPS
LOCK LED. The LED should either
turn ON or OFF afler hitting the CAPS
LOCK keL
Missing one of the primary colors
A (RED, GREEN, or BLUE)
‘Inspect the monitor’s video cable and
make sure that none of the pins are
bent.
13
APPENDIX A - SPECIFICATIONS FQO I D f
CRT 43.2cm(l7"), 90° deflection, 29mm neck,
0.26mrn dot pitch non-glare screen.
Viewable Image Size 40.6cm ( 1640“), diagonal
Display Color Unlimited colors
Input Signal Analog input All timing that meets scanning
frequencies
- Video - Analog k, G, B 0.7Vpp positive/75 ohm
. Sync, - Horizontal synci : Positive/Negative
v Vertical sync. : Positive/Negative
Synchronization
- Horizontal 30KHz to SSKHz automatically
- Vertical 501-11. to 1301-11 aummntically
Max. Resolution 1600 * l200
Video bandwidth IOOMHz
Factory Preset Timings : 10
User mode Timings : 9
Misconvergence
0 Center 0.3mm Max.
0 Comer 0,4mm Max.
Power Source Switching mode power supply
AC 100-240V, SOHz/60Hz full range
Operating 0"C to MPG ambient
Humidity 10% to 85% relative, non»00ndensing
Weight 16.0Kgs(Net), 19.5Kgs(Gross)
Dimensions
0 Monitor 410{W} X 41101) X 430(D)mm
0 Canon 570(W) " 53701) X 565(D)mm
Signal Cable 15 pin mini D-Suh
External Controls:
Switch 0 Power On/Off Switch
- Shuttle Knob
. Standby Power Switch
- OSD Key
0 Volume 7Ger (mix)
14
ALMA”;
Functions(OSD) 0 Contrast
o Bnghmess
. H—Center
- H-Size
o V-Centcr
0 V-Size
0 Zoom
‘ Pincushion
o Trapezoid
a Pin Balance
- anllelogram
o Rotation
o 6500°K
- Usercolor
o 9300°K
o Degauss
. Moire Reduce
0 Recall
c Exit
Plug & Play DDC l/ZB
Power management EPA , VESA DPMS
Power consumption 120 Watts Max.
Preset display area 300mm X 230 mm
Speaker (7Ger only )
- Rate power 2W
- Impedance 89
Audio (7GI}A only)
- Audio output 1 W x 2
- Frequency response lOOHz ~ ISKHz @ d: MB
. Distortion < 3%
0 Input sensitiVlty 0,9Vpp ~ l.lep
Regulations UL, CSA, FDA, FCC, TUV / GS, CE
MPRII
TCD‘92 or TCO‘95
15
The 70er is not available till now.
Top Victory does not provide this model before submitted to FCC.
7“ M I : 17-3 r —
APPENDIX B — FACTORY PRESET TIMING TABLE 9 A C H 73 b F
HORIZONTAL VERTICAL
STANDARD “350me “(£ch FREQUENCY
IBM 720 x 400 31.47KI-Iz 7on
_,_
VGA 640 x 480 3114714111 60Hz
VESA/75 640 x 430 37.5KHz 75Hz
VESA/SS 640 X 480 433th 85112
VESA/75 800 x 600 46.875KHz 75Hz
VESA/SS 800 X 600 51671011 SSH:
VESA/75 1024 x 768 60402KHz 75Hz
VESA/85 1024 x 768 68,6](Hz 851-12
VESA/GO 1600 x 1200 75.0KHz 60Hz
__,_
VESA/75 1280 x 1024 80.0KHz 75Hz
1G
LIMITED THREE-YEAR WARRANTY
for AOC Color Monitors
Including those Sold within the European Countries as Specified
AOC International warrants this product to be free from defects in material
and workmanship for a period of three (3) years after the original date of
consumer purchase. During this period, AOC International will. at its option,
either repair the defective product with new or rebuilt parts, or replace it with
a new or rebuilt product at no charge except as ‘stated below, The parts or
product that are replaced become the property of AOC International (USA)
Ltd.
In the USA to obtain service under this limited warranty, call AOC
International for the name of the Authorized Service Center in your area
Deliver the product freight pre-paid, along with the dated proof of purchase,
to the AOC Authorized Service Center. If you cannot deliver the product in
person:
0 Pack it in its original shipping container (or equivalent)
0 Put the RMA number on the address label
0 Put the RMA number on the shipping carton
O Insure it (or assume the risk of loss / damage during shipment)
0 Pay all shipping charges
AOC International is not responsible for damage to inbound product that was
not properly packaged.
AOC International will pay the return shipment charges m‘thin one of the
countries specified within this warranty statement. AOC International is not
responsible for any costs associated with the transportation of product across
international borders, This includes the international borders of the countries
within this warranty statements.
In the United States contact your Dealer or AOC International Customer
Service, RMA Department at the toll free number (800) 7754262
In Canada, Europe ( this warranty is valid in the member countries of the
European Community ). Contact your Dealer, Reseller, Distributor or the
organization where you obtained your monitor in case of problems during the
warranty period in order to receive factory level approved service. In Europe
all repairs will he done at AOC Authorized Service Centers similar to the
ones in the USA.
‘ This limited warranty does not cover any losses or damages that occur as a
result of:
0 Shipping or improper installation or maintenance
. Misuse
k . Neglect
' Any cause other than ordmary commercial or industrial application
17
O Adjustment by non-audioiized source
0 Repair, modification, or installation of options or parts by anyone other
than an AOC Authorized Service Center
Improper environment
Excessive or inadequate heating or air conditioning or electrical power
failures, surges, or other irregularities
This thrceAyeal’ limited warranty does not cover any of the product‘s
firmware or hardware that you or any third party have modified or altered;
you beat the sole responsibility and liability for any such modification or
alteration.
ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT
(INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD
OF THREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATE
OF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED OR
IMPLIED) APPLY AFTER THIS PERIOD, IN THE UNITED STATES OF
AMERICA, SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG
AN IMPLIED WARRANTY LASTS, SO THE ABOVE LIMITATIONS MAY NOT
APPLY TO YOU.
AOC INTERNATIONAL'S OBLIGATIONS AND YOUR REMEDIES
HEREUNDER ARE SOLELY AND EXCLUSIVELY AS STATED HERE AOC
INTERNATIONAL‘S LIABILITY, WHETHER BASED ON CONTRACT, TORT
WARRANTY, STRICT LIABILITY, OR OTHER THEORY, SHALL NOT
EXCEED THE PRICE OF THE INDIVIDUAL UNIT WHOSE DEFECT OR
DAMAGE IS THE BASIS OF THE CLAIM, IN NO EVENT SHALL AOC
INTERNATIONAL BE LIABLE FOR ANY LOSS OF PROFITS, LOSS OF USE
OR FACILITIES OR EQUIPMENT OR OTHER INDIRECT, INCIDENTAL, OR
CONSEQUENTIAL DAMAGE. IN THE UNITED STATES OF AMERICA, SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL DAMAGES. SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU. ALTHOUGH THIS LIMITED
WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY HAVE
OTHER RIGHTS WHICH MAY VARY FROM STATE T0 STATE,
In the United States of America, this limimd warranty is only valid for
Products purchased in the Continental United States, Alaska, and Hawaii.
Outside the United States of America, this limited warranty is only valid for
Products purchased in Canada and the member countries of the European
Union.
18

Source Exif Data:
File Type                       : PDF
File Type Extension             : pdf
MIME Type                       : application/pdf
PDF Version                     : 1.2
Linearized                      : Yes
Create Date                     : 2001:07:11 14:43:21
Producer                        : Acrobat Distiller 4.0 for Windows
Modify Date                     : 2001:07:11 14:43:21+01:00
Page Count                      : 19
EXIF Metadata provided by EXIF.tools
FCC ID Filing: ARSCM785F

Navigation menu