Top Victory Electronics CM792H 17" Color Monitor User Manual F1795

Top Victory Electronics (Taiwan) Co Ltd 17" Color Monitor F1795

users manual

Your Work Never Looked BetterF1795+USER MANUALTABLE OF CONTENTSFOR YOUR SAFETY -------------------------------------------------- 1SAFETY PRECAUTIONS -------------------------------------- 2BEFORE YOU OPERATE THE MONITOR ---------------------- 3FEATURES -------------------------------------------------------- 3PACKING LIST --------------------------------------------------- 3INSTALLATION INSTRUCTIONS --------------------------- 3CONTROLS AND CONNECTORS -------------------------- 4OPERATING INSTRUCTIONS ------------------------------------- 5GENERAL INSTRUCTIONS ---------------------------------- 5HOW TO ADJUST A SETTING ------------------------------ 7ADJUSTING THE PICTURE ---------------------------------- 7POWER MANAGEMENT FEATURE ----------------------- 9PLUG AND PLAY ------------------------------------------------ 10TECHNICAL SUPPORT(FAQ) ------------------------------------- 12APPENDIX --------------------------------------------------------------- 13SPECIFICATIONS --------------------------------------------13-14FACTORY PRESET TIMING TABLE ---------------------- 15CONNECTOR PIN ASSIGNMENT ------------------------- 15LIMITED THREE-YEAR WARRANTY -------------------------16-17Thank you very much for choosing the AOC Pure Flat Color Monitor.We recommend that you take a few minutes to read carefully through this briefbut comprehensive manual before installing and switching on the monitor.Please keep this manual in a safe place for you future reference.ENGLISHDEUTSCHFRANÇAISESPAÑOLITALIANO
1Before operating the monitor please read this manual thoroughly. This manualshould be retained for future reference.FCC Class B Radio Frequency Interference StatementWARNING: (FOR FCC CERTIFIED MODELS)NOTE: This equipment has been tested and found to comply with the limits for aClass B digital device, pursuant to Part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in aresidential installation. This equipment generates, uses and can radiate radiofrequency energy, and if not installed and used in accordance with theinstructions, may cause harmful interference to radio communications. However,there is no guarantee that interference will not occur in a particular installation. Ifthis equipment does cause harmful interference to radio or television reception,which can be determined by turning the equipment off and on, the user isencouraged to try to correct the interference by one or more of the followingmeasures:1. Reorient or relocate the receiving antenna.2. Increase the separation between the equipment and receiver.3. Connect the equipment into an outlet on a circuit different from that to whichthe receiver is connected.4. Consult the dealer or an experienced radio/TV technician for help. NOTICE1. The changes or modifications not expressly approved by the partyresponsible for compliance could void the user's authority to operate theequipment.2. Shielded interface cables and AC power cord, if any, must be used in orderto comply with the emission limits.3. The manufacturer is not responsible for any radio or TV interference causedby unauthorized modification to this equipment. It is the responsibilities ofthe user to correct such interference.As an ENERGY STAR Partner AOC International has determined that thisproduct meets the ENERGY STAR guidelines for energy efficiency. WARNING :To prevent fire or shock hazard, do not expose the monitor to rain or moisture.Dangerously high voltages are present inside the monitor. Do not open thecabinet. Refer servicing to qualified personnel only.Plug & Play Drivers for the AOC Spectrum Series Monitors are availableat AOC’s Web Site: www.aoc-europe.com
2 lDo not use the monitor near water, e.g. near a bathtub, washbowl, kitchensink, laundry tub, swimming pool or in a wet basement.lDo not place the monitor on an unstable cart, stand, or table. If the monitorfalls, it can injure a person and cause serious damage to the appliance. Useonly a cart or stand recommended by the manufacturer or sold with themonitor. If you mount the monitor on a wall or shelf, use a mounting kitapproved by the manufacturer and follow the kit instructions.lSlots and openings in the back and bottom of the cabinet are provided forventilation. To ensure reliable operation of the monitor and to protect it fromoverheating, be sure these openings are not blocked or covered. Do notplace the monitor on a bed, sofa, rug, or similar surface. Do not place themonitor near or over a radiator or heat register. Do not place the monitor in abookcase or cabinet unless proper ventilation is provided.lThe monitor should be operated only from the type of power source indicatedon the label. If you are not sure of the type of power supplied to your home,consult your dealer or local power company.lThe monitor is equipped with a three-pronged grounded plug, a plug with athird (grounding) pin. This plug will fit only into a grounded power outlet as asafety feature. If your outlet does not accommodate the three-wire plug, havean electrician install the correct outlet, or use an adapter to ground theappliance safely. Do not defeat the safety purpose of the grounded plug.lUnplug the unit during a lightning storm or when it will not be used for longperiods of time. This will protect the monitor from damage due to powersurges.lDo not overload power strips and extension cords. Overloading can result infire or electric shock.lNever push any object into the slot on the monitor cabinet. It could shortcircuit parts causing a fire or electric shock. Never spill liquids on the monitor.lDo not attempt to service the monitor yourself; opening or removing coverscan expose you to dangerous voltages and other hazards. Please refer allservicing to qualified service personnel.lTo ensure satisfactory operation, use the monitor only with UL listedcomputers which have appropriate configured receptacles marked between100 - 240V AC, Min. 2.5A.PRECAUTIONS
3BEFORE YOU OPERATE THE MONITOR FEATURES•43.2cm(17”) Pure Flat Color Monitor•Crisp, Clear Display for Windows•Recommened Resolutions: 1024 X 768 @60Hz•EPA ENERGY STAR®•Ergonomic Design (MPR II Approved)•Space Saving, Compact Case Design The product package should include the following items:1. Monitor2. Owner's Manual3. Power Cord4. Swivel Base5. Audio Cable/DC Power Cable ( For 7KlrA only ) INSTALLATION INSTRUCTIONS. SWIVEL BASETo attach the swivel base to the monitor, do the following:•Carefully turn the monitor on its side or upside down. ( see figure 1 )•Locate the cavities at the bottom front of the monitor.•Insert the pegs on the swivel base into these cavities. Push the swivel baseforward until the swivel base locks in place.•To remove the swivel base, hold the bottom of the swivel base, then push itout.Install Remove Install RemoveF1795+ 7KlrAFigure 1 Installing and Removing the Swivel BaseFEATURESCHECKING THE CONTENTS OF THE MONITOR PACKAGEINSTALLATION INSTRUCTIONS
4 POWER CORDPower Source:1. Make sure the power cord is the correct type that required in your area.2. This monitor has a universal power supply that allows operation in either100/120V AC or 220/240V AC voltage area ( No user adjustment is required. )3. Connect the power cord into your monitor’s power input socket, and thenplug the other end into a 3-pin AC power outlet. The power cord may beconnected to either a wall power outlet or the power outlet socket on your PC,depending on the type of power cord supplied with your monitor. VIDEO CABLEConnecting the Video Cable: the monitor comes with a built-in video cable.Plug the signal cable′s 15-pin connector into the computer's video port andtighten the two screws on the cable connector. (see figure 2)Caution: Don’t bend the signal cable, otherwise it will break the inner wire.Connecting the Power Cord: Plug the power cord into the monitor's AC powersocket. Then plug the power cord into a grounded AC outlet or UL-approvedpower strip or the power output socket on your PC.Caution: If the AC outlet is not grounded, install the proper grounding adapter(not supplied).Connecting the Audio Cable ( 7KlrA only ): Plug audio cable between thecomputer multi-media (or sound) card's audio output and monitor's audio input.Connecting the DC Power Cable ( 7KlrA only ): Plug DC power cablebetween monitor to swivel base for audio power F1795+ 7KlrAFigure 2 Connecting Cables1. Power Cord 4. PC Audio Output2. Signal Cable 5. DC Output3. VGA Card AdapterCONTROLS AND CONNECTORS
5OPERATING INSTRUCTIONS The other control knobs are located at the base of the monitor (See Figure 3).By changing these settings, the picture can be adjusted to your personalpreferences.•The power cord should be connected.•Connect the video cable from the monitor to the video card.•To turn the monitor on, press the stand by power switch to ON position. Thepower indicator will light up.•Your monitor features a unique quick switch system which provides a picturewithin seconds after the monitor is switched on.645F1795+ 7KlrAFigure 3 External Control Knob EXTERNAL CONTROLS1. OSD Power Indicator2. Power Indicator3. Standby Power ON/OFF Switch•Functions:( 7KlrA ONLY)4. Audio Power Indicator 6. Volume5. Audio Power ON/OFF 7. Earphone JackGENERAL INSTRUCTIONS
6 FRONT PANEL CONTROL•Standby power key :When pressed, the monitor enters the off mode, and the LED turns orange.Press again and hold to restore normal status.•Shuttle Knob :The Shuttle Knob is used to control the monitor functions. Rotate to switchfunctions or adjust settings. Press to select or execute a function .•OSD Key :The OSD Key is used to activate the OSD window, or to exit the OSDwindow and save the settings.•Power Indicator :Green — Power On mode.Orange — Stand-by mode, Suspend mode, or Off mode. SWIVEL BASE CONTROL (7KlrA ONLY ) :•Audio Power ON or OFF Audio Power•Power IndicatorGreen — Audio Power ON.•VolumeAdjustable Audio volume. NOTES•Do not install the monitor in a location near heat sources such as radiatorsor air ducts , or in a place subject to direct sunlight , or excessive dust ormechanical vibration or shock.•Save the original shipping carton and packing materials, as they will come inhandy if you ever have to ship your monitor.•For maximum protection, repackage your monitor as it was originally packedat the factory.•To keep the monitor looking new, periodically clean it with a soft cloth.Stubborn stains may be removed with a cloth lightly dampened with a milddetergent solution. Never use strong solvents such as thinner, benzene, orabrasive cleaners, since these will damage the cabinet. As a safetyprecaution, always unplug the monitor before cleaning it.
7 1. Press the Shuttle Knob or OSD Key to make the OSD window appear. Seefigure 4.2. Rotate the Shuttle Knob to select the desired function. See figure 4.3. Press the Shuttle Knob again to select the function that you want to adjust.4. Rotate the Shuttle Knob to change the settings of the current function.5. When the OSD window is active, it shows the input signal timing. The "H"stands for the horizontal frequency and "V" for the vertical frequency.6. To exit and save, either press the OSD Key, select the exit function, or leavethe monitor alone for 10 seconds. If you want to adjust any other function,repeat steps 2-4.70V: 85Hz9300 6500H: 68.8KHzContrastFigure 4 The OSD Message The description for function control LEDS1. CONTRAST Adjust the picture contrast.2. BRIGHTNESS Adjust the picture brightness.3. H- CENTER Adjust the horizontal position of the picture.4. H- SIZE Adjust the picture’s horizontal size.5. V- CENTER Adjust the vertical position of the picture.ADJUSTING THE PICTUREHOW TO ADJUST A SETTING
86. V- SIZE Adjust the picture’s vertical size.7. ZOOM Adjust the picture’s horizontal and vertical sizesimultaneously.8. PINCUSHION Adjust the pincushion and barrel9. TRAPEZOID Adjust the picture’s trapezoid distortion.10. PIN-BALANCE Adjust to compensate the pincushionunbalance.11. PARALLELOGRAM Adjust the picture to be a rectangle.12. ROTATION Adjust the picture tilt to horizontal position.13. 6500°K/9300°K( COLORTEMPERATURE )The color temperature for 6500°K is x=0.313,y=0.329 and 9300°K is x=0.283, y=0.297. Itpresents two different color sets on the screen.You can select 9300°K or 6500°K by pressingthe Shuttle Knob.14. USER COLOR( Red / Blue ) If the 9300°K normal white or 6500°K warmerwhite do not satisfy your desire, properly adjustR . B GAIN controls to obtain your optimumwhiteness level.15. DEGAUSS If color impurity occurs when moving orswiveling the monitor, press the Shuttle Knoband degauss to fix the picture condition.16. MOIRE REDUCE Moire is the result of interference between thephosphor layout and the video signal. In somecases, you may find the moire very noticeable.Press the Shuttle Knob to enter in the moirereduce setting. Please adjust the level to theoptimum condition. Note: Too high of a settingwill cause the picture to shake.17. RECALL Press RECALL to restore the monitor tofactory settings.18. EXIT Close OSD window.19. SELECT LANGUAGE Select the language you like.
9Plug & Play DDC1/2B FeatureThis monitor is equipped with VESA DDC1/2B capabilities according to theVESA DDC STANDARD. It allows the monitor to inform the host system of itsidentity and, depending on the level of DDC used, communicate additionalinformation about its display capabilities. The communication channel is definedin two levels, DDC1 and DDC2B.The DDC1 is a unidirectional data channel from the display to the host thatcontinuously transmits EDID information. The DDC2B is a bidirectional datachannel based on the I²C protocol. The host can request EDID information overthe DDC2B channel.THIS MONITOR WILL APPEAR TO BE NON-FUNCTIONAL IF THERE ISNO VIDEO INPUT SIGNAL. IN ORDER FOR THIS MONITOR TO OPERATEPROPERLY, THERE MUST BE A VIDEO INPUT SIGNAL.This monitor meets the Green monitor standards as set by the Video ElectronicsStandards Association (VESA) and/or the United States EnvironmentalProtection Agency (EPA) and The Swedish Confederation Employees (NUTEK).This feature is designed to conserve electrical energy by reducing powerconsumption when there is no video-input signal present. When there is novideo input signal this monitor, following a time-out period, will automaticallyswitch to an OFF mode. This reduces the monitor's internal power supplyconsumption. After the video input signal is restored, full power is restored andthe display is automatically redrawn. The appearance is similar to a "ScreenSaver" feature except the display is completely off. The display is restored bypressing a key on the keyboard, or clicking the mouse. USING THE RIGHT POWER CORD :The accessory power cord for the Northern American region is the wallet plugwith NEMA 5-15 style and is UL listed and CSA labeled. The voltage rating for thepower cord shall be 125 volts AC.Supplied with units intended for connection to power outlet of personalcomputer: Please use a cord set consisting of a minimum No. 18 AWG, typeSJT or SVT three conductors flexible cord. One end terminates with a groundingtype attachment plug, rated 10A, 250V, CEE-22 male configuration. The otherend terminates with a molded-on type connector body, rated 10A, 250V, havingstandard CEE-22 female configuration.PLUG AND PLAY
10TECHNICAL SUPPORT (FAQ)Problem & Question Possible SolutionPower LED is not on *Check if the Power Switch is in the ONposition*Power Cord should be connectedNo Plug & Play *Check if the PC system is Plug & Playcompatible*Check if the Video Card is Plug & Playcompatible*Check if the D-15 plug pin of Video Cableis bent*Make sure the AOC Monitor Drivers areinstalled(AOC Monitor Drivers are available at:www.AOCeurope.com)Picture is fuzzy *Adjust the Contrast and BrightnessControls.Picture bounces or a wavepattern is present in the picture *Move electrical devices that may causeelectrical interference.The power LED is ON (orange)but there’s no video or nopicture.*Computer Power Switch should be in theON position.*Computer Video Card should be snuglyseated in its slot*Make sure monitor’s video cable isproperly connected to the computer.*Inspect monitor’s video cable and makesure none of the pins are bent.*Make sure computer is operational byhitting the CAPS LOCK key on thekeyboard while observing the CAPSLOCK LED. The LED should either turnON or OFF after hitting the CAPS LOCKkey.Missing one of the primarycolors (RED, GREEN, or BLUE) *Inspect the monitor’s video cable andmake sure that none of the pins arebent.
11APPENDIX SPECIFICATIONSCRT Size 43.2cm(17"), Pure Flat and 90ºdeflection, 29mm neck,CRT Viewable ImageSize 40.6cm (16"), diagonalType 0.25mm dot pitch.Video 0.7Vpp, R,G,B AnalogInput Separate Sync. TTL LevelH./V.- Sync. Positive / NegativeScanning H-Frequency 30kHz – 98kHzFrequency V-Frequency 50Hz-160HzMax. Resolution 1600 x 1200Video Dot Rate 200MHzFactory Preset mode :8User Programmable mode : 20Plug & Play VESA DDC1/2BTMEPA ENERGY STAR®ON Mode <120WOFF Mode <5WDimension: Monitor & Base 430(W) × 416(H) × 440(D)mmWeightF1795+: Unit (net) 17.0kgs ( Net )7KlrA: Unit (net) 17.8kgs ( Net )Signal Cable: Attached Mini D-sub 15 Male410402420(ln mm)F1795+
12Switch •Shuttle Knob•Standby Power Switch•OSD Key•Volume(7KlrA)External Controls: Functions •Contrast•Brightness•H-Center•H-Size•V-Center•V-Size•Zoom•Pincushion•Trapezoid•Pin-Balance•Parallelogram•Rotation•6500°K•User Color•9300°K•Degauss•Moire Reduce•Recall•Exit•Select LanguagePlug & Play DDC1/2BPower Management EPA, VESA DPMSPower Consumption ( Maximum ) 120 WattsPre-set Display Area 300mm x 230mmAudio Output(for 7GlrA only) Rated Power 1W rms(Per channel)Regulatory Compliance UL, CSA, FDA, FCC, TÜV/GS, CE,MPR II, TCO’99410307440305(ln mm)4207KlrA
13STANDARD RESOLUTION HORIZONTALFREQUENCY VERTICALFREQUENCYVGA 720 × 400 31.46kHz 70HzVGA 640 × 480 31.46kHz 60HzVESA/85 640 × 480 43kHz 85HzVESA/85 800 × 600 53.6kHz 85HzVESA/85 1024 × 768 68.8kHz 85HzVESA/85 1280× 960 85.938kHz 85HzVESA/85 1280× 1024 91.14kHz 85HzVESA/75 1600× 1200 93.75kHz 75Hz1 561011 1515 - Pin Color Display Signal CablePIN NO. DESCRIPTION PI N NO. DESCRIPTION1. Red 9. NC2. Green 10. Ground3. Blue 11. Monitor Ground4. Ground 12. DDC-Serial Data5. Ground 13. H-Sync6. R-Ground 14. V-Sync / *V-Clk7. G-Ground 15. DDC-Serial Clock8. B-Ground *For DDCFACTORY PRESET TIMING TABLECONNECTOR PIN ASSIGNMENT
14LIMITED THREE-YEAR WARRANTY*forAOC Spectrum Color Monitors sold within EuropeAOC International (Europe) GmbH warrants this product to be free from defectsin material and workmanship for a period of Three (3) years after the originaldate of consumer purchase. During this period, AOC International (Europe)GmbH will, at its option, either repair the defective product with new or rebuiltparts, or replace it with a new or rebuilt product at no charge except as *statedbelow. The defective products that are replaced become the property of AOCInternational (Europe) GmbH.If the product appears to be defective, please contact your local dealer or referto the warranty card when attached to the product.Deliver the product freight pre-paid, along with the dated proof of purchase, tothe AOC Authorized Service Center. If you cannot deliver the product in person:• Pack it in its original shipping container (or equivalent)• Put the RMA number on the address label• Put the RMA number on the shipping carton• Insure it (or assume the risk of loss/damage during shipment)• Pay all shipping charges AOC International (Europe) GmbH is responsible neither for any damage or lossduring inbound transport damage nor to inbound product that was not properlypackaged. AOC International (Europe) GmbH will pay the return shipping charges withinone of the countries specified within this warranty statement. AOC International (Europe) GmbH is not responsible for any costs associatedwith the transportation of product across international borders. This includes theinternational border within the European Union. * This limited warranty does not cover any losses or damages that occur as aresult of• Shipping or improper installation or maintenance• Misuse• Neglect• Any cause other than ordinary commercial or industrial application• Adjustment by non-authorized source• Repair, modification, or installation of options or parts by anyoneother than an AOC Authorized Service Center• Improper environment• Excessive or inadequate heating or air conditioning or electricalpowers failures, surges, or other irregularitiesThis limited warranty does not cover any of the product firmware or hardware
15that you or any third party have modified or altered; you bear the soleresponsibility and liability for any such modification or alteration.ALL EXPRESS AND IMPLIED WARRANTIES FOR THIS PRODUCT(INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FORA PARTICULAR PURPOSE) ARE LIMITED IN DURATION TO A PERIOD OFTHREE (3) YEARS FOR PARTS AND LABOR FROM THE ORIGINAL DATEOF CONSUMER PURCHASE. NO WARRANTIES (EITHER EXPRESSED ORIMPLIED) APPLY AFTER THIS PERIOD.AOC INTERNATIONAL (EUROPE) GMBH OBLIGATIONS AND YOURREMEDIES HEREUNDER ARE SOLELY AND EXCULSIVELY AS STATEDHERE. AOC INTERNATIONAL (EUROPE) GMBH LIABILITY, WHETHERBASED ON CONTRACT, TORT, WARRANTY, STRICT LIABILITY, OR OTHERTHEORY, SHALL NOT EXCEED THE PRICE OF THE INDIVIDUAL UNITWHOSE DEFECT OR DAMAGE IS THE BASIS OF THE CLAIM. IN NO EVENTSHALL AOC INTERNATIONAL (EUROPE) GMBH BE LIABLE FOR ANY LOSSOF PROFITS, LOSS OF USE OR FACILITIES OR EQUIPMENT, OR OTHERINDIRECT, INCIDENTAL, OR CONSEQUENTIAL DAMAGE. SOME STATESDO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL ORCONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION MAY NOT APPLYTO YOU. ALTHOUGH THIS LIMITED WARRANTY GIVES YOU SPECIFICLEGAL RIGHTS, YOU MAY HAVE OTHER RIGHTS, WHICH MAY VARY FROMCOUNTRY TO COUNTRY. THIS LIMITED WARRANTY IS ONLY VALID FORPRODUCTS PURCHASED IN THE MEMBER COUNTRIES OF THEEUROPEAN UNION.

Navigation menu